Connecting to OS/390's together using CIP and OSA (Enterprise Extender)

Is it possible to connect to OS/390's together (VTAM to VTAM) over WAN link using CIP against OSA & Enterprise Extender ?
If so has anyone demo what/how to configure each site.
Thanks

Hi Magnus. I presume your question is related to using CIP for host channel access for host-to-host connections vs. using OSA (OSA-E). You can certainly support IP connectivity (CLAW/CMPC+) using the CIP. So if the VTAM hosts are EE enabled (with EBN if VTAMs are in different subnets) you can support transport over the CIP. If EE is not in the picture then DLSw+ might fit into the picture since DLSw+ supports PU4/5 to PU4/5 connections. DLSw+ is not an SNI replacement solution however (EE/EBN is). Regards, Steve

Similar Messages

"Cannot connect to the iTunes Store" when using WiFi and Cisco VPN

hi
I'm on iPhone software 2.0 and have a connection to the internet via WiFi and VPN (using the integrated Cisco client). Everything works fine (Safari, Mail, mobileme push of contacts and calendars) but the iTunes Store and the App Store won't. While the App Store keeps spinning the iTunes Store says "Cannot connect to the iTunes Store". Has anyone else experienced a similar phenomenon?
thanks
Message was edited by: samaki

We're having the same issue. App Store and iTunes do not work when all traffic is tunneled over VPN. Yet, other applications like Safari, New York Times reader, Telnet, etc... work perfectly fine over VPN. If we have the iPhone switch over to using split tunneling VPN mode, then the App Store and iTunes work since they do not appear to be sending traffic over the VPN tunnel. I can say for certain that no outgoing traffic is being blocked on the VPN servers since I administer those servers. I also did a packet capture on the iPhone wireless session and it appears that the App Store sends traffic over the regular HTTP port. So it really doesn't make any sense from a VPN perspective why Safari would work but not the App Store or iTunes when you're tunneling all traffic over VPN. Our iPhones are using the latest firmware (5F136). If anyone has any update, please do share.

Can't connect to a majority of webpages using the RG54gs residential gateway

I'm stumped with the MSI Residential Gateway.
We primarily got it as a gift for my father-in-law who had just aquired a centrino laptop. He started complaining that he was not being able to download his e-mails. Found out later, it was because the gateway shuts off the connection after some time of inactivity and on occassion after a few minutes. There was some improvement after I installed the new firmware (feb release) but it was still there.
I decided to bring it home and test it on my network. I immediately noticed that I couldn't visit all the sites I used to. It seemed that all the secondary sites were no longer available. An example is, opened google (can connect), google searched for RG54gs and come up with the msi website but when I click on the link to the msi website, I get a page not available error. This is also the same thing that happens to the rest of the links. I hooked all connections back to my accton router and I'm able to access all site again.
Can't figure out what the problem is?
There was a suggestion that for Ppoe connection you're suppose to leave the "connect on demand" button disabled. I found a little improvement when it was enabled. All this is using the wired part. Using the wireless is totally useless with almost everything unaccessible even though the signal is excellent.
Sorry for the long story but it's really got me to a point where I don't know what else to do.

Are you sure that this did not happen on the morning of June 15th when the major web sites were actually unavailable due to Akami problems?
Check the RG54GS configuration and see what DNS server it is using. Check the configuration of the PC and make sure it is using the RG54GS as the DNS server.
You don't mention if you are ADSL or cable. An incorrect MTU length (guess at 1400 if your service does not tell you) can cause connections to be dropped.
I use ADSL and could not connect at all until I got the new firmware, since then things have been OK. I am on a very marginal ADSL connection.

Using INET and DATADIRECT JDBC Drivers to connect MS SQL Server 2005

Hi,
I have reqmt to connect SQL server 2005 from ODI using INET and DATADIRECT JDBC drivers to test Local characters Encoding.
In my case, Oracle is the Source and SQL Server 2005 is the Target. I have problem while interfacing Local Characters to SQL Server 2005 using com.microsoft.sqlserver.jdbc.SQLServerDriver driver( which is default driver provided by ODI). To fix local charatcters issue, I want to try using INET or DATADIRECT JDBC drivers. Please provide me the below of any one has used these Drivers to connect SQL Server 2005 from ODI.
We are trying to connect to MS SQL Server 2005 from ODI Topology Mgr using INET and DATADIRECT JDBC Drivers. We need the following info to connect to the same,
--> What are list of the drivers need to be placed in OraHome_1\oracledi\drivers path?
--> Where can i get the latest driver versions.
--> What are the JDBC DRIVER and URL formats.
--> Any other additional configurations?
--> Does these drivers support interfacing of Local character data.
Please respond...
Regards,
Anil

Check this article [HOW TO: SQL & JAVA|http://www.shahriarnk.com/Shahriar-N-K-Research-Embedding-SQL-in-C-Sharp-Java.html] for details on how to connect to SQL Server database from C#.NET database applications as well as Java database applications. It also describes how to pass embedded SQL queries (SELECT, INSERT, UPDATE, DELETE), calling stored procedures, pass parameters etc.

Can I use a Time Capsule to extend my wireless network.

Hi, I have just bought a 3TB time capsule as my old (flat style) 500GB TC is reaching full capacity. The old style TC will then be surplus to requirements as a data storage unit, at least for myself, though it might be useful for my son to use as his Time Capsule.
Ideally, as we have a wireless 'blind spot' out in the rear extension of the house, it would be useful to use the unit to extend my wireless network (and also use it as a separate TC if possible). Is this possible? If it is how would I go about it?
Hope someone can help . . . .
Cheers
John

Is it possible for you to consider connecting the Time Capsules together using a wired Ethernet connection?
Here is what Apple has to say in their support document about extending:
Adding Wi-Fi base stations when it is unnecessary can reduce Wi-Fi throughput because the Wi-Fi network will require more data management overhead. The network configuration also becomes more complex. In the case of a wirelessly extended network, throughput may be reduced to less than 60 percent of that of a single device. The general rule is to keep the Wi-Fi network as simple as possible. You can accomplish this by using the minimum number of Wi-Fi base stations required to service the physical network area and by using Ethernet wherever possible.
Extending the range of your Wi-Fi network by connecting Wi-Fi base stations together using Ethernet is always the best option, and will provide the best throughput.
Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations

Can you connect via thunderbolt a mac book air 13" (2013) and a imac 21" (2013) together, using the iMac 21" as a 2nd screen

Can you connect via thunderbolt a mac book air 13" (2013) and a imac 21" (2013) together, using the iMac 21" as a 2nd screen

Welcome to Apple Support Communities
Of course. As both have Thunderbolt, it's as simple as buying a Thunderbolt cable, connect them and press Command and F2 keys on the iMac, so the iMac will be used as an external display for the MacBook Air. If you want more information, see > http://support.apple.com/kb/PH11302

Connecting two computers together using an intermediate server.

I'm trying to write a program that allows users to connect to a server and then pairs off users to chat. I setup the connections between the two clients and that works fine, but as soon as the server disconnects from the two clients the connection between the two is lost. The server is always runnning, it sets up sockets that are global to the clients, what am I missing?

I am not very sure how are you trying to do the job. Is it
client1 <-----> server <----> client2
i.e. all message from client1 is send to server which passes them on to client2 and vice versa. If yes, you will loose connectivity when server goes down. Instead, try a an connection client1 directlyt to client2. for this you might need to run a socket server on client2
the pseudo code might look like this
1. client1 connect to server.
2. client1 check client2 is logged in and convays interest to connect to client2
3. client1 gets IP address and port of client2 from server. This info has been convayed to sever when client 2 logged in.
4. client1 opens socket connection to client2
5. client2 has ServerSocket with establishes recieves connection, opens socket and starts chat seesion.
Note that after step 5, client1 and client2 are directly connected and server no longer comes into picture. It only acts as repository for IP address and port of client2.
hope it helps
Amitabh

I have 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II. How do I connect? 4000 only has 1 Display Port and 1 DVI. 5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute?

I just bought a 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II. How do I connect? 4000 only has 1 Display Port and 1 DVI. 5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute any work at all? I read where on a PC they would work together, but on a MAC they do not.
I read that Display Port has higher band width than DVI, NEC monitors for best performance they recommend using DIsplay Port.
When I was setting this up I looked at a Nvidia Quadro 4000, unfortunately it was for PC, it had 2 Display Ports, in the Mac version they reduce it to one. I did not think there could be a difference.
Mainly want to use it for CS6 and LR4.
How to proceed???
I do not want to use the Quadro 4000 for both, that would not optimize both monitors, one DP and 1 DVI. Using just the 5770 would work but I do not think the 4000 would be doing anything, and the 5770 has been replaced by the 5870.more bandwidth.
Any ideas, I am a Mac newbie, have not ever tried a Mac Pro, just bought off ebay and now I have these problems.
As a last resort I could sell both and get a 5870. That would work, I'm sure of that, it's just that I wanted the better graphics card.
Thanks,
Bill

The Hatter,
I am a novice at Mac so I read all I can. From what I understand the NEC monitors I bought require Display Port for their maximum performance. The GTX 680 only has DVI outputs. Difference from what I understand is larger bandwidth with the DP.
You said I have the 4000 for CUDA. I am not all that familiar with CUDA and when I do read about it I do not understand it.
A concern I have is, that if I connect the 2 high end NEC monitors via the 5770, using it's 2 Display Ports I would have nothing connected to the 4000. Is the 4000 doing anything with nothing connected? I read where in a PC system the 2 cards would interact but in a Mac system they do not.
Bottom line, as I see it, the 4000 will not be useful at all to me, since I want a dual monitor set-up.
So far the 5870 seems the best choice, higher band width than the 5770, and it has 2 Display Ports to optimize the NEC monitors.
I'm not sure how fine I am splitting hairs, nor do I know how important those hairs are. I am just trying to set up a really fast reliable system that will mainly be used for CS6 and LR4. Those NEC monitors are supposed to be top notch.

Error while using REMAP_TABLE and WHERE clause together in IMPDP

I am trying to move some records from a very large table to another small table.
I am facing trouble while using REMAP_TABLE and WHERE clause together in IMPDP.
Problem is data filter is not getting applied and all records are getting imported.
here is how I have simulated this. please advice.
CREATE TABLE TSHARRHB.TMP1
A NUMBER,
B NUMBER
begin
Insert into TSHARRHB.TMP1
   (A, B)
Values
   (1, 1);
Insert into TSHARRHB.TMP1
   (A, B)
Values
   (2, 2);
COMMIT;
end;
expdp system/password TABLES=tsharrhb.TMP1 DIRECTORY=GRDP_EXP_DIR DUMPFILE=TMP1.dmp REUSE_DUMPFILES=YES LOGFILE=EXP.log PARALLEL=8
impdp system/password DIRECTORY=GRDP_EXP_DIR DUMPFILE=TMP1.dmp LOGFILE=imp.log PARALLEL=8 QUERY='TSHARRHB.TMP1:"WHERE TMP1.A = 2"' REMAP_TABLE=TSHARRHB.TMP1:TMP3 CONTENT=DATA_ONLY
Import: Release 11.2.0.1.0 - Production on Fri Dec 13 05:13:30 2013
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
Connected to: Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production
With the Partitioning, Automatic Storage Management, OLAP, Data Mining
and Real Application Testing options
Master table "SYSTEM"."SYS_IMPORT_FULL_01" successfully loaded/unloaded
Starting "SYSTEM"."SYS_IMPORT_FULL_01": system/********@GRD6.RBSG DIRECTORY=GRDP_EXP_DIR DUMPFILE=TMP1.dmp LOGFILE=SSD_93_TABLES_FULL_EXP.log PARALLEL=8 QUERY=TSHARRHB.TMP1:"WHERE TMP1.A = 2" REMAP_TABLE=TSHARRHB.TMP1:TMP3 CONTENT=DATA_ONLY
Processing object type TABLE_EXPORT/TABLE/TABLE_DATA
. . imported "TSHARRHB"."TMP3"                           5.421 KB       2 rows
Job "SYSTEM"."SYS_IMPORT_FULL_01" successfully completed at 05:13:33
here I am expecting only 1 record to get imported but both the records are getting imported. please advice.

The strange thing compared to your output is that I get an error when I have table prefix in the query block:
Connected to: Oracle Database 11g Enterprise Edition Release 11.2.0.4.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
Master table "SYSTEM"."SYS_IMPORT_FULL_01" successfully loaded/unloaded
Starting "SYSTEM"."SYS_IMPORT_FULL_01": system/******** DUMPFILE=TMP1.dmp LOGFILE=imp.log PARALLEL=8 QUERY=SYSADM.TMP1:"WHERE TMP1.A = 2" REMAP_TABLE=SYSADM.TMP1:TMP3 CONTENT=DATA_ONLY
Processing object type TABLE_EXPORT/TABLE/TABLE_DATA
ORA-31693: Table data object "SYSADM"."TMP3" failed to load/unload and is being skipped due to error:
ORA-38500: Unsupported operation: Oracle XML DB not present
Job "SYSTEM"."SYS_IMPORT_FULL_01" completed with 1 error(s) at Fri Dec 13 10:39:11 2013 elapsed 0 00:00:03
And if I remove it, it works:
Connected to: Oracle Database 11g Enterprise Edition Release 11.2.0.4.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
Master table "SYSTEM"."SYS_IMPORT_FULL_01" successfully loaded/unloaded
Starting "SYSTEM"."SYS_IMPORT_FULL_01": system/******** DUMPFILE=TMP1.dmp LOGFILE=imp.log PARALLEL=8 QUERY=SYSADM.TMP1:"WHERE A = 2" REMAP_TABLE=SYSADM.TMP1:TMP3 CONTENT=DATA_ONLY
Processing object type TABLE_EXPORT/TABLE/TABLE_DATA
. . imported "SYSADM"."TMP3"                             5.406 KB       1 out of 2 rows
Job "SYSTEM"."SYS_IMPORT_FULL_01" successfully completed at Fri Dec 13 10:36:50 2013 elapsed 0 00:00:01
Nicolas.
PS: as you can see, I'm on 11.2.0.4, I do not have 11.2.0.1 that you seem to use.

Using Thunderbolt and DisplayPort devices together

Hello!
Is it possible to use HDD storage connected via thunderbolt (WD My Book Thunderbolt Duo) and monitor with display port together with one thunderbolt port on Mac? Or thunderbolt chain will work only for all thunderbolt devices?
Thanks!

The Thunderbolt pass-through/daisy chaining on most TB drives will only work with a TB display (or anther TB device) not with a display port adopter.

Using Airport And Ethernet Together

Having read Christopher Breen's solution to using Airport and Ethernet together,
http://www.macworld.com/weblogs/mac911/2006/10/airportswitch/index.php
I am still wondering if this can apply to my situation. I have an Airport Exteme BS distributing the wireless signal on it's own node. Nothing is physically connected to the BS except an ethernet cable running to a hub which is connected to the cable modem. While my ISP service isn't supplying service faster than Airport will manage, no problem...but, I would like to have the advantage ethernet networking between my machines for all the advantages that ethernet speed can bring to that situation.
My connection to the internet is from WAN from the cable modem. I have an ethernet connection from the BS that I can run a cable back to say, an iBook. Will this work? I want wireless internet, but ethernet for machine to machine networking.
JAL
iBook G3/500 G4/Dual 450 Mac OS X (10.4)
iBook G3/500 G4/Dual 450 Mac OS X (10.4)

Helpful response, but I am uncertain this is what I am after. First, the hub is at the other end of the house, inconvenient to run a cable to it in this way. Presently, "Distribute IP Addresses" is turned off. This is way it had to be set since the AEBS is on a separate node. I just wonder why I can't run a cable from the AEBS LAN port back to the iBook. Looking for best possible speed when networking from my studio G4 while keeping the wireless internet setting.
Any reason making the config the way I am imagining will not work?

Connect to a local server whilst using VPN

I have SABnzbd+ running on my MBP.
Since my Linksys WAG320N router supports NAT Loopback, I can connect to it's web UI using my local IP, 192.168.0.2 OR my ISP-assigned static IP, 72.xxx.xxx.xxx.
However when I'm connected to the VPN, using OpenVPN & Viscosity, I can't connect to the SABnzbd+ server on either address.
I tried setting up DynDNS with their auto-updater, and using a host name instead of IP address, still no luck.
I use SABnzbd+ as an example, it's the same problem with ANY locally runnining server (uTorrent UI, etc).
Thanks

I use the built in VPN for company access. However, by default it "sends all packets to VPN route", which I do not like. I put together a script to set only the networks I need to go through that route using the "route add" comment. I set my default route whatever my ISP default route is at the time of my connection. This allows me both worlds (vpn connections and internet). Not sure if that helps you or not.

Has anyone had success using SharePoint and FrameMaker 10 together using CMS?

Has anyone had success using SharePoint and FrameMaker 10 together using CMS?

Thanks for reminding to at least update the results thus far.
Update 4:
I did get quite a bit of support initially although slowly over a period of a month or so. After Adobe FM support and my SharePoint systems engineer reviewed how FM10 was setup on my computer (which I am the admin for our department’s SP site) and how it interfaces with our SharePoint 2010 Enterprise Edition, there was two conclusions:
Basically Adobe FM Support said that FM10 did not support claims-based authentication and they can no longer help me. They said it will work with FM11 when it comes out.
My SP Systems Engineer, said that FM10 is connecting to SP 2010 just fine but that the FM10 has a software glitch that causes FM10 lose control when executing checkout procedure within FM10. I can checkout and edit that same file in SP with no problems.
About a month later, I upgraded to FM11 and ran into the same problem. I attempted to get Adobe FM Support to help and they said they will look into and get back to me. That was in July and I have not heard anything more from them, and to be honest, my schedule has been extremely busy the last 5 months that I have not had time to pursue it any further.
Needless to say, I was very disappointed with the SP interface and, overall, the lackluster support I received from Adobe. Having a working SP interface was one of the criteria for purchasing TCS3.5 (and subsequent upgrade) in the first place.
One thing of note, we migrated from SP 2007 to SP 2010 in February 2011 and, at the time of Adobe support, I still had access to my SP 2007 site. FM10 and FM11 had to no issues working with SP2007. Unfortunately, SP 2007 is not an option for me anymore.
Also, another observation of FM10/11 not working with SP 2010, it seems that FM10/11 is automatically configured to work with SharePoint Drafts folder locally when connecting to the SharePoint library. This worked just fine with SP 2007 but SP 2010 does not use SharePoint Drafts folder locally the same way (the programming changed, don’t recall where I saw it, probably when searching this issue online) and I suspect that is one of the main issues why it does not work correctly.
So at this time, I have not found a working solution to this problem.

How to connect my loptop to my tv using hdmi

how do i connect my loptop to my tv using hdmi i have it hooked up but how do i get tv to identify my computer

Try this: Connecting Notebook to TV with HDMINote that the Computer should be Shut Down when the HDMI cable is connected.Turn off both the computer and the TV.Connect the HDMI cable to the computer and TV.Switch on the TV. Adjust the TV settings to receive HDMI audio.Boot the computer to allow it to detect the connection to the TV.Start > Control Panel > icon view >Sound >Playback tab > Select HDMI as Default Device > OK If it doesn’t “take” the first time, REPEAT one or more times. I hope this helps.Say “Thanks!” by clicking Kudos Star in the Post that helped you.Mark a Post “Accepted Solution” to say your issue is solved.

How do i use my iMac and the macs wired internet connection to share the internet with my iPod and iPhone

How do i use my iMac and the macs wired internet connection to share the internet with my iPod and iPhone. For 6months I had set up a network that shared the internet through bluetooth to my iPod 5th gen but i messed it up when i tried to add my iPhone 5s and i can't remember how to do it.

The following has instructions: OS X Mavericks: Share your Internet connection

Connecting to OS/390's together using CIP and OSA (Enterprise Extender)

Similar Messages

Maybe you are looking for