Connecting to guest network with iPhone ios5

After upgrading to iOS 5 my iPhone doesn´t work on the guest network on my Time Capsule (It connects, but internet won´t work). The reason seems to be that the assigned IP is not in the range defined for the guest network (but rather in the ip-range for my main network). Both my Macs and ipads get the right ip-address. I`ve tried this with 3 different iphones.
All phones worked on the guest network before upgrading, and still works when I connect to my main wi-fi network.

Did you perform a full power cycle and reset of your modem as follows?
Push the reset button on the modem
Power off the modem
Pull the battery if it is easily accessible
Power down all other devices on your network, order is not important
Wait 30 minutes ( It sometimes takes even longer for the equipment back at the cable company to fully reset so that it will issue you a totally new fresh connection. The cable company will never admit this.)
Reinstall the battery if you pulled it from the modem
Power up the modem and let it run by itself for 3-4 minutes
Start up the AirPort Extreme and let it run for 3-4 minutes so that it will fully associate with the modem
Start each device up on the network one at a time about a minute apart
Check for operation.

Similar Messages

  • Cannot connect to home network with iphone via wireless.

    wireless home network does not appear in iphone. pc, laptops and iTV work perfect with wireless. I tried everything i can think of. anysuggestions?

    If there is no problem with the iPhone seeing any other available wi-fi networks or connecting with any other wi-fi network your iPhone has access to, not sure how it can't be a problem with your wireless router or network regardless if the iPad and iMac have no problem.
    No change after resetting network settings on the iPhone and/or after restoring the iPhone with iTunes as a new iPhone or not from the backup.

  • Guest Networking with Time Capsule - bridge mode?

    Hi, hopefully someone can help.
    I'm trying to set up guest networking with my time capsule but it's currently set up in bridge mode so it wont let me.
    When I try it in public IP address mode it says 'The DHCP range you have entered conflicts with the WAN IP address of your Airport wireless device'
    I'm completely new to networking and have no idea what most of these terms mean, despite googling them all!
    Can anyone advise on what I need to do to get it all set up?
    Thanks in advance, any help much appreciated!!
    Andy

    Is there no way I could switch off part of the router so it just becomes a modem (or are they completely different things)?
    It might be possible to convert the gateway to function as a simple bridge only modem, but that would involve checking with the support folks for the device. I doubt that your service provider will provide any assistance with this, because they will likely claim that this type of configuration is not supported.
    So, look to see who actually manufactured the device and check with their online forum or support site to see if the conversion to a simple bridge only modem is possible.
    You don't indicate whether you have cable of DSL service, and that will of course affect things as well. If you need to go to a simple modem, the best choice is always a device offered by your service provider, so that you will be supported in the event of Internet connection difficulties.
    If you try an off-the-shelf modem and have any problems, your service provider will offer little or no support. Often, you can get a free modem from your provider in return for a commitment of a year's service. Might be worth checking that out.

  • I have a RCA media streamer that will not connect to my network with a new airport extreme.

    I have a RCA media streamer (Model # DSB872WR)  that will not connect to my network with a new airport extreme.I had to create a new network and  my computers are connected but media streamer will not. Can anyone help? Thank you

    Hi, papineaubill!
    Welcome to The Canon Forums, and thank you for your inquiry!
    We appreciate your participation, though we need to let you know that the Canon Forum is hosted and moderated within the United States by Canon USA. We are only able to provide support for Canon products manufactured for and used within the US market.  If you live outside the United States, please click here and select your country or region for your support needs.
    Feel free to discuss Canon products sold outside of the United States, but please be aware that you will not receive support directly from Canon USA.
    Thanks for choosing Canon!

  • Connecting Wahoo Blue HR with iPhone 5 does not work, tried everything possible

    Connecting Wahoo Blue HR with iPhone 5 does not work, tried everything what I could find in the interenet as solution??????

    IPhone 4s, iOS 7.1.1: iphone can't connect to wahoo HR BT4.0 sensor :((( Wverything worked fine with iOS 6 !!!

  • When synchronising photos with iphone ios5 get 2 folders with same photos on iphone? sollution?

    Hello,
    When i try synchronising photos with iphone ios5  i get 2 folders with the same photos on the iphone?
    Does annyone know how to resolve this?

    Idd,
    when i look at the albums, i see filmrol (where the photo's i take with my ipone get placed) and i also see photo library and the name of the folder i am syncing. is there a way to view only one of them?
    THX already for your help.

  • With new OS6 I can't connect to wifi network with my iPhone

    Ever since I upgraded to the new iOS6, my phone will no longer connect to my wifi networks. It only works on 3G. Tried to reset networks and various other things to no avail. Not happy ...

    Hello,
    I tried the Apple Support recommendation but nothing works, my Ipad mini still can't connect to wifi network, the wifi function in the setting menu it's not available.
    I would like to send my device for technical support in USA. I'm live in Venezuela.
    How can I do it?
    Thank in advance

  • I cannot connect to guest network.

    Hi
    My Guest network looks OK inTC, but just hangs when I try to access it from my iPhone.
    Also my TC screen seems 'blocky' when redrawing and there is no screen with stars!
    I'm on Yosemite with a new TC and a new iMac 27"
    Please can anyone help? Ive rest the system about 6 times but no difference....!
    Stuart

    I have a cable feed to the property into the cable company's router. From there, a network cable into the TC, and then a feed from the TC to the iMac.
    That means the TC is in bridge mode and you cannot use guest wireless.. it looks like you can but it actually will not work. Therefore the iphone must connect to the main wireless network.. OR if your cable router is wireless .. most are.. use that for guest wireless network.
    As I said, the computer is wired in- my printer is wireless.
    But your iphone is using wireless. Only you cannot use guest in your setup.. so use wireless as explained above.
    There is a big issue now between Yosemite, iOS 8 and the Airport router.
    See the background to this here.
    Problems in wireless with yosemite.
    AWDL
    https://discussions.apple.com/thread/6693499
    http://help.apple.com/deployment/ios/#/apd8fc751f59
    For that reason I want you to stop the TC from being able to swap channel at 2.4ghz.. whenever it wants to..
    The setting is under wireless options.
    Change from Automatic, to 11, 8 or 6, in that order.. as they tend to be less used.. 1 and 6 actually are the most overused.
    In my previous iMac and TC , the "enter time machine' instruction had a black space background. The current one is blobs of blurred colour which goes into blocky squares when I move the mouse over it.
    Ahh.. I see. I will have to boot my one computer that runs yosemite.. I have been keeping it turned off as it causes network havoc.
    I might get Bob to comment as he is running Yosemite as main OS now.. and it might be plain sailing for him.

  • Using an airport extreme in both bridged mode and guest network with DHCP

    I currently use a third-generation airport extreme in bridge mode to connect my various Mac servers To the Internet. I'm using bridge mode on the AirPort Extreme because I have up to five static IP address (only using three now) I am currently not using the wireless network, and none of the servers are serving DHCP. I am looking at the Newer airport extreme with guest network Wi-Fi. My question is, does the new airport extreme base station support bridge- mode for any devices and host DHCP for the guest network connecting wirelessly to the base station?

    The AirPort Extreme cannot be in Bridge Mode and support a Guest Network.
    The AirPort must be configured to provide DHCP and NAT services if you want to enable the Guest Network function.
    If you really do have a 3rd Gen AirPort Extreme, it will support the Guest Network feature if you connect the AirPort directly to a simple modem.....not a modem/router or gateway type of devices.......and configure the AirPort to provide DHCP and NAT services for the network.

  • Guest network with WAP321

    Hello everyone.
    My client has a WAP321 Wireless N  POE AP.   It is connected to  port g0/2 on an ESW-520-24 cisco switch.  I have a Cisco 5505 firewall with an unlimited user base license.   Is it possible to setup a guest network that is on a different subnet than my internal LAN. If so can someone please direct me to doing so.
    Thanks

    Hello,
    I believe what you are describing is possible, although it will mostly come down to configuration on the ASA.  I know you mentioned you have an unlimited users license, but do you also have trunking in your license?  By default the 5505 only allows three VLANs, and they are used in a way that there isn't an extra one for you to use unless you have the Security Plus license (which raises your VLAN limit to 20).
    You may be able to get around this by configuring the ESW to run in Layer 3 mode, and have it do all of the routing between the two VLANs, however there would still be quite a bit of config to be done on the ASA to get it to NAT and route for the VLANs behind it.
    I can't really offer too much assistance on the ASA, since it isn't a Small Business device, so you may need to speak to TAC about setting that up.  However we can help setup the ESW to handle multiple VLANs, but I would check on your ASA before we move forward with that.
    As for the AP, it is capable of multiple SSIDs on different VLANs, and on the ESW you would configure a trunk port going to the AP to pass both VLANs to it, but again I'd advise against doing any of that until you find out how/if your ASA will be able to handle multiple VLANs.
    Hope that helps point you in the right direction,
    Christopher Ebert - Advanced Network Support Engineer
    Cisco Small Business Support Center
    *please rate helpful posts*

  • Can not connect to wireless networks with ipad 2

    My ipad used to connect to the wireless net at home and in public areas.
    Now all by the sudden it can't "see"  the network.
    Message: " could not connect to wireless network"
    I have tried "everything" also on different networks,
    except resetting the modem.
    My iPhone works, as do all my other computers.
    Modem is Zyxel P2812

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130?tstart=60
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • HT204409 Cannot connect to home wifi with iPhone 4s.

    IMy iphone does not see my home wifi.  Nothing has changed, even after IOS 6.  My Ipad and iMAC see and connect just fine.  I reset everything on the modem and computers and again everything connects except the 4S.  I have verified and or reset all settings including no security.  It sees all the other netowrks in the area too.  Any suggestion.
    BKV

    If there is no problem with the iPhone seeing any other available wi-fi networks or connecting with any other wi-fi network your iPhone has access to, not sure how it can't be a problem with your wireless router or network regardless if the iPad and iMac have no problem.
    No change after resetting network settings on the iPhone and/or after restoring the iPhone with iTunes as a new iPhone or not from the backup.

  • Setup Guest Network with OS X Server and Airport Extreme - NEED HELP!

    Hi All,
    So I have a small business with a Mac Mini Server (10.6.5) and an Airport Extreme. The Airport is handling the routing and DHCP duties, while the Server is handling the DNS. The Airport is pointed to pull DNS from the Server. All internal systems work great accessing the internet and folders on the Server.
    I need to setup a Guest network for internet access, so I turned this function on in the Airport Extreme. It sets up fine, but if you connect to that new Guest Network the system hangs trying to open a web page. My thinking is since the Server is the one handling the DNS it is not working for Guest computers since they are not part of our internal network. At least that is my theory, I could be wrong.
    With this type of setup what do I need to modify to get this working? Anyone have any ideas?

    After trying for days to figure this out I was finally able to get a working solution and I now have my APE providing a guest and main network while using my lion server as the Dsn server for the main network.
    The setup is a bit of a hack and does require you to have at least two devices with staticly assigned ip information on the main network but it does allow you to serve dhcp for both networks from the server and make some services available to the guest network such as iTunes remote for parties.
    1) delete your custom Dns entries from the Internet settings in the APE and set two dhcp reservations for .2 and .3 (in this case my Mac mini server and my airport express)
    2) reduce the dhcp range to only have 2 available IPs (10.0.1.2-10.0.1.3) and save settings
    3) on a computer connected to the main network install wireshark and begin sniffing for packets. Connect at least one device to your guest network and look for any packets that have an ip from your guest network (usually 172.16.42.x) once you capture one of these packets expand the vlan information. This should list a vlan ID ( in my case this was 1003. I would suspect this is universal but do not know)
    4) on your server open network preferences, click the gear at the bottom and click "manage virtual interfaces", add a vlan that matches the vlan ID from above. Click ok and apply your settings. The vlan interface should get an ip in the guest network range from your APE.
    * if you are running lion you will need to install server admin tools before proceeding*
    5) open server admin and add the dhcp service. Create an entry for your primary network (ex: 10.0.1.x) make the dhcp range one higher than the settings in step 2 ( ie: 10.0.1.4 to 10.0.1.253) assign this to the physical interface. Make sure this entry has your internal DNA servers
    6) add another entry for the guest networks ip range (ex: 172.16.42.x) again set it one ip higher than step 2 ( 172.16.42.4 to 172.16.42.253) save and activate both ranges. Assign this range to the vlan interface. Make sure this entry either contains your isps dns servers or another public dns server. Turn on dhcp.
    Because you have now assigned the only two addresses in the APEs pool for your primary network to static entries there will not be any addresses to assign and the APE will not respond to requests. This will allow your server to pick up the work of assigning IPs. As for your guest network, the APE will assign IPs for two host and then stop. Your clients may either get an IP from the APE or the osx server so both should have the same info. Just make sure the two static clients on your main network have the local DNA servers entered manually.

  • Slow wifi network with iPhone

    I have a latest model 16GB iPhone and am seeing extremely slow internet speeds over my home wifi network. Some of my friends are having the same problem.
    I have a fairly modern ethernet-only ADSL2+ belkin router, which is connected to my time capsule. I'm using my time capsule to provide wireless internet access. There are two macs on the network with 802.11n cards, and a third mac with 802.11g, as well as my iPhone. I also have an airport express (i'm fairly sure it also has 802.11n) which is used exclusively for printing.
    When I run a broadband speed test, I get 4 to 5Mbit on the mac with 802.11g. But on my iPhone I'm only seeing speeds of around 0.5Mbit!
    Does anyone have any ideas what is going on?
    Message was edited by: Abhi Beckert

    Hi imobl,
    Im having the same issue as virkdaman even after I updated to iOS 6.0.2. The Wifi network gets disconected frequently even when I use home wifi while my iMac is connecting to home wifi with no issue. My Iphone5 has never been jailbroken. Is it I have to wait for another iOs update to get this issue fixed?
    Thanks

  • Can't connect to wireless network with "conflicting" essid

    Hello,
    My wireless card works perfectly (actually I am using ndiswrapper, but anyway) on Arch and I can connect to my home wireless network. I use iwconfig to connect.
    In my office we have a wireless network. It's essid is "default" and it uses WEP. I can connect to it using Windows, but not using Arch. Im running the following commands:
    iwconfig wlan0 essid "default" key XXXXXXXXXX
    dhcpcd wlan0
    and it doesn't connect ("waiting for carrier..." and nothing happens)
    I guess the problem is that there is another network with the same essid - "default". I've tried to manually associate my card with my office network AP using iwconfig wlan0 ap XX:XX:XX:XX:XX, but it didn't work either.
    What should I do?

    What kind of Wireless card do you have and what does it say when you do a lspci? So for me, I know I have a Broadcom and the way I found it was to do:
    lspci | grep BCM4312 (or whatever wireless make/model you have)
    or
    lspci | grep "Network Controller"
    The second option should also get it for you. From there, you can check out this list to see if that might help you with drivers (but then again, you might have known this already so...).
    Hope this helps.
    Last edited by ruffedgz (2009-11-23 21:03:42)

Maybe you are looking for