Connecting Motorola SB6121 Cable Modem and AirPort Extreme

I moved into a new house a couple of days ago so of course the first thing that I needed to do was get the home wireless up and running. My ISP is through Comcast. I purchased my own cable modem (Motorola SB6121) instead of renting and used my own AirPort Extreme as the wireless router.
First, if you're purchasing your own cable modem, you will need to contact your ISP and provide them with the HFC MAC ID on the cable modem. Once you've gone through the motions, you will be able to connect your Mac (in my case Macbook) directly to the modem via ethernet cable and access the internet.
Issue:
When I connected the SB6121 to the AE, I could connect wirelessly to the AE, but I did not have access to the internet. So, basically the SB6121 and the AE were not talking to each other despite being physically connected via ethernet cable.
Solution:
After days of searching for online answers and forums (and trying different solutions) I was able to successfully get everything up and running. Make sure that you have 2 ethernet cables available.
Here are the steps.
I restored my AE to factory settings just to keep everything simple. Here are instructions: http://support.apple.com/kb/HT3728 Once you've restored your AE, make sure that both the AE and the cable modem are unplugged from their power sources.
Plug in the power to the SB6121.
Connect your SB6121 directly to your laptop via Ethernet cable. Test to ensure that you have internet accessibility by going to any website.
Remove the ethernet cable from your laptop and plug it into the "internet in" jack in the back of the AE.
Power up the AE.
Connect your laptop to the back of the AE using ethernet cable #2.
Launch a browser. You should now be able to successfully connect to any website.
Assuming that you reset your AE to factory settings, it should just be broadcasting the generic "Airport Extreme" SSID. Disconnect the ethernet cable and connect using wireless to the SSID. Launch a browser and you should be able to connect to the internet.
You can now use the AirPort Utility to configure the AirPort settings.
I assume that this solution would work with any of the base stations.

I was having the exact same issue tonight.  Just purchased the AE Model A1408 and haven't been able to maintain an internet connection on my iMac whenever I tried hooking it up via the Airport Utility application.  So after I had the SB6121 connected to the AE and the AE connected to my PC with no luck, I then went to the Network icon in System Preferences.  Clicked on "Assist me...".  Then clicked on "Diagnostics..." and followed the directions which basically had me first power down the SB6121 modem and power it back up.  Then I powered down the AE router and powered it back up.  At that point I was now getting an internet connection.  I then took my ipad 2 and went to the Wi-Fi settings and noticed it was asking me to setup a network through my AE.  I selected that and went through the simple steps to set up the network and password and now it all works.  I am a novice so don't ask me why but I now get a green solid light on my AE.  I can connect other devices wirelessly. I can still access the internet on my iMac.  For whatever reason, using the Airport Utility on the iMac doesn't work in my case and using my ipad to set up the wireless network did the job.

Similar Messages

  • Please help me connect eMac, cable modem, and Airport Extreme Base Station

    I connected Ethernet cord from cable modem to Airport Extreme Base Station and then another Ethernet cord from Airport Extreme Base Station to eMac, but I could not get internet access on my eMac that way. I'm only getting internet access by directly connecting eMac to cable modem. Can someone please help me with a step by step explanation of how to set these 3 machines up so that I can have internet access on both my eMac and, wirelessly, on my new MacBook. Thank you very much in advance.
    eMac & MacBook   Mac OS X (10.3)  
    eMac & MacBook   Mac OS X (10.3)  
    eMac & MacBook   Mac OS X (10.3)  

    jenngee, Welcome to the discussion area!
    Ensure that you power off the cable modem for a minute or so when you switch it to another Ethernet device.
    Ensure that you are connecting the WAN port of the AirPort Extreme base station (AEBS) to the cable modem. The eMac should connect to the LAN port.
    The steps for setting this up can be found in the "Designing AirPort Networks" (direct PDF link) document. Look through that document and try to get it setup. Then return here if you have more questions. Don't forget to post what you tried and the issues you encountered.

  • Should Iplace my ethernet switch between cable modem and airport extreme?

    I'm looking for the best placement of an ethernet switch in my home network.
    Should I place it "between" my cable modem and my AEBS or connect it to the output from my AEBS?
    The current placement is connected to one of the AEBS outputs.
    I'm attempting to set up an old AE (802.11 a/g from 2004) with a different network name than my home network, that I'm trying to set up for a college dorm network and each time I plug the AE to the switch to confirm its functionality, my network gets a little confused.
    Help appreciated.
    Regards,
    jim P.

    Should I place it "between" my cable modem and my AEBS or connect it to the output from my AEBS?
    This all depends on whether you have a simple modem.....or.....a modem/router or gateway combination device.
    If  you have a simple modem, you cannot place the switch between the modem and the AEBS. The reason for this is that the modem can only deliver one valid IP address and it will be a matter of chance as to which of the devices connected to the switch receives it. The other device connected to the switch will not be able to access the Internet.
    If you have a modem/router or gateway type of device, you can place the switch after the modem/router and before the AEBS if you wish, although there is really no advantage to doing so unless this makes things easier for you in terms of hook up.
    If none of this makes much sense at all to you, leave the switch in its current location connected to one of the LAN <-> ports on the AEBS since that setup will work correctly no matter what type of "modem" that you might have.

  • I have an Airport Extreme, I want to replace it with a Time Capsule.  I swapped my cables to the new TC, unplugged both Cox Cable modem and Airport Extreme.  Started up by plugging A/C power for Cox Cable modem, then power to TC.  Result is blinking amber

    I tried unplugging again and restarting the TC first, still gets blinking amber light.  I even reset the TC because I was using it for backups only in the network, I just want to move it to the primary position.  I don't even get the option of starting a new network.
    I need help.

    Blinking amber light is not the issue.. that will involve lots of issues due to your reset.
    Make sure you have a computer plugged into the TC by ethernet.. do not do setups over wireless.
    Even if you need to do the setup in complete isolation that doesn't matter.. it will work when you return it to the network.
    Do a full factory reset.. I am not sure what resets you have done up to now.. full factory means you hold in reset before applying power.. and keep holding in reset until the front led flashes rapidly. About 10sec.
    The TC must be in router mode if your cable modem is only a modem.. but I don't know if your cable modem is pure modem or modem router.. if the later then the TC should be in router bridged mode.
    Once you have that right.. plug it back into the modem if you had to remove it..
    Power cycle again if you need to. It can take 15min or more of modem off to reset the cable setting for MAC address.
    Then you can setup wireless, although you can also do it whilst connected by ethernet which is usually better.
    What airport utility are you using.. the latest one is too automatic.. stop any attempt to automate the setup and do it manually if you get stuck.
    Even use the old utility is sometimes better.. 5.6 can be loaded even on Mountain Lion with a bit of a fiddle.

  • Power backup for dsl modem and Airport Extreme

    Does anyone here have backup power for a dsl modem and Airport Extreme that is successful? I have a name brand power backup and when the power goes off both the dsl modem and Airport Extreme remain on; however, the network connection is lost so the fact that they remain on doesn't help. I have been unable to find anything about this problem on the internet generally and consultation with a well-known squad person has not helped. Any thoughts about this will be welcome.

    Yes, I agree. But since the backup power keeps the modem powered, why doesn't the dsl connection continue? The squad person I talked with told me that the speed with which the backup power units replace power during an outage is about the same across different backup brands/units (I don't recall the speed but it was in milliseconds) and should be quick enough to retain the dsl connection. Doesn't happen.

  • How to connect my iPad, Brother printer, and AirPort Extreme?

    How to connect my iPad, Brother printer, and AirPort Extreme?

    I don't believe any of the Brother printers are AirPrint-enabled. Is your Brother printer network-ready? That is, does is support either/both a wired or wireless connection or just uses USB to connect?

  • Adding QoS with a switch between modem and Airport Extreme?

    Since the Airport Extreme does not offer any QoS,  is this something I can add to my network with a QoS capable unmanaged network switch such as this one -  http://www.dlink.com/ca/en/home-solutions/connect/switches/dgs-105-5-port-gigabi t-ethernet-switch    ?
    My network would then be wired like this;
    Cable Mode --->  D-Link DGS-105 --> Airport Extreme --> wired / wifi network devices
    (I might add a switch after the Airport Extreme either way at some point to increase the number of wired devices)
    Nothing other than the cable modem and router would be plugged into the D-Link switch...  -  but will this actually make a difference, will it cause any grief on my home network?  Is there a better way?
    If its relevent,  the primary reason I'm thinking about QoS is so that video chatting, streaming (on AppleTV or computers), or online gaming isn't interrupted by other devices browsing the web, downloading, etc.   I've got good bandwidth from my ISP, but in my house there are 3 Apple TV's, 4 computers, 3 iPhones, and 2 Xboxes......

    Based on your goal, I would suggest that you take a look at this article. With QoS you are controlling which traffic gets priority going upstream to your ISP, not the other way around. Instead, I believe you what you really want is to implement a form of VLAN. Like QoS, Apple routers do not natively support VLANs. You would need a router, like a Cisco RVS4000 to do this. VLANs are not dependent on physical switches, although you can assign a separate VLAN segement, one to each Ethernet port of the router. You can then attach the AirPort to one of the Cisco's VLAN segments. Any device, wired or wireless, connected to the AirPort would get the same priority.

  • Vonage between cable modem and Airport Express is a problem

    I have my Comcast cable modem connected via Ethernet to the Vonage box which is connected via Ethernet cable to my Airport Express. When I try to connect wirelessly via my Powerbook it's a crapshoot whether or not I can connect to the internet. Mostly the quality is very poor if you can connect at all. If I cut the Vonage out of the equation hooking the cable modem to the Airport Express it works perfect. So Vonage is my problem and I need to change some settings either with my computer or my Airport Express, but which ones? I've been given several different ideas from the information I've sifted through (i.e. change the DNS, change the sharing prefs, get a hard wired router). Oddly enough an old HP computer I have in the basement connected to the internet via another Airport Express has no problems with connection at all. If someone could let me know which of these fixes I am preparing to try would work the best I would appreciate it.

    Interesting. So you have two Airport Express devices configured into a WDS, with the one upstairs functioning as the main base station and the one downstairs functioning as a remote base station. And your PC downstairs connected to the remote base station has no problems connecting to the internet. Is that PC cabled to the Airport Express, or does it connect wirelessly to the remote Airport Express?
    What happens if you bring the Powerbook downstairs to where the PC now resides. Does the Powerbook then get the same great internet connection as the PC?

  • Can i use one router connected to my cable modem and another....

    can i use one router to connect to my cable modem them have another (not connected to a modem) and a wireless reciver so i can plug my xbox 360 into it?

     Yes you can do that ... but you need to configure the computer connect to the Router using Cable ....
    Afterwards ... you can work on mutiple computers ...

  • How do I connect my motorola sb6121 cable modem to my airport express

    I have just switched from DSL to cable internet and am having a tough time connecting my modem to my Airport Express so that I will have a wireless router.

    Plug in the ethernet.

  • Problems with Comcast (Motorola) modem and Airport Extreme

    I have a very strange problem which I have been unable to solve, nor able to find a solution on Apple Support or anywhere else by Googling it.
    I switched back to Comcast/Xfinity, hooked up the Motorola surfboard SB5120 modem:
    My primary Macbook Pro connects to the Internet, but (and this is bizarre!) the AirPort Extreme is flashing yellow with the errors listed as a) no Internet conncetion, and b) no DNS server
    All other Wi-Fi devices are *unable* to connect to the Internet; they are connecting to the home network, but nothing else.
    I did a "hard" reset of the AE, and setup the home network from scratch, same problems:  one Macbook connects, nothing else does.
    I have power cycled everything multiple times (even unplugging EVERY cable for 30 minutes, then reconnecting), spent the better part of 6 hours trying tor resolve this. 
    Any other settings to change?
    In AirPort Utility colors:
    Green for Internet
    Flashing Yellow for AirPort Extreme (errors: a) no Internet conncetion, and b) no DNS server)
    Green for AirPort Express
    sub-menus:
    1) Internet, set to "DHCP", nothing listed for IP Address; the Subnet Mask and Router Address have assigned numberes; the last three windows are empty.
    2) Wireless, set to "WPA2 Personal"
    3) Network, set to "Off (Bridge Mode)
    Any solutions would be most welcomed - the idiot at Comcast was insultingly unhelpful.  He said that since I was able to successfully connect to the Internet, and that the modem was successfully pinging back to Comcast, that the problem was with the AirPort Extreme.

    Many thanks for your reply.  I think number 3) below gets to the crux:
    1) The MBP is on my network, for sure, not a neighbor's.  I'm doing all of this wirelessly, though tested the modem via Ethernet to make sure the modem was working.
    2) I reverted to the Verizon DSL modem, it did a handshake with the AE, and all the computers were successfully connected in seconds. 
    3)  Network set to "Off (Bridge Mode)" is how all the computers are successfully connecting via Verizon, so what am I doing wrong when using Comcast?  If I set it to "DHCP and NAT" or "DHCP only" I would have to enter a range of DHCP addresses (Comcast's *might* be 192.168.100.1, but not entirely sure (any help on that - might solve the problem?)
    Extreme/Express - that was a mistake.  I'm solely using an Extreme for this setup, though I also have an Express, I've temporarily taken it out of the network to try to resolve the issues.
    Thanks again!

  • Motorola SB4200E Cable modem and AEBS no Internet connection

    Hello
    I've bought the new AEBS from an Apple Store in the U.S. Got back home in France thinking it's gonna be an easy ride setting up my new faster and longer range capable wireless network. After all that's what Apple says: "easy setup ... in most cases ". After ten hours trying different settings, no way to get an Internet connection !
    The AEBS distributes IPs to the connected clients but cannot get an Internet address from the cable modem.
    My configuration :
    Motorola cable modem (SB4200E) : configured as DHCP server
    Client computers:
    iMac Core Duo connected to the AEBS via Ethernet
    Macbook Pro Core 2 Duo wirelessly connected to AEBS
    MacPro
    AEBS:
    Wireless Security : WPA2 Personal
    Radio mode 802.11n only (5 Ghz)
    Channel : Automatic
    No Access control
    I've tried to reboot, reset, ... the cable modem without success.
    Oh forgot to say that my old 54g Netgear router is able to reach my MacPro in the bedroom where the AEBS is no show ! (Twice the range ???) and took me 30 seconds to configure.
    Up until now AEBS has only been dissapointment and frustration.
    Thanks for any help.

    I ended up using my new AEBS in bridge mode and keep my "old" Netgear 54g for Internet connection.
    Some pros though: I got a 10 MB/sec transfert rate between my wireless Macbook Pro and my wired iMac both connected to the AEBS.
    Some cons: range is far from what I dreamt of (lesser range than the Netgear 54g at the same location in the room)
    My HP Laserjet 1020 Printer sometimes shows up in the "Printers pane" and suddenly disappears and even when it's there, printing doesn't work !
    Might come from the driver though as this printer has no official driver available for OS X (I use the 1022 driver instead)
    Welcome to Apple world !
    Don't misunderstand my words here, I like Apple products very much, I got three Intel Macs at home, but being an Apple product doesn't ALWAYS go with plug and play. A few software upgrades might make this AEBS a very good product though.
    Macbook Pro   Mac OS X (10.4.8)  

  • I just bought a mac mini...can i just connect an ethernet cable to the airport extreme and set up the mini through an existing mac

    I just took the mini out of the box and hooked it up to the airport extreme through a direct ethernet cable between the two.  Can i find the mini and set it up through an existing mac that is also hard wired to the network?  Help would be greatly appreciated.

    Thank you for your response.. I don't have a monitor nor a wireless keyboard to use on the mac mini...apple salesguy at bb tells me that I can hook up the mini to the ethernet port of my airport extreme and find the mini using finder on my 27 inch mac.
    that my regular mac would see everything on the mini and that i can proceed to set everything on the mini through my regular mac...
    I am trying to purchase the server software from the app store and turn the mini into a server..
    that is what i am attempting to do.

  • I have an older Airport Base Snow that I gave to my brother to use for his apartment. It's connected to a cable modem and I have a network but it is not protected. How do I set a password? There is no computer in this setup, just an iPad

    I Have an older Snow Airport Base that I gave to my brother to use in his apartment. It is connected to a cable router. I have a network established but it is not secure. How do I password protect this network? There is no computer in this setup, only an iPad. Thanks!

    If this base station is actually the "snow" then you will need a Mac or PC that can run a version of the AirPort Utility that can administer this "very old" 802.11b base station. You won't be able to do so with an iOS device or Mac running Lion or newer OS.

  • Wired connection to cable modem.  Airport extreme has to connect to internet if computer goes to screen saver.  Any way around this?

    Airport extreme has to connect to internet if computer goes to screen saver.  Any way around this?

    Describe the issue in more detail.. as it doesn't currently make sense.. the AE should always be connected to the internet. It should never disconnect.. but the computer can fail to connect to wireless after sleep.. that is common problem.
    See Tesserax docos if you have wireless connect issues after sleep.
    https://discussions.apple.com/docs/DOC-3411

Maybe you are looking for