Connecting Two Wired Networks with WRT54G

I have a server (IP 40.1.238.27) that I need to connect to clients (IP 40.52.2.59,.60).  I have a Linksys WRT54G wireless router.  The chap I was chatting with at support says it is possible but could not tell me how to do it.  He mentioned Advanced Routing but I couldn't figure out how to do it.
Does anyone know?
Thanks,

Let me know the other network settings ... such as Wireless settings & connection type ...

Similar Messages

  • Connecting two wired routers ,is it worth the hassle?

    Connecting two wired routers ,is it worth the hassle?
    I want to add a Linksys E1000, to a Chinese made trenda modem/router already connecting a network.
    Because I find it easier to set up port forwarding,dyn dns, on Linksys than the present Trenda modem/router  ,which is poorly  documented & not supported from china

    Posting the correct link.
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=785463d9ecaf4cac84aed245b08d615f_3733.xml&pid=80&r...
    The Search Function is your friend.... and Google too.
    How to Secure your Network
    How to Upgrade Routers Firmware
    Setting-Up a Router with DSL Internet Service
    Setting-Up a Router with Cable Internet Service
    How to Hard Reset or 30/30/30 your Router

  • Airport Express and wired network with static IPs

    I have a wired network with static IPs. I have a block of free IPs I can use to connect to this network. Manually setting any of one IP from this block on my MacBook Pro via ethernet works great - full network connectivity including internet.
    What I wish to do is add an Airport Express in between my MBP and the network, so that I may have greater freedom (wireless opposed to wired). Is the AX capable of this? If yes, what are the correct settings? Keep in mind there is no DHCP server on the network.
    I have tried giving the AX an IP manually and then accessing it from the MBP having the AX share IP (effectively becoming it's own DHCP server?). This gives internet connectivity, but I can't see any of the servers on the network. I assume because I'm now on a new subnet.
    So I then changed the AX settings to not distribute an IP and gave the MBP another IP from the block (different from the AX). This gives me the network, but no internet.
    What am I doing wrong?

    Okay, I made a mistake and forgot to set the DNS servers manually. It seems the second method works fine. I've set up WPA2 security as well - I'm assuming this is okay in this situation. What is the correct term for this setup? A wireless access point bridge? Is there anything more I should know about this setup? TIA

  • I have a RCA media streamer that will not connect to my network with a new airport extreme.

    I have a RCA media streamer (Model # DSB872WR)  that will not connect to my network with a new airport extreme.I had to create a new network and  my computers are connected but media streamer will not. Can anyone help? Thank you

    Hi, papineaubill!
    Welcome to The Canon Forums, and thank you for your inquiry!
    We appreciate your participation, though we need to let you know that the Canon Forum is hosted and moderated within the United States by Canon USA. We are only able to provide support for Canon products manufactured for and used within the US market.  If you live outside the United States, please click here and select your country or region for your support needs.
    Feel free to discuss Canon products sold outside of the United States, but please be aware that you will not receive support directly from Canon USA.
    Thanks for choosing Canon!

  • Connecting two Nexus switches with link

    Hi,
    I would like to connect two nexus switches with a link. Like one c5020 and one c5548p. How do i need to configure the ports at both the switches which will be joined with a fiber cable.
    For MDS switches such links becomes E-port and fabric is merged. Not sure what happenes at the Nexus swictches. Any input will be appreciated.
    Thanks,

    Do you have fc modules in each nexus? If so, they act much like the MDS 9148. All ports should be default auto speed and auto switchport mode. Insert fc-sfp's and a regular multimode fc cable between them. Default mode is fc switch.
    If that doesn't work, configure the mode on each port as E.
    Once done, the fc switch portion of each nexus will merge.
    Dave

  • Is possible to connect two i-phone4 with bluetooth?

    Is possible to connect two i-phone4 with bluetooth?

    For what reason.  Some apps were made to interact with another iPhone with the same app running over bluetooth.
    All info is in the manual if you mean for other reasons.
    http://manuals.apple.com

  • Connecting two Nexus 5020 with 10G ISL link

    Hi Experts,
    I am trying to connect two nexus 5020 with a 10G ISL link.
    Per my understanding, with new release 5.0.3 N2(2a) ISL link between two nexus switch is supported.
    Following is my config
    c5020-1(config)# show running-config int vfc 32
    !Command: show running-config interface vfc32
    !Time: Fri Dec  2 01:14:38 2011
    version 5.0(3)N2(2a)
    interface vfc32
      bind interface Ethernet1/32
      switchport mode E
      switchport trunk allowed vsan 3040
      no shutdown
    c5020-1(config)#
    c5020-1(config)# sho running-config int eth1/32
    !Command: show running-config interface Ethernet1/32
    !Time: Fri Dec  2 01:16:15 2011
    version 5.0(3)N2(2a)
    interface Ethernet1/32
      switchport mode trunk
      spanning-tree port type edge trunk
    c5020-1(config)#
    I have similar config on the other switch. But for some reason the link does not come up. vfc port keep "initializing" and Eth port stays isolated.
    c5020-1(config)# sh int vfc32
    vfc32 is trunking (Not all VSANs UP on the trunk)
        Bound interface is Ethernet1/32
        Hardware is Virtual Fibre Channel
        Port WWN is 20:1f:00:0d:ec:ca:04:bf
        Admin port mode is E, trunk mode is on
        snmp link state traps are enabled
        Port mode is TE
        Port vsan is 3040
        Trunk vsans (admin allowed and active) (3040)
        Trunk vsans (up)                       ()
        Trunk vsans (isolated)                 ()
        Trunk vsans (initializing)             (3040)
        1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
        1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
          0 frames input, 0 bytes
            0 discards, 0 errors
          0 frames output, 0 bytes
            0 discards, 0 errors
        last clearing of "show interface" counters never
        Interface last changed at Fri Dec  2 01:17:28 2011
    c5020-1(config)#
    c5020-1(config)# sh int eth1/32 fcoe
    Ethernet1/32 is FCoE Isolated
    c5020-1(config)#
    If any expert throw some light to make me understand things better will be helpful.

    i have not connected two Nexus before but looking at your eth 1/32 interfaces ..do you think it needs to be "
    switchport trunk allowed vlan" your "FCOE" VLAN ?

  • Can't connect to wireless network with Apple Computers (WRT54G)

    Hi.
    I have had a password protected router (WRT54G) for over two years that any pc will connect to if I give them the password.  However, my roommate has an apple laptop and he can't connect, no matter how many times we try.  I just got an ipod touch, and it can't connect to the network either.  We are inputting our password correctly - why can't apple computers connect to my wireless network??
    Again, my router is a WRT54G.
    Thanks !!!
    Message Edited by Debo24 on 05-24-2009 06:41 PM

    Make sure you enter the correct password...To check your Wireless Settings follow this link
    If your Wireless Security is WEP then use WEP Key1 and not the Passphrase, make sure to enter a dollar sign on your Apple Computer when you attempt to connect...If your Wireless Security is WPA/WPA2 then use the WPA Shared key and no dollar sign is required...

  • Weird problem with lat 120l wired network with Linksys WRT54g ver 5

    when I use the wired network adapter on my latitude 120l
    broadcom 440x 10/100 integrated controller driver ver 4.60.0 11/21/2006
    when connected directly to the router the router consantly reboots until i unplug the laptop
    wireless works fine I just do not use it when I am in the same room where my router is
     the router is a linksys WRT54g ver 5  fw ver 1.02.5
    Latitude 120l --- linksys WRT54g
    i have to connect it though either a switch or hub then the router
    works fine this way
    Latitude 120l --- Linksys EZXS88W  ---- Linksys WRT54g
    i disable the wireless when not using it 

    This is a hardware issue. have you tried different ports on the router.

  • Can't connect to wireless network with Dell Inspiron 1525 with Vista

    I set up a wireless network about a week ago, and have made it with the following security features: WEP, enable only certain MAC addresses to connect, and disabled broadcasting the SSID.  I have been able to use it just fine with my Mac computer using airport, but when I have tried to connect my roommates computer, a dell inspiron 1525 with vista, it can't connect.  I can locate the network but when I try to connect to the network, I get a message saying that for an Windows cannot connect to the network and that the Wireless association failed due to unknown reasons.  It then says to connect with your administrator, but that is me.  I have a minimal knowledge of computers just enough to be dangerous and am basically figuring this out as I go along.  If anyone has some advice for me, both my roommate and I will be very grateful.
    Thanks,
    - Jill
    Solved!
    Go to Solution.

    Sorry I am not sure if this is needed but I am using a WRT54G router ver.6.

  • Not Connecting to Wired Network and Forcing the loss of all Connections on the Home Network

    Just got a new G550 laptop  w/Win 7 OS. Tried to connect to wired router and got message "network cable not connected". Recycled laptop and router and came up with router connected to the laptop. Same message after search and identify steps finished. I then noticed I lost connection to the net/router with my other home networked units as well! Tried another cable, same results along with losing the entire home network connection. Disconnected the G550 from home network, via the cable, and the home network reconnected without any intervention. Tried another reboot directly connected to the cable modem, no go there either!
      I also rebooted with the wireless search shutoff and got the same problems as on the wired attempt. Thought it might have been the NIC card so I exchanged the system back at the store.  Sorry, same problem!! 

    I have a very similar problem... New Lenovo G550, running Vista Home Premium 64-bit. Right from the start it causes my TrendNet TEW-432BRP router to crash every 10 seconds. I bought a new DLink WBR-1310 and experience the same problem. Connecting to either router through either a wireless connection or a LAN cable connection causes the router to crash every 10 seconds. The router crashes, reboots, establishes a connection with the laptop, communication starts and then the router crashes again.
    I am looking for help.

  • Trouble connecting to wireless network with WRT610N

    Need some help please.  I have a WRT610N with 3 laptops that I am connecting to the network.  I have been able to successfully connect 2 of them, but the third is a no go.  I have the security set for WPA-TKIP, have a network code set; but when I enter the code on the one laptop and try to connect it won't do it.  The laptop will connect via wired connection and will also connect wireless if I take the security off.  Many times I have noticed the security settings on the laptop will change after I have save them; going from WPA-TKIP back to OPEN-WEP.  I have tried everything, but no luck.  The laptop is running Windows XP Home edition on a Sonay Vaio PCG K-15.  Any help would be greatly appreciated.  Thanks

    Well try upgrading the firmware of the router & keep on holding tightly
    the reset button in such a way that power light is blinking on the
    router & then do a complete network power cycle i.e., unplug the power
    cables from the modem & from the router & then plug in the power cable
    to the modem first once all the lights are solid green you could plug
    in the power cable to the router & check out it will definately work!!
    Open the setup page of router using 192.168.1.1 then put in the password as admin...
    all you need to do is do the wireless settings such as Radio Band Frequency to Standard 20 MHZ frequency,channel to 11.
    Also,the advanced wireless settings to Beacon Interval=50,Frag
    thres=2306 & Rts thres=2307 & then uncheck a Block Anonymous Internet
    Requests & it will definately work!!!

  • HP CP1525nw - Connect via wired network and wireless ad hoc?

    At my job we have our HP 1525nw printer connected into the network printserver via ethernet cable.  The printer has its own IP address setup on the network.   
    With support for XP computers ceasing, a copule of computers will be cut off/blocked from the job's network.  One computer is close enough where we can make a USB connection to print.  Another is located on another bench.  Furthermore, the one that is further away from the printer also can't be upgraded to a compliant Windows OS due to incompatibility with specialized software used to operate equipment hooked up to this computer. 
    Is it at all possible for this wired network printer to also be setup to print wireless via an ad hoc connection?  The idea was perhaps we could install a wireless card on thix XP computer and  print wirelessly via a direct connection to the printer, avoiding having to connect to it via the wired network at all.  But it is sounding like this wouldn't be possible.  Looking for a direct answer before I start shopping around for a wireless PCI card. 
    This question was solved.
    View Solution.

    From other posts I have read, I think the CP1525 can be either ethernet or wireless not both at the same time.  That will prevent you from setting up with an adhoc network the way you described.
    You might try an inexpensive wireless router with a build in print server attached to the usb port.  then add wireless USB wireless dongles to the XP computers.  Be sure you make sure that the wireless dongles support XP. Also for security purposes you will want to leave the wireless router disconnected from your network.
    If your fairly tecky and you don't mind playing a bit you could check your local thrift store for a used router with a print server.  For printing you don't need the fastest wireless available.  Just make sure it is a b/g router (not a B only one).
    Treefrog
    Please mark the post that solves your problem as "Accepted Solution"
    Sometimes it takes several posts back and forth to get to a solution - please be patient.
    I am employed by HP

  • Using Airport Express as a remote WDS station to connect two wired LANs

    I have an Airport Extreme base station connected to a cable modem that gives internet access to both wired and wireless clients. I would like to wirelessly connect this base station to an airport express in a nearby building that also has a wired network so that both wired networks look like one big network. I figured that I would have to use WDS (using the Extreme as the main and the Express as the remote). I've followed all of the directions, but I'm not sure what the setting for Connection Sharing should be on the Express. Technically I am sharing the connection, but isn't the Extreme going to be doing all of the DHCP/NAT/etc.? So my question is, for this configuration what setting should I be using for Connection Sharing on the Extreme: Share a public IP address or Off (Bridge Mode)?

    So my question is, for this configuration what setting should I be using for Connection Sharing on the Extreme: Share a public IP address or Off (Bridge Mode)?
    "Off (Bridge Mode)" With this setting the AirPort Express Base Station (AX) will pass-thru the NAT & DHCP services of the AirPort Extreme Base Station (AEBS). That way all clients connected to either network will be on the same subnet.

  • 4400 Controllers - Best Practise for connecting to wired network

    At one time the best practise recommendation for wireless was to treat the traffic as untrusted and separate it from the wired network by firewalls and intrusion detection. A lot of the reason for this was the weakness of WEP. Now with strong authentication and encryption (e.g., WPA2 and EAP-TLS) in use, and the use of wireless controllers, I'm wondering what the industry is recommending (and doing in case the actions aren't the same as the recommendations).
    Are organizations connecting the wireless controllers directly to the internal network or are they separating them with a firewall and IDS infrastructure? If the latter, what does the architecture look like? Are there documents on the Cisco site or on the Internet that show how the controllers could be firewalled? Everthing I've seen shows connections directly to the internal network. Is firewalling the controller an overreaction to the historical paranoia from the WEP days?

    The argument would be that regardless of what security you put on the wireless, you still don't have the physical security - i.e. someone doesn't need to walk into your building to use your network.
    Beyond that if you're using strong auth/enc you can currently be considered safe, we have customers using that direct into their LANs (but then, we also have customers with WEP direct into their LANs!)...
    If you are concerned or really need belt 'n' braces security, then go down the firewall/IDS route - there's no harm in it if you have the money. It really depends how much functionality and ease of use you need to balance against it.
    Aaron
    Please rate helpful posts

Maybe you are looking for