Connecting Time Capsule to a Windows 7 PC via Ethernet

Hi,
I have the following network configuration:
- Speedport (Deutsche Telekom AG) as DSL Router (I need that router for the IPTV)
- Connected to this router are two laptops and the Time capsule (WLAN)
Everything is working fine. However, I try now for days to connect my Windows 7 PC via Ethernet to this network via the Time Capsule. Due to location it is not possible to connect the Windows 7 PC directly to DSL Router or to connect the Time Capsule by cable to the router.
I think I tried every possible configuariton but without any improvements. Does anyone have an Idea what I can do ???
Windows is always telling "no identified network" and it always shows a park bench
Hope anyone have an idea ! Thanx for your help
TC - Firmware: 7.4.2

try http://www.microsoft.com/mac/remote-desktop-client
Allan

Similar Messages

Connecting time capsule to wireless modem router via ethernet cable

Hi
I use my TC to store all my data and itunes music/media. I've noticed that when purchasing music, the download speeds are quite slow, even though when I test the broadband speed, it's at a reletively ok 5 mbps. If I hard wire the tc to the modem router, will the downloads be faster? If so, how do I connect them up with ethernet cable. I've done so, and nothing seems to appearing on my desktop.
cheers
Mark.

Reset the TC to factory settings. This will allow you to reconfigure the TC to use Ethernet.

I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages sometimes. How do I fix?

I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages (no connection) sometimes when trying to connect devices to the wireless network. How do I fix? Sometimes devices cannot connect to the network because of conflicting IPs. I look on the Motorola and every device has a unique IP assigned but occasionally a device has taken the IP of another device. I have been writing down all the devices and the IPs they have been using. It happens more with PCs than Macs, ipads or iPhones.

If the Time Capsule is set up correctly in bridge mode, then it is the responsibility of the Motorola modem/router to provide the correct IP address assignments for all devices on the network.
Check to insure that the Time Capsule is correctly set up to operate in bridge mode as follows:
On your Mac, open AirPort Utility
Finder > Applications > Utilities > AirPort Utility
Click on the Time Capsule icon, then click Edit in the smaller window that appears
Click the Network tab at the top of the next window
Insure that the setting for Router Mode is configured to read "Off (Bridge Mode)"
Once you have confirmed that the Time Capsule is configured correctly, everything else is the responsibility of the Motorola modem/router as far as network routing and IP address assignments for devices.
If you continue to have IP address issues, then you should contact the Internet Service Provider (ISP) that provided the Motorola device to you and ask them to fix the issue.

Time Capsule to Extreme to Express via Ethernet Connection ?

Recently purchased all three to help simplify my Home/Business network but having issues connecting and communicating between all three.
Whole home is hard wired for ethernet in every room so I assume this would be the fastest method of linking all three together but would also like all three to broadcast wireless for full property coverage. I beleive I am using airport utility 5.6.1 for setup. I am working on Windows 7 machine.
Setup so far is:
Motorola Cable Modem with Charter Service to Wan Port of Time capsule (Seems to all work well)
Then in other room/level Airport Extreme with ethernet from time capsule to Wan Port of Extreme
and this is the point where I lose it... I haven't even gotten to the Express on the basement level..
Could anyone chime in with more understandable instruction on both hard wire configuration and software using
airport utility?
Or maybe point in right direction? What other info needed?
Certainly appreciate any help..

The roaming document explains adequately how to setup... at least the principle of it.
It isn't hard at all..
One device is the main router.. You create a wireless network from this router.
All other devices are bridged.. (that is router bridge not wireless bridge)
They all get IP address from the main router.
All of them create a wireless network..
if you want roaming you simply use the same name SSID (wireless name in apple speak).. same security setting WPA2 Personal = WPA2 AES and password.
But you can setup different networks if you want.
Channels are supposed to sort themselves out automagically.. but I don't believe in voodoo.. try voodoo first and if it fails, no biggie.. set manual wireless channels.. set simple short names no spaces pure alphanumeric.
It is perhaps new for you and the lack of html setup is a pain.. but it isn't hard to do. Apple have cut back the number of options to barest min to do the job.
Come back and ask specific questions if you run into trouble. We have some very clued up people here.. who spend their life energy answering the same question every day with a cheerful attitude.. never seen the like.. on a windows forum you would be told to RTFM.

Connect Time Capsule with Samsung LED TV via LAN - will it work?

Hi. I am from Germany and my englisch is very bad. Sorry for that.
I want to by a Time Capsual and a Samsung LED TV with LAN integrated.
I want to connect the Time Capsual via LAN to the TV to watch Movies, listen Musik and watch Pictures. I have not found any informations, if that will work.
I hope you understand my question and somebody can help me. Thanks

narfist wrote:
Hi. I am from Germany and my englisch is very bad. Sorry for that.
hi narfist and welcome to the discussion area !
I want to connect the Time Capsual via LAN to the TV to watch Movies, listen Musik and watch Pictures. I have not found any informations, if that will work.
it will not !
consider getting an Apple TV. you can store content locally on the ATV or you can keep your iTunes media folder on the time capsule but would need iTunes to be running on your Mac to stream content to the TV (via Apple TV).
good computing

Use Time Capsule as a Hard Drive via Ethernet for Time Machine

Hi Folks
To summarise a very very long story here goes;
- About 12 months ago my father in law buys a Time Capsule without really knowing what it is for and how it works (I know don't ask!!!!!)
- I set it up for him connected to his wireless router so he uses his router to access the internet and uses the Time Capsule to back up his iMac via wireless with Time Machine. (from what I can see he could have saved himself some cash and just bought an external Hard Drive and connect it via USB to the iMac for Time Machine, but never mind. He has 1 iMac and no other Mac's in the household. His printer is connected to his iMac via USB in the same room and he uses a wireless router to access the internet, since the phone point is in another room)
- All is well until Monday when he tells me he cannot access the internet. After much much trial and error I have eventually managed to get his internet back up and running, but he has somehow managed to erase his Time Capsule.
- I set his Time Capsule back up as it was previously and it starts performing the initial backup again. However at the rate its taking I think it will take well in excess of 24hrs to do that initial
backup. Also so far It has failed 3 times during this initial backup and I get an error message stating it's failed. The setup guide makes reference to performing the initial backup via ethernet as it's quicker.
I'm thinking the best way forward would be to just plug the Time Capsule into the iMac via ethernet and use it purely as a Hard Drive for use with Time Machine. I've tried just plugging in the ethernet cable from the Time Capsule to the iMac, but it doesn't recognise it. Bear in mind that it currently works via wireless, do I need to perform some sort of factory reset or how do I go about telling the the iMac to no longer use the Time Capsule wireless, but just connect via ethernet instead.
Of course I could just forget about the Time Capsule all together and tell him to get a 500gb USB External Hard Drive, plug that in and set up Time Machine with that instead.
Am I missing the point here and can the Time Capsule do a lot more for him, given his current setup.
Thanks

That is true but if you mix your files with the Time Machine backups, Time Machine will have trouble contril disk space when it gets low.
If you are going to do that it is recommended that you partition the drive. Since Time Capsule is not able to partition the drive that means you will have to remove it in order to partition it.
A simple solution IMO is to get another external drive and hang it on the USB bus in the Time Capasule.
Allan

Time Capsule vs. Airport Express via Ethernet

Air;ort Express is connected to a DSL modem with an Ethernet cable. Time Machine is in turn connected directly to my MacBook Pro, again by Ethernet. Obviously something here is wrong, since the Time Machine persist in showing a blinking yellow light.
I think that this used to work but no longer. How did I sdrew up?

Does that in turn suggest that I should connect the Time Capsule directly to Airport Express?
when possible always run ethernet.. it is fast and reliable.. only when there is no other choice use wireless to link routers.. it is always poor.
You can use wireless from laptop to the Express or the TC.. that is fine.. but keep the wireless usage to something close and just once.. no double hop over wireless.
If you have ethernet there, use it.
Simply put the TC in bridge mode.. that is router bridge.
And make sure you are creating a wireless network on the TC.. same name and same security setting and password as the Express.. then the laptop can connect to whichever it is nearest to.
If you need complete diagrams or screenshots just ask.
life is a lot more complicated than it was when I bought my first 128K Mac in 1984.
Not always.. networking with modems and telephone wires was not always fun.. !!
You forget what it was like 30years ago.. !!
I started about that time but could never afford Macs. When I think of all the money I spent on computer gear over the years it is frightening.
Instructions here for roaming network since Apple has none up to date.
Setting Up Roaming - New AirPort Extremes and Utility

Connecting Time Capsule with WildBlue Satellite Service

HELP! Please...
I am trying to set up Time Capsule to work with my satellite service, WildBlue, and I can't get it working properly.
Before WildBlue was installed, I connected my iMac and my wife's iMac (it's on Mac OS 10.5.0), one at a time, with Time Capsule directly via Ethernet and back-up each iMac.
WildBlue satellite service was installed yesterday and the installer had no idea how to hook everything up. It was his first install. I was able to connect the WildBlue modem via Ethernet directly to my wife's Mac and made it work. When I try to add the Time Capsule, that's where I run into problems.
I ran the Ethernet cable from the WildBlue modem to the Internet WAN port on Time Capsule and I could not get it to work at all via AirPort. I tried using AirPort Utility and System Preferences - Network and could not get anything to work. I then ran an Ethernet cable from one of the four Ethernet plugs on the back of Time Capsule to the Ethernet plug on the back of my wife's iMac and was able to connect to the internet and get email on her Mac. I tried to run Time Machine, but it can't find Time Capsule! The only way it seems that I can get her iMac to do anything is to either connect it directly to the modem without Time Capsule or run the Ethernet cable thru Time Capsule to the iMac and not be able to connect to Time Machine. I still could not connect my iMac (it's on Mac OS 10.5.4) via Airport no matter what I did.
Can someone help me so that I can get Time Capsule connected and working the way it should?
My understanding is that I should be able to connect Time Capsule to the WildBlue modem via Ethernet and then connect my wife's iMac directly to Time Capsule via Ethernet and still be able to run Time Machine to back-up her iMac. Her iMac and the WildBlue modem sit in the same room together and my iMac is on the other side of the house where I want to use AirPort to connect to Time Capsule so that I can back-up my iMac and have access to the internet. If this isn't the way it is going to work can someone explain it to me on how it should and how I should set everything up to work correctly?
Thank you in advance for any help you can provide me.
Rod

You can, but devices connected to the D-Link switch will drop to a maximum of 100 Mbps speeds. The Time Capsule supports 1,000 Mbps or Gigabit speeds.
If you plan to transfer a lot of files using Ethernet, the numbers speak for themselves.

HT1941 trying to connect time apsule to macbook air with the ethernet cable in the WAN port the airport utility doesn't detect it

trying to connect time capsule to macbook air with the ethernet cable in the WAN port but the airport utility doesn't detect it but when i put it in the LAN one it does but it doesn't let me configure
any ideas?

Isn't it fun trying to do things without an ethernet cable direct to the computer.. Apple sell a usb to ethernet adapter cable fairly cheap.. makes life a lot easier having something to do hard connections.. or as hard as usb can manage.
Since you have to access the TC by wireless .. press and hold the reset button on the TC for about 10sec until front led flashes rapidly.. don't worry about the ethernet cable.. leave it disconnected.
Now click on the airport symbol and join another network. The TC should revert to its home name.. which will be a combo of Time Capsule and its MAC address. There is no wireless security and you can do the setup.

HT1175 I am trying to setup my Time capsule via a ethernet cable as a back up for a new iMac. The on button on the time capsule set up window keeps failing to stay on. Any ideas what to do?

I am trying to setup my Time capsule via a ethernet cable as a back up for a new iMac. The on button on the time capsule set up window keeps failing to stay on. Any ideas what to do?

A PC can have more issues connecting than a Mac.
But it really should not matter.. so just try it in situ.. press and hold the reset.. once it starts up, it will return to default IP, 10.0.1.1 the PC should then be able to find it via the airport utility.
If not drag it over to the Mac and plug in there by ethernet.. or since it is a laptop, really should not be that difficult to drag the Laptop and plug it into the TC.
Important thing is to get access to the TC.
The Mac if it is running lion, then you MUST download and install 5.6 airport utility to do anything useful.
http://support.apple.com/kb/DL1482

I receive a not connected to the internet message several times daily on my iMac connected via airport to a time capsule which accesses the internet via cable modem.. When I input my password to enter network preferences, the connection re-establishes.

I receive a "not connected to the internet message" several times daily on my iMac connected via airport to a time capsule which accesses the internet via a cable modem. Software/firmware is up to date on the iMac (OSX 10.6.8) and Tme Capsule(7.5.2). Browser is Safari 5.1.
When I input my password at the prompt to enter network preferences, all the lights go green (ie... ethernet, ISP etc.) and the connection re-establishes immediately and states "the connection appears to be working normally".
It more of a nuisance than anything and seems to have started ocurring over the past couple of months. I also have a windows XP box also connected to the same cable modem that I never have internet connectivity issues with. I've verified all the physical aspects of the connections and can't see any evidence of any actual drops in the modem logs. I suspect it is just an intermittent communication loss between the Imac and the Time Capsule, but I am not very familiar with Mac equipment yet.
Just wondering if anyone has experienced a similar problem and what you did (if anything) to resolve it?
Thanks.

The AirPort Express will connect to your existing wireless network if the network is using WPA2 Personal or WPA/WPA2 Personal wireless security settings.
So, it can join the network as a client and then provide an Ethernet signal to your Time Capsule.
Be sure to configure the Time Capsule to operate in Bridge Mode so that it will be operating on the same network.

TS2706 I cannot connect to my airport (time capsule) from a Windows PC

Any information on how to connect to an aiport extreme (really the time capsule) from a Windows platform. Have no problem from our Mac's but cannot connect from a windows based platform. I haven't been able to find any recent posts to help with this problem.

First off, Archon23, what you want to achieve is possible. I have access to both my Time Capsule (TC) and the USB drive connected to it, from a Win. 7 and Win. XP machine.
Here is what I see from the Windows side of things:
     From My Computer - TC USB Drive (Y)
     From Windows HomeNet - Time Capsule:
Now getting there is the trick.
One caveat before proceeding: I am not well versed in Windows Networks, Windows Sharing and Firewall settings so some of the following may not be elegant, may not be absolutely required, and may not be the best way of getting there. But it is what I did to see both the TC drive and it's attached USB drive on the Windows side of my network..
1.) First, I added Airport Utility to the Inbound rules of Win 7 Firewall
While poking around my Network Sharing and Firewall settings trying to figure this out, I got a Pop-up recommending I do that. AND I did that. Oh, and while you are at it, make sure you have a Home network established.
2.) Next, on a hunch, I installed a USB Wi-Fi Adapter (under $20) to my Win PC, enabled that Wi-Fi connection and disabled my Ethernet connection. I was getting no where on this matter with my Ethernet connection to a DSL Gateway. But with a Wi-Fi connection to my AirPort Express Base Station, I made progress.
3.) Finally, while poking around my Network Sharing Center some more, one by one I started the various network device Setup Wizards in there, and Trouble Shooters, to find the elusive TC/USB devices in question...AND voila, it worked.   And it's stable, been this way for going on two weeks now.
Good luck.

How do I connect to Time Capsule from a Windows 8.1 machine which is on a Windows domain. I have been able to connect from a Windows 7 machine on a Windows domain to a Time Capsule. Airport utility is not displaying the Time Capsule Win8.1 machine

How do I connect to Time Capsule from a Windows 8.1 machine which is on a Windows domain. I have been able to connect from a Windows 7 machine on a Windows domain to a Time Capsule. Airport utility is not displaying the Time Capsule Win8.1 machine.
I have checked that the firmware has been updated to 7.6.4 . Similalrly the Win8.1 machine has been loaded with the update specified in another discussion.

Firstly how are you connecting to the TC.. wireless or ethernet?
Please open a command window and ping it.. ping by name and by IP address.
If ping succeeds at least by IP it should work.
In windows explorer type
\\10.0.1.1 (or whatever the TC ip is.. that is the default).
Having the airport utility for windows loaded can help the process. As it loads bonjour for windows.
7.6.4 firmware on the TC is useless. It works better on 7.6.1
If the ping does not succeed by either name or IP address yet you have internet through the TC, then your network is setup wrongly. You are have firewalls blocking local IP. Take down all the firewalls.

I have a modem from my cable company that provides WiFi. When I try to connect time capsule to the modem via an ethernet cable I am unable to and I also lose my wifi connection

I have a modem from my cable company that provides WiFi as well as ethernet ports for internet TV and Sonos. But when I connect Time Capsule via an ethernet cable to the back of the modem I am unable to get it to work and I lose my wifi connection completely. I added Time Capsule to back up data and also to extend the reach of my wifi with an airport extreme hooked up by another computer.

Put the TC in bridge before you plug it in.. ie do the setup in isolation to the rest of the network..
I would also start a new wireless name on the TC so it is different to the cable router..
If you want to be exacting also set wireless channels so the cable router is set to say channel 1 and the TC set to 11 for 2.4ghz. Then plug it in.. you will have no trouble as the TC will get an ip address as part of the existing networking.. then extend the wireless using the extreme.

Connect time capsule via ethernet to Mac for back-up only. Is it possible without internet connection ?

Connect time capsule via ethernet to Mac for back-up only. Is it possible without internet connection ?

Hi Bob,
I'm not certain the post I sent was posted correctly, as I added it as a reply to a 3-year old thread. Since this is a recently-active thread, though not specific to the issue at hand, I thought I'd post again:
Three years ago you helped me set up a roaming wireless network in my home. It's been rock-steady and I'm forever grateful to you for the time and guidance you gave me. I'd now like to swap out my AirPort Extreme base station for a time capsule. As I understand it, I should be able to unplug the base station and replace it with the TC without problem, so long as I use all the same settings on my TC... network name, security protocol, password, etc. Given the complexity of my network, I thought I should check with you first for any advice you might have. I don't want to set up a new network or make any changes to the existing one-- with the exception of using the TC in place of the AE. I'm already using Time Machine for backups. As a refresher, my current setup has the AE as base station and 3 expresses hard-wired with Ethernet connections elsewhere in my home. I have a 4th express set up wirelessly to use with my stereo system at the front of the house. All AXs are 'n's and are set up, as per your instructions, in Bridge mode to extend the existing network. I'm running the most updated version of Mavericks on my MBPro. Any suggestions you might have will be, as always, very much appreciated! Sincerely, Phyllis Sommers

Connecting Time Capsule to a Windows 7 PC via Ethernet

Similar Messages

Maybe you are looking for