Connecting to USB h/d cause everything dropped

Bought the new extreme about a month ago. Connected it to USB h/d (BUFFALO HD-HB160U2 WR), everything was OK until a week ago, where I usually update firmware when prompted(2.7.1 now). The h/d is visible and accessable for while, then the mapped drive got lost, plus, all networking dropped, I can't even ping the router. The only way to fix is to reset the router. This is all about wired connection, no wireless involved. Now I have to turn off the h/d in order to ensure internet connection. Anyone shed the light on this? I never had such problem when connect the h/d to a computer to share. Thx a lot.

changed to Maxtor drive and issues resolved. The disk is also much quieter than the buffalo, but seems a little slower for initial response.

Similar Messages

Connecting an USB drive is causing the status light to turn yellow on 2013 Airport Extreme

I recently purchased a new Airport Extreme ac to improve wifi performance in my house. It has been working fine. Today I decided that I would try to connect one of my USB backup drives to the Airport Extreme. As soon as it is connected, the status light goes yellow. It appears to be trying to read the drive, which has only a timemachine backup folder on it. But the status light never comes back to green.
Here is the System Information for the USB:
INIC-1610P      :
Capacity:          500.11 GB (500,107,862,016 bytes)
Removable Media:          Yes
Detachable Drive:          Yes
BSD Name:          disk1
Product ID:          0x1e40
Vendor ID:          0x13fd (Initio Corporation)
Version:           1.07
Serial Number:          0010101E40000000
Speed:          Up to 480 Mb/sec
Manufacturer:          Initio
Location ID:          0xfd130000 / 5
Current Available (mA):          500
Current Required (mA):          2
Partition Map Type:          GPT (GUID Partition Table)
S.M.A.R.T. status:          Not Supported
Volumes:
disk1s1:
Capacity:          209.7 MB (209,715,200 bytes)
BSD Name:          disk1s1
Content:          EFI
MyBook:
Capacity:          499.76 GB (499,763,888,128 bytes)
Available:          162.73 GB (162,727,297,024 bytes)
Writable:          Yes
File System:          Journaled HFS+
BSD Name:          disk1s2
Mount Point:          /Volumes/MyBook
Content:          Apple_HFS

Well, I unplugged the drive from my laptop and plugged it in to the airport extreme again and this time it stayed green and I now see the drive in the airport utility under partitions. Very odd. Going to try restarting the airport to see if it will go green.

N95 kept on dropping connection during USB data tr...

Greetings,
I was trying to install Garmin Mobile XT to my phone N95. However, during USB data transfer, the phone would kept on beeping...and at about 3/4 remaining during data transfer, the connection would suddenly drop. And me had to reattempt installation all over again! Please advice what could be causing these problems? This is very annoying and frustrating...
Solved!
Go to Solution.

Does this happen when doing anything else while phone is connected via USB? In PC Suite mode?
If it happens all the time, I would recommened uninstalling Nokia PC Suite, Nokia connectivity cable drivers and PC Connectivity solutions and then redownload Nokia PC Suite from www.nokia.com/pcsuite

HT1338 Hello, I dropped coffee on my keyboard. I wiped the coffee off as fast as I could, BUT I hit al sorts of buttons while it was still connected to my computer. NOW Everything looks photo negative. I want to restore my desktop defaults.

Hello, I dropped coffee on my keyboard. I wiped the coffee off as fast as I could, BUT I hit al sorts of buttons while it was still connected to my computer. NOW Everything looks photo negative. I want to restore my desktop defaults.

Hit control-option-command-8 to reverse the negative effect. You can also do this, and check other settings, in System Preferences>Universal Access.

Lenovo U410 - Wifi disconnected when connected to USB.

Hi, I bought a Lenovo U410 sometime in July 2012 (bought it back home in Malaysia). About a week or two after I bought it, the laptop sleeve cover came off, causing the laptop to fall to the floor. But fortunately, other than a small dent (pictured) at one corner of the laptop, everything seems to work okay. [well, if you plug in an earphone, only the right side would play but I'm not too concerned about that] I've enjoyed using the laptop, everything works fine & easy for me. I use it mainly for my studies (I'm a rising junior in Madison) and occassionally some photos & video processing. Other than The Sims, I never actually used my laptop for 'gaming' stuff (was planning to soon though). But recently, in the past few months, I realized that there's something wrong with the laptop. It connects to WiFi just fine and everything, but whenever I connect my external hard drive to my laptop, my Wifi would disconnect automatically & wouldn't reconnect until I remove the hard drive. This happen even when I connect a USB port to the laptop, but doesn't happen when I connect a small USB pendrive or my phone (Samsung Note 4) or a bluetooth speaker. Not sure what's the problem with it, and I'm a noob when it comes to things like this, so I would really appreciate your help. Thanks in advance!

Hi syazanazura,
Welcome to Lenovo Community Forums!
The Laptop maybe having power issue since the drop.
You can try opening
Control Panel / Hardware and sound / Power Options / Change plan settings on selected power plan / Change Advanced power Settings
Now look for the Wireless Adapter Settings Make sure not to use the scroll but use the scrollbar to the right
Open the Wireless adapter setting and make sure that both plugged in and on Battery are set to Maximum Performance.
Let me know if this works for you
Regards
Solid Cruver

Trouble connecting to USB Harddisk

Hi all,
I recently bought an AEBS to set up a wireless network for my Windows PC and Laptop. So far so good, both wintel machines can connect to internet, and both can print to the USB printer hooked to the AEBS.
I also connected a USB harddisk to the AEBS, but only my laptop can connect to it. My workstation fails and keeps telling me that the supplied password is incorrect, no matter what I try: client access or disk access.
*One more thing I like to know:*
How can I create a share on my Desktop that will be visible for my laptop. I used to have this when I had everything wired with a simple router. But now I have it all wireless, and I cannot figure out how to do this (sharing directories and/or disks) because Windows does not show the wireless network in "available network places" (or whatever this is called).
Thanks

Questions not valid anymore. Dropped the Windows PC and am now completely Mac orientated

10 3.9 - external drive crashes PB when connected by USB or FireWire

Subject says most of it... "10 3.9 - external drive crashes PB when connected by USB or FireWire"
Details: I have one external drive which, when connected to my PowerBook via either FireWire or USB, causes the computer to lock up with the message: "You need to restart your computer. Hold down the Power button for several seconds or press the Restart button." The same thing happens whether the drive is there on bootup or if it is connected later.
The drive worked fine until yesterday, when I stupidly installed Windows Media Player even though the internal drive was almost full. It took a while, but I discovered that disconnecting this particular external drive made everything work again, though slowly.
Then I freed up 15GB on the internal drive, and everything works normally _unless that drive is attached. Another drive connected the same way works fine.
I have searched around on this message but have yet to find the way out. I did figure out what the first question will probably be, so here's the answer:
The "kernel panic message" each time seems to be the date and time and then "localhost /usr/libexec/panicdump: Error (-1) setting variable - 'aapl,panic-info'"
Where should I start?
Thanks.
15" Powerbook Mac OS X (10.3.9) External drives connected via USB or FireWire

Still hoping for some sort of advice here... Have tried many approaches but can only confirm that simply connecting that particular drive (or enclosure?) always gets an immediate shutdown.
Thanks for anything,
Steve

Since upgrading to mavericks anything i connect via usb disconnects

since upgrading to mavericks anything i connect via usb disconnects randomly. everything from ipods, phones and usb thumb drives is there a patch or fix out there. starting to become a pain. PLEASE HELP

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

When iPhone 5s is connected via USB no audio is heard

Hi There -
I've seen older threads on this issue but I don't think I've really come across any solutions. My issue started yesterday; now before reading further I have to ask that you please keep in mind that I did perform the latest upgrade on my iPhone a bit earlier in the day.
When I connect my iPhone to my vehicle sync system and announce that I'd like to connect via USB, the voice recognition repeats my request and then the music on my iPhone shows to be playing on the display in my vehicle. The problem is that though the music appears to be playing and the minutes played are being displayed there is no audio coming through. When I switch to the Bluetooth Audio option all sound comes through.
Now, as a 2nd test, we connected my sons iPhone 5s via USB (he has not taken the latest update on his iPhone) and the same issue happens with his. Voice recognition changes to the USB format as requested, music appears to be playing but no audio is heard. When we change his phone to Bluetooth Audio the audio comes through nice and clear.
I'm not entirely convinced the update caused the issue so I wanted to put this out there to see if anyone has run into this and were able to actually resolve the issue.
I know the USB cable is working fine because when I do plug it into either phone the phone makes the little connection sound and pops up a brief battery percentage box. I also know the cable is working because when we announce USB as our audio of choice the system recognize USB via the iPhone.
One other thing I tried looking for was the option on the phone to switch from Docked to Synch - I know on my iPhone 4 I was able to switch back and forth through iTunes and would also have the option if I tried to watch anything via You Tube when connected to the dock; I cannot find this anywhere on the 5s when connected via USB.
Help is greatly appreciated!!!

I have had similar troubles with wifi.. some improvement removing BlackBerry desktop software & drivers & reinstalling after reboot... I used the same installer I had previously, but a fresh downloaded installer couldn't hurt...
10.3.1 SW .1779 OS .2726 WLAN .1.1 Radio .2727

Hi I'm trying to install an HP C4180 printer as net printer through Alicegate router (Thompson technicolor). Printer works ok when connected with USB to Macbook air, but cannot be seen on the printer installation configuration. Mac OSx 10.7 (Lion)

Hi folks.
From this morning I'm trying to "see" an HP printer C4180 connected on the USB port of the wi-fi router (TIM Alicegate ADSL2 Wifi+N, manufacturer Technicolor).
I installed latest drivers and checked everything is ok and works fine until printer is connected directly with USB to my Macbook Air.
Then I connect the USB to the router and try to find the printer.
On Alice help suggest to find it by ging to system preferences, then printers, add printer with "+", select "windows" sheet. There I can see - not always in reality, but sometimes - the "workgroup" in the left column, select, "alicegate" in second column, select, and here instead of finding the printer list there is a pop up saying that "the server version you are trying to connect to is not supported".
Reading other forums, it may seem that the problem is Lion not yet supporting this kind of connection.
Here a photo of the situation when the message occurs:
Help..
Thanks and regards
Luca

anchio ho lo stesso problema con Mas Os x 10.7.4
con il sistema 10.5 funziona perfettamente
credo sia un problema del sistema
ho provato con 10.8 stesso problema
ciao

Ipod Nano (1st Gen) no longer connects at usb 2.0 speeds

I have had my nano since it was released almost 2 years ago. When I got it, it connected to my computer (running Win XP) at usb 2.0 speeds, however about 5 months ago, it stopped connecting at this speed and only connected at 1.1 speeds causing very slow updates. I assumed it was my old computer and lived with it. However I just bought a new computer, running windows vista, that has all usb 2.0 ports. I finally tried to connect my ipod this week (I waited until the new ITunes was released), and on the new computer it still connects at USB 1.1. I get the message in windows that says it could operate faster if connected to a usb 2.0 port. I have tried all usb ports on the computer, tried restoring the ipod to factory settings, rebooted, etc, but it still only connects at the slow speed. All other devices I have connect at USB 2.0, except the Ipod. Has anyone else experienced a similar issue? Does anyone know a solution?
Dell 9200 Other OS Windows Vista

Yes you have a one year warranty from the date of purchase from Apple. Go to this link and on the bottom right hand side it will ask you to enter your serial number and will tell you if you are still under warranty. http://www.apple.com/support/
If you are you can take it to a Apple store, or request service online here http://depot.info.apple.com/ipod/
If it is out of warranty you can google a third party service provider and get it serviced out of warranty. There are two that I know of that provide free diagnostic service. You only pay for shipping and they will tell you what is wrong and what it will cost to fix. They are ifixipodsfast.com and ipodmods.com but there are others also (I just have no experience with them) Good luck and as was stated it should charge from your usb. and just for grins, look at the docking connector on your ipod and see if there is any obstruction that is obvious.

HP LaserJet P1102w Not Working with Mac when connected via USB

I'm using an old HP LaserJet P1102w - I installed the drivers and the software, and when I connect to my computer, nothing happens. It recognizes the printer, and it says that it's using "Generic PCL Printer" as the driver. The Print Queue has a good time pretending it printed things, and nothing comes out.
Someone tell me how to fix this POS before I throw it out a window.

Hi oprachck,
I see by your post you are having some issues printing from the Mac. I can help you, but I will need some more information.
The driver "Generic PCL Printer", wouldn't be the correct driver using the Laserjet P1102w.
If you are using 10.8 or 10.9, the drivers are installed by the Apple Updates.
OS X v10.9 Mavericks: Installing and Using the Printer on a Mac.
If you are using 10.7 or lower the drivers can be downloaded from this link.
HP LaserJet Pro P1102w Printer Drivers.
Check the driver name that is installed for the printer. Make sure it shows just the printer's name.
Click the Apple menu and then click System Preferences. Click Printers & Scanners, highlight the printer name on the left side and on the right side of the screen should show the name.
If the full printer name isn't listed correctly, delete it and add the printer name back in from the list. Click the - sign to delete the driver and then click the + sign to add the driver, might have to click the drop down to select the printer's name to add it in.
What operating system are you using? Mac OS X: How Do I Find Which Mac OS X Version Is on My Computer?
How is the printer connected? (USB/Wireless)
Please provide in detail the results if you are still having issues.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

HT202731 Unstable operation when 2 or more USB devices connected to usb port on a MacBook Pro running Yosemite

I have tried connecting a number of devices to my MacBook Pro but I have found if I try to connect 2 or more using either usb ports or a usb hub the computer reports 'disk not ejected properly' and sometimes it will fail to recognise the device and remove it from the desktop or it stalls operation and I have to turn the computer off at the power button.
I have tried erasing the hard drive and reinstalling the operating system.
I have done various types of reset suggested by apple support.
The computer has been to an Apple dealer who has tested the hardware but found nothing due to the intermittent nature of the problem.
I have operated the computer with only the software originally installed on it present.
Could it be possible that a virus could be present on the usb devices I am trying to connect?
My computer is a MacBook Pro (13-inch, Mid 2012)
Processor 2.5 GHz Intel Core i5
Memory 4 GB 1600 MHz DDR3
Startup Disk Macintosh HD
Graphics Intel HD Graphics 4000 1024 MB
Operating System X Yosemite 10.10.1
Devices I have connected to USB ports all USB 3.0 compatible in a variety of combinations:-
7 port superspeed USB 3.0 hub (powered).
4 port Inateck USB 3.0 portable hub (not powered).
Buffalo ultra portable 500Gb USB 3.0 hard drive.
Seagate Expansion portable 500Gb USB 3.0 hard drive.
Seagate Expansion desktop 2Tb USB 3.0 hard drive (powered).
Seagate Expansion desktop 3Tb USB 3.0 hard drive (powered).
ScanDisk Cruiser Edge 16Gb USB stick.
ScanDisk Cruiser Edge 32Gb USB stick.
Hewlett Packard 16Gb USB stick. (This causes an instant crash now.)

Why?
- Because when I'm editing/ rendering lots of HD video everyday, I don't want to share system resources between virtual machines... I want the entire system's resources devoted to what I'm doing.
- I don't want to spend anymore money than I have to in order to buy one of the faster virtual systems. Not to mention, I've had a bad experience with Parralels in the past and I'd rather not use one again.
- I really don't want to clutter up my system anymore than I have to for a project that's only going to take a few weeks.
- I don't mind swapping hard drives... it takes two minutes, and I have an empty ssd just sitting on the shelf.
So, back to my original question. Can I just swap the computer's drives, then install Ubuntu on the second drive and be good to go without any harm to my MacBook Pro or OSX on the other drive (which wouldn't be connected when Ubuntu is running)?
Thanks.

I have a Canon LBP5360 laser printer connected via USB cable to my MacPro running 10.6.8 I have downloaded the latest UFR2 divers. I am trying to connect to the printer but the printer is not showing appearing in Print

I have a Canon LBP5360 laser printer connected via USB cable to my MacPro running 10.6.8
I have downloaded the latest UFR II driver. (UK Version)
I am trying to connect to the printer but the printer is not appearing in my Print/Fax Preferences.
When I click the box "More Printers" under the Default printer the drop down box gives me a heading "Canon IPv6 (UFRII) with the option to add or cancel. (The add is highlighted). But there are no printers showing in the box. Nothing. Can anyone help?
Is there a problem with my Mac setup or maybe a setting in my printer?

Mac UFR II Printmonitor
UFR II Printmonitor is application software that interfaces with the software for the printer, and is installed with the printer driver. You can start UFR II Printmonitor in the following folder to check the printer status, and errors. Refer to the Help how to use the Print Monitor.
MF3010, MF8000 Series, MF8000C Series, MF8300 Series, MF8300C Series:
Print Monitor: [Library] - [Printers] - [Canon] - [CUPSCMFP] - [Utilities]
Other Printers:
Print Monitor: [Library] - [Printers] - [Canon] - [UFR2] - [Utilities]

I want to record a keybord connected by usb in an IMac and only sound like an ambient microphone. What is wrong?

I want to record a keyboard connected by usb port and only sound like an ambient microphone. What configuration is wrong? Thank you

The optimum choice is to format it ExFAT, but do so on the PC, not the Mac. Alternatively, you can make two partitions - one for the Mac; one for the PC. Partition the drive using GUID when you make the two partitions. Format one using Mac OS Extended, Journaled. Format the other on your PC using NTFS if you won't need to write to it from the OS X side or use ExFAT if you do.
Drive Partition and Format
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to two. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) you will use for Windows from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to MSDOS.
6. Click on the Erase button.
When you connect the drive to your PC reformat the PC volume to either NTFS or ExFAT.

Connecting to USB h/d cause everything dropped

Similar Messages

Maybe you are looking for