Connecting to DVI monitor

I have a Pavilion h8xt, model h8-1160t.   I was getting Full screen movies, then all of a sudden all I get is Standard HD, and I have the same equipment.  (4 inch black screen on top of movie and on the bottom of movie.)  Some people I have talked with stated possible the HDCP 2.2?  I do not understand this, I am a novice for I do not understand what to do for it, I also am using Windows 7.
Now to the question:  Is it possible with the computer I have to get full screen again.  I have an ASUS screen - #PB278Q which has HDMI, VGA, DVI, and Display port. 
Anyway any help would be appreciated, as for other information I have also a brand new Note table 12.2 pro from samsung, same thing happened to it?  At the same time.  Thanks ahead of time.

Hi,
This probaly is due to the movie itself. Please note: the ratio of your monitor and your Samsung is 16:9 and many movies use different ratio (wider) therefore you can see two black bars one at the top and one at the bottom of your monitor and your Samsung. If you wish to watch full screen, you may cut left and right of the movie. More information:
    http://en.wikipedia.org/wiki/Aspect_ratio_%28image%29
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

  • MacBook Air mid-2013 OSX 10.9.1 cannot connect to DVI Monitor

    Does anyone else have this problem?  I've seen similar issues raised, but so far can't find a solution to my particular issue:
    MacBook Air Mid 2013 (ordered Jan 2014)
    - 1.3GHz Intel Core i5
    - 8GB 1600MHz DDR3 RAM
    - OSX 10.9.1 Mavericks.
    When I connect my MacBook Air to any monitor (well, I've tried three monitors: Benq, NEC and Samsung) the monitor will not detect an attached computer. The MacBook also does not think it's connected to an external display.
    If I connect via VGA cable, it works fine most of the time*, so the display port seems to work only for VGA and not DVI.
    I am using mini display port adapters (DVI and VGA) purchased from the Apple Store.
    The adapter for the mini display to DVI works fine, since I can get my 2009 MacBook unibody to connect to an external display via DVI without issue. So it's not the adapter, or the DVI cable.
    I have tried resetting the System Management Controller for my MacBook air but it does not work.  No matter how many times I reset the computer (Hard reset, Soft power down, SMC reset) I cannot get it to connect via DVI.
    Has anyone experienced this issue, or seen a resolution for it?
    *The only other symptom I get periodically, is that after being disconnected from a VGA monitor, the computer will periodically (about 2/5 times) not connect to the VGA monitor either without a reboot.   However it will connect most of the time, and ALL of the time after a reboot.
    Thank you

    Thanks themachead: I have tried the adaptors on different macs, as I indicated in my post.  The adaptor works fine with a different mac
    Yes, I have also tried starting up with the monitor connected, and disconnected.
    I just got off the phone with Apple Care. They couldn't solve my issue through normal means, but during one attempt, we closed my MacBook Air while it was connected to the external display, with my Magic Mouse and Apple Keyboard connected via Bluetooth.  The external monitor did not come on.  However when I opened my Macbook Air's screen, we saw that my Mac had crashed and prompted me to reboot. When it did, the external monitor worked.  I have been able to disconnect and reconnect the monitor and it seems to be working now.   I will see what happens after a few attempts.

  • 2 DVI monitors with G5 (1 ADC and 1 DVI port)

    I have 2 Apple monitors with DVI connectors and a G5 with 1 DVI and 1 ADC port.
    I have just bought a "DVI to ADC Adapter" but it looks backwards (for connecting an ADC monitor to a DVI port).
    What can I do?

    Hi-
    You need an ADC to DVI adapter, like this. The description is very dated, but, this is what is needed to connect a DVI monitor to an ADC graphics port. This is another one.
    So, you bought something like this?

  • IBook w/ Bookendz connector for DVI monitor?

    I have an iBook G4 and I'm using a bookendz hub to connect it to all my peripherals. I just got a 20-inch cinema display screen and it has a DVI connector -- but the bookends hub has a port for a VGA monitor. Is there any way I can get a cable to connect a DVI monitor to a VGA port? Or do I need to get a VGA monitor?
    iBook G4    

    See your other thread Bookendz and Cinema Screen.

  • Single DVI connection to DVI - DVI - Y cable hook up

    I have an HP Envy H8 1500 DT - with an AMD FX(tm)-6120- Six Core Processor  running WIN 8.1 - and thought I could connect two DVI monitors to my one DVI port on this machine by using a DVI Y Cable. Both monitors work with the cable but the option in preference - says it can't detect two monitors? Do I need another device/adapter?

    Hello cbriggs,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I understand you are trying to connect two monitors to your HP Envy h8-1500 Desktop PC. I am providing you with an HP Support document: Using Two or More Monitors with One Computer (Windows 8), which will walk you through setting up two monitors on your computer. Keep in mind the document is also for Windows 8.1 not just Windows 8.
    I hope I have answered your question to your satisfaction. Thank you for posting on the HP Forums. Have a great day!
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

  • Have DVI monitor - want to add VGA monitor - what adaptor am I needing?

    Well, Ii am at my office - not at home where my PowerMac is and I am wondering what adaptor I need to purchase in order to connect a second monitor to my G5?
    I am already using my DVI port for my 19" monitor.
    Surprise! When I tried to use my DVI - VGA adaptor (reaching behind desk scenario) it wouldn't work and I quickly realized, "Hey! That's not a DVI port :-|"
    What kind of port is it and where is the best place to get the adaptor?
    Thanks guys

    I don't think there are many companies making these, but there is no reason another brand shouldn't work. If you can't find an ADC to VGA adapter, you could buy an ADC to DVI adapter
    <http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wo/2.RSLID?mco= E1A673E1&nplm=T2774G%2FA> to connect your DVI monitor to the ADC port, and use your DVI to VGA adapter to connect your VGA monitor to the DVI port. Don't try an ADC to DVI followed by a DVI to VGA to connect the VGA monitor to the ADC port. ADC to DVI adapters may not pass through the analog signals needed by a VGA display.

  • Converting one of two DVI monitors to HDMI to view on HDTV

    Is this even possible?
    I have a DVI splitter already in place on the 2nd monitor but the DVI-to-HDMI converter next in the chain to the HDTV (1080p) keeps popping up the incompatible video signal message.
    Do I have to connect the optical audio line to make nice?

    Hi-
    The DVI splitter can only supply one resolution.
    Unless both monitors are of the same resolution, problems will result.
    Using both ports of the graphics card will give better results.
    If one port is ADC, use the ADC to DVI adapter (Belkin or Molex) to connect one DVI monitor,
    Use the DVI port to connect DVI to HDMI.
    Do I have to connect the optical audio line to make nice?
    No.
    You only need that to get audio.

  • What adaptor do I need to connect from mini display port to a dvi monitor

    I want to connect a 2nd monitor to my mac mini via the mini display port, will the Apple adator do this ok or will I need an active adaptor

    I had trouble with different Mini DisplayPort to DVI adapters, including a couple of Apple branded ones.
    When I mentioned the problem to the Apple rep. at Fry's. He walked straight over to the rack, handed me a > Kanex Mini DisplayPort to DVI-D Adaper grined and said, I've never had one of these baby's come back.
    After that my 2010 Mac Mini has been very stable running Dual 21.5" Samsung DVI monitors. One in on the Apple Supplied HDMI to DVI adapter, the other now on the Kanex Adapter has been rock solid for over a year.

  • Is anyone else experiencing problems with the thunderbolt port on their Mac Mini's regarding using it to connect a second monitor? I've got the Mini Display Port to DVI-D adapter along with a DVI-D cable and I can't get an image on the second monitor.

    I had an dual display image / setup working twice for a few seconds, but then it cut out. I think there may be a problem with the thunderbolt port.

    As far as I can tell you have only listed that you have a DVI monitor connected to the Mini Displayport socket (i.e. the Thunderbolt socket) via presumably the Apple Mini Displayport to DVI adapter and a DVI to DVI cable.
    You don't appear to have listed what the second monitor is and how it is connected (even though not working). As such I cannot tell what may be wrong.

  • DVI connection to second monitor doesn't work

    When I had the connection from my Mac Pro to my two monitors (20" Cinema display and 19" Princeton monitor), I had the black screens for a few seconds for both monitors then return to normal. It happens anytime. I read the forum and changed the VGA cable to connect the 19" Princeton monitor and now both monitors work fine.
    Do I have to live with the VGA cable option or anyone know how to utilize the DVI connection capability of Mac Pro please help?
    Mac Pro   Mac OS X (10.4.8)   2.66 GHz, 20" Cinema Display, 19" Princeton Monitor

    Hi Joe,
    I tried to locate the right slot (x16) by going to
    Expansion Slot Utility and changed from #1 to #2. It
    showed my configuration of the PCI card now is x16 or
    fully speed.
    The problem is still the same with DVI connection to
    two monitors. Any other suggestions would be
    appreciated.
    Mac Pro
    Mac OS X (10.4.8) 2.66 GHz, 20" Cinema Display,
    19" Princeton Monitor
    I'm fresh out of idea's. I assume that your card is a 7300GT, correct? I had an out of the box failure with mine and Apple replaced it. I was lead to believe that there were quite a few failures with the card. Interesting, they didn't even want the old one back.
    I'd go the Applecare route next and see what they say. FYI, I have two of these running three monitors (all apple flat panels) all on DVI connectors.
    Joe

  • Can I use the Apple VGA to DVI adapter to connect a PC to a DVI monitor?

    Hi
    Any idea of the Apple VGA to DVI adapter would work to connect a PC's VGA output to a DVI monitor?
    Is it a simple pass through?  Or are there drivers needed.

    That adapter is for connecting a VGA display to a computer's DVI-I port.  A DVI-I port has both digital and analog video pins.  The adapter passes just the analog video to a VGA connector.  It will not work in the reverse direction because a VGA computer does not provide digital video.
    There are VGA to DVI converters that will connect a DVI display to a VGA computer.
    <http://www.monoprice.com/Product?c_id=101&cp_id=10114&cs_id=1011401&p_id=8214&se q=1&format=2>
    <http://www.aten.com/products/Professional-Audio/Video/Converters/VGA-to-DVI-Conv erter~VC160A.html>
    No drivers needed.

  • Connecting two Acer monitors with VGA and DVI output to my Macbook Pro (mid 2010)

    Hi All,
    I need to connect 2 Acer monitors that have both VGA and DVI ports to my MacBook Pro.  What's the best way to do that?
    Thanks for your help!

    hey! Thats normal for notebook! That actually happens to almost all of us - as there are a small fraction of people with two and more thunderbolt displays or with newest rMBP and external multi-monitor setup.

  • Connecting DVI Monitor to the ADC port

    I have a G5 with dual video ports. One is an ADC Port and the other is a DVI port. I want to get rid of my Apple display and connect two Dell monitors both of which have a DVI connectors. How do I connect a DVI connector to the ADC port? The DVI to ADC adapter is for connecting a ADC Apple display to a DVI port. Is there an adapter for doing the opposite--a DVI plug to a ADC port?
    Power Mac G5   Mac OS X (10.4.9)  

    The ADC to DVI adapter is for connecting a DVI LCD to the ADC port. It cannot be used with a DVI to VGA adapter to connect a VGA display to an ADC port. For that you need an ADC to VGA adapter, such as:
    <http://www.mac-pro.com/s.nl/it.A/id.230/.f?sc=2&category=128>
    These are becoming scarce as the ADC is no longer being manufactured.
    Your Sun monitor should work from the ADC port using the ADC to DVI adapter, and the Fujitsu from the DVI port using the DVI to VGA adapter.

  • Portege R500: cannot connect the remote DVI monitor via Dynadock

    Hello,
    I just connected Dynadock (DVI) with my Portege R500. The notebook would be supported -- according to Toshiba -- but my experiment confirms that Dynadock is not able to access DVI port. This implies, that Dynadock is nothing more than USB HUB.
    My setup: Vista 32b Business (CZE edition), latest fixes, Toshiba R500.
    Software: latest dynadock software 2.3c.
    Symptom: I cannot connect to the remote DVI monitor via the dynadock, only two external panels with 800x600 are available, but Vista does not allow me to choose them.
    More info: Dynadock Software requires to run without Microsoft Defender, else it blocks service:DisplayLinkService; file:C:\Program Files\DisplayLink Core Software\DisplayLinkService.exe
    If you disable MSDef, the message "error 2738" appears when you connect the dynadock and when Vista tries to install a missing drivers for you.
    Yes, I do know the VBS issue, and the problem is not caused by VisualBasic -- VBS "Hello World" runs.
    If you still believe, that Toshiba Dynadock is compatible with Toshiba R500, then press Fn-F5 and peek at your logs and you must find something like:
    In English: igfxext.exe throws an exception 0xc000000d, offset 0x0000f9f8.
    I welcome any comments, hints etc. If you are able to pass this bug report to a responsible engineer, do so please.

    Hello again Leo
    I still believe you are wrong. Toshiba Dynadock is not designed for Toshiba products only. It is universal product and can be used on every notebook. To be honest I believe it is better to use it with new, more powerful, notebooks.
    When you sat your notebook model is listed as compatible I believe you. Why not? Toshiba can list all newer notebooks. No problem at all. To be honest I am also interested to buy Dynadock but after reading your posting I wanted to see how it works exactly.
    I have contacted my friend because he works in one big electronic store and I was lucky because he had Portege M500 too.
    He was very nice and offered me to test Portege M500 SSD model with Dynadck PA3542EY1PRP. I hope you have the same model. It is DVI model. So I have done follow:
    - Portege was preinstalled with clean Vista OS (factory settings started for the first time)
    - I have installed latest Dynadock Utilitiy for Vista 2.3c
    - Installing this software you must pay attention about installations steps and the installations procedure should not be interrupted
    at one step there is window Installation Complete but it is not complete and must be continued with
    Display Link Core Software installation
    Video Dock installation
    at this point the Dynadock must be connected to favorite USB port NOT FROM THE BEGINNING
    - At the end I have restarted notebook
    The installation was finished properly and I have connected 20 Toshiba Tekbright LCD display (DVI cable). The native resolution is 1680x1050. in Display properties there are shown three displays. Display number 3 belongs to display connected to the Dynadock.
    Resolution 1680x1050 was there and display shows perfect picture. I have tested it as extended desktop and it works without problems. I didnt test it playing some movies.
    I have also tested it with FN+F5 key combination. It does not work as it should be but there is definitely no error message. I know that FN+F5 key combination is not designed for external graphic card and I know that it can not work well.
    At the end I can sat that Dynadock works well with Portege M500 SSD and there is definitely no error message. It works with Vista very well. I have tested it with screen saver and with few restarts. Nothing changes. Everything was OK.
    So after this test I can say that you have done some mistake. If you want to use it again I recommend you to install Vista again using recovery image. After doing this you will have clean preinstalled OS. Install software but please follow the menu on the screen and be sure all three components are installed properly. If I am remembering well when you see message about USB audio device installation you must connect Dynadock and continue installation.
    PLEASE FOE DYNADOCK USE ALWAYS THE SAME USB PORT!!!
    Sorry for this long story but I can say for sure IT WORKS PROPERLY!!!
    Have a nice day!

  • Lost the monitor after connecting via DVI

    I've had an X2Gen 22" monitor connected to our G5 via DVI/VGA adapter to the VGA input on the monitor for a couple of years. Another monitor I just bought came with a DVI cord and a VGA cord. I decided to try the X2Gen/G5 connection via DVI since I now have a cable. The computer can't/won't recognize the monitor now that they're DVI connected. And screen images are ugly! I can't even calibrate it because the computer tells me it cannot identify the monitor. Any ideas anyone? (Other than going back to the VGA cable?)
    Thanks,
    Jon

    Just a thought, but try zapping the PRAM. Good luck.

Maybe you are looking for