Connecting to a Stereo Recei

How would I attach my Zen Micro to a Stereo Recei'ver?
Thanks

You need a cable with a stereo mini jack on one end and RCA jacks on the other. Very common cable available at any stereo or electronics store. Plug the mini jack into the Micros' headphone jack, plug the RCA ends into aux. or any input other than phono, adjust volume on micro so there is no distortion, but strong signal...around 20 or so and enjoy.

Similar Messages

Problem connecting Audigy to stereo recei

Hi,
My system is a home built using XP home, SP2.
I'm trying to connect my Audigy sound car to my stereo receiver and also still have it connected to the desktop speakers. Bought a splitter and plugged it it into the line out jack and then plugged the desktop speaker wire into one output and the other into an rca splitter which I attached to the left and right wires from the receiver.
Problem is there is no sound on the right channel of the desktop speakers or the reciever.
Strange thing is if I unplug the wires leading to the receiver I get sound on both channels of the desktop speakers. If I plug the receiver back in I don't get sound on the right channel of either and if I unplug the desktop speakers I still don't get sound on the right channel of receiver.
Have tried different splitters and switching which side the speakers and receiver are plugged into with exactly the same results.
Any help appreciated. Have looked online and in the faqs and haven't found a solution.
Francis

have you tried going directly from your soundcard directly into your reciever? if you're going stereo mini plug (tip/ring/sleeve, /8", stereo), out to dual rca directly into your reciever, you should be in good shape. give that a whirl and see what happens.

"Comm Error" message when connecting to car stereo

When connecting my 80G IPod to the port in my car, the IPod screen rolls horizontally, then says "OK to disconnect", and the stereo displays the "Comm Error" message. I was able to connect to the stereo before but don't know what happened to cause this. Re-setting the IPod did not resolve the problem. Has anyone else seen this? Please help!
5th Generation IPod Windows XP

I’ve got a 30gb ipod doing the same thing. I know it’s not the car as my friends nano works fine on it. Have you have any success?

TS1382 Can my iPod Classic 160GB model MB565LL version 2.0.1 Mac be controlled with my Apple Remote if it is connected to the universal dock and connected to my stereo system

Can my iPod Classic 160GB model MB565LL version 2.0.1 Mac be controlled with my Apple Remote if it is connected to the universal dock and connected to my stereo system

Read this Apple Support Article on Apple REMOTE
Good luck!

Can my iPod Classic 160GB model MB565LL version 2.0.1 Mac be controlled with my Apple Remote if it is connected to the universal dock and connected to my stereo system

Can my iPod Classic 160GB model MB565LL version 2.0.1 Mac be controlled with my Apple Remote if it is connected to the universal dock and connected to my stereo system

Read this Apple Support Article on Apple REMOTE
Good luck!

Connection to Car Stereo

I have an ipod connection into my car stereo in my Infiniti. I was hoping to replace my ipod with my Blackberry Storm and be able to play it through my stereo system. Is there a cable that will fit my car connection and the Storm?

First, I don't know what type of connection your car stereo has, but as for me, I am using a simple male 3.5mm to RCA jack cable (See link below) for my car and it works wonderfully.
http://www.buy.com/retail/product.asp?sku=203945380&listingid=32518714&dcaid=17902
Message Edited by enzo_mmx on 12-10-2008 12:46 PM

Connecting iMac to stereo receiver

I am trying to figure out the best way to connect my iMac to a stereo receiver. Which option will result in superior sound on my home stereo: (1) running a TOSLINK cable from the iMac's optical digital audio out port to the receiver's optical input or (2) connecting the iMac to the receiver using a USB DAC?
Thanks for your help.

I do not agree. The headphone amp outputs a conventional two channel analog signal on the multi-purpose 3.5 mm audio output jack on all Intel iMacs. But that same jack outputs a digital optical signal if the iMac senses a mini-Toslink adaptor plug has been inserted instead of an analog stereo TRS (tip ring sleeve) plug.
IOW, the same jack furnishes two entirely different kinds of output (analog or digital) depending on what is plugged into it. The digital output encodes the audio (which could consist of multiple channels of audio) on a single beam of digitally modulated light. The analog output is two separate signals, each on its own electrical conductor, derived from the internal DAC in the iMac & amplified by the amp to provide enough power to drive headphones.
It is possible that the amp does double duty to also drive the light source for the digital output, but that is in no way is comparable to using it to drive headphones -- for the digital output all it would have to do is switch the light level between the digital high & low states.
My guess is that whoever told you about the headphone amp either did not know about the dual function of the jack or thought you were talking about an analog connection to your stereo.

IPad is connected to a stereo installation - no control of the volume by the iPad

When my iPad is connected to a stereo installation, there is no possibility anymore to control the volume by the iPad.
'the volume control' is replaced by 'dock connector' on the iPad

This issue manifests as The volume control shows sound effects on screen or phantom docking no volume slide control.
For the beginners, the issue is often the side switch is set to mute on off and not screen rotation lock. The switch is off. (see settings)
Other issues around software and airport use can be resolved by hard reset, or reset options inside the settings. I use AIRPORT all the time.
You may have even tried the re-installing the firmware/ios
So when all has failed to work, the you may have dock connector PIN 21 problem.
I had an issue that started with the ipad whe it was on USB cable to PC.
No drop, no sudden cable movements. Just gone....
No volume slider. IPAD behaves as if it was docked when not.
Slight movement when usb cable is in occasionally brings the volume control back but only for a few seconds then it disappears.
Mine is going back for repair/replacement.
cheers Phil

Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear-) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay

Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear…) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay to my Ipad. My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library? I`d appreciate any help. Alex.

My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library?
On the iPad you can stream videos, photos, or music from the Video, Photos, Music, and YouTube apps to an Apple TV OR just stream music to an AirPort Express Base Station.

Hello I have 2 seperate airport express systems on my network, each connecting to a stereo in a different room. suddenly, the one in the living room will not stop flashing amber, but the one in the bedroom works fine. I have already tried resetting it

Hello
I have 2 seperate airport express systems on my network, each connecting to a stereo in a different room. suddenly, the one in the living room will not stop flashing amber, but the one in the bedroom works fine. I have already tried resetting it with a pin, resetting it while plugging it in, and trying to find it in airport express setup (the setup assistant can't find it at all).
What am i doing wrong?

How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX.

Had a Airport Express connected to my stereo and it was working. I brought an Airport Extreme and suddenly it took over and Airport Express stopped working and disappeared from Airport Utility. What I am supposed to do? ar2ro

I have an Airport Express connected to my stereo and it was working without any problem.
Recently I bought an Airport Extreme to use it as my Base Unit connecting it to my DSL.
I followed the instructions of the Airport Utility, and it started working.
Suddenly, problems started happen the Airport express that was connected to the stereo , stopped working and it disappeared from the Airport Utility area , as it did not exist in the network. I tried to reset it but it did not appear in the Airport Utility page.
Apparently I have other problems with the private network that it created because I cannot use it because of problems with the password that was created. I can only use the network that I created for my guest...
I dont know if my problem is a configuration problem or there is problem with the equipment.
I read that other users where having the same problem with the Airport express , using non apple equipment as their base unit , but I thought that using the Airport Extreme was going to be compatible and no problems would happen.
What should I do?

Common Problem. Common solution.
Connect your Express via ethernet cable to the Mac while other network connections on the Mac are switched OFF.
After the Express shows up, change the settings of the Express to join the existing network. Take the appr. settings.
Unplug and reconnect your Mac to the network.
Check if the Express shows up in Airport Utility
Alternative solution:
Hardreset the Express to factory settings
(while on power push the Pin next to the audio plug with a paperclip. Plug out the Express still holding down the little button then replug the Express to power and release button)
After that, the Express will show up in the Airport Utility.
Make all needed settings.
I would prefer the first solution, its easier just to plug a cat5 cable.

Poor Sound Connected to Home Stereo

I have a 30 GB 5th Gen Video iPod that I connected to my stereo via the headphone jack using the monster cables I bought at the Apple Store. The sounds is not good at all. It's night and day vs. a CD. Is this normal.

Try getting the Apple Universal Dock; the Line Out port reportedly sounds better than the iPod headphone jack (although it really isn't Line Out, since you can adjust the volume with the Apple Remote). If possible use a 2-wire stereo mini-plug cable (or the Monster iTV Link cable which combines a stereo cable and an S-video cable) rather than a 3-wire AV mini-plug cable.

After iOS5 update, iPod no longer connects to car stereo

Hi,
my husband and I both have an iPod touch 4th generation.
We also have a Dodge Caravan with a car stereo, that lets up hook up the iPods and control them over the display. The cable does not charge the iPods, but we knew that.
I have updatedt my iPod a while ago and never encountered any problems with the car stereo.
My husband updated his iPod to iOS5 today, and the car stereo does not connect via the cable. On the iPods display it just says, an error has ocurred.
Would that be a hardware issue? The iPod is a month or two past warranty. We already tried restarting and resetting the iPod (not to factory settings).
Is there maybe a way, to return the iPod to iOS4?
Thanks for any help

Sometimes, when you cannot "see" your ipod, it is because the drive that was assigned to the ipod, when you connected it, is already being used by the other devise. Your ipod is connected, but is "under" the other item, which means that you have to disconnect that item, so that you can "see" it. It will not be one of the drives that are normally associated with the computer like the C drive, or the ones assigned to your disc drives. It would be a drive that was assigned to an external devise, or another USB devise. This may or may not be your problem, but it is worth a shot.

IOS6 bluetooth connection with car stereo

With my iPhone 4S running iOS5, my after-market car stereo bluetooth was able to read my song name, artist name, ect. Now that I upgraded to iOS6 my Kenwood receiver cannot read this data while connected via bluetooth. Since the data can't be read, the steering wheel control to search/skip a song forward or back also no longer works. I tested the car stereo last night with an iOS5 phone and it worked correctly, so I know the problem is related to the bluetooth iOS6.

Dear Valued Pioneer Customer:
We would like to inform you of the availability of an optional Bluetooth® firmware update (HW05-SW01.27.20) that enables Bluetooth AVRCP control and metadata display from a compatible Pioneer CD or DVD Receiver when used with an iPhone® 5 or iOS 6 device. If you do not own an iPhone 5 or iOS 6 device, there is no need to install this update.
This firmware update may be used only with the following 2012 Pioneer products:
CD Receivers
DVD Receivers
DEH-P8400BH
DEH-P9400BH
DEH-80PRS
AVH-P2400BT
AVH-P3400BH
AVH-P4400BH
AVH-P8400BH
In order to perform this update, the following items are needed:
A Pioneer CD or DVD Receiver above with built-in Bluetooth
Laptop with built-in Bluetooth running Windows® 7
Bluetooth firmware update (HW05-SW01.27.20)
How to Obtain the Free Firmware Update
1. Download the INSTRUCTIONS for the optional Bluetooth firmware update (HW05_SW01.27.20).
2. Download the UPDATE FILE to a computer and transfer the file to a compatible 2012 Pioneer CD or DVD Receiver via a Bluetooth-enabled Windows 7 laptop.
You can also arrange for Pioneer to update your 2012 Pioneer CD or DVD Receiver by calling Pioneer Customer Service toll free at 800-421-1404 during regular business hours (M-F 10AM-7:30PM Eastern Time, except on holidays). If this firmware update is performed by Pioneer, there is a charge of $60.00 (this charge includes return shipping of the updated unit within the U.S.). Charges for removal/reinstallation of the unit and shipment to Pioneer are the customer’s responsibility.
How to Determine if the Firware Update has Already been Installed
CD Receivers:
• With the unit turned off (press and hold the source button until the CD Receiver turns off), press and hold the center of the volume knob to bring up the Settings menu → rotate the volume knob until "BT Version Info" is displayed and then press the center of the volume knob → The firmware version should show HW05-SW01.27.20.
DVD Receivers:
• With the unit turned off (press the home button and select ‘OFF’ from the source icons), press the home button → Press the “System” icon at the bottom of the screen → Select the “Bluetooth Version Info” option → The firmware version should show HW05-SW01.27.20.
If the Bluetooth firmware version shows HW05-SW01.27.20, no further action is necessary.
Questions
If you have any questions, please contact the Pioneer Customer Service Center toll free at 1-800-421-1404, Monday through Friday, 10:00 a.m. to 7:30 p.m. (Eastern Time), except on holidays.
Sincerely,
Pioneer Electronics (USA) Inc.

Issues with USB connection to car stereo

I just got an iPhone a few weeks ago, and generally it's great, but I have frequent issues when connecting it to my new Pioneer DEH-P3100UB car stereo. I think it may be kind of new in that it doesn't have a "special cable" for connecting to the iPhone, it just uses the typical USB sync cable.
When I see the problem, the stereo reports error 19, which the manual calls a communication failure, and suggests turning the car off and back on, unplugging and replugging the USB device, or switching to a different audio source and then back to USB.
Generally, none of these suggestions work, but power cycling my iPhone always does. This doesn't seem like it should be necessary. Has anyone else had problems like this? Is this a problem with the iPhone software that might be addressed in a future software update?
Thanks!

Hey jrbapple,
Keeping your iPhone updated is a good idea. If you iPhone isn't already updated to iPhone software 2.2.1, try updating it now.
http://www.apple.com/iphone/softwareupdate/
Does the car stereo have the "Works With iPhone" logo?
You can find more information about the logo and Apple certified accessories here: http://support.apple.com/kb/HT1665
-Jason

Connecting to a Stereo Recei

Similar Messages

Maybe you are looking for