Connecting to Base Stations with an ethernet cable

Hi. Can anyone help figure this out please.
We have two airport extreme base stations at opposite ends of the building with one connected to the internet and printer etc and the other extending the network so everyone can access these services and each other.
Because they're some distance apart, we've connected the two base stations by ethernet cable with the second base station extending the network in Bridge Mode.
I can't figure out whether the ethernet cable from the main base station should go into the WAN or LAN ports on the back of the other base station. I've tried both and at the moment neither seem to be working.
Both base stations are brand new and the most recent model.
Can anyone advice on which port to sue and any settings I should be paying attention to please.
Cheers.

Welcome to the discussion area, chriscurtis!
I can't figure out whether the ethernet cable from the main base station should go into the WAN or LAN ports on the back of the other base station. I've tried both and at the moment neither seem to be working.
Suggest that you connect the ethernet cable from one of the LAN <-> ports on your main AirPort Extreme (AEBS) to the WAN (circle icon) on the remote AEBS. You may need to refer to some settings on your main AEBS to configure the remote AEBS correctly.
To effectively "extend" the network that your main AEBS is creating, you would configure the remote AEBS as follows using AirPOrt Utility - Manual Setup
Click the Base Station tab below the icons to name your device, establish a device password and adjust Time Zone Settings
Click the Wireless tab
Wireless Mode = Create a wireless network (Not Extend as you might think because Extend is only used if you are connecting devices using wireless only. You are connecting using Ethernet)
Wireless Network Name = Exact same name as your main AEBS network
Radio Mode = Automatic
Radio Channel = Automatic
Wireless Security = Exact same setting as on your main AEBS
Wireless Password = Exact same password as your main AEBS network
Confirm Password
Click the Internet tab
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Click Update to save settings and you should be good to go. You have what is known as a "roaming" network because computers will automatically connect to the AEBS with the best signal as they "roam" around the building. The ethernet ports on the remote AEBS will be active as well in case you need to plug a device in at that location. Post back on any questions that you may have.
Message was edited by: Bob Timmons

Similar Messages

HT4889 Do I connect the two macs with the ethernet cable or do I have to connect both from the ethernet cable to the modem/router

Do I have to connect both macs directly with an ethernet cable without network connection to be able to transfer files/apps from the old to the new as I have tried migrating on the network without success.

They can be connected directly or via an existing network. Turn on File Sharing for the computer that will be sending files.
Using Migration Assistant will work best if the two computers are connected via Firewire cable. This assumes both computers have Firewire ports.

I have a AirPort Extreme Base Station with Gigabit Ethernet 802.11n ?

I have the 802.11n Airport Extreme Base it went bad so Apple Sent me a new one to put into my
office where I have a iMac 24" 2.4ghz with really fast internet
I also HAD a AirPort Express Base Station with 802.11g and AirTunes G not N so when I received the
new 802.11n Airport Extreme I sold the Airport Express 802.11g now my Macbook Pro 17" 2.33mhz
which is in my family room and that is also where the Airport Express with iTunes was located
now my internet is like really slow on the MBP 17" I have 5 bars in the pizza menu bar but my
internet speed is really BAD on the MBP 17" and I have 16mg speed on the net
+BIG ? DO I NEED TO BUY A 802.11n AirPort Express Base Station with 802.11n and AirTunes??????+
TO EXTEND THE RANGE OF MY AirPort Extreme Base Station with Gigabit Ethernet Which is in my
Office where my iMac 24" 2.4ghz is located and the internet zooms on the iMac but not my
my Macbook Pro 17"
Please help as I don't want to spend money on another 802.11n if it will not extend
I
Message was edited by: macman60

So you agree to the lose of the Airport Express removal has caused me to lose enough of a signal to make the Internet...
Sorry but I'm not sure what this long run-on sentence is trying to say.
You asked if the network could be wirelessly extended and that is what I replied to.

Problems Connecting to Airport Directly With an Ethernet Cable

Hello,
I have a Time Warner cable modem connected to an airport, and everything is working fine for a wireless web connection. But in order to log on to VPN for work, I need to have a cable connection, not a wireless one.
I turned off the airport connection on my computer and first I tried using an ethernet cable to connect my laptop to the Airport. That didn't work. Then I tried connecting my laptop directly to the cable modem, and that didn't work either.
I used to have a DSL modem in my apartment, and if I turned my airport connection off and plugged into the DSL modem, I was still able to access the internet no problem.
Is there something different about plugging into the airport or the cable modem? Do I need change any settings on my computer? Do I need to reboot my computer, or the airport or the cable modem or all three?
Any help is greatly appreciated.
Thanks,
Alice
iBook G4 Mac OS X (10.3.9)

Hi Alice,
I too have a Time Warner cable Modem and use a VPN with a Ethernet cable connected from my laptop to my Airport extreme. I did not switch ISP's but did switch hardware from a 2Wire portal to the Airport extreme. Could only access the internet and not connect to my Company's network via a VPN. Took a few days but I finally figured out a VPN solution using an ethernet cable hookup to Airport extreme from my work laptop. You will need port setting(s) from your IT department. Below are a few tips.
1) Open Airport Utility and double click on your extreme network.
2) At the top move from Airport and click on Internet.
3) Once there, click on NAT (Network Address Translation)
4) Check mark "enable default host" but use your static IP adapter address from your work PC/Laptop and not the default (use IPCONFIG to obtain)
5) Check mark "enable NAT port mapping protocol" and at bottom click on configure port mapping at bottom of NAT
6) From there your in the advance mode of your Airport Utility, and you add a
service and port(s). I did not click on any service but only defined using my company name and added the port settings.
7 I set the public TCP and UDP ports to 80
8) The private IP address matched the IP address in the Internet NAT setting I mentioned in #4 above.
8) The private TCP and UDP ports are the ports to open for your VPN which I got from my IT department. This can be a 5 digit number where mine starts with a 4.
The above worked for my ethernet connect from my work laptop to the Airport Extreme. I now can connect to my company's network using VPN and continue to work from home time to time. 8-)
Good Luck. My next step is to see if my work laptop can use the same settings for my VPN when I go wirelessly with my work Laptop.
Good Luck....Reener

Printer and AirPort Extreme Base Station with Gigabit Ethernet

Hello!
I own a macbook, one windows xp pc, and two windows vista notebooks. I bought a airport extreme base station. I set it up with my macbook at first and I do a print and it works. I do the same with the others. I install the printers drives to all notebooks. Then tried to print and only one of them worked. They all have bonjour download for windows. So i restarted all the pc's and mac and tried to print and never prints. On the pc's i get a error message. On the mac i get an its busy and never prints. All of them connect to the internet, but no printing. I have the printer connected to the base station. I did two prints and then I couldnt print after that. Internet works. Please i need some help to fix this. Thanks in advance

Hi
Maybe you already have fixed your printing problem. I'm no expert but I sometimes have had printing problems and I feel for you. However, first of all. What sort of printer do you have? It sounds to me that one of the pc printing documents got stuck somewhere on its way to the printer and now it is taking up space on the network (figuratively speaking ofcourse). I can recall something happening to my network/printer some years ago. Unfortunately I can not remember what I did to fix the problem but if I were you I would do the following: First I would disconnect the pc from the network and then try to reset the printer clearing its print memory. Then I would try to get the mac to print again. If succesfull I would take the mac off the network and connect one of the pc's and get that to print. If I succeded I would repeat the procedure with the other pc's. If I wasn't succesfull I would clear the memory again and then try with one of the other pc's. But I would only try one computer at the time to try to isolate the problem. Maybe you have already tried this and since pc's are a mystery to me I dont't know how to help you in that department. However using bonjour on the pc's I would not expect to have problems (though I use Windowc XP print menu on my vertual pc - works fine).
Hope that you will solve your problem soon.
Berit

Can I use the airport express as a repeater/range expander but without being connected to the modem with the ethernet cable?

I have a mac pro (2010 mid) to set up the airport

My 2003 Airport Extreme I guess does not provide this "enable extension of other Wireless Device" option in Airport Untility under "Wireless", because it is too old?
Correct. You will need one of the "square" AirPort Extreme versions if you want to do this.
Another question, do I need to buy a new Airport Extreme to be able to extend my Wi-Fi signal with the New Airport Express I just bought?
Yes, or another new AirPort Express. But, you cannot connect a hard drive to an AirPort Express. You can with an AirPort Extreme in case you were planning to add a hard drive.
One last question, I believe I understood that if I have the new Airport Extreme and use it with my Airport Express to extend the Wi-Fi Signal, I will be able to do this without my DSL Ethernet cable connected to the Airport Express?
The DSL cable will need to be connected to the AirPort that you designate as the "main" router on the network....assuming that you want to be able to connect to the Internet.
The other AirPort will connect using wireless only....assuming that it is located where it can get a good wireless signal.

Can one apple base be connected to another apple base station with ethernet?

Can one apple base be connected to another apple base station with ethernet?

Yes, it would be called a roaming network.
See the Roaming network here:
http://support.apple.com/kb/HT4260

Using Airport Extreme Base Station with Cable Modem

Hi everyone,
I have just bought an Airport Extreme Base Station. I connected it to my cable modem (Surfboard 3100) through the WAN port and my iMac G4 is connected to it through the Ethernet port. Installed the Airport Utility, and configured the base station with the normal settings of DHCP for Internet and DHCP for internal network.
After restarting the base station, my Internet connection from the iMac through the base station is very slow and most of the time will time-out. My Internet connection through my PowerBook G4 using wireless through the base station is ok though.
My question is, is there some setting which I should set for the Ethernet portion of the base station to make my wired connections to the Internet work?
Thanks in advance for any help!
regards,
Weiming
iMac G4 Mac OS X (10.4.10)

Hi,
My iMac G4 does not have an Airport card. I did not physically restarted the base station, its part of the sequence when we update the configuration, that the base station will restart on its own.
regards,
Weiming

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. Any tips on how to do this?

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

Problems setting up my TC. Have just bought new iMac(OS 10.6.8) and TC. I set it up. iMac cannot find it. I have tried direct connection with an ethernet cable to Mac or my wireless router but nothing. Just a flashing orange light. Help for a simpleton p

Problems setting up my TC. Have just bought new iMac(OS 10.6.8) and TC. I tried to set it up. iMac cannot find it. I have tried direct connection with an ethernet cable to Mac or direct to my wireless router but nothing. Just a flashing orange light. Help for a simpleton please. Have tried reseting TC, but to no avail.

Just updated from 10.6.7 ---> 10.6.8 and had the same issue. Despite having done a clean install from 10.6 and got everything back off my TC, now Time Machine can't find it!
Green light is on, ethernet cable conected, network CP says its conected but nothing. Airport Utility can't find it. Hit reset button, Orange flashing light but still no show in Airport Utility.
But I know its there, as rebooting from 10.6 SL disk shows the backups are still ok?
Hmm, ideas anyone?
SBB

Hi, I want to use my Capsule just as a back up via wireless. How do I set this up without connecting it with an ethernet cable to either a router or the iMac??

Hi, I want to use my Capsule just as a back up via wireless. How do I set this up without connecting it with an ethernet cable to either a router or the iMac??

I misunderstood what Time Capsule is and had hoped for a wireless backup device that didn't have to be connected to the router.
The TC is a wireless backup device.. it does not need to be connected to the main router..
The problem is the computer.. not the TC.. the computer has only one wireless card.. if your current internet is by wireless.. then you must choose.. internet or backup.
But my other suggestion will work.. get a wireless USB stick compatible with Mac OS.. there are plenty and cheap.. since you are in the same room as the TC they will work fine.. plug it in and load the driver.. taint hard.
You should do the first backup by ethernet though.. wireless is too slow.. once you have that, you will do fine.
Search ebay for wireless n usb.. Mac compatible..
http://www.ebay.com/itm/New-EDUP-Mini-Wireless-11N-300M-USB-LAN-Card-WiFi-Adapte r-Nano-Card-Soft-AP-/150864362939?pt=US_USB_Wi_Fi_Adapters_Dongles&hash=item2320 377dbb#ht_3553wt_1165
As you can see.. they are getting smaller and neater.
I have no idea if it works .. haven't tried one.. but I have used USB wireless stick on the Mac to overcome this issue.
You will need to set static IP .. not hard but you need to set specifics if you do buy one post again for the setup.

On my MacBook Pro when I am connected to the internet via an Ethernet cable, Facebook pictures do not load. They show up as white boxes with blue question marks.

On my new MacBook Pro when I am connected to the internet via an Ethernet cable, Facebook pictures do not load. They show up as white boxes with blue question marks. This also happens on a website editor. But, when I am connected to the internet via Wifi, everything load properly. This is my work computer, so I have to be able to connect through the Ethernet cable to access everything. Please help me!

I mostly use Safari. But I also tried it on Firefox, Mozilla, and Camino. Mac OS X. It's my work computer, so I've only tried it at the office. I have to be connected through the Ethernet cable to access my files and email on the server.

Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme..

Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme.

This will work.....IF....you also have an Apple AirPort router configured to provide your wireless network.
In other words, you need to have two Apple AirPort routers to extend a wireless network.
When the AirPort Extreme is configured to "extend" the wireless of the "main" AirPort, it will provide more wireless coverage and the Ethernet ports are enabled, so you could connect your Mac Pro to any of the Ethernet ports and use that as a network and Internet connection.

I have just get an apple tv but I could no configure my wifi, it does no appear any wifi name list, i connected it with an ethernet cable, but no with the wifi net, what sould i do

I have just bought an apple tv, I have tried several times to confiure the wifi but no success, the wifi nets list does not appear, I have connected with an ethernet cable but not with the wifi net...what can I do? is it normal? am I missing something?

Same thing here...Just bought it today, and only with the ethernet cable it worked...tryed to update it and now both wifi and ethernet won´t work...Any ideas?

HT1941 trying to connect time apsule to macbook air with the ethernet cable in the WAN port the airport utility doesn't detect it

trying to connect time capsule to macbook air with the ethernet cable in the WAN port but the airport utility doesn't detect it but when i put it in the LAN one it does but it doesn't let me configure
any ideas?

Isn't it fun trying to do things without an ethernet cable direct to the computer.. Apple sell a usb to ethernet adapter cable fairly cheap.. makes life a lot easier having something to do hard connections.. or as hard as usb can manage.
Since you have to access the TC by wireless .. press and hold the reset button on the TC for about 10sec until front led flashes rapidly.. don't worry about the ethernet cable.. leave it disconnected.
Now click on the airport symbol and join another network. The TC should revert to its home name.. which will be a combo of Time Capsule and its MAC address. There is no wireless security and you can do the setup.

Connecting to Base Stations with an ethernet cable

Similar Messages

Maybe you are looking for