Connecting HP Officejet Pro 8600 to Verizon JetPack 4G-LTE

Hi, as you can probably guess I am trying to connect my HP Officejet Pro 8600 to my wireless Verizon hotspot. I have tried to use the "Wireless Setup Wizard". When prompted I chose the correct network, and entered the correct password. After some time the printer displays:
Connection Successful
IP: No Link
Network Name: Not applicable
followed by a Hostname and the MAC address of the printer. When I try to view the wireless connection the window states that I am not connected (as suspected). I then printed the "Wireless Network Test Results". It reports "No problems found. Congratulations on the successful setup of your wireless printer." and everything under the "Diagnostics Results" section passes. Under the "Current Configuration" section the correct SSID is displayed, however the IP address comes up as 0.0.0.0 (which means I am not connected?).
Also, I checked the Jetpack's configuration page and the MAC filtering is disabled.
Is it possible to connect this printer to a Verizon Jetpack (MiFi)? If so, what am I doing wrong?
This question was solved.
View Solution.

It looks like the printer is connecting to the network, just not receiving any IP information.
I will provide the simplest solution that typically resolves this issue. To receive the best results, be certain to follow them in order.
1. Power off the JetPack.
2. Disconnect the power to the printer while it is on for 1 minute.
3. Power on the JetPack and wait for the network connection to come back up. This can be easily identified when other devices start connecting to it again.
4. Reconnect the power to the printer and wait for the home screen to finish loading.
5. Press the antenna icon and select Settings.
6. Scroll down and select Restore Network Defaults.
7. Once that is completed, reconnect the printer to the network with the Wireless Setup Wizard.
DHCP, dynamic host configuration protocol, is responsible for assigning IP information to devices automatically as they connect. It is possible to connect to a network without DHCP, there just won't be any communication unless IP settings are set manually.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Similar Messages

Cant WiFi connect HP Officejet Pro 8600 e-All-in-One Printer to internet

I cant WiFi connect HP Officejet Pro 8600 e-All-in-One Printer to internet... at least I think that is the problem. I have followed all the instructions on HP Print and Scan Doctor as well as Troubleshoot HP Installation Failure. My router is running fine for everything else and I have entered the static address for the printer into the router. It appears that my printer believes it is connected to my WiFi (Ihave WPS it multiple times), but when I type it's IP address into my IE nothing shows up. My router doesn't appear to see the printer either. I have the latest driver installed on my computer. I suspect this may be a router issue: new router Asus Double 450 Mbps N Router (Dual band - but it appears my router is using the 2.4Hz band to communicate with WPS). Windows 7 64.
Any help is appreciated!
This question was solved.
View Solution.

Hello NRHII,
Welcome to the HP Forums!
I understand you're unable to connect the Officejet 8600 over a wireless connection. I will do my best to assist you! I would recommend power cycling the router, printer and computer:
1) Turn off your printer
2) Disconnect the power cord from the back of the router
3) Restart your computer
4) Wait less than 60 seconds, plug the power cord back into the router
5) Turn your printer back on, wait for the computer to turn on
Is the wireless light blinking on your printer? If so, please reconnect the wireless on your printer by using the wireless setup wizard: (This information is stated here.)
On the printer touch screen, touch the Right Arrow ( ) to display the second navigation screen.
Touch the Setup icon ( ).
Touch Network , touch Wireless Setup Wizard , and then touch Continue . The printer searches for available networks.
Touch the name of your network, and then touch OK .
If prompted, enter the network password, and then touch OK . The printer connects to the network.
Also, as I was typing this post TreeFrog posted some great information to follow.
Have you followed this entire HP document on Printer Does Not Maintain Wireless Connection? If not, follow this document. Please post your results, as I will be looking forward to hearing from you.
Have a great day!
I worked on behalf of HP.

Air print on iPad does not connect to officejet pro 8600 plus

My macbook prints fine wirelessly to our hp officejet pro 8600 plus with an arris TC862 router. IPad, however, will not. Is there an easy fix that will not disrupt my computer's wireless connection because I did not find it easy to set up, so don't really want to redo that connection. bluetooth is off and ipad and printer are on same network.
Thanks in advance!
Hull1968

Hi,
You may have already tried this but try restarting your apple device - It's a simple fix that sometimes helps re-establish the connection to the printer.
Other things to check would be that there have been no recent changes to the wifi password.
"Although I work for HP, I'm speaking for myself and not on behalf of HP"
"Say "Thanks" by clicking the Kudos Star in the post that helped you.
--Please mark the post that solves your problem as "Accepted Solution"

Officejet pro 8600 will not connect to wireless network

I have an new Officejet Pro 8600 that I am trying to set up. I have run the the wireless network setup wizard multiple times. It recognizes the wireless network router asks for the WEP code and then thinks for about 5 minutes before returning a message: "Unable to connect to the network"
The wireless network test results suggestes that MAC address filtering may be the problem. There is no MAC filtering function activated on our wireless router.
The wireless router is a Verizon Actiontec MI424-WR 802.11 b & n
We have computers running both Windows XP and MAC OS X.
One of the reasons that we purchased this printer is for the wireless capabilities. If it will not conect to the web then it may be going back.

Hello,
Based on the provided details, I believe the issue have something to do with the wireless security settings of your router.
Please follow the steps below to access the Advanced Security Settings:
http://www22.verizon.com/ResidentialHelp/FiOSInternet/Networking/Setup/ActiontecMI424/125511.htm
Below you will see the Network Authentication settings.
Select either Open System Authentication or Both.
Shared Key Authentication is not supported by the printer, and i believe this might be the cause for the connection failure.
Please let me know of any change,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

My HP OfficeJet Pro 8600 won't connect to my wireless router

This is bizarre. I have had my HP OfficeJet Pro 8600 for about 6 months. It has generally worked fine, and we have used it wirelessly only. But now it refuses to connect to the router. It can FIND the router, and it can find other networks in the area, but it won't connect to the router. I ran the Wireless Network Test, and the results say:
Wireless On - Pass // Wireless Working - Pass //
Network Name (SSID) found - Pass // Wireless Networks Detected - 9
Printer Settings Consistent with Wireless Router Settings - Pass / No Filtering - FAIL //
So it recommends solution as follows: "1 If MAC Address filtering is enabled, and you would like to keep it enabled, you must add the Mac address of your printer to the list of permitted devices for your router before continuing."
Except, guess what, I don't have MAC Address filtering enabled. I wouldn't know how to do that, much less check for it.
Also, before today, this was never a problem. HELP!
Thanks....
If you are interested, here's more detail and background.
Before today, the only problem we have had is that frequently our Apple laptop (OS X 10.6) has trouble connecting to the printer. This has been odd because the printer is connected to the network, and so is the laptop, but the laptop can't find the printer - it thinks the printer is "offline" (even though it's not). Usually, if I wait a while, it will find the printer, and it will resolve itself work fine. If not, we sometimes have found that it can fix itself if you restart the laptop -- restarting the printer does not make a difference. In fact, I did exactly that today, and it resolved itself. And I printed. Fine, right?
But then I wanted to do more printing, and the problem of the laptop not finding the printer came up again, so I decided to really "get to the bottom of this." I don't remember exactly what I did, but somehow I was persuaded by the online help, that the correct solution would be to go into my System Preferences / Print and Fax, and click on the "-", which de-installs the printer, with the idea of re-installing the printer. But then when I tried to re-install the printer, it could not find the printer. Ugh! Wierdly, it found an 8600 Scanner, but not an 8600 printers. After installing and de-installing the 8600 scanner a few times, I eventually deinstalled everything, and I decided to start from scratch. I got my HP disk, and installed all the software again from the beginning (even though it was already there), and then it looked for my printer, but couldn't find it. So then I got a USB cord, and plugged that in.
So, now I have a situation where I do have a working printer via the USB cord, but no wireless connection at all. In particular, since the Office Jet Pro 8600 won't connect to the router, I don't know what else to do. My Apple MacBook pro is 2 feet away from the printer, and it is connected to the router just fine (as is my blackberry), and I have never before had a problem connecting to the wireless router by the printer.
Any suggestions?

There are two things that can trip the mac filtering test to fail: actual MAC address filtering setup (sounds like this is not the case) and using wireless channel 6 or automatic for wireless channel in the wireless network settings (in the router). Since it does show failed for MAC filtering and you do not use this option, try changing the wireless channel in the router to 1 or 11. Those two channels provide the best compatibility with printers due to less interference. Almost everything defaults to auto or 6 for the channel and this causes a lot of interference. This change should not affect anything at all. To do this, you may need to contact the router manufacturer as the process differs from router to router.
What brand and model is the router?
Has anything in the network settings changed at all?
What version is the Mac OS X? There may be additional steps to take as it sounds like there are two separate issues involved and this could be revisited later.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Officejet Pro 8600 Plus connection issue - HELP!

I have a strange issue: after some hours, the communication link is dropped between the computer and printer. When this happens, IE becomes unusable and will not connect to anything. This is replicated on three XP home machines. The fourth, a vista ultimate machine, does not seem to be affected (yet). I get the "scan to computer is disabled" error. It cannot be re-enabled. At this point I cannot print either. I can reach the embedded web server on the printer via firefox and can still surf using firefox. I can ping the printer, but again once the connection is dropped, no printing or scanning to the computer. The only thing I've found that resolves the issue (temporarily) is to reboot the computer, which just starts the cycle again.
last night I installed the software on an XP machine and the laptop to test when the connection dropped. They lasted from 7pm Monday until I got home at 5pm Tues. The machines were not used. Once I started using them (firefox only), then they dropped the connection within a half hour of each other around 7pm. The other XP machine lasted from 7pm Mon until 7am tues, when my wife started using it and then noticed it dropped sometime that tues between 7 and 9AM. An 11am tues reboot ran OK until 10 pm tues when connection was lost again (and IE is now dead). The Vista machine has been running since 7pm monday until now (930pm tues) and still seems to be holding.
printer hardwired, to router, static IP, 100-full link speed (also tried 10-half)
router dlink di-655
two XP machines are hardwired, vista is hardwired, and last xp machine is a laptop on wireless.
I've swapped cables rebooted and reinstalled multiple times. I must have a file a mile long on the support phone line. They were unable to fix it. I asked this to be escalated, but who knows when I'll get a response.
I've toggled firewalls - XP built in
I've uninstalled anti virus software
I've even put up with crazy suggestions from tech support like changing the router channel (uhh, it is wired!)
one xp machine had an AIO 4215 hooked via USB and the others printed to it via network, but the printer has been deleted from the networked machines.
I can ping 127.0.0.1 which is supposed to indicate the tcp service is OK.
I have not reset winsock .. I can see one machine being bad, but three????
malware / virus scan shows no issues. Again one maybe, but three??
The only thing I can think of is that there is something in the XP networking stack that conflicts with the new 8600 software as hours pass. Perhaps there is some polling operation that goes on then dies after some time, then it kills IE as it dies.
When the printer works it is great, but rebooting is not a permanent solution to this.
any suggestions would be greatly appreciated!!!!!! I am stumped and so is tech support. They are sending it to engineering, but who knows when they will respond.
thanks in advance.
This question was solved.
View Solution.

well it looks like I have a working solution ... I downloaded a freeware file called process.exe . I made a cmd file via notepad with the following contents:
rem this is to keep the HP network printer communicating with the desktops
rem
process -k "hpnetworkcommunicator.exe"
rem
process -k "scantopcactivationapp.exe"
rem
"C:\Program Files\HP\HP Officejet Pro 8600\Bin\HPNetworkcommunicator.exe"
rem
Start "" "C:\Program Files\HP\HP Officejet Pro 8600\Bin\ScanToPCActivationApp.exe" -deviceID CNXXXX:NW -scfn "HP Officejet Pro 8600 (Network)"
the XXXX is your printer serial number with an extra character or two. Pull that number from the port tab after you pull up "properties" for the 8600 printer.
This cmd file basically restarts the printer link. It opens a command window that launches the program to re-establish the link.. then it closes the command window. The launched program shows that the communication link is dead (just for a few seconds), but then it makes the connection... THEN you hit the close button and coninue your work until it dies again.
I may have it autorun every X hours if I can narrow down a good time. Until then I have a shortcut on the desktop to "FIX HP LINK" ... I only had to do this for my XP machines, as the vista one seemed OK.
What ticks me off is that I shouldn't have to do all of this diagnosis. It would be nice if there is a fix in the pipeline so the link stays stable al the time. I've spent hours trying to figure this crap out.
Anyhow, I hope the time I spent helps someone. PS, thanks to the OJ6500 thread that had the info for the scantopcactivationapp.exe program.
PS ... I'm still waiting for an engineer to contact me, if any HP employees are reading this.
PSS I haven't tried this without killing and restarting the hpnetworkcommunicator stuff, but it works for now.

Can't get officeJet Pro 8600 wireless to connect

This is so frustrating. I just bought a HP Officejet Pro 8600 and am trying to set up the wireless connection to my ATT-supplied Netgear 7550 router. I keep getting a message that "MAC address filtering is enabled on your wireless router" even though I have checked in the router setup and I am certain that it is not (it clearly says MAC is "not enabled"). I talked to the ATT tech support and they agreed--we even hard-rebooted the router and re-installed it and it seems to be working as intended. I have unplugged and re-plugged the printer. I have spent over 2 hours and keep getting the same message.
Help?
Oh, I have also tried the HP Dr. software taht has been recommended to others, but it does not find my printer.

Thanks for the reply. I believe I already tried that once. I added the printer MAC address and selected "allow this address" or something like that. It did not seem to help, so I went back and disabled the MAC filtering completely. But, I can try that again. Certainly won't hurt.

Scan To network folder - HP officejet pro 8600 cannot connect.

Good morning,
For the last week or so, My officejet pro 8600 has been giving me the error
"Cannot connect to \\REDACTED\Public\Scans. Make sure the remote computer is turned on."
It will correct itself if we restart the computer/printer in question. but this only solves the issue for approx 6-7 hours.
Things i have done to attempt to fix this.
Set a static ip address for both the computer in question and the printer itself.
updated the IP address using the HP tool.
reinstalled the HP office program.
Set DMZ for both the computer and printer.
Set the public scans folder to zero security( so anyone connected to the network can gain unrestricted access)
re-setup the network feature on the printer itself.
however now i am at a loss.
Any help would be great.

Hi @Prophet1986,
Welcome to the HP Forums!
I understand that you cannot connect in order to scan to your network folder with your HP Officejet 8600. I am sorry to hear this, but I am happy to help!
Are you able to make copies? Setting Up the Printer to Print and Copy from Tray 1 and Tray 2.
Are you connected wirelessly? Or with an Ethernet cable?
Also, what operating system are you using? Windows or Mac? What version? If you do not know the Operating System you are using, please visit this website. Whatsmyos.
In the meantime, please try the following:
Make sure the printer's power cable is plugged directly into the wall outlet, not a surge protector. Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector. This applies to Inkjet printers as well.
Firmware update. Getting Printer Updates for HP Officejet Pro 8600 (N911), Officejet 6600 (H711) and Officejet 6700 P....
In the meantime, if you are using Windows, please see this guide, HP Scan to Network Folder or Digital Fax to Network Folder Fails to Install or Function in Windows w....
Printer Does Not Maintain Wireless Connection. (This guide will help you maintain the connection, if you are wireless).
Hope this information is helpful, and hope to hear from you soon!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Hp officejet pro 8600 plus - connected to the wireless but AirPrint not working

i have an hp officejet pro 8600 plus. had it for 6 months or so. intial setup went fine...connected to the wireless network with no problems...airprint worked instantly from all of my apple devices. recently, in the last 3 weeks, airprint has stopped working. when i turn the printer off and turn it back on, airprint will work for about 5 minutes. but then it stops working. it is like the printer is losing wireless connectivity, but the wirless diagnostics show it to be connected fine.
i have an apple airport exptreme router. it is showing to be connected just fine to the network and i can see the printer's mac address as a wireless client in the Airport Utility.
any ideas?

Hi henryje,
Sorry to hear you are experiencing these issues. I would be glad to help.
Try changing the channel on the AirPort Extreme router to channel 11 or any channel that seem less congested.
You can check you network channel environment by printing a Network Configuration page from the Wireless Settings menu on printer front panel. The second page of the printout will display all detected networks by the printer listed by signal strength. You can also use InSSIDer: http://www.techspot.com/downloads/5936-inssider.html
Printers also do not support the 5GHz band, so if your network uses 5GHz only, you can disable this in the AirPort Extreme router config page.
Say Thanks by clicking the Thumbs Up in the post that helped you.

HP Officejet Pro 8600-a: Can't Fax after converting to Verizon Home Phone

Can anyone provide me with a solution?
My HP Officejet Pro 8600 All In One worked just perfectly prior to converting our home telephone from AT&T/Frontier to Verizon Home phone service.
Now, I can't send nor receive a fax. What I've read on the "net", it appears I will need to junk my HP OfficeJet Pro 8600 and buy a new unit compatible with Verizon Home phone service. It would be a shame to junk a unit that is not even 1 year old.
My hope is someone here has come across a solution!
Thank you for your help.

Thank you all for your input.
Please understand I did not rush into making this Home Phone change to Verizon. I met with the same Verizon "agent" 3 separate days at 3 separate times. Together we went over point-by-point all of my requirements. We did cover faxing capabilities. Still I was sold a product that didn't fit my basic needs.
Hopefully, I am still within my window to cancel.
I need to be able to fax, so I have a lot of work to do to straighten this mess out.
Thanks again!

HP Officejet Pro 8600 Plus - no wireless connection

Hi,
I am now onto my second HP Officejet Pro 8600 Plus. The previous one froze entirely. This one switches on ok, but is unable to connect to my wireless router (even when it is inches away from the router). The blue wireless indicator is constantly flashing, and when I try to set up the wireless connection is just says "searching" and the screen never changes. I have tried restoring factory defaults and restoring network defaults.
Does anyone have a solution please?
Glynn

You are not connecting to your wireless router if the blue (wireless) light is flashing. Move the printer to 3 feet away from the router. Set the router to a fixed wireless channel like 1, 6 or 11 never 'auto' try all three. Use 20 Mhz only or 145Mbps depending on the router. Power cycle both. Connect to your SSID using WPA2-AES encryption with your password. Have to connect to the router successfully first.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

HP Officejet Pro 8600 Network connection error message in EWS

I just got an Officejet Pro 8600 Premium. The printer is connected to the network via a network cable. When navigating through the EWS, sometimes the message "Network connection error. Check network and try again." message is shown (the message could appear in various pages, such as Settings, Tools, etc.). Refreshing the page should get rid of the message.
At first, I suspected if it was a problem with the network. So I pinged the printer's ip address continuously. It did not miss a single beat. The printer prints and scans well via the network. So I think the error may be caused by something inside of the print, such as bug of EWS software, or internal error.
Anyone see the same message during the use? Any suggestion? Does it indicate there is hardware problem with the printer? Thanks.

HP Support has escalated the case. I referred this thread in the support request. Hopefully, they can have a look at the issue.
For me, the only setting does not stick is "Use the same time zone set on this computer" in Settings\Date & Time. I've created another ticket for this issue. 8500A has the same problem.
You can try to restart the EWS. Unplug the power cord while the printer is on. Then wait 15 sec and reconnect the power cord. Press the power button if the printer does not turn on by itself.
If you would like to reset to the printer and reconfigure from scratch, you can check here: http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup/How-to-reset-Officejet-Pro-8600-Plus-P...

HP Officejet Pro 8600 Plus (UK purchase) will not connect to wired ethernet network

Hi
We have an HP Officejet Pro 8600 Plus (purchase here in UK approx 9-12 months ago) which has sort of worked OK wirelessly but finance industry compliance requirements now require me to connect to it by normal ethernet cable.
When I disable wireless and plug in a (tested and working) ethernet cable it does nothing. I have done a factory reset (via the screen menu) to remove any previous settings. Turned off, turned on, still nothing.
I have restored Network defaults also using the menu command within settings - network; no difference.
In Network - wired summary the screen says:
IP: Not applicable
MAC: xxxxxxxxxxx (not for sharing here)
Hostname: xxxxxxxxx (not for sharing here)
Wireless Direct: Off
I have tried it with IP settings turned to Automatic (DHCP) - no joy.
I have tried it with IP settings turned to Manual(Static) - when i then type in the static IP address that is within the router range (but outside the DHCP reserved range) as soon as I press Done, the settings are lost i.e. 192.168.0.102 - push 'Done' and the IP goes back to 000.000.000.000
The same when entering the default gateway and subnet masks.
I have restored to defaults several times, tried manual and DHCP several times, no joy.
Please let me have some serious suggestions at the earliest opportunity. Just to reiterate I have tested the network connection and cables with other ethernet equipment and they are working. My questions include:
1. Anyone know how to make this printer actually store the manually entered IP addresses etc?
2. What am I missing about the wired setup?
3. Is this a known issue? Is it an issue with the hardware ethernet socket or something?
4. Also in this forum there are references to a Hard Factory reset that is apparently different to the menu 'Reset to Factory Defaults' but links to an article about it just give a 404 error, not found. [Does HP actually have two different levels of Factory Default and if so, God knows why! Does anyone know a working link to this information please?

Hello Qw8, welcome to the forums!
I read your post about not being able to successfully install your Officejet 8600 Plus to your wired network. I will do my best to find suggestions for you to try. I would first like to know which Operating System you are installing the printer on to help me with my research.
If you haven't already, run the installation (HP Officejet Pro 8600 Plus e-All-in-One Printer - N911g Drivers) with your security and firewalls disabled to see if the proper connection can be made.
I do see you ask about other resets and there are others however, at this stage they may not be needed. If they are, I can send you a private message at that time with that information.
Please let me know your OS and we will go from there!
Have a wonderful weekend
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Wireless Printing to OfficeJet Pro 8600 Connected to Ethernet Network

We have an OfficeJet Pro 8600 that is connected to our home's Ethernet network and would like to print to it from devices such as laptops, phones, and tablets. Any attempt to turn the printer's wireless capabilities on results in a command to disconnect the Ethernet cable, which we would prefer not to do.
Is there any way to "have our cake and eat it too", retaining the Ethernet connection while having the ability to print wirelessly? While useful, HP's ePrint doesn't offer the direct-from-application convenience we desire.

Hi,
By the book, the following setup should work:
Please use the following manual to set them up:
http://h10032.www1.hp.com/ctg/Manual/c00389927.pdf
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

'Connection Error' message on HP Officejet Pro 8600

Hi. Would really appreciate help on this. I have a HP Officejet Pro 8600. Working wirelessly. All connections are fine, print & scan etc works fine. However when i touch the screen on the printer, for example to click 'Apps', I get the following message:
' Connection Error. The printer was unable to connect to the server. Check your internet connection and try again.'
I don't understand why I am getting this message, nor how to resolve it. The connection seems fine because I am printing and scanning wirelessly without an issue.
Can anyone help me on this? Thanks

I know this will sound like it shouldn't work, but turn the printer off and back on, then try the apps again. If that doesn't work, or you've tried it, turn off your router and your printer. Turn your router back on, but leave the printer turned off. Wait for the router to stabalize, about 1-2 minutes normally. Turn the printer back on and try the apps. If that doesn't work, let me know.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Connecting HP Officejet Pro 8600 to Verizon JetPack 4G-LTE

Similar Messages

Maybe you are looking for