Connecting time capsule wirelessly to BT home hub

Help unable to set up time capsule to wirelessly join my BT home hub (original white home hub for use in UK). Goes through all the stages then when restarts can't find airport device. Took it to local genius bar and worked fine there. Is this a problem peculiar to home hubs?

ESM@ESM, welcome to the discussion area!
In order to "Join a wireless network", you need to know the exact type of wireless security that your BT Home Hub is using, so you can provide those settings to the Time Capsule. It cannot join your network unless you have the correct settings.
It would be much easier to configure your Time Capsule to connect to your Home Hub using an ethernet cable. This will still allow you to use your Home Hub wireless network for backups, and you'll also have the option to use ethernet for backups, which will allow you to backup much more quickly. Can you consider that option?

Similar Messages

I am unable to set up my new Time Capsule with my BT Home Hub - every time i connect the ethernet cable from Wan port to Home Hub, the internet signal drops

Hi there -
I've just purchased a new Time Capsule, and would like to set up a small home network with my Laptop, iMac and wireless printer. I'm following the first steps, but as soon as I connect an ethernet cable between the WAN port of the TC and the ethernet port of the HH, my BT internet connection drops out and I have to restart the HH. Upon which point it drops out again. The airport utility can see my TC, and gets as far as me typing in the new network name and setting up a password, but then it can't quite get through to the next stage. All the time it's just flashing amber.
Please help!

Setup the TC in bridge mode before you cannot it to the HH.
Simply do the setup fully in isolation. And do it by ethernet.
Setup wireless to create a wireless network.
You can use either same SSID =Wireless name as the HH .. same security same password.
Or use a different name and setup.. totally up to you.
Update the TC and then plug it into the HH by ethernet.

Do i connect the time capsule to my bt home hub

I thought that this would be simple, but here I am 2 days later. I have a BT home hub, which I have used a powerline network to extend connection to the other end of the house. I wanted to plug the TC into the output of the powerline, but this did not seem to work, after lots of turning routes on and off. Today tried to wire it directly to the home hub, still no luck. I am not that technical, so any help is greatly appriciated. Thanks in advance.

thank you for the response, yes it was. Also a couple of things, the IPv4 is there, but all the fields around router address are empty. My TC also says that there are 4 warnings, ethernet, internet, and a couple of updates.
I can not see any lights flashing on the ethernet port
thanks

Time capsule with a BT home hub

hello
i have a time capsule that connects to by BT home hub 2 wireless and while doing a backup it drops the connection to the hub and the router has to be reset- can anyone help me with this problem
cheers steve

I had an initial rejection message like you connecting to BT Hub, Mark.
I used the setup to add to my existing network (BT Hub) and the amber light on the front of the capsule just kept flashing, looking for a network. This was done wirelessly
So, I reset the capsule to factory settings by pressing the reset button on the back for 5 seconds amber flashes fast. I then restarted my computer and restarted the BT Hub
I then ran airport utility again. (No ethernet cable is connected, but running wirelessly) When the Time capsule appears in the left sidebar of airport utility and the IP address is picked up in the main window, I then clicked on continue. After naming the capsule and giving it a password, I then clicked on continue. When I got to the next window, I choose the top one 'I have a wireless network and want to add Time Capsule or replace an existing device on my network'
I then clicked continue and in the next window I chose the second option 'I want Time capsule to wirelessly join my current network'
In the next following window, your BT Hb will show in the first field, click on wireless security (I chose (WEP 40 BIT preset) and enter your BT Hub wireless key and repeat it into the next field.
Clicking next will give a summary of what the settings will be updated too.
When the final window appears, close it and wait for the steady green light appears at the frot of the capsule. Be patient and it will work.
If you go by the settings similar to mine you should be good to go.

Will the time capsule work the bt home hub 3

Will my time capsule work with the bt home hub 3

Apple products work in a huddle with themselves.. all others are excluded so no you cannot wireless repeat if that is what you mean.
In bridge though the TC can work as a WAP.. as can every wireless router ever made. You must connect to the home hub by ethernet. Then set the wireless manually and use the same network name, ie SSID, and security settings and password.. but you need to use a different wireless channel. You can then roam with any wireless devices..and they should connect to the strongest signal. In reality it doesn't work 100% and I think it is easier to use a different SSID and know what you are connecting too, but that is up to you.

Binned BT and want to use Time Capsule instead of BT Home Hub

This is my first question so please be gentle with me and forgive any errors!
After a truly horrendous experience with BT (22 calls to them in two weeks to resolve broadband speed of 0.4 mbps and no that's not a typo) I've changed ISP.
I already had a Time Capsule which previously I've used only as back up facility. Now I have a separate cable modem and want to use the Time Capsule as a router. The cable modem is plugged in to the phone line (with a filter) and there's an ethernet cable connecting it to the Time Capsule.
I thought I could bin my hated BT Home Hub, but the minute I unplug it, the set up doesn't work.
So it would seem that my Mac is talking to the Home Hub, that's talking to the TC and that's how I'm getting onto the net. I'm at a loss what I need to do to be able to throw the Home Hub in a skip.
Would greatly appreciate any advice as this is frying my tiny brain!
Thanks in advance.
Macbook Pro, iPad 2, iPhone 4, Time Capsule

There are some issues here.. if your modem is plugged into the phone line it is adsl not cable modem..
The TC is not a modem.. it is a router.. you still need a modem to provide connection. Ask your new ISP for what their preferred modem is.. In the UK most ISP use PPPoA method of authenticaiton.. The TC cannot handle that.. they only offer dhcp to an existing router or PPPoE. That means the TC needs to be bridged. If the BT home hub is now running fast though, a new modem is not going to make the connection go faster.

Connecting with a Wireless Printer on Home Hub 3.

How do I get a XP Notebook to connect with the HP Photosmart 6510 connected wirelessly to my BT Home Hub 3.
My Network Places shows BT Home Hub 3.
Double click on HH3 and scrolling down to My Home Network.
You can see HPFE0AAB under wireless network, which is the HP Photosmart 6510.
According to the Photosmart it’s url is 192.168.7.71 and it is correctly connected to the hub.
The XP Notebook does have the relevant basic printing drivers installed for the Photosmart.
Perhaps I should add that I gave up trying to connect the Windows 8 Desktop to the printer wirelessly and used a USB instead. I’m not sure if the problem is with the set up of the Notebook or the Hub. I have tried turning off firewalls which so far seems to make no difference. I am running MSE on the Notebook and Defender on the Desk Top.
I've tried so many approaches I'mgoing round in circles.
Solved!
Go to Solution.

Here are the GENERAL steps on how to add a wireless printer on your wireless network.
As you have said that it is already connected and visible to the network it is a case of checking the settings below then if ok go to “adding printer to your networked computer” section
The wireless printer must have a static (i.e., manual) IP address assigned to it from your network IP address range. It cannot be DHCP enabled, otherwise every time DHCP assigns a new address, your printer port will stop working.
How to set a manual IP address on your printer:
When the printer is connected to the network the first time, the router will assign an IP address to it. To get the IP address that the printer was assigned, find the printer on your network and right click on it. It will bring up a properties box. The IP address for the printer will be found somewhere in there.
Using an Internet browser, type the IP address of the printer into the address line of the browser and press enter. It should bring up a printer configuration window.
Now, since each printer is different, I can't give you the exact steps, HOWEVER, here's what you are looking for:
Find a Network - TCP/IP configuration menu. Somewhere in that menu, it will give you the choice of setting a manual or static IP address versus a DHCP (Dynamic Host Control Protocol) assigned address.
You want to manually set the IP address to the address given on the configuration page. This would normally be 192.168.1.xx. The subnet mask will normally be 255.255.255.0 and the gateway will normally be the IP of the router, usually 192.168.1.254
Once the IP address is assigned permanently to the printer as a static address, you are now ready to add the printer to each computer on your network.
Add the Printer to Your Networked Computers
In Windows XP, follow these steps to add the wireless printer to your computer:
Go to Start, Printers and Faxes.
Double click on Add Printer
Click Next.
On the Local or Network Printer dialog box, choose Local Printer and UNCHECK the box that says "Automatically detect" the printer. Click Next.
On the Select a Printer Port window, choose to Create a New Port, and then under Type of Port, choose Standard TCP/IP port. Click Next.
Make sure the printer is On and Ready, and connected to the network. Click Next.
Type in the static IP address of the printer that you set in the steps above. Click Next.
It will then try to connect to that IP address. It you typed it wrong, or the printer is off, it will come back and give you an error.
If all is well, it should then ask you for the printer driver. Either set it to find the driver that you have previously installed or insert the CD for the printer, and find the Windows XP version of the driver.
Then choose the driver you want to install.
Click Next. It will install the driver and ask you to name the printer.
When it is done, click Finish. (You can choose to print a test page if you want).
Hope this helps.

How to connect Time Capsule wirelessly (without hard wire connection)

Okay, so just bought a Time Capsule, and in the process of setting it up, I am being told by Airport Utility that I need to hardwire the TC to my wireless router in order for it create a network.....
My question: Is there anyway around this? Is there anyway I can create an extended WiFi connection thru the TC without hardwiring? I have a wifi extender (NetGear universal wifi range extender WGN3000) and was hoping that TC would connect to it and act as a second extender relay.
I hope my question is clear.
Also, is my understanding correct that if the TC is not hardwired, and it does not possess a wireless connection, then in order to backup my computer, I must connect to the basestation in Airport, and during that time I will be unable to use the internet??
THanks!!

We always say to people do the first backup by ethernet anyway.. wireless takes far too long.. once you are just doing incremental then it is ok by wireless.
But wireless halves in speed for every hop.. so make sure there is only ever one wireless link between the TC and the computer if at all possible. If you join it by wireless to the network.. you will have no gain.. and lots of pain.. plus half what are already poor speeds.. so you may as well just connect to the router by ethernet.. and bridge the TC.. you can then also setup wireless .. particularly 5ghz which the rest of your network probably doesn't use so you have a faster than normal link both to internet and TC for backup.. when you are in the same room.. link at 5ghz gives great speed and poor range.. go more than one room away and it will generally fall away to nothing.

Connecting Time Capsule wirelessly to Airport Extreme

Hello,
I have just purchased a Time Capsule v7.3.1. I am trying to have my Airport Extreme connect wirelessly to my Time Capsule and then use the ethernet connection "wired" to my Xbox. I am unable to get an ethernet address that works when connected via ethernet. I had two Airport extreme's previously connected via wireless and had my Xbox connected via Ethernet on my one Extreme and things worked fine. It seems that my Time Capsule when connected via wireless to my Airport Extreme isn't getting a valid ethernet DHCP address and I cannot get it to work. When I use the wireless connection on my Airport Extreme it seems to work fine when I access the wireless connection to the Airport Extreme. However, wired does not.. Time Capsule

your secondary router should be placed using the manual button once Airport Utility is launched in "bridge" mode. then configure your ethernet and wireless.

HOME HUB AND TIME CAPSULE WIRELESS CONNECTION

hi,
i have recently moved house and have BT broadband and Sky TV. The point where the master socket comes into my house is in an upstairs bedroom, well away from my living room where the TV is... So i'm wondering if its possible to have the Home Hub in the bedroom and then connect my apple time capsule wirelessly to it, then run ethernet from the TC to my Sky box for downloading TV etc. I may need to move the BT master socket to the living room, but hoping to find a workaround.
I have read some of the forums about bridging etc, but im not sure if this will solve the issue.
Any help would be appreciated!
Cheers

Since you, effectively, have two routers in series you will want to reconfigure the downstream router (the TC in this case) as a bridge to allow the upstream router (BT HomeHub) to continue to provide both NAT & DHCP services for all wired & wireless clients.
To set up the Time Capsule (TC) as a bridge, either connect to the TC's wireless network or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN port of the TC, and then, using the AirPort Utility, change this setting:
Internet - Internet Connection tab
o Connection Sharing: Off (Bridge Mode)
o Click Update to apply the new settings.

Mac connects but PC won't connect to internet via TIme Capsule wireless net

I have my personal Mac and work PC at home. I'm switching from a wireless network using my airport extreme base station to a new time capsule. Had no problems earlier, but now with my new wireless network I have the following problem:
- Both Mac and PC are able to connect to my home wireless network created through Time Capsule
- Only Mac can access the internet via the Time Capsule wireless network
- PC connects fine to the wireless network, but the settings indicate the internet cannot be accessed
I've tried fiddling with configurations etc. but cannot seem to get the PC to connect through to the internet using my Time Capsule.
The PC will connect directly to the net if I plug in the ethernet from my cable modem....What's the problem? Any ideas?

Welcome to the discussions forum AZR-DC.
The PC will connect directly to the net if I plug in the ethernet from my cable modem...
Make it a habit to power down your modem whenever you connect something different to it. Merely detaching the AEBS and attaching your Time Capsule or your computer directly will confuse most modems, so leave it powered down for a few moments. Power down your other equipment while you're at it.
Then, power up all the equipment as follows:
Modem... wait a few moments for it to complete its startup sequence.
Time Capsule. Wait a few moments again.
Computers.
Be sure your PC and your Mac are getting their addresses "via DHCP".

I am trying to connect my ipad to my bt home hub have put in wireless key code but still not connecting

i am trying to connect my ipad to my bt home hub have put in wireless key code but not connecting

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

HT5569 im trying to connect my ipad to my bt home hub put in wireless key pass code but still not working

im trying to connect my ipad to my bt home hub put in password still not working please help

Reboot your router by unplugging it for a couple of minutes, then try it again.

My MBP doesn't remember my Time Capsule wireless network when waking from sleep

My MBP (OS 10.5.8) doesn't remember my Time Capsule wireless network when waking from sleep. Thus, every time my MBP wakes from sleep, I need to select the Airport icon in the upper menu bar, select "Join other network", enter SSID and password. This is very cumbersome. And, I never had this problem when I was using the ISP's provided wireless router/gateway/DSL modem. Adding the Time Capsule and using it to generate the wireless network has introduced this problem.
It appears that this problem has to do with the hidden SSID. I don't need the lecture on how hidden SSID provides no serious security benefit. That's why I have the WPA2 encryption. I'm interested in a solution that will allow the Time Capsule to generate the wireless network, maintain a hidden SSID, continue to use WPA2 encryption, but have my MBP recognzie and autoconnect to this network.
Solutions I've alread tried:
1. Open Network Preferences
2. Select Airport from left hand column (and ensure Airport is at top of that list)
3. Select Advanced
4. Delete all Preferred Networks.
5. Apply settings.
6. Restart computer
7. Return to Network Preferences and from Advanced page, manually add my network with hidden SSID and WPA2 password
This solution works fine as long as I don't take my computer elsewhere and connect to another network. As soon as my preferred networks list gets another network, my MBP stops finding my TC network. Since I take my laptop to a lot of places (it's a laptop, after all...) this is a problem.
As I say, prior to adding the TC on my network (and using it to generate the wireless network), my MBP had no problem keeping 50+ preferred network names/passwords in the Preferred Network list, but always automatically finding/connecting to my home network without the need to "Join other network." Thus, I assume the problem lies with the Time Capsule.
Any ideas?

LaPastenague, thanks for weighing in. Didn't know that the hidden SSID capability was not IEEE standardized, and thus different devices will handle hidden SSID differently. With my admittedly limited knowledge of how SSID/hidden SSID works, I'm still a little confused as to why my MBP would remember the generic router/gateway's hidden network, but struggle with the TC's hidden network.
To my knowledge, when an SSID is broadcast by a base station (Airport, wireless gateway, etc.), a connecting device (like a laptop, iPad, etc.) detects this broadcast--this would be a passive reception of this SSID signal.
When an SSID is hidden, the base station does not broadcast its identification. Rather, a connecting device must transmit the name, and when the base station recognizes the broadcast, the connection is made. That's what you do when you select "Join another network" and manually enter the SSID.
The idea with OS X's Network Preferences is that these steps, whether for hidden networks or broadcast SSIDs, become automated.
Where is the potential for a different chipset between the TC and the previously used wireless router/gateway to alter this functionality? Shouldn't the selection of an SSID by the MBP to broadcast to seek for a base station be a function solely on the MBP? And once broadcast by the MBP, the TC should detect and reply?
Basically, the MBP can connect to the hidden TC manually just fine. The MBP can connect to the old setup automatically just fine. The MBP cannot connect to the TC automatically. Aren't these automatic connection functions solely on the MBP?
I'll try un-hiding the network and re-verifying that the problem is exclusively with the hidden network.
Z

Connect time capsule via ethernet to Mac for back-up only. Is it possible without internet connection ?

Connect time capsule via ethernet to Mac for back-up only. Is it possible without internet connection ?

Hi Bob,
I'm not certain the post I sent was posted correctly, as I added it as a reply to a 3-year old thread. Since this is a recently-active thread, though not specific to the issue at hand, I thought I'd post again:
Three years ago you helped me set up a roaming wireless network in my home. It's been rock-steady and I'm forever grateful to you for the time and guidance you gave me. I'd now like to swap out my AirPort Extreme base station for a time capsule. As I understand it, I should be able to unplug the base station and replace it with the TC without problem, so long as I use all the same settings on my TC... network name, security protocol, password, etc. Given the complexity of my network, I thought I should check with you first for any advice you might have. I don't want to set up a new network or make any changes to the existing one-- with the exception of using the TC in place of the AE. I'm already using Time Machine for backups. As a refresher, my current setup has the AE as base station and 3 expresses hard-wired with Ethernet connections elsewhere in my home. I have a 4th express set up wirelessly to use with my stereo system at the front of the house. All AXs are 'n's and are set up, as per your instructions, in Bridge mode to extend the existing network. I'm running the most updated version of Mavericks on my MBPro. Any suggestions you might have will be, as always, very much appreciated! Sincerely, Phyllis Sommers

Connecting time capsule wirelessly to BT home hub

Similar Messages

Maybe you are looking for