Connecting to iTouch via "Connect to server"

Can I access an iTouch 1st gen with wireless (local network) connection (Finder>Go>Connect to server)?
I have file sharing on (AFP) and I've followed the instruction provided by the App developer but the error message "Connection Failed - - There was an error connecting to the server 10.0.1.4 Check name, IP. . . " is returned.
I've checked the IP address, I'm using the "listed port :4242" in the server address.
The iTouch app in question was using Bonjour until it's recent upgrade, but that doesn't seem to be the case any more?? (not sure why it's not but......?).
I'm able to access other functions via bonjour and the wireless between these two devices.
The iTouch OS is 3.1.3 I'm trying to connect via a Time Capsule / Air port router to a OSX 10.6.3 Mac Pro.
I'm able to access other functions via bonjour and the wireless between these two devices.
Thanks for and help insight.

This problem was in the bad parameter type,
that I was set to the insert statement.
No correct error handling from ORACLE in this case.
(No error messages, hanging HSODBC)
P.

Similar Messages

Lion 10.7.5 cant connect to printer via Buffalo print server

Hi everyone,
I'm at my wits end with this one having spent over 20 hours on it.
I have a Macbook Air running Lion 10.7.5 and a Macbook running OSX 10.6.8. I have a Photosmart 8050 printer attached to a Buffalo Linkstation Live LS-CH1 running firmware 1.60 (the latest version for this model). The Linkstation has a printserver which is attached via USB to the printer, the Linkstation is attached to a wireless router, for amound other things, wireless printing.
The long and the short of my problem is, I can get the Macbook running 10.6.8 to print without a problem, works fantastic, but I can not get the Air running 10.7.5 to print through the print server even though the printers are installed the very same way on both machines. The error from the print que is "unable to connect to printer" even though it seems to connect successfully to the Linkstation, as in my setup a username and password must be entered to access the printer, even though a user is logged in to the file server. Not to get confused, I am 99% convinced the problem is with the Macbook Air running 10.7.5.
I installed the printers using the Windows method, Workgroup -> Linkstation -> Printer then selecting the HP 8000 series driver version 5.0.4. I have also tried every other install method available, however as I understand it, this is the recommended method for this print server setup.
I have checked the network setup, driver versions and even though it does not seem to cover my printer have GutenPrint 5.2.9 installed.
The printer does work when connected directly to USB however.
If anyone has any idea why I cant get the Macbook Air running 10.7.5 to print via the print server on the Linkstation when 10.6.8 works perfectly, then please HELP!
Thank you

Power Cycle
Power off the router. Unplug it from the wall. Wait for few minutes.
Connect the router back to to the wall.
Power the router back on. Wait until all lights are lit properly. It will take a while.
Restart the computer.
Start up in Safe Mode.
http://support.apple.com/kb/HT1455

Can't connect to printer via usb print server

So I've tried to connect to an EPSON stylus printer from my iMac via a print server with no success.
Here's some info to help focus the questions/help:
iMac running Mavericks, Epson SP R200 printer, Belkin Play router, Toshiba Satellite laptop, Level1 USB print server
Win8.1 laptop prints via print server just fineso IP, port, firewall issues on router/print server side are ruled out.
I have the fire wall off on the iMac
I've quadruple checked IP and subnet numbers of iMac to rest of network, and they all jive.
I can pull up the config page of the print server via Safari on the iMacso connectivity is there
I previously had the printer attached directly to the iMac, and successfully printed.
I've tried to add the printer via IP > LPD method AND Advanced > Windows printer via spoolss
I can get as far as adding the printer, but as soon as I attempt to print a test page the printer has a "filter" error, or some "color" error, the job just goes into nothingness, or the job just sits there and the que is paused.
This is very frustrating to put it nicely.
-Vince

What driver are you using? - Don't know if you remember, but you had to be using Gutenprint, because Epson's driver for USB-only printers, only works via USB.
http://gimp-print.sourceforge.net/MacOSX.php

Unable to connect to Essbase via EAS after server re-ip

Hi all,
One of our environments have had the servers moved to new IP addresses. The DB server was completed changed so I had to reconfigure the environment, using the same databases, and redeployed all the components. Everything worked apart from EAS. It would not launch from the URL nor would it work if the console was installed on a server or PC. I logged an SR and it was suggested to update java which I did but it made no difference. A remote session yielded nothing. I decided to uninstall EAS and reinstall it dropping the tables in the DB and having them recreated as we use calc man for Planning. The EAS console now launches but I can't connect to Essbase. It just hangs and complains of an invalid log in. I tried the native admin account but that made no difference. Here is an extract of the logs
easserver.log
[2013-11-06T15:29:02.482+00:00] [EssbaseAdminServices0] [ERROR] [ESSEAS-35505] [oracle.epm.essbase.eas] [tid: 19] [userId: <anonymous>] [ecid: 0000K8i1zGFAtH_5HRL6if1IUYLA00001b,0] [APP: EAS#11.1.2.0] Following Exception occurred for user admin. Message exception is EPMCSS-00301: Failed to authenticate user. Invalid credentials. Enter valid credentials.
EssbaseAdminServices
####<Nov 6, 2013 10:50:44 AM GMT> <Error> <Diagnostics> <THE SERVER NAME> <EssbaseAdminServices0> <[ACTIVE] ExecuteThread: '55' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1383735044140> <BEA-320127> <An error occurred while generating Image Source configuration as part of the diagnostic image zip file:
weblogic.diagnostics.image.ImageSourceCreationException: java.lang.NullPointerException
at weblogic.management.provider.internal.ConfigImageSource.createDiagnosticImage(ConfigImageSource.java:105)
at weblogic.diagnostics.image.ImageSourceWork.run(ImageSourceWork.java:111)
at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTuningWorkManagerImpl.java:528)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:176)
Caused By: java.lang.NullPointerException
at weblogic.management.provider.internal.EditAccessImpl.getEditor(EditAccessImpl.java:597)
at weblogic.management.provider.internal.ConfigImageSource.writeEditLockState(ConfigImageSource.java:296)
at weblogic.management.provider.internal.ConfigImageSource.createDiagnosticImage(ConfigImageSource.java:88)
at weblogic.diagnostics.image.ImageSourceWork.run(ImageSourceWork.java:111)
at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTuningWorkManagerImpl.java:528)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:207)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:176)
>
EAS is installed on the same server as Planning, APS, RA etc. essbase is on a separate box as are the sql databases so in all 3 servers for this environment.
Essbase is definitely started as I can connect to it using EAS from another environment and retrieve database from the apps in excel.
Thanks in advance,
Nathan

If you are able to connect to Essbase using EAS from another Server or PC. and in that Server only if you not able to connect to Essbase using EAS
it is Java issue only. (Ensure ESSBASE.EXE process is there in Essbase Server)
Which version of Hyyperion you are using??
Uninstall Java and install again.
Thanks,
Mady

Connected to internet via ethernet but server not responding

I have browsed some threads on this topic but none gave me an answer, and my set up is not quite the same as those that I've read. I don't want to hijack another thread and confuse the readers. I would be very grateful for help on this issue.
I have connected a G3 imac to a G5 imac with ethernet cable and both are configured for file sharing following the instrauctions on this help site. Both machines communicate and file sharing is okay.
Now I want to share the dial-up internet connection of the G3 with G5 over this ethernet connection. I have configured both machines following instructions on this site. At the moment file and web sharing is enabled on both machines.
In sharing preferences/internet internet sharing is turned on on the host (the one connected to the internet)
In sharing/firewall personal web-sharing is checked on both machines
In built-in-ethernet/TCP/IP config IPv4 is off on both, although i have tried it with IPv4 set to using DHCP on the host, and then on both
No proxies are set
I have tried it with Appletalk both on and off on both machines
In network status internal modem is at the top of the list on the host and ethernet is at the top on the guest and both say that they are connected to the internet. The ethernet appears as connected to the internet with green light even when the host computer is not connected to the internet.
Yesterday I was able to browse using IE in windows XP running on virtual PC on the guest (G5) but this is the only time it's worked and I don't know what i did for that to happen. I only wanted to run a software activation on the G5 but the message unable to establish a connection appears.
I followed the help in virtual PC to share the Macs internet connection with windows, but havn't been able to connect to internet using the browsers on the OS X system. Tried altering browser preferences as well with no joy.
Everything works fine on the G3
I don't know where to go next.
imac G5 Mac OS X (10.4.3)

Teecee,
You may want to re-post this is the "Internet, Networking and your iMac G5" Forums to get more relevant and better informed answers as pertaining to your issue and your particular model.
Here is the link to that area of the discussions:
http://discussions.apple.com/forum.jspa?forumID=880
This forum is for "Using your iMac (early 2006)" models (or Intel CD) and this venue may not quite provide the insight and background you need for your specific model and problem.
Hope you get the help you need there...

Connect document libraries via connections

Hi,
I need to connect two (or more) document libraries using 'Connections'.
I created a new page.
Added 2 document libraries.
I want the user to be able select a customerid in document library 1 (Customer)
I want to use the customerid selected in document library 1 as a filter for document library 2 (customer details).
Problem: I do not see the connections option on a document library.
Any ideas?
Thnx!
I want to the following for document libraries:
http://www.youtube.com/watch?v=HR6WolyHv2Q

Hi,
Which permission did you use? I had check again with only edit permission, the connections option worked well.
Did you check with other pages? You can create a new page, then check whether it works.
Did you use the compatibility mode or add the site into trusted sites?
You can use compatibility mode to check whether it works.
Open IE->Tools->Compatibility View Settings
You can also add the site into Trusted sites.
Open the IE->Internet Options->Security->Sites->add the site into the Websites, then check whether it works.
What's more, you can use other browsers to check whether it works, such as Firefox, Chrome.
Thanks & Regards,
Jason
Jason Guo
TechNet Community Support

Unable to connect to Internet via Airport Express - 'cannot contact server'

I'm unable to connect to the internet via my Airport Express. I'm using OS 10.3.9, and had the same setup with no problems at a previous address, but with a different modem from the same ISP.
My AE is connected - the light is green - and my mac is connected to the network in Internet Connect. But when I open Safari I get an 'unable to contact server' message.
I've tried rebooting everything (modem, AE, Mac), and leaving modem/AE off for several minutes. Also reset the AE, but to no avail.
The connection works fine via Ethernet cable.
Any ideas?

Thanks, I checked out that advice doc (106798), but could not connect to the address (http://17.149.160.49) which is given to test if it's a DNS issue. My ISP says I shouldn't need DNS settings.
The service is PPPoE, and I went into Airport Admin Utility to check if the Airport was configured for this. Under Configure/Internet, I found it was set to 'Ethernet', so changed it to PPPoE. Then when I restarted I got connection status in the bar (and good Airport signal), but status flipped between 'looking for PPPoE host' and 'negotiating PPPoE host', sometimes sticking on one or the other each time I tried rebooting all gear.
Any other ideas?

Connecting to a cube via a linked server

Hi
I want to connect to a SSAS cube via a linked server. When I ran a query against the SSAS cube from directly from the SQL server it runs fine.
If however I run the query in SSMS from my PC I get
OLE DB provider "MSOLAP" for linked server "SSASServer01" returned message "The following system error occurred: .".
Msg 7373, Level 16, State 2, Line 1
Cannot set the initialization properties for OLE DB provider "MSOLAP" for linked server "SSASServer01".
In the properties on the linked server I've defined an account to use for the connection to get round the double hop issue
Any Ideas why I'm still getting the error?
Alex

Hi Mr P,
According to your description, you get the error 7373 with message "Cannot set the initialization properties for OLE DB provider "MSOLAP" for linked server "SSASServer01"." when connecting a SSAS cube via linked server.
Right?
In this scenario, based on the error code 7373, it points to the issue of MSOLAP provider, please firstly check the properties setting for MSOLAP. Make sure the "Allow Inprocess" is selected. You may also have other options selected depends on
your query.
Also check if ports for your server (1434 and 2383) are listening proper locally and externally. Please refer to a similar thread below:
https://social.msdn.microsoft.com/Forums/sqlserver/en-US/9d5bd9e0-c380-4a0f-bdab-857751c71fba/ole-db-msolap-provider-issues?forum=sqlanalysisservices
If you have any question, please feel free to ask.
Best Regards,
Simon Hou
TechNet Community Support

How to share internet if the server connects to it via VPN?

Hi, mac brothers! Need your help.
I have a server with 2 ethernet cards (en0, en1). It connects to internet via VPN on en0. LAN clients connect to the server using en1. I can't share VPN internet connection to LAN %(. (tried to find the answer in the 10.4 server documentation, but there is nothing about it).
I know how to share internet connection when there is no VPN - direct connection via DSL modem...
Can you help me?
PS; 0S X Server 10.4.11

You need to use NAT and have the firewall running.
And then you need to use the VPN connection (PPTP?) "interface" (when connected), probably ppp0 - not en0, in your NAT config. This can be achieved by dragging the config (small symbol in lower right corner in NAT config in Server Admin) to the desktop, edit it (look for en0 and change it to ppp0), save it, and then drag it back into the NAT config window and save.
I think the VPN tunnel must be up before turning on NAT/firewall so if you reboot the server you might need to turn NAT/firewall off -> on to make it work again.
If the WAN/ppp0 IP is not static (so you can enter it in your server DNS) you probably will have trouble with many of OS X services running in the server.
Most OS X server installations using an Internet connection with a shifting public IP is better off by putting a NAT router which can do the in initial connection (by DHCP, PPTP, PPPoE, whatever), between it and the Internet.

Automount Sharepoints via Connect to Server...

I have a number of sharepoints assigned to different users and groups....freelancers only have access to certain folders but managers have access to everything.
They are working on local accounts at the client machines which are not connected in any way to the server. They connect to the sharepoints via 'connect to server' in the 'go' menu. Is there any way of automounting chosen sharepoints without viewing a huge list of all of the sharepoints available?
I don't want users to have to log into their account on the local machines...
Thanks...

There are a couple of hints at macosxhints that cover this.
http://www.macosxhints.com/article.php?story=20020315095604777 or
http://www.macosxhints.com/article.php?story=20020911061931546
HTH
Regards.

We have an ipod touch, 3rd generation, 8GB. we lost the unlock code. we now try recovery via itunes, but can't connect to the ipod software update server. any suggestions?

We have an ipod touch, 3rd generation, 8GB. we lost the unlock code. we now try recovery via itunes, but can't connect to the ipod software update server. any suggestions?

Update Server
Try:
- Powering off and then back on your router.
- iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
- Change the DNS to either Google's or Open DNS servers
Public DNS — Google Developers
OpenDNS IP Addresses
- Try on another computer/network
- Wait if it is an Apple problem

Connection between SMD Agent and SMD server via SAProuter

In our scenario, we have to setup the connection between SMD agent and SMD server(solution manager server) via saprouter. But during the installation of SMD agent, we can only specify the hostname of the managing system, we have no place to add saprouter string(/H/..../H/). I I am not sure if we could connect the agent and server via saprouter, if so how to do it?
Hope someone can give us your precious advices on this issue.
Karl

Perfect; and thanks for your response. I found this help page for developers to implement P4 support over SAP router: http://help.sap.com/saphelp_nw73/helpdata/en/48/2992d7ad8758d7e10000000a421937/content.htm
But in the SM Diagnostics Setup options I can set up only a direct HTTP adresses and have no options to set up connections over a sap router to P4 ports directly. I can at the moment only solve my problems with NAT or firewall rules.
And also the diagnostic agent setup has no options to config a proxy or sap router. I found yesterday a blog on sdn side with screenshots of the setup with all available connection opetions to SLD... sry I can not post this link today.
This is an official statment of SAP from the current version of SMD guide; it is also possible but why not from the beginning???:
In some network conficurations, the Diagnostics agent has to connect to the Managing system though a SAP router.
This feature will be fully supported in Solution Manager 7 Ehp2 (7.02).
In order to enable this feature in Ehp1, please contact the Diagnostics Agent support team to get information on how to
setup the agent and on which patch level you can perform the installation.
This thread were a long time not answared; proxy and routing connections are mostly stepmotherly handled by SAP; this is also a problem by set up of automatic RFC generations in SMSY; why there are in the setup assitents no options to set up the router string.
I have absolutly no comprehension for this in year 2011. All this technics are good known and long time tested.
In this case the f**k has provoked an answare to this thread and this is what I expected; but sorry for my style You are right I could also writh why the heck
FAQ:
SMD root side on SDN: http://service.sap.com/diagnostics
SM FAQ: http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/4e49dbea-0c01-0010-91bd-f0b61388c9ae
SM Setup Home: http://wiki.sdn.sap.com/wiki/display/SMSETUP/Home
SM Diagnostic Troubleshooting Guide: https://websmp201.sap-ag.de/~sapdownload/002007974700000409092009E/DiagAgent_TroubleShooting.pdf
SMD Candidate Setup: http://wiki.sdn.sap.com/wiki/display/SMSETUP/Diagnostics+Agents

I keep getting error message " server stopped responding" when trying to connect to internet via wifi

My iphone works fine using cellar network, but will not connect to internet via wifi. Ive reset network setting with no diffrence.
Any ideas?

And you can turn the WiFi button on and off?
If yes, then you next need to try to Restore your iPhone from your backup.

Connecting 2 Clients via Server

Hi,
I asked a question about this a while ago, and got some helpful answers, but I just can't seem to get my head 'round the idea. I have 2 clients, and I want them each to connect to the server, and for the server to pair them up, and pass them off to a handler to do all the work.
The connection part of my client code:
public void start()
        try{
                InetAddress address = InetAddress.getByName("localhost");
                connect = new Socket(address, PORT);
            input = new BufferedReader(new InputStreamReader(connect.getInputStream()));
            output = new PrintWriter(connect.getOutputStream(), true);
            thread = new Thread(this);
            thread.start();
        catch(IOException exception)
            System.out.println("Error connecting to server " + exception);
    }The server code:
public Server()
        try
            //create server socket to listen for connections
            ServerSocket server = new ServerSocket(8000);
            while(true)
                //create socket when connection made
                Socket connection = server.accept();
                //assuming the 2 client connection goes here
                Handler thread = new Handler(connection);
                thread.start();
        catch(IOException exception)
                System.out.println("Error connecting: " + exception);
    }I have a feeling I'm just being really stupid about this, but I'd be really grateful if anyone could give me a clue, as it's really doing my head in!
C

hi there,
I believe rather than letting the server to connect two clients in two different threads, its beter if the server keeps two seperate connections with each clients and pass the required information about each clients -- viz. IP and Port nos.
Once each client gets their respective IP and Port no. , the clients themselves can connect to each other bypassing the server and helpin the load off the server machine.
Its like peer-2-peer computin.
i hope this idea can help
samabhik

HTTP connection from OSB web service to external system via a Proxy Server

Dear experts,
May I know has anyone tried to use HTTP protocol to send a request from OSB web service to external system via a proxy server? Heard that we need to establish some sort of tunnel (socket) to talk to Proxy Server. Can you please any have sample code or configuration steps to share?
Thank you very much!!

http://download.oracle.com/docs/cd/E13159_01/osb/docs10gr3/consolehelp/global_resources.html#wp1137294
Adding Proxy Servers
Use the Summary of Proxy Servers page to add and configure Proxy Server resources and make them available in Oracle Service Bus as a system resource. You must be in an active session to configure or reconfigure Proxy Server resources.
1. If you have not already done so, click Create to create a new session or click Edit to enter an existing session. See Using the Change Center.
2. Select System Administration > Proxy Servers.
3. Click Add.
4. In the Name field, enter a name for the Proxy Server resource. This is a required field.
5. In the Description field, enter a short description for the Proxy Server resource.
6. In the Host-Port Parameters section, enter the following information:
1. In the Server Host field, enter the host name or IP address of the Proxy Server. This is a required field.
The Server Host name for the Oracle Service Bus proxy server must be identical to the server host name of the actual proxy server.
2. In the Clear Text Port field, enter the Proxy Server clear-text port number.
3. In the SSL Port field, enter the Proxy Server SSL port number. You must enter either a clear text or SSL port number.
4. Click Add.
You can configure multiple Proxy Servers for each Proxy Server resource. This enables Oracle Service Bus to perform load balancing and offer fault tolerance features for the Proxy Server resource.
7. If the Proxy Server performs proxy authentication, enter a user name in the User Name field, and the associated password in the Password and Confirm Password fields.
These fields are optional, and required only if the Proxy Server is secured.
8. Click Save to create and save the Proxy Server resource in the current session.
9. To end the session and deploy the configuration to the run time, click Activate under Change Center.

Connecting to iTouch via "Connect to server"

Similar Messages

Maybe you are looking for