Connecting to 192.168.1.1 for checking router settings online brings non-English setup?

Bought a new WRT54G vers 6 router to replace a version 3 that died on us recently, and we have had many issues with SBC Global DSL connectivity, but when I go to the 192.168.1.1 site, it isn't in English, but in Italian or Spanish..
I can guess on some issues, but I never had a choice to pick what language this router page setup area would be in. Any ideas?
I could use some help here.

You need to download the correct firmware and upgrade or use tftp.exe.

Similar Messages

Trying to confiq cisco bridge WET200. connected to macbook ethernet port. entered 192.168.1.226 for config util. Times out.

I am trying to configure (due to WEP code on my wireless network) Cisco bridge WET200 for use in my home theater. To configure, I connected to ethernet port of macbook OS 10.6.8. Entered IP address 192.168.1.226 for config utility but it times out. Cisco says I need either IE or firefox. Downloaded firefox but still fails. Has anyone had experience with this?

Found that if I clean up DNS for my domain with PTR and A then everything started working properly after a rebuild.

Can't connect to 192.168.1.1 with WRT610N

Hi, i've been trying to add my sister's new laptop to the authorized MAC adress on the router, but i just can't get on the 192.168.1.1 administration page. When i type the adress in, the page loads for minutes, hours and even days with no result. I tired on the four computers connected to the routers but the page just loads forever and never shows.

Hi, I think I finally found the problems with not getting access to 192.168.1.1, or at least it works on my computer for now. Haven't tried it more than today, but I think this is the problem.
Turn of Linksys advisor program. Then try 192.168.1.1 It worked on my computer. The Linksys advisor loads on startup, and I think I will have the same problem again, if it starts up, so I will try to disable it in startup. I've also configured the network settings on the connection to internet protocol version 4 (TCP/IPv4) to use the following IP address of my computer (192.168.1.X), subnett 255.255.255.0 and default gateway to 192.168.1.1. Without those setting, ie obtain IP address automatically, I couldn't reach 192.168.1.1 You can manually start the Linksys advisor program afterwards, and I had no problems connecting to 192.168.1.1
I have tried every other solution mentioned on this forum, but nothing has worked for me. The most commoned answer is, reset your router or turn off the router, then it will work again. It does, but only for a day, or sometimes minutes, then its back to the same problem, with not being able to connect to 192.168.1.1 I have also downgraded the firmware and are using open DNS, but that didn't help. It seems to me that the problem is with the Linksys advisor program, kind of strange that I have read only one post mentioning that! But of course, I'm not 100% sure, but again, its working on my computer, and I can finally connect to the administration pages again!

Can't connect to 192.168.1.1 with my macbook. Tried reading all the posts no luck.

I've read through tons of posts and still no solution. I have powered everything on and off. I've tried firefox, safari, and netscape. I still cannot connect to 192.168.1.1 I have a befw11s4 v2. Along with not being able to connect to the setup page, my internet signal strength goes up and down constantly even though I am right next to the router.

If something does not work there is usually an error message which explains the problem. Please post the exact error message you get.
When wired to the router, open a terminal window and enter "ifconfig en0". Please post the output of that command.
Next enter "ping 192.168.1.1" and post what happens. Again, if there is an error message post the exact error message.

I am trying to run page 192.168.0.170 for my IP Cameras but after login and password the page is not responding. Plz help!

I am trying to run page 192.168.0.170 for viewing IP Cameras but after login and password the page is not responding. Plz help!

I am trying to run page 192.168.0.170 for viewing IP Cameras but after login and password the page is not responding. Plz help!

For connection to 192.168.1.1

Recently, I can not connect to the ip of 192.168.1.1. I can go into the internet. All my three computers can connect to the router via cable but only one computer can connect to it by wireless adapter. Also I can not succeed when to PING 192.168.1.1 . What is the problem? Is my router wrong with something?

Open a command prompt window and enter "ipconfig /all". Post the full output.

Can't connect to 192.168.1.1

Hi all! I'm having trouble getting my wireless router setup. I have a WRT54GS Ver.2 router. I seem to have misplaced the CD and I tried using the quick install but it didn't work. When I look at the network settings, my IP address is not 192.168.x.x but 99.x.x.x. I'm running XP with SP1. Any advice? Please help! Thanks a bunch! VK

check the following steps :
1)connect the computer to the router's port#1
2)connect the modem to the router's internet port
3)there shouldn't be any cables connected between the modem and the computer directly
4)reset the router for 30 seconds and do a power cycle
5)check the ip add again and if you get 192.168.1.x , try accessing the router using http://192.168.1.1

Trouble connecting to 192.168.1.1 & setting up wireless router

I am hoping someone can please help me!! I have a PowerMac G4 and a new 12" PowerBook G4. I received a Linksys router as a gift and I am having trouble setting it up...I have tried connecting to the ip address, http://192.168.1.1 with both Internet Explorer and Safari to no avail. I enter in the address and it tells me the connection has failed. I have tried numerous individuals including Linksys support and have had no luck! Can anyone help me or tell me what I may be doing wrong?
PowerMac G4 Mac OS X (10.3.1)
PowerMac G4 Mac OS X (10.3.1)
PowerMac G4 Mac OS X (10.3.1)

Lets start with some basic stuff.
First Shut your computer clear OFF.
Next pull the power adapter from your Internet
Service Providers Modem.
Next do the same thing with your New Router, Pull the
Plug on everything.
Remove any other USB items you might have connected
Printer scanner, camera.
Now you need to wait for 5 minutes.
NOW IN ORDER.
Plug the Ethernet cable from your ISP's Modem to your
Uplink port on your New Router.
Next
Plug the power adapter back in to your ISP'S Modem,
and wait until it re-aqiures the signal, depending on
the brand and who your service is with normally 3
lights.
Next after you are good on the modem you can plug in
your new Router, again wait for it to get it's signal
and lights.This will normally take a minute or so.
Now you can restart your computer.
After it boots up click on the Safari icon, and see
if it connects you.
If not go to the menu bar in your browser and type in
192.168.1.1
This should open the Linksys Utility box that will
enable you to confiqure your network.
Remember you will have to have all of the proper
setting in both your Browser and your Mail program
for everything to work properly.
Click on the Icon of Safari, and choose Preferences
this will allow you to setup
The same with Mail.
Good Luck Don
Hi, Don. Is the ethernet cable from the modem supposed to plug into the router's WAN port or the Uplink port?

Cannot connect to 192.168.1.1

I did a firmware upgrade on the BEFW11S4 yesterday and now I cannot access the web utility. I've tried ipconfig /release and /renew, but to no avail. I've also tried setting a static IP but that did not work as well. I did the firmware upgrade via wireless, and it gave me a success message after it was finished, but the router somehow lagged afterwards, so I did a reset on the utility and it connected. My internet connection is working fine, but I can't ping 192.168.1.1. My ipconfig returns:
Connection-specific DNS Suffix . : nyc.rr.com
IP Address. . . . . . . . . . . . : 24.193.219.59
Subnet Mask . . . . . . . . . . . : 255.255.252.0
Default Gateway . . . . . . . . . : 24.193.216.1
Any ideas? The default gateway should be 192.168.1.1 I've heard, but I have no idea how to set it without being able to communicate with the router.
I also did an IP scan on 192.168.0.* and 192.168.1.* and both returned all IP addresses in that range as dead.
Thanks.

Hey based on your IP check, it seems you are getting an IP address from your modem or from another device. Those IP's that you listed are actually valid IP's but they are not IP's that a private device like a router would give out.

Can't connect to 192.168.1.1 EA6500 or the Internet

Hi
Yesterday my router froze and wouldn't do anything, so I rebooted the router. When it got up and running again, I couldn't connect to the Internet. I got the error 502 - bad gateway.
I can't connect to it at 192.168.1.1 or linksyssmartwifi.com. I can ping 192.168.1.1, but not 8.8.8.8.
Ipconfig /all
DHCP yes
Ip 192.168.1.117
Subnet 255.255.255.0
Default gateway 192.168.1.1
DHCP server 192.168.1.1
I've tried flushdns, release and renew and it seems that the DHCP server from the router is working.
In windows it seems that there are an Internet connection.
I don't understand this, I can't visit any websites, but Spotify works.
I'm afraid it's broken and I have to buy a new router. I've triede to reset the router.
I hope that some of you can might help me.

Try disconnecting the router from the internet (WAN port) and plugging a PC directly into one of the LAN ports. After resetting, ignore the smartwifi login, click the two checkboxes, and login manually/directly with the "admin" password and reconfigure.
If you don't want to do all that just yet, try accessing the router from the public IP address assigned by your ISP. That might work

Hi. i have the sony hifi system "sony" a projector "sony" and the mac mini. the visual i have. the sound i don't. all is hdmi connected. apple is a new product for me. what settings fiddle with? please assist

i would like to know what settings i should use to able sound on my mac mini.
apple is a new product for me.
I've got a sony hifi with a sony projector. projector works fine. i do not have sound though.
they are all connected via hdmi.
please assist.

When you go System Preferences>Sounds>Output What output is selected?

Problem with my linksys WRT120N i can't connect to the address 192.168.1.1

Hello friends
i need help cuz i can't connect to the address 192.168.1.1
i didn't change the address 192.168.1.1 to an other address but i can't connect to this last i want to change my options
i really need help plz

Make sure that the computer is connected to the router on the Ethernet port..Now,check the ip address on the computer....Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies then,Adjust the Browser Settings on the computer....Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...

Windows 7 Static IP localhost connects but Static IP 192.168.0.127 does not

This is the error:
[Fiddler] The connection to '192.168.0.127' failed.
Error: ConnectionRefused (0x274d).
System.Net.Sockets.SocketException No connection could be made because the target machine actively refused it 192.168.0.127:16020

Connection refused is most commonly due to firewall.
Disable windows firewalla s a test an if it prooves the cause re-enable it and configure the appropriate exception(s).
Also check if the might be an infrastucure firewall in place.
MCP/MCSA/MCTS/MCITP

Can't access three routers through 192.168.1.1, Not address of router. HELP?

Long story here, and I am baffled...
My parents were initially connected to a broadband connection through a wired BEFSX41 router. After moving the computers to another room had major connectivity issues. Tried to access router through 192.168.1.1 and could not. Ran ipconfig and found address to be 76.180.104.1. Tried reset, power cycles, release and renew, could not get it to go back to 192.168.1.1. Brought a WRT54G I had over, had normal results for a brief period(10 seconds tops) then again, same ip address and connectivity issues. After this I brought both routers home, connected them to my laptop, but not my network, inspected the configurations and updated firmware, with no issues. So to narrow down issues I brought the WRT54G to my sisters house. She runs a WRT160N. Before changing anything I accessed 160N through webpage, checked settings and verified ip through ipconfig to be 192.168.1.1. All ok. Replaced her 160N with 54G and had wrong ip address again, also 76.180.104.1, so I decided router was somehow damaged/corrupted. This is where this story turns really crappy for me. When I reconnected the 160N, the ip address was 192.168.1.1 for 15 seconds, then in ipconfig two ip addresses were shown suddenly. They were 76.180.96.1 and 192.168.1.1. Ran ipconfig again and got only 76.180.96.1, and now I can no longer access router.
My sister talked to a knowledgeable guy she knows before I hooked it to her computer and he surmised a Google redirect virus which I did sign on to. But now it seems the 54G router has transferred this virus/issue to my sisters computer, which then uploaded it to her 160N. Judging by the time delay when initially connecting 54G, I think maybe this virus is somehow corrupting routers? Does this sound possible to anyone? And if so, what are my options to save the routers, and not have to re-image computer drives? Anyone with any knowledge, please help, cause the idea of having to re-image three computers is killing me. Also I did not leave any of the routers with the original password. Thank you in advance for your help.

Good. The symptoms you saw (computer gets public IP address) is most commonly because you connect one of the LAN ports of the router to your modem. That way the computer can talk directly to the modem and gets a public IP address.
Sometimes this can happen if the router crashes and won't boot up (often power light is blinking). In that case, the switch in the router won't separate the internet port from the LAN port again giving computers direct access to the modem.

Cant access 192.168.1.1

I've been having error 322 come up, and i have spent time with on Live Chat with Tech Support trying to figure out what the F is going on. I cannot access 192.168.1.1 in IE. Which has disabled me from reconfiguring. My gateway IP is 71.231.48.1, and i was told that it needs to be 192.168.1.1. I sure could use an easy answer, between my PS3 and this router, i'm ready to throw em all out.

Check the ip address you are getting on the computer which is connected to the router...Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies,Adjusting Browser Settings : Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...

Connecting to 192.168.1.1 for checking router settings online brings non-English setup?

Similar Messages

Maybe you are looking for