Connecting shutter Uniblitz to computer with rs232c
Hi everyone,
I would like to connect a shutter (Uniblitz VCM-D1) to my computer. I read in the manual that this VCM-D1 can be controlled by a an RS-232C computer serial signal COM port and which must be in the Null Modem configuration. Because I didn't have any 810RJ cable, I took a RS-232c - RJ45 cable and fixed a female-female RS232 connector in a way that I have the Null-modem configuration ( crossing 2 wires). I connected everything to the computer and turned on Measurement and Automation Explorer. After refreshing it, I didn't see any connection appearing with this VCM-D1... How can I connect this shutter to my computer? I'm sure I'm doing something wrong or there is something that I didn't understand as I'm completely new to Labview. Any help would be much appreciated. Thank you.
Fisrt, thank you Dennis for replying.
Exactly, I' m using the RS232 male port of my computer. I plugged in a female RS232 connector which is connected to a 810RJ cable with wires. These wires are connected to this 810RJ in a way to have Null Modem configuration (DTE instrument?) which is necessary according to the shutter manual (like this : http://www.rlocman.ru/i/Image/2008/03/09/4.jpg). This 810RJ is then connected to the RS232c input in the back panel of the shutter.
I don't think the port is visible in MAX or device manager because whether I connect my instrument to the pc nothing appears in both of them. I still have 4 ports COM1, COM3, COM4 and LPT1. How can I know which one is related to my instrument?
Yes I have NI VISA.
Similar Messages
-
I turned my iphone off when visiting the doctor's surgery and now it won't turn back on. It had 73% battery left and I have tried connecting it to my computer with USB but nothing happens. I have taken out and replaced the sim card too. Any suggestions
If wjosten's tip doesn't work try plugging it into a USB charger (not through your computer), wait about 30 seconds and it should come on. If it doesn't remove the cord from the phone and keep trying this. I've had this same issue and found a combination of the reset & charging cable tends to work. Sometimes it takes about 5 minutes for the phone to respond.
Best of luck. -
I have updated my iphone this evening and is has asked me to connect my phone to itunes, I connected it to a computer with itunes and it says it needs restoring? and all my images etcwill be earsed I need help as I have not backed my iphone up previously please help?
YOur phone is in recovery mode, any data that was on there is already gone, you will have to restore your phone and use whatever backup you to restore to.
-
My device is not recognised when I connect it to my computer with a USB
My ancient 4gb ipod nano (2nd gen) is no longer recognised when I connect it to my laptop with a USB. I have used troubleshooting from the apple support pages to no avail.
My ipod charges via USB when it's connected to my laptop but no data seems to be being transferred.
I would really appreciate any help on this matter.Hey there Sazzle15,
If your iPod is still not being seen by your computer when you plug it in with the USB cable, I would recommend the troublehsooting information in the following article, without knowing precisely what troubleshooting steps you had performed. Start at the "Check USB connection" section and work your way down as needed:
Apple - Support - iPod nano - iTunes Troubleshooting Assistant
Thank you for using Apple Support Communities.
All the very best,
Sterling -
Is it possible to connect to a Windows computer with Apple Remote Desktop?
Hey!
I just bought Apple's Remote Desktop program and I love it!
The only problem I have is that I can't just conncect to a Windows computer.
I need to do this!!
I saw in a screenshot in the Mac App Store that the Apple Employey had connected to a Windows computer so I thought it would work just fine.
Thanks!Should be, though I have no personal experience using it. VNC seems to be touchy with ARD, so if Vine doesn't work, you might want to try another version. Or just use Microsoft Remote Desktop Connection Client for Mac or a service such as LogMeIn; those would give you the same capabilities and probably be less fuss and bother.
Regards. -
Connecting Ipod to new computer with Music stored on a network drive
So, a client of mine purchased a new laptop, and when syncing the ipod to the new computer with songs added to the new library, it says that the sync was successful, but the songs are not synced to the ipod. It syncs the time and date, but not the music. It will still sync properly on the old laptop. The ipod has been reset to factory settings and completely blank, and the songs still will not sync. I have contacted apple, and the only thing they can suggest is that there is a conflict with the drive letters since the music is located on a virtual network drive and windows does not take virtual drives into account when assigning drive letters to divices. I have not been able to verify this, but I will be going back to do some testing in the next couple days. Any information you may have to help would be appreciated! If I think of anything else I forgot I will come back and make another post. Thanks in advance.
Custom Windows XP ProSo, a client of mine purchased a new laptop, and when syncing the ipod to the new computer with songs added to the new library, it says that the sync was successful, but the songs are not synced to the ipod. It syncs the time and date, but not the music. It will still sync properly on the old laptop. The ipod has been reset to factory settings and completely blank, and the songs still will not sync. I have contacted apple, and the only thing they can suggest is that there is a conflict with the drive letters since the music is located on a virtual network drive and windows does not take virtual drives into account when assigning drive letters to divices. I have not been able to verify this, but I will be going back to do some testing in the next couple days. Any information you may have to help would be appreciated! If I think of anything else I forgot I will come back and make another post. Thanks in advance.
Custom Windows XP Pro -
Connecting a new HP computer with Windows 7 to Airport Express.
I have an AirPort Express set up with my home network, base station is configured on my IMAC. Now I have a new HP PC with Windows 7 for work, and I'm having trouble getting it to connect to the AirPort Express.
It asks for a "Security Key", and nothing in the literature or on the hardware seems to match that. I've tried every number sent with the Airport (ethernet ID, AirPort ID) but nothing works. Can someone provide advice on how to get this to work?
thanks,
KevinIt is unlikely that the very long security "key" will solve your issue with the PC, but you never know.... it might be worth a try.
Open AirPort Utility, select the AirPort Express and click Manual Setup
Ignoring the window in the center of the screen, look way, way up to the top of the computer screen where the Help, AirPort Utility, Window, etc menus are located.
Click the Base Station menu
Click Equivalent Network Password password and your "key" will appear. -
Connected Deskjet 6940 to computer with windows 7 64 bit, duplex print will not work?
I have a Deskjet 6940 model C8970A. The Duplex printer function does not work. It will manually ask me to turn around all the pages to print on the other side. Before it would print front then back of page at a time. I have Windows 7 64 bit on the new computer.
Hi,
The Duplex Unit is disabled by default, make sure to enable the accessory as following:
Enter Control Panel > Devices and Printers
Right click the HP Deskjet 6940 icon, then click Printer Properties.
Select the Device Settings tab.
Set the Duplex Unit as Installed, click OK.
Now set Print On Both Sides as Automatically from the Printing Preferences Dialog.
Please let me know if you may still experience any issue,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution -
HP Deskjet 3520 e-All-in-One Printer. Help tells me to connect to computer with USB cable
I cannot scan anything at the moment despite the fact that I was able to do so several weeks ago. I went to the HP online support site and downloaded a scan doctor programme. It tells me that I do not have the proper scan software on my system and to download it from the HP website. It does't take me to the specific software I need but to a list of things I don't have so I downloaded all of this. I am half way through the setup process for one program and it is asking me to connect the printer/scanner to my computer using a usb cable so that "the settings of your wireless network can be communicated to the printer". I don't remember getting a usb cable with the printer but if I did I have no idea where it now is. What are the chances that finding this/buying this will actually solve my problem and is there a way to solve them without the cable? Any advise would be greatly appreciated.
Hi @translator82,
Welcome to the HP Forums!
I noticed that your HP Deskjet 3520 is telling you to connect it to the computer with a USB cable. I am happy to help you with this connection issue!
To download the software, please visit this website, HP Deskjet 3520 e-All-in-One Printer Drivers, if you are using Windows 7 or above, it is recommended to use the HP Printer Install Wizard for Windows. If you do not know the Operating System you are using, please visit this website. Whatsmyos.
In the meantime, page 33 of your printer's user guide has all the options of how to connect this printer. User Guide. For the traditional wireless setup you will need a USB printer cable. Otherwise, you can always try Wireless Direct.
Hope this helps!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping! -
I want to use an old 3 GS iPhone that is no longer in service as a phone now as just an iPod to play music. When I connect the phone to the computer with iTunes running, iTunes says it can't connect to the device because it didn't get a valid response from the device. How can I get the system to recognize the phone, and let me rename it as my iPod, instead of my phone?
As an aside, the current installed operating system on this old iPhone is 4.2.1, but that wasn't one of the selectable options in the operating system list dropdown below. Don't know if that makes any difference.Hi maddogdne,
Welcome to the Support Communities!
The article below may be able to help you with this.
Click on the link to see more details and screenshots.
Using an iPhone without a wireless service plan
http://support.apple.com/kb/ht3406
Cheers,
- Judy -
Hi everyone! I tried to install the new iOs 7 on my iphone 4, but it wasn't completed (showing error 4005). Now, my iphone is stuck on the itunes' logo with the usb cord, and I can't use my phone. And itunes doesn't detect my iphone when I connect it on my computer, so I can't put it in recovery mode or someting like that... What can I do?? I tried everything they tell me to do in the apple support but nothing seems to work. Thank you!
No problem, glad to help!
Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine. -
Working on a single computer with multiple users, I have set things up to allow each user to view and listen to the others' music libraries under the "Shared Library" function. Can you then connect an iPod touch and copy music from a shared library?
Was your wife logged into the libray at the time you tried to log in? I have had a similar problem and it was because another user was logged into the library when I attempted to. I got the permission denied banner.
-
Remote Desktop Connection Times Out With "Can't Connect" From One Specific Computer Only
This is an odd one... I manage several servers from this computer. This particular server, 2012 Essentials, won't allow for remote desktop connections to either the server or attached workstations. I can get into the server's remote web page but when I
attempt a remote desktop connection, it hangs on "Initiating remote connection..." and then times out with the error response that remote desktop can't connect. But... if I attempt the same connections from any other computer, I am able to get in
and utilize remote desktop. Does this mean that there is a certificate issue with the computer unable to connect and if so, how does one remedy this? Or is it some other issue? I've attempted everything within my technical ability to no avail. Any suggestions
are greatly appreciated.Hi,
Before going further, would you please let me know the RDC version that used in the problematic computer? Was it the same with other computers?
Please temporarily disable firewall and then check if this issue can be solved. Based on your current description, it’s hard to say the root reason of this issue.
So, I suggest that you should check relevant log files and get some clues. It will help us to narrow down and solve your issue.
Hope this helps.
Best regards,
Justin Gu -
Hiya I have the 1st generation iPod and the connect to iTunes symbol come up and I no longer have a computer is there anyway I would be able to use it
You have to find a computer with iTunes and an internet connoction and
Connect the iPod to your computer and restore via iTunes
iTunes: Restoring iOS software -
I updated my iPhone software and now it is saying that I need to connect it to iTunes. I no longer have my computer with my iTunes on it. What can I do? I really don't want to lose my data! I wouldn't have updated if I had known but there was no warning.
Restore loop (being prompted to restore again after a restore successfully completes): This issue is typically caused by out-of-date or incorrectly configured third-party security software. Please followTroubleshooting security software issues if USB troubleshooting does not resolve this issue.
Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network.
Error 50: This error (and error -50) are timeout errors. Follow the steps for errors 13 or 14 above.
Above from:
http://support.apple.com/kb/TS3694
Maybe you are looking for
-
Hi all , I want to delete a file from alocation in batch. I want to use the 'SXPG_COMMAND_EXECUTE' fm . I want to create a command in SM69 . My operating system is WINDOWS NT .Can any one tell me what COMMAND i need to use to delete a file from pc
-
My iPhone 4 will not connect to my MacBookPro. It will not charge on my MacBookPro, but it will charge on a wall socket and it will play music in a 3rd party speaker system?? This is extremely frustrating not only can I not back up my iPhone but I al
-
Why do app updates no longer show up for me in iTunes?
Please don't stop reading, because I think my issue is different from similar ones I've found posts about. For the past week or so, I've been unable to update apps through iTunes. When I click "Check for Updates," it shows "Accessing iTunes Store" at
-
System Cannot Find The Path Specified
Post Author: devteam CA Forum: .NET I have a asp.net 2.0 application running on a windows 2k3 box. I've checked the path to ensure that it is correct, and I still get the following error. I've changed the permissions on the temp directories and at
-
Installing Oracle 8i on Windows XP Home
Hi All, Has anyone been able to install 8i (8.1.7) on Windows XP Home yet ? I have gotten as far as 98% complete and then the install just hangs. I have a P4 laptop and knowing about the P4 bug I've already renamed all copies of symcjit.dll and even