Connecting to Aironet 1130AG through Hyperterminal

We have a wired Aironet 1130AG which we cannot connect to. We got a cable to hook it up to a computer with the Hyperterminal. But we don't know the commands to connect to it. Can anyone give us some advice?
Thanks
Mike

Hi Mike,
You will need these settings on your Hyperterminal session;
Baud rate: 9600
Data: 8 bit
Parity: none
Stop: 1 bit
Flow Control: None
Hope this helps!
Rob

Similar Messages

Windows 7 problem connecting to Aironet 1130AG AP

We currently have Windows XP Pro laptops that are configured to connect with our Cisco Aironet 1130AG Access Point and everything works fine. I am trying to configure new Windows 7 laptops using the same settings we used for the XP Pro laptops and they will not connect to the AP. Have any of you run into configuration issues with Windows 7 and Cisco wireless access point connectivity and found a solution? Is there any documenation on how to configure Windows 7 with Cisco Aironet 1130AG Access Points?

The wireless card is a Dell DW1501 wireless N WLAN Half Mini Card (Broadcom is the manufacturer).
I had the router setup to not broadcast. I changed it to broadcast and Windows 7 still will not connect. Do you have any other suggestions? Windows 7 is 32-bit on the laptops and I read somewhere online that mentioned they had the same problems with 32-bit but not 64-bit. The XP laptops wireless configuration is WPA-Enterprise with Cisco Leap along with user name and password.

Windows Client cannot connect to wireless LAN through EAP-TLS

I have a Cisco Aironet Access point which cannot be authenticated by a remote RADIUS server to connect to wireless lan through EAP-TLS. These is the debug output from the AAA process.
*Mar 7 10:56:56.337: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:56:56.369: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:56.385: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:56.385: dot11_auth_parse_client_pak: id is not matching req-id:1re
sp-id:2, waiting for response
*Mar 7 10:56:56.401: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:56.717: dot11_auth_dot1x_parse_aaa_resp: Received server response:
GET_CHALLENGE_RESPONSE
*Mar 7 10:56:56.717: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server r
esponse
*Mar 7 10:56:56.785: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:57.097: dot11_auth_dot1x_parse_aaa_resp: Received server response:
GET_CHALLENGE_RESPONSE
*Mar 7 10:56:57.097: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server r
esponse
*Mar 7 10:56:57.101: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:57.393: dot11_auth_dot1x_parse_aaa_resp: Received server response:
GET_CHALLENGE_RESPONSE
*Mar 7 10:56:57.393: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server r
esponse
*Mar 7 10:56:57.397: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:57.673: dot11_auth_dot1x_parse_aaa_resp: Received server response:
GET_CHALLENGE_RESPONSE
*Mar 7 10:56:57.673: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server r
esponse
*Mar 7 10:56:57.677: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:57.953: dot11_auth_dot1x_parse_aaa_resp: Received server response:
GET_CHALLENGE_RESPONSE
*Mar 7 10:56:57.953: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server r
esponse
*Mar 7 10:56:57.957: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:58.317: dot11_auth_dot1x_parse_aaa_resp: Received server response:
GET_CHALLENGE_RESPONSE
*Mar 7 10:56:58.317: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server r
esponse
*Mar 7 10:56:58.321: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:58.685: dot11_auth_dot1x_parse_aaa_resp: Received server response:
GET_CHALLENGE_RESPONSE
*Mar 7 10:56:58.685: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server r
esponse
*Mar 7 10:56:58.685: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:56:58.993: dot11_auth_dot1x_parse_aaa_resp: Received server response:
GET_CHALLENGE_RESPONSE
*Mar 7 10:56:58.993: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server r
esponse
*Mar 7 10:56:59.041: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:57:01.077: Client 0811.9650.8cb0 failed: reached maximum retries
*Mar 7 10:57:08.997: %RADIUS-4-RADIUS_DEAD: RADIUS server 165.72.12.12:1812,181
3 is not responding.
*Mar 7 10:57:08.997: %RADIUS-4-RADIUS_ALIVE: RADIUS server 165.72.12.12:1812,18
13 is being marked alive.
*Mar 7 10:57:14.481: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:57:14.521: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:57:44.521: %DOT11-7-AUTH_FAILED: Station 0811.9650.8cb0 Authenticatio
n failed
*Mar 7 10:57:44.801: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:57:44.829: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:58:14.829: %DOT11-7-AUTH_FAILED: Station 0811.9650.8cb0 Authenticatio
n failed
*Mar 7 10:58:15.105: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:58:15.141: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:58:45.141: %DOT11-7-AUTH_FAILED: Station 0811.9650.8cb0 Authenticatio
n failed
*Mar 7 10:58:45.425: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:58:45.449: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:59:15.449: %DOT11-7-AUTH_FAILED: Station 0811.9650.8cb0 Authenticatio
n failed
*Mar 7 10:59:15.729: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:59:15.753: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:59:45.753: %DOT11-7-AUTH_FAILED: Station 0811.9650.8cb0 Authenticatio
n failed
*Mar 7 10:59:46.009: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:59:46.037: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:59:50.077: Client 0811.9650.8cb0 failed: reached maximum retries
*Mar 7 10:59:50.349: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:59:50.373: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 10:59:55.077: Client 0811.9650.8cb0 failed: reached maximum retries
*Mar 7 10:59:55.341: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 10:59:55.361: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 11:00:00.077: Client 0811.9650.8cb0 failed: reached maximum retries
*Mar 7 11:00:00.333: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 11:00:00.357: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 11:00:05.077: Client 0811.9650.8cb0 failed: reached maximum retries
*Mar 7 11:00:05.341: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
*Mar 7 11:00:05.365: dot11_auth_parse_client_pak: Received EAPOL packet from 08
11.9650.8cb0
*Mar 7 11:00:10.077: Client 0811.9650.8cb0 failed: reached maximum retries

Kindly get verified the configuration and the compatibility if there is a mismatch. Please find the link below for more information on EAP-TLS functions in Access points and clients.
http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_white_paper09186a008009256b.shtml#wp39110

Cisco Aironet 1130AG WPA2 Configuration

Hi everyone,
First of all, let me introduice myself. I just graduated as an IT-engineer and started working in a company who gives support to their users, but also does installations. One day a week I am permanent located with 1 customer. I give support to users, but also implement new systems. I really love networking, but it's really not my strongest point. Especcialy when it comes to CLI. So I was hoping you could help me.
With this customer they have 4 floors with on each floor a Cisco Aironet 1130AG. At the moment they are using WEP as a protection with a really long key. The users find this annoying, but I am more concerned about the security perspective. So I want to implement WPA2 with a shorter key for the people to remember. On one floor, I also want to add a public network when other people want to connect and just need internet access.
Is it possible you guys could help me change the current set-up and give advices regarding the security and implementation. For me I would be great if all of the Access Points could work togheter and just be 1 wireless network. I don't know if this is possible and how to do it? For the public network I know there also need to be some changes in VLAN's, so I would appreciate the help there for setting up trunks. The firewall is a cisco ASA5505.
At the moment I am running this configuration:
I tried setting up this with the GUI, but it doesn't look like the configuration at the moment is shown in the GUI or maybe I am just looking in the wrong places.
Thanks again for helping me configure this!! Much appreciated!
!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname CISCO-AP-V0!enable secret 5 $1$vhoF$wv3N1r1sMiiuhGgQTpx5b0!no aaa new-model!!!dot11 ssid private-v0 authentication open guest-mode!power inline negotiation prestandard source!!username Cisco password 7 14341B180F0B!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption key 1 size 128bit 7 FD0B4EB47C9301A55E6A685157C8 transmit-key encryption mode wep mandatory ! ssid private-v0 ! speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 packet retries 128 drop-packet station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption key 1 size 128bit 7 4A476E1E760D683C46307A755A29 transmit-key encryption mode wep mandatory ! ssid private-v0 ! no dfs band block speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface FastEthernet0 no ip address no ip route-cache duplex auto speed auto bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.2.220 255.255.255.0 no ip route-cache!ip default-gateway 192.168.2.1ip http serverno ip http secure-serverip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eagbridge 1 route ip!!!line con 0line vty 0 4 login local!end

Look at those:
www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008054339e.shtml
www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008055c39a.shtml
HTH
Amjad

Aironet 1130ag GUI problem

i can't have access into Cisco Aironet 1130ag via GUI. Meanwhile, i could ping it. Kindly assist

Hi Fafolahan,
Just to add a note to the good info from Scott (+5 points here Scott :)
Converting a Lightweight Access Point Back to Autonomous Mode
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 6 Disconnect power from the access point.
Step 7 Press and hold MODE while you reconnect power to the access point.
Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
From this excellent doc;
http://www.cisco.com/en/US/customer/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Hope this helps!
Rob

DHCP Server Assignment - Aironet 1130AG

I am attempting to configure a Cisco Aironet 1130AG to use a Windows Server 2003 DHCP server for assigning addresses to clients connecting to the access point. Does anyone know how to set this option? I cannot find it anywhere.
Any help will be greatly appreciated.

I'm having more or less the same problem but mine is even more low level than this. I have three 1130ag's that were setup in as PEEP authentication. The PEEP was proving to be a problem for whatever reason and we decided to go with WEP authentication and have the 1130's be regular old APs. Well apparently they can't or won't do that. I set one up as a standalone AP and it actually worked for about three weeks giving out DHCP addys to laptops then one day decided it wouldn't anymore. So I reset it using the MODE button and put the same information back into the device. Now it will allow clients to connect but never gives them a DHCP addy. We don't have and never had a Cisco Wireless controller and these have been working as PEEP WAPs for well at least a year or so. Why won't they simply give out DHCP to the clients?

Aironet 1130ag RAIDUS auth issues - what is no sg in radius-timers?

Hi All.
wonder if anyone can help
We have an aironet 1130ag in a remote office connected to the data centre over MPLS. The Radius server is based on server 2003
We have hundreds of these points set up exactly the same but this is the only one giving me issues, I even stripped the config and rebuilt it and then swapped with a new access point
The issue is that clients can't authenticate when connecting to the access point but provides nothing in event viewer. Checking the RADIUs server provides nothing either.
The access point error logs just state station: authentication failed
On looking deeper into the problem I enabled RADIUS debugging on the access point and got some interesting results, in particular is the line:
no sg in radius-timers: ctx 0x12EF0A4 sg 0x0000
I can't find out what no SG in Radius-timers actually means, but after that line appears I just see more retransmits and no sg fails.
I inspected the packets on the RADIUs server and found lots access requests coming from my access point and lots of access-challenges returning back from my RADIUS server - I'm not sure how often that's supposed to happen or if it's a one time occurance. I did however see directly after the first access-request that the RADIUS server returns with UDP and is fragmented, length is 1514...... could this be the problem? If so why cannot it hanlde fragmented packets? And what do I need to do to fix?
Many thanks for the help
Mark

the fragmented packet might be a red herring as I've just done the same packet inspection on the same radius server but coming from a different access point which works, I get the same fragmented UDP packet but the connection works.
any ideas?

Aironet 1130AG Help

I have 4 Aironet 1130AG WAP's
How do I configure them to use WPA Without a RADIUS server?
I have got one of them set up by adding a VLAN and a SSID and used in encription manager I set Cypher to TKIP.
In SSID I have set Key management to mandatory checked WPA and set the WPA pre-shared key.
On my laptop I can see the SSID and it is listed as Security Enabled network (WPA)
When I try to connect and and enter the WPA pre-shared key it tries to connect and never does, but the connection changes to Automatic.
How do I get these to work?
Thanks

Unless you need VLANs for your network you don't need to configure any on the AP to make this work and that may be where your problem lies. Try removing the VLAN and see if that helps.

Aironet 1130AG

I have 4 Aironet 1130AG WAP's
How do I configure them to use WPA Without a RADIUS server?
I have got one of them set up by adding a VLAN and a SSID and used in encription manager I set Cypher to TKIP.
In SSID I have set Key management to mandatory checked WPA and set the WPA pre-shared key.
On my laptop I can see the SSID and it is listed as Security Enabled network (WPA)
When I try to connect and and enter the WPA pre-shared key it tries to connect and never does, but the connection changes to Automatic.
How do I get these to work?
Thanks

so far I an get this AP to act as a radius server to auth other AP's and users accessing the AP with passwords - will send the config if requested....

POE on Aironet 1130ag failes

Hi, I am trying to enable POE on our three new Aironet 1130ag but they fail to get the power from 6500 switches which have WS-X6348 modules and WS-F6K-VPWR sub modules. I disabled power injector and tried power negotiation and pre-standard compatibility without any success. Thanks.

Hi Reza,
I think you have already figured out the problem here :) This module - WS-F6K-VPWR only supplies 7W of PoE power and the 1130 requires 802.3af 15W PoE;
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_10826.html#wp31976
We had this happen to us recently due to a PoE problem. The 1130 requires either IEEE 802.3af power or needs a setting on the WLC for using power injector or Cisco Pre-Standard PoE. Our older switches could only provide Cisco Pre-Standard PoE so we had to tweak the WLC Power setting for these AP's. Once we did that the Radios came right up. Here is a reference;
You may have to enter the following info in the WLC;
While the AP boots, with its Intelligent Power Management feature, it negotiates with the switch via Cisco Discovery Protocol messages in order to provide the necessary power to the AP. Even though the power injector is connected to the AP, the AP that uses this Intelligent Power Management feature gives priority to the Cisco Discovery Protocol information in order to identify whether or not the switch can provide the power. Therefore, after the Cisco Discovery Protocol message shows that the switch does not provide sufficient power (since it is not an inline power capable switch), the AP disables its radios. At this time, the status LED of the AP turns orange and this error message is recorded:
[ERROR] : AP has not enough in-line power
to enable radio slot 1 In order to overcome this problem, issue the
config ap power injector enable installed
command on the controller that is connected with this AP. This command is available from controller version 3.2.116.21. Ensure that you use the correct version in the controller.
This command specifies that a power injector is used in order to supply sufficient power to the AP.
From this doc;
Cisco Aironet and WLAN Controller Product Power Options
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a00800946e7.sh
Have a look at this good Q&A;
Q. As with the 1200 Series AP, can a 1130/1240 AP work with 7 watts of power to it from a pre-standard POE with 802.11g radio alone disabled?
A. No, the power consumption on the AP1240 breaks down like this:
5 GHz only radio 11.56 watts
2.4 GHz only radio 12.96 watts
Both radios on 15.0 watts
The power consumption on the AP1130 breaks down like this:
5 GHz only radio 9.750 watts
2.4 GHz only radio 9.910 watts
Both radios on 12.20 watts
In either case, you can see that, for the AP to operate with a single radio, it requires more than 7 watts of power.
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a00806a4da3.shtml
Hope this helps!
Rob

How on earth could I be connecting to the Internet through my airport express when it is not connected to anything?

I'm not entirely displeased with the situation but I cannot see how I could be connecting to the Internet through my airport express when the Airport is not connected to anything.
Weird huh?
I have a separate non- Airport wireless network connected to the Internet. I had previously set-up the Airport to link with this network but disconnected it (by resetting it) as music streaming was unlistenable due to frequent drop out. I now just have the Airport Express as a standalone wireless network only connecting to the stereo to stream music from devices.
My devices are only connected to the Airport network with cellular data off. Yet I can still connect to the Internet AND listen to streaming music (without drop-out no less).
I don't want to fix it but I would like to know how the frag it could happen so i don't screw it up accidentally.

I would say you still have something of the previous setup.
To be sure you don't mess up, save the configuration.. go to the top menu area of the airport utility and export configuration.. which will land on your computer.
Now you can recover at anytime to the current setup.
How it works.. that is magical ..
Open the airport utility.. edit.. and take a screenshot and post it of the following pages..
Internet wireless network
THen we can tell you how it is working.

I am trying to connect my macbook air through my led tv using hdmi but it won't work. I could not find arrangement option on my system preference. how do i make it appear again on my system preference so i can mirror it through my tv. thanks

I am trying to connect my macbook air through my led tv using hdmi but it won't work. I could not find arrangement option on my system preference. how do i make it appear again on my system preference so i can mirror it through my tv. thanks

Hi jenette,
If you are having issues using an HDTV via HDMI as an external display to your MacBook Air, you may find the following article helpful:
OS X: How to use multiple displays with your Mac in Mountain Lion and earlier
http://support.apple.com/kb/ht5019
(Note: You will generally only see the arrangement option in Displays when you are configured to use the external display in Extended Desktop mode; there is no arrangement in Mirroring as both screens are showing the same image.)
Regards,
- Brenden

My MacBook pro will not connect to the Internet through wifi yet all other devices do

My MacBook pro will not connect to the Internet through wifi. I have several other wifi enabled devices and they are all connected to the Internet just fine... What could/would cause this?

Disable your AirPort and enable in a second. Or check, maybe you need to type in correct digits in; Settings/Network/Advanced/Configure...

I have an iPhone 4s, and I reset the content and setting. It turned on, I chose English, Australia, and now, I am unable to connect/activate my iPhone through Wi-Fi, and for an unknown reason, it will not allow me to use cellular data or iTunes.

I have an iPhone 4s, and I reset the content and setting. It turned on, I chose English, Australia, and now, I am unable to connect/activate my iPhone through Wi-Fi, and for an unknown reason, it will not allow me to use cellular data or iTunes. I'm not sure of what to do. It's quite frustrating, and all I need is advice, and help. I would much appreciate it. Thank-you.

In order to download to your phone over the air, you need to be connected to WiFi.
It's possible the Internet connection through Verizon is not stable enough for the downlaod to begin (it is a very large download).
You might want to head over to Starbucks with your laptop for the afternoon and see if you can download it over their WiFi.

How can I know which clients are connected to my network through express and which are connected through extreme?

I have an airport express extending, through wireless, a network provided by an airport extreme. How can I know which clients are connected to my network through express and which are connected through extreme?
Here you can see both routers:
I would expect to some clients connected to the express, other than the extreme. And that's all I see: only the airport extreme appears as client of the airport express.
Below, one can see the summary of the config for both routers.
Would somebody explain it?
Thanks,
Marcelo
Message was edited by: Marcelão

please disregard this answer.
Message was edited by: Marcelão

Connecting to Aironet 1130AG through Hyperterminal

Similar Messages

Maybe you are looking for