Connecting my airport extreme to comcast cable modem-- AGHHH

I've had three Comcast techies to my house since switching over to their triple play offer. Today, I finally got connected to the Internet, through their cable wired into my house, and connecting their modem to my Mac mini (which does not have wireless card). I want to hook up two other laptops in the house, but can't figure out how I do that? The Comcast guy today said with an ethernet cord. So I've plugged the cord into the back of my Extreme, but the other end doesn't fit into the only slot remaining on the back of the cable modem -- which is labeled "phone"... Does anyone know how I do this?
Thanks,
Jill

You need either a router or an ethernet hub/switch between the modem and the computers to give you the needed ethernet ports. Hubs/switches are cheaper but, depending on the Comcast policy on multiple computers on one modem, may not all work at the same time.
A router, on the other hand, allows up to something like 255 devices to be connected. Instead of the Comcast server passing out IP addresses as would happen with a hub, the router issues the addresses to each device. This is useful when the ISP limits how many IP addresses can be assigned to one account (we had this with our ISP--limit of three--and is why we now use a router).
Basically, the arrangement is:
cable from wall >>> cable modem >>> router or hub >>> multiple ethernet lines out to individual computers
See if this video helps:
http://videos.howstuffworks.com/labratstv/829-episode-6-home-network-primer-vide o.htm

Similar Messages

Connect my Airport Extreme to Comcast modem

I have just ordered Comcast high speed internet service and they installed a Motorola Surfboard SB5120. They plugged it into my computer directly and I thought it was running fine. When I disconnected and tried to install it in my Apple Extreme, it doesn't work. I understand from reading some of the other topics that Comcast protects its bandwidth by not allowing routers to distribute to other computers, but can I change that?
I use 2 hard wire and 2 laptops around the house, can anyone help me configure the modem to distribute the signal?

I have an Arris TM402P cable modem that I rent from Comcast and it has a reset button on back which is accessed by pushing in with a pin or tack. This works to reset the modem without removing battery. Comcast said to disconnect modem from router or computer, hold for 10 seconds, allow to reset for 3 minutes or more, and then connect to router or directly to computer (Mac). This works fine for me and yes you can not switch from direct connection to router or back again without a hard reset such as above.
BTW, are you happy with performance of Apple AirPort Extreme Base Station with Comcast. I'm thinking of getting one since my DLink router seems to be on it's way out - 2+ years old. thanks

How do I add an airport extreme to a cable modem with only one ethernet port, while keeping that port connected to my Mac?

I have a mac pro connected by ethernet to a cable modem via ethernet. There is only one ethernet port on the modem.
I want to keep the Mac connected via ethernet for speed. Is there a way that I can add an airport extreme to this set up - for my ipad and roku, and for guests to use - or do I need to buy a router to put between the modem and the mac?
If I need a router, what kind?
Thanks.

The modem connects to the WAN "O" port on an AirPort Extreme router.
The Mac Pro connects to one of the three LAN <-> ports on the AirPort Extreme router.
Or if you do not need the ability to connect a hard drive to the USB port on the router, you can save a bit by using an AirPort Express.
The modem connects to the WAN "O" port, the Mac Pro connects to the LAN <-> port
Either the AirPort Extreme router or AirPort Express router will allow up to 50 wireless device to connect.
There are many other wireless modems offered by other manufacturers as well.

AirPort Extreme/Router/Arris Cable Modem

I have Cable internet, and I'm using an Arris Cable Modem. I got a router a while back, and it was working great between my PC and PowerBookG4, when one day it stopped working. I eventually through the router out. Yesterday, I tried connecting the Arris Cable Modem wire to my AirPort Extreme. I turned on my Powerbook, and in the little AirPort icon I had 4 bars, so I assumed I had a connection. I opened up Safari, but I couldn't get anything. I tried restarting, reconnecting, and anything else I figured would effect the connection. The lights on the AirPort express, when I connect the wire, are...1st one is blinking, but slowly, 2nd is steady, 3rd blinks. I'm wondering if theres something preventing me from using the Cable Modem w/ Airport Express.
- Thanks in advance.

Connect the cable modem to the Airport Base Station's WAN port (that's the port labelled with the "circle of dots" icon). Then pull both the modem and the Airport Base Station from power for at least five minutes. Then plug the modem into power and wait a minute. Then plug the Base Station into power and wait a minute. Then try internet access via the Base Station again.
That's my only bit of advice. No other suggestions if that fails to work.

Facetime "Fails" to connect via Airport Extreme using Comcast?

Greetings,
First time poster... tried researchings specifics on my situation and couldn't find anything so posting here to see if a solution has been found.
I used to have Verizon DSL for ISP with Airport Extreme as my wireless router. Everything worked including Facetime (only issue was the need for speed). Switched to Comcast as ISP which uses cable and had the Tech reconnect it to the Airport Extreme to behave as the wireless router. Internet is on and good... got a green light on the Airport Extreme. However, when attempting to connect via any device using Facetime (it will ring but as soon as it is answered I get "Fail" message and it ends) be it my laptop, desktop or either of our iphones I have IOS7 and IOS6 respectively same error. Did not make any modifications to Airport settings or any of my devices.
When checking the common response to this issue was a potential "Blocked Port" situation... but by digging a little deeper it appears that Comcast does not block ports that are relevant to Facetime (please confirm). I didn't see anything else that would suggest a solution at this point.
Help would be greatly appreciated as we enjoy using facetime to have our 6 month old daughter connect to our grandparents.
Thanks,
Andrew

The USB port on an AirPort Base Station other than the 802.11n model is only for use with an USB printer; hard and flash drives will not be recognized. The compatible base stations include version 5.0 of the AirPort software on a CD.
(27846)

Slow connection with Airport Extreme

Just upgraded my cable modem connection to the very high speed. 6 Mbits download, and 786 Kilobyts upload. 2 Macs connected via Airport Extreme to the cable modem. I am getting the upload speeds, but the download speeds are 2322.04, and 270.744, as an example. Troubleshooting it with the ISP (Adelphia) they say the problem is in the router. Because on a direct connection, bypassing the router I get download speeds of 5147.015, and 4129.464 as an example. They told me to update the router's software which I did to Version 5.7. That did not resolve the speed problems. I am still not doing any better on the speeds. Since the problem seems to be the Airport Extreme router, does anyone have any ideas? Thanks.

and it worked fine up until a few weeks ago
That would be the time that someone near you likely set up another wireless network that is interfering with your network. If it is any consolation, your network is likely interfering with his as well.
Unfortunately, the bottom line here is that other than experimenting, there is just not much that you can do. A good friend of mine recently moved into a new downtown condominium complex and found that his wireless was virtually unusable due to the number of other networks around him.
The only solution that worked for him was to take an older AirPort Extreme that was capable of 2.4 GHz and 5 GHz, but not both at once like the newer models, and set up the older AirPort Extreme for 5 GHz only.
ironically, the better antennas in the newer AirPorts provide better wireless coverage, but they are also more susceptible to picking up other signals that may interfere with your network. My opinion on that, based on my experience here with one of the new AirPort Extremes.
I went back to my old AirPort Extreme and while I have a bit less range, things work better.
This is the newest model, do you think the ac vs n connection would have anything to with it?
Most interference issues occur in the 2.4 GHz range, so it is very unlikely that an "ac" connection....which runs at 5 GHz....would be the cause of your issue, since there are very few 5 GHz networks....for now.

Having Trouble getting airport to connect to new comcast cable modem

Help, I'm been at this for 2 days now. I don't know why I'm having so much trouble.   I'm trying to transfer from DSL to comcast cable modem and running into lots of problems getting everything to work.
I can't get my airport extrreme to talk to my new comcast cable modem. I've tried everything, restart the modem, restart and reset the airport. chaning out cables, ensuring the green light is at the cable connection of the modem and the airport.
I can find two issues I can't resolve. one, the 10.0.0.1 webpage for the modem/router doesn't response, pings fail to 10.0.0.1. Yet, my computer is talking to the internet nicely using an ethernet cable to this cable modem. I've talked to comcast for hours, to many different people, over Many hours, and they either say the box is working or hang up on me or transfering me to nowhere land.
The airport never goes to a green front light, and airport utility and always dispay an empty IPv4 address. I've tried everything, and can't get the airport to renew it's DHCP license.
Where am I going wrong? I've search the web, and tried the solutions I found. Is my 3 year old airport too old? or is my comcast box bad? I checked the airport firmware and I'm on the latest version.
After getting this working, I still have an OOMA to transfer over to the comcast modem. Am I kidding my self? Help please.
selina

ok, answering my own question, Turns out, there are three ways to do a hard reset on my airport extreme. Only the last method worked. The easy reset, from the Airport utility menu ( clicking the restore default setting) didn't make my airport talk to the new comcast cable modem. The second way, by pressing the reset button while power up didn't work. The harder third way, hold in the reset button and then plugging in the power cord did work. and the airport is now playing nicely with cable modem.   I wasted how many hours before reading this method in the apple support pages ? and then remember doing this trick once many years ago.
I also wasted a few hours trying to get ooma to talk on the new cable modem, and the hard reset key for OOMA to play nicely with a new modem can be complicated. This method requires it to be connected and working ( plug ooma tele into the older DSL network), hook a phone to it, dial * # * # 0 9 9, (star, pound, star,pound then 099) and saying yes.    That reset it to factory settings letting it reconfigure itself to a new modem gateway.
I still can't get into the gateway web page 10.0.0.1 to change the admin password, Don't advertise that. I get no reply to request or to pings. I think some comcast rep changed a port setting so I can't reach it. So I have an open wireless connection and unprotected.
I hate switching my network provider. Now I need to write it all down, for when I get fed up with comcast and decide to move to another provider.

How do I connect my Airport Extreme to my modem (Cisco Model DPC3010)?

I am having trouble connecting my Airport Extreme Wireless Base Station to a Cisco Modem (Model DPC3010). I have used the Airport Extreme for years with other modems with no trouble. Alas, this time around I can't get it to work. I think I might not have the cable connected correctly. Help, please. Thanks

I am having trouble connecting my Airport Extreme Wireless Base Station to a Cisco Modem (Model DPC3010). I have used the Airport Extreme for years with other modems with no trouble. Alas, this time around I can't get it to work. I think I might not have the cable connected correctly. Help, please. Thanks

IBook and Comcast Cable modem--can't connect to Internet? Please help

Hello everyone!
I have an ancient iBook . Here are the stats:Mac OSX version 10.0.3(told you it was ancient), 193MB, PowerPC G3. I bought it off of eBay about two in half years ago and it didn't come with an Airport card...I only received a laptop, the original box, some cds, and the adapter. I have a Comcast cable modem and I was wondering if anyone could help me figure out how to connect my iBook with the modem. Prior to Comcast, I had Bellsouth and all I had to do was simply unplug one end from my mother's Dell and plug it into my iBook and it instantly connected. However, I can't do it with the Comcast. Can anyone tell me how? Pretty please?
iBook Mac OS X (10.0.x) PowerPC G3, 193MB

You likely need to contact Comcast to get them to help you set up the iBook for your new cable internet service. They should be able to walk you through it.
In case it may be an encryption problem, you may want to check out iFelix's post in this thread:
http://discussions.apple.com/thread.jspa?threadID=877766
Good luck.

Do I need to connect the AirPort Extreme with a ethnet cable

Do I need to connect the AirPort Extreme with a ethnet cable

Hi Tracy,
I have an airport express connected by ethernet cable to a Netgear modem which is connected to a phone socket. Those devices stay at one end of the house. I can use my MacBook Pro to connect to the internet (by Wi-Fi, no cables) anywhere else in the house. I hope this helps.
Ian.

"No Internet Connection" via AirPort Extreme bridged to Time Capsule

Hello,
We have a fairly large and odd home network consisting of a Comcast cable modem connected to a Netgear router, a Time Capsule wired to that one floor down (serving up WiFi and DHCP), and a new AirPort Extreme wired one floor below that, extending the WiFi network of the Time Capsule and set to bridge mode.
On one MacBook Pro (and possibly others, haven't had them available to test yet), trying to connect to WiFi while downstairs (i.e. to the AirPort Extreme) yields a strong wireless connection, but "no Internet connection"; checking via network diagnostics or the Network panel reveals that the MacBook Pro has no IP address. This seems odd, as it happens even if the connection is first made on the 2nd floor to the Time Capsule, where a valid IP is retrieved, and then carried downstairs; even though the same IP address should be valid, the laptop's WiFi menubar icon starts cycling again and eventually shows the "!" and reports no Internet connection. Checking the Network panel reveals no IP address via DHCP. However, if I let it sit for a minute or two, the IP address comes back (the same one!) and all is well, at least for a while.
I've tried switching to a manually-assigned static IP as a workaround, and that works perfectly well, but I'd like to get DHCP working properly if I can, for convenience's sake. Is there any reason why I should be having trouble with getting DHCP from the Time Capsule via the AirPort Extreme?

Actually, yeah, my predecessor explained that he was running DHCP on the Time Capsule instead of the Netgear because he hadn't needed DHCP prior to the adding of a WiFi point (all other nodes were on Ethernet), so it had always been turned off on the Netgear. But your suggestion makes a lot more sense, of course, so I've put the Time Capsule into bridge mode as well and started the DHCP server on the Netgear. Seems to be working with my iPhone, though that was always working okay. I won't have access to the laptop to test it until later this afternoon, but I have high hopes.
Thank you!

How do I connect my Airport Extreme to an AT

How do I connect my Airport Extreme to an AT&T U-verse Modem/Router?

Connect an Ethernet cable between the U-verse router's LAN port to the WAN (circle-of-dots) port on the AirPort Extreme Base Station (AEBS). Since you will have two routers in series, you will want to reconfigure the AEBS as a bridge. (ref: AirPort Utility > Select the AEBS > Manual Setup > Internet > Internet Connection tab > Connection Sharing = Off (Bridge Mode))

Internet connection via Airport Extreme/router thats not working, why?

I have been having problems with the internet connection via Airport Extreme which I find it a bit unusual and its still driving me nuts! This is what happened:
I have lost my internet connection last Sunday evening upon my return from a weekend away from home. The last time I have used the internet connection on my macbook was the previous Friday morning. Prior to the apparent disconnection on Sunday, I have always used my internet connection wirelessly through Airport Extreme (that is connected via ethernet cable to the NETGEAR DG834v2 ADSL modem which had worked beautifully until the problem arose on my return). This wireless internet connection allowed me to surf the internet anywhere in my home.
However, upon the successful re-connection to the internet via the modem router, I have discovered several new problems. I have tried to set up the internet connection wirelessly again but instead the following happened:
1. Router (Netgear) drops ADSL connection and cannot reconnect when connected to airport via Ethernet. (which is the case when using airport wireless).
2. Router connects to ADSL fine when computer is connected to it via Ethernet. (However, router disconnects when magsafe power adapter is taken out for some inexplicable reason!)
3. Router connects to ADSL fine when nothing is connected to the router (ie. No Ethernet connections)
4. Router connects to ADSL fine when connected to airport via Ethernet and computer is connected to airport via Ethernet.
So from the above, I cannot connect to the internet properly whether wirelessly or not so I suspect it could be faulty router or could it be airport extreme? I have asked my ISP for an explanation and all they have said is that it cannot be the mis-configuration but could be to do with the power adaptors or the way plugs are set up and suggested I take out all the power plugs (and power surge protector) out to switch everything off, the macbook, router, printer and airport extreme. However, when I have re-plugged them all back in, the problems I have described above still persists!
Would appreciate any help if anyone here recognises why this is the case and what seems to be the cause of this. If so, what should I do? Though I have written back to my ISP again yesterday for more help so im waiting to hear from them...
Thanks
u2dougal

I have been having problems with the internet connection via Airport Extreme which I find it a bit unusual and its still driving me nuts! This is what happened:
I have lost my internet connection last Sunday evening upon my return from a weekend away from home. The last time I have used the internet connection on my macbook was the previous Friday morning. Prior to the apparent disconnection on Sunday, I have always used my internet connection wirelessly through Airport Extreme (that is connected via ethernet cable to the NETGEAR DG834v2 ADSL modem which had worked beautifully until the problem arose on my return). This wireless internet connection allowed me to surf the internet anywhere in my home.
However, upon the successful re-connection to the internet via the modem router, I have discovered several new problems. I have tried to set up the internet connection wirelessly again but instead the following happened:
1. Router (Netgear) drops ADSL connection and cannot reconnect when connected to airport via Ethernet. (which is the case when using airport wireless).
2. Router connects to ADSL fine when computer is connected to it via Ethernet. (However, router disconnects when magsafe power adapter is taken out for some inexplicable reason!)
3. Router connects to ADSL fine when nothing is connected to the router (ie. No Ethernet connections)
4. Router connects to ADSL fine when connected to airport via Ethernet and computer is connected to airport via Ethernet.
So from the above, I cannot connect to the internet properly whether wirelessly or not so I suspect it could be faulty router or could it be airport extreme? I have asked my ISP for an explanation and all they have said is that it cannot be the mis-configuration but could be to do with the power adaptors or the way plugs are set up and suggested I take out all the power plugs (and power surge protector) out to switch everything off, the macbook, router, printer and airport extreme. However, when I have re-plugged them all back in, the problems I have described above still persists!
Would appreciate any help if anyone here recognises why this is the case and what seems to be the cause of this. If so, what should I do? Though I have written back to my ISP again yesterday for more help so im waiting to hear from them...
Thanks
u2dougal

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

Connecting 2 Airport Extremes wirelessly....can it be done?

Connecting 2 Airport Extremes wirelessly....can it be done?
I have 2 Airport Extremes. I'm only using 1 of them right now connected to a cable modem. It works well. I can get a wireless signal in most of the house and even outside a bit. However there are upstairs bedrooms on the other side of the house that I don't get a very strong signal on. No "big" deal really but here is what I thought.......
Can I set up my 2nd Airport Extreme to wirelessly receive the signal from the 1st (main) Airport Extreme and place the 2nd Airport Extreme close to the bedrooms with weak reception? I was thinking that the 2nd AirPort Extreme could just pickup and boost my original signal.
Is this possible? I can't find it mentioned in my Airport Manual.
If so, what is the term for this? That way I can search for information on how to configure all of this. If you have any other ideas on how this might able to work please let me know.
Thanks for your help

OK, you will need to make configuration changes to both of your Extremes.
For the main Extreme (the one connected to your modem now):
Open AirPort Utility, click Manual Setup
Click the Wireless tab under the icons
Look on the wireless setup page and make sure there is a check mark next to "Allow this network to be extended". This may be under the Options tab on the wireless page. If you have a dual band Extreme, you can only extend the main network, not the 'guest" network.
Update to save settings
For the remote Extreme, temporarily locate it near your computer so that you can configure it:
Open AirPort Utility, click Manual Setup
Click the Wireless tab
On the wireless setup page, change the Wireless Mode to "Extend a wireless network"
You will select the name of wireless network created by your main Extreme. Enter the password if needed.
Make sure there is a check mark next to "Allow wireless clients"
Update to save settings
That should do it.

Connecting my airport extreme to comcast cable modem-- AGHHH

Similar Messages

Maybe you are looking for