Connecting the UC560 to a Two Loop Start Trunk Line
I just installed a new UC560 and am ready to convert from our old Panasonic DBS 84 system. The Panasonic is fed by 4 trunk lines that go into two RJ14 trunk connectors. so that each is a Two loop start trunk line plugged into the Panasonic. My question is do I need to modify the two lines in order to connect them to the UC560 and if so, how. If not where and how do I plug them into the UC560 and configue the incoming lines so that calls come in and go out similar to what we have now. Obviously I am new at this, so please forgive the blatant ignorance. Thanks I uplaoded the Panasonic manual if it helps.
You would terminate each line in an individual RJ11 connector, and fit them in the ports labelled FXO on the UC500.
Regarding configuration, if you are the end user, and you have no previous experience or certification, it would be much, much better that you engange a reputable consultant, or certified Cisco partner, because the UC500 is meant to administered by such a professional, and is not very user friendly.
Similar Messages
-
my dad has a apple tv device where he watches films from his ipad that is then displayed onto his tv and i was wondering if i buy one for my tv, will there be a problem with the connection and there could be complications?
You can run several AppleTVs in a house concurrently, at least 5, but this requires a reasonable network set up if it is to handle all local traffic concurrently, especially if using other devices to Airplay as it seems your dad is doing now.
Usually works but the local network will be the issue if any, assuming internet connection rates are good. -
My Ipod nano 6Th sometimes shuts down when I connect the phones, sometimes it not shuts down, but the volume and standby buttons do not work. If I not connect the phones everything works fine. But with the phones connected it goes crazy. I alredy reset, restore and nothing. If I reset and let the phones connect the up and down volumes buttons start to work. But the power/stand by button don´t. I need to disconect the phones to the power/stand by button starts to works. Anyone already have simmilar problem?
A windows error message appears saying iTunes has encountered a problem and needs to shut down.
let's get a crash log from itunes, and send it to the Apple engineers for a look.
Typically, you'll need to configure Dr. Watson on your PC in order to generate crash logs. Windows start menu -> Run. Type in "cmd". Hit return. At the prompt in the command line window that comes up, type in
drwtsn32 -i
And hit return.
This will create crash logs in Documents And Settings\All Users\Application Data\Microsoft\Dr Watson\. There'll usually be a file in here called "drwtsn32.log"
prior to collecting the itunes crash log, delete any existing crash logs in there. (we want to make sure we send the correct crash log.)
Generate the crash, collect the crash log, and and send it as an attachment to this email address.
in the email to Roy, be sure to include the following information:
- A link to the thread on Apple Discussions where the issue is being discussed
- The username you are using in the thread
- The version of iTunes you are using or trying to use
- the version of Windows you are using (mention service packs)
- A concise description of the issue you are seeing
- The exact text of the error message you are seeing -
Error starting at line 1 in command
Hi,
Here is the log from Sql developer
http://dl.dropbox.com/u/40211031/log4.txt
but when directly running the same scripts, I got no problems
Edited by: Hua Min on Mar 20, 2012 9:32 AMThis is like the OP looks like
<tt>
Error starting at line 1 in command:
i n s e r t i n t o e n t _ t i t l e v a l u e s ( ' C h i e f E x e c u t i v e s , G e n e r a l M a n a g e r s a n d L e g i s l a t o r s ' , ' C h i e f E x e c u t i v e o r M a n a g i n g D i r e c t o r ' )
Error report:
Unknown Command
Error starting at line 2 in command:
Error report:
Unknown Command
Error starting at line 3 in command:
i n s e r t i n t o e n t _ t i t l e v a l u e s ( ' C h i e f E x e c u t i v e s , G e n e r a l M a n a g e r s a n d L e g i s l a t o r s ' , ' C o r p o r a t e G e n e r a l M a n a g e r ' )
Error report:
Unknown Command
</tt>
Regards
Etbin
Edited by: Etbin on 19.3.2012 20:30
Maybe multibyte character set related (a SQL Developer malfunction ?) -
I do not know what the error is. I have googled it but I can not find anything. Help me please!
"An unknown error occurred (-42110)". The message pops up then I start running iTunes. I have two devices connected to iTunes. 1) iPod touch 3rd gen 2) Apple TV. Help me please please!Try the following user tip:
iTunes for Windows 11.0.2.25 and 11.0.2.26: "Unknown error -42110" messages when launching iTunes -
Currently I have two iPads connected to the same apple iPad. One is connected to game center(iPad air) one the other(iPad 2) is not connected to Game Center. How can I connect the iPad 2 Clash of Clan progress to game center when I already have another clash from iPad air connected?
You cannot transfer content between two accounts. The sooner you make the conversion, the better. Just pick the new one and start using it(buying music etc).
*A lot of people open new accounts when their email changes or they have a new email. You can just access your apple id account and change the primary email that you use to log in along with other details. -
When I connect the iphone does not start automatically Itunes Please help me
when I connect the iphone does not start automatically Itunes
Please help me
How to solve this problem that I havei've had a few issues like this.
I've found that it is an issue with items that are already on your phone.
several troubleshoots.
1) uncheck everything from syncing (apps, music, tv shows, movies, podcasts, etc), try to perform a sync, it most likely will work. Then, sync after checking each item individually (check the sync box for videos, then sync, check the sync box for podcasts, then sync, check the sync box for music, then sync, etc). One of two things will happen, 1) you will fix the problem, or 2) you will identify exactly what part of the sync setup is the culprit.
2) if the above doesn't work, I've found that it is likely an issue with files that are on your phone but your phone doesn't exaclty recognize (for example, I had copies of music on my phone that didn't show up in the music app, I went in on itunes and manually deleted those songs from my phone and that fixed the sync). to do this, check the "manually manage music and videos" box at the bottom of "summary" while your phone is connected to itunes. Then, go to the left hand pane in itunes and find your iphone device, click the drop-down arrow that shows all the categories for media on your iphone. Go to the music category in your iphone on itunes and delete all the music that shows up. Try to perform a sync - it likely will work. After this, you can uncheck the manually manage music box and re-sync your phone as normal
let me know if either works -
my ipad is on an infinite loop. I used ios7 for a few days and then did updates on some of my apps. that's when the infinite loop started. I have tried pressing the power and home button at the same time, but it doesn't work. Please help!
I even tried some hints posted for ios6 (turn off Ipad, holding home button and plugging in power cord at the same time and then releasing the home button)
I did manage to get a different screen that shows the itunes icon and a power cord, but nothing happens.You were on the right track. You got the connect to iTunes screen and you ended to use iTujes to restore your iPad. Try recovery mode again.
Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad. -
I am trying to update a 4s. The update did not work for some reason. Now I need to restore the iPhone. When I connect the usb to the computer and phone it says I need to restore. So, I click to restore. It starts extracting the software. But I am continually getting the same error message that it cannot complete for unknown error. I have been working on this for 5 and a half hours. I'm tired, mu husband needs his phone and apple support is a joke and of course I can't find any answers anywhere. Please help!
Hi MB2751,
As an iPhone user myself, I know it must be very much a problem to have the phone out of service because of an error such as you are seeing. Let's see if we can get you back up and running.
I would suggest that you troubleshoot using the steps in this article -
If you can't update or restore your iPhone, iPad, or iPod touch
Thanks for using Apple Support Communities.
Best,
Brett L -
when connecting the iphone to the pc to upgrade my OS itunes says "the iphone cannot be used because the Apple Mobile Device is not started" can someone help me please
http://support.apple.com/kb/ts1567
-
I have limited space on my new ipad. How can I limit the number of songs from my itunes on my imac from going to my ipad when I connect the two?
you can do this by keeping the external hard drive connected and doing the following
-hold shift key down on computer while opening iTunes and a prompt will appear to choose a library
-select choose library, iTunes should bring up your explorer windows where you can search for the external HD
-after you find the external HD find the iTunes folder you just copied to it
-after opening the iTunes folder look for the file that says iTunes library.itl or if you can't see that extenstion just look for a document looking thing in the iTunes folder that shows up as a database file
-double click the database file and boom iTunes should load your library without having to copy it to the computer
PS: do make sure that if you are going to do it this way, make sure that the external HD is connected at all times, because if you don't then you will get exclamation marks next to your iTunes songs
double PS: if you are unsure how to find out if the iTunes library file is a database file just right click it and choose properties and under the type it should say database file
hope this helps:) -
I have two different iPods. How do I connect the new one to iTunes?
I now have two iPods - a 30GB iPod I purchased about a year and a half ago which plays music, Audible books, and has photos slide show capability plus color screen. Yesterday I collected enough credit card points to afford the new 5th Generation iPod. Yeah, I'm an iPod addict. I wanted the video capability. So now I have it. My question is:
Do I have to download iTunes again, or can I connect my new iPod to the iTunes that I have been using for my other iPod? I can't find the answer to this question anywhere. Also:
Can I connect the new iPod on the same computer as my old iPod is connected on without getting confusion on the iTunes site and on the iPod?
Dell Dimension Windows XPYa, you can simply connect it to your current iTunes and go. More info here...
How to use multiple iPods with one computer
http://docs.info.apple.com/article.html?artnum=300432
Using iPod with multiple computers
http://docs.info.apple.com/article.html?artnum=61675
Managing content manually on iPod
http://docs.info.apple.com/article.html?artnum=61148
iPod: Frequently Asked Questions
http://docs.info.apple.com/article.html?artnum=60920
Patrick -
The system I am trying to create calculates a number of values based on an input. I need to make the calculations and display the values for an entire production run and for each hour. The only way I know to do this is to create two while loops, one looking at all the values that are received and one looking only at the values for hour long periods.
Any help would be great.
Thanks
RossHWhy do you think that you have to have two loops to accomplish this task? Why not use one loop and accumulate the same data into two data sets based on the two sets of criteria?
-
Help me please someone...In the middle of auditioning loops within a project, all my loops started sounding all wobbly like they are out of phase or something. what can i do to fix this. Thanks
raise your I/O buffer and raise your Process Buffer Range.
Logic Pro>Preferences>Audio>Devices>Coreaudio -
I just bought a new laptop and my ipod nano will not stay connected to my computer. When I first connect the ipod it starts to sync on my ipod but not on itunes. The ipod is initially connected to my computer, I can see it when I look on devices in my computer. However, when it finishes syncing it is no longer detected to my computer. I cannot transfer any of my songs to my new laptop because of this. I have tried to reinstall itunes, reset my ipod and use a different port. None of these things worked. Any ideas?
rubicon53 wrote:
I just bought a new laptop and my ipod nano will not stay connected to my computer.
I cannot transfer any of my songs to my new laptop
How to use your iPod to move your music to a new computer
Maybe you are looking for
-
Receiving calls while in text screen
I have a Curve, and if I am reading or writing a text in SMS the phone will not ring to notify me of a call, nor will it indicate "missed call." If I am reading or composing an email, an incoming call interrrupts and I can choose either answer or ig
-
Hai Friends, Greetings. I need to add one text box or small variable window in the standard transaction VL01N,, for this any User Exit or Customer Exits are there? IF its avaial means pls help me to guide me the step by step procedures.... Please its
-
Addition to my earlier post on TV shows on Ipod, I have noticed lately, when I sync my Ipod, some of the files listed under TV shows, disappear from the Ipod, although they are still in Itunes, and NOT selected for deletion. Is this an extra feature
-
When I move my keynote presentations from my imac to my iPad they don't work
when I move my keynote presentations from my imac to my iPad they don't work builds and movies don't work
-
HT1349 When I click on a help subject the screen that appears is frequently blank.
When I click on a help subject the screen that appears is frequently blank.