Connecting vlans to router

If I create a sub if on my router, do I have to create 1 for each vlan or can I assign to vlans to 1 sub interface ?

Hi
AFAIK if u r going on for intervlan routing then you can assign one vlan id followed by the encapsulation dot1q command.
but if you are terminating Q-in-Q Frame you can have secondary vlan id followed by the primary one..
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fswtch_r/xrfscmd1.htm#wp1056958
http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124tcr/tmpls_r/mpl_a1ht.htm#wp1016968
regds

Similar Messages

  • AP1121G connection with Internet Router

    Hi! My requirement is to connect the access point to an Internet Router through a common L2 switch so that wifi-enabled laptops will receive public ips through the DHCP pool defined on the AP and be able to access raw internet. The Internet Router has 2 subnets one for the leased-line and the other on the LAN interface.
    I have configured the BVI interface with one of those public IPs and specified the default-gateway as the LAN IP on the Internet Router; on which I have created a reverse route for reachability to the public subnet on AP.
    I am able to reach to the default-gateway but have no reachability for the subnets beyond.
    While working on the problem, I have connected a laptop directly to the LAN interface and confirmed connectivity and browsing to the internet. Next, I bypassed the Nortel switch and connected the AP directly to the LAN interface, I can ping to the public dns servers but browsing is not happening.
    However, I can browse from wifi laptops when I connect the AP on the client LAN segment.
    Am I missing something here? Please have a look and advise.

    You really should be nat'ing on the router...
    Let me get this straight... you have an router with 2 ethernet ports. One is for the lease line and the other is connected to a layer 2 switch? The AP is connected to the layer 2 switch and is on the same vlan as the port on the router?
    When you bypass the Nortel switch and connect to the router everything works, but when you connec to the Nortel switch it doesn't.
    Check to see if you have native vlan checked on the AP... you might have to set the native vlan or no tagging on the Nortel switch in which the ap is connected to.

  • MacBook Pro Cannot Connect to Wireless Router

    I have a brand new MBP and it won't connect to any non-apple wireless routers
    - my computer is 2 days old (it's awesome and I love it accept that I can't get wireless connection at home)
    - wireless router: westell versalink model 327 W
    - PROBLEM: my mbp will detect the network just fine, but won't connect to it...just times out, it will connect to a neighbors linksys, but cannot load any internet pages, so still not helpful. When I try to connect to the wirelesss router using the network utility it asks for a WEP password, which it never did before because it's an open wireless router. (I know you should always password protect, but it's not my router...I'm just in the same house)
    - I had a powerbook G4 and ibooks that have all connected fine to the same wireless network. My dad has an HP laptop that also connects fine
    - it only connects to the apple brand airport wireless routers
    - it will connect to the wireless router if I plug in the ethernet cord
    - I have tried checking the connections, allowing all connections, repairing my disk permissions (even though my computer is only 2 days out of the box), resetting the router, opening the router so no password is needed...NOTHING WORKS!
    - I also tried another wireless router (netgear): doesn't work
    I've been reading around in some forums and this seems to be an apple and maybe more specifically a macbook pro issue (just by process of elimination). One forum said that it was because of an airport update that basically "breaks" mbp's airport and makes it not accept any non airport wireless connections, apple supposedly is working on a fix but who knows
    I'm feeling disappointed and very upset that this is even a problem, especially with how many people I read are dealing with the same issue wit still no solution. My mbp was far from cheap and this just shouldn't be an issue. I'm planning on contacting apple and getting to bottom of this or at least some kind of answer.

    - it will connect to the wireless router if I plug in the ethernet cord
    this is because there is an actual physical connection between the router and the machine, so the router allows the connection automatically. i believe ALL wireless routers have a "Wireless Access List" in their config. the owner of the wireless router must add any machine or device seeking to gain access to the wireless router. consult your routers documentation on how to access the router from a web page and add your machine. this is usually done by adding the machine's mac address to the wireless access list. i added my 15"mbp and iphone to my netgear wireless router in about ten minutes and have no problem connecting every time.
    also, when making any changes in Network Preferences, be sure to "Apply" after any change or adding any wep key. let me know if you have any questions.

  • I have just update my MacBook to Snow Leopard 10.6.3.  Unfortunately I can not now connect to the internet.  I have a time capsule that is connected to a router.  This is working with other devices but if I try to connect with the MB everything stops?

    I have updated my MB to Snow Leopard 10.6.3 - I know this means I am a little behind the times but the problems I am now having seem to justify my reluctance.  Now am unable to connect to the internet!  I use a time capsule connected via a router.  Everything is still OK with every other device (PC, I phone, Ipod) in the house so I know the "Network" is still enabled and there is no problem with the ISP.  Strangley whenever I boot up the MB it appears to freeze the network such that the other devices also will then not access the internet.  To regain access I have to turn off the MB and reset the router.  Any help gratefully recieved as I have tried some of the ideas i have found in the internet but nothing is working.  Thanks.

    That's odd.
    Try this: Unplug your Time Capsule and your router. On your MBP, click the Wi-Fi icon and select "Open Network Preferences".
    Click the lock icon to authenticate, then click the "gear" and select "set service order". Wherever AirPort (or Wi-Fi - I forget what Snow Leopard calls it) appears, drag it elsewhere in the list. Click OK, then Apply, then power up your router and TC.
    If that doesn't result in any change, repeat the above but try making the service(s) you do not need "inactive".
    The purpose of this is to reset or at least change your Network Preferences, which somehow got confused upon upgrading to SL.

  • Can't connect to new router...

    Hi
    I've just installed a new intranet here at my place and one of the changes is that my computer must connect to another router now. While everything works perfect in both Knoppix and windows, I can't get Arch to connect....
    I've collected all files to show you my situation (I think):
    rc.conf:
    # /etc/rc.conf - Main Configuration for Arch Linux
    # LOCALIZATION
    # LOCALE: available languages can be listed with the 'locale -a' command
    # HARDWARECLOCK: set to "UTC" or "localtime"
    # TIMEZONE: timezones are found in /usr/share/zoneinfo
    # KEYMAP: keymaps are found in /usr/share/kbd/keymaps
    # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
    # CONSOLEMAP: found in /usr/share/kbd/consoletrans
    # USECOLOR: use ANSI color sequences in startup messages
    LOCALE="en_GB.utf8"
    HARDWARECLOCK="localtime"
    TIMEZONE="Europe/Brussels"
    KEYMAP="be-latin1.map.gz"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    # HARDWARE
    # Scan hardware and load required modules at bootup
    MOD_AUTOLOAD="yes"
    # Module Blacklist - modules in this list will never be loaded by udev
    MOD_BLACKLIST=(pcmcia)
    # Modules to load at boot-up (in this order)
    # - prefix a module with a ! to blacklist it
    MODULES=(ath_pci fglrx powernow-k8)
    # Scan for LVM volume groups at startup, required if you use LVM
    USELVM="no"
    # NETWORKING
    HOSTNAME="icarus"
    # Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
    # interfaces.
    # Interfaces to start at boot-up (in this order)
    # Declare each interface then list in INTERFACES
    # - prefix an entry in INTERFACES with a ! to disable it
    # - no hyphens in your interface names - Bash doesn't like it
    # Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
    lo="lo 127.0.0.1"
    eth0="dhcp"
    INTERFACES=(lo eth0)
    # Routes to start at boot-up (in this order)
    # Declare each route then list in ROUTES
    # - prefix an entry in ROUTES with a ! to disable it
    gateway="default gw 192.168.123.254"
    #gateway="default gw 192.168.1.1"
    ROUTES=(gateway)
    # Enable these network profiles at boot-up. These are only useful
    # if you happen to need multiple network configurations (ie, laptop users)
    # - set to 'menu' to present a menu during boot-up (dialog package required)
    # - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network-profiles
    #NET_PROFILES=(main)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    # - prefix a daemon with a ! to disable it
    # - prefix a daemon with a @ to start it up in the background
    DAEMONS=(@syslog-ng iptables @network !netfs @hal @crond !ifplugd @alsa @ddclient @denyhosts @sshd @mpd @powernowd)
    # End of file
    lspci -vvv section for my network card:
    02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
    Subsystem: Unknown device 1631:d008
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
    Latency: 64 (8000ns min, 16000ns max)
    Interrupt: pin A routed to IRQ 19
    Region 0: I/O ports at 8800 [size=256]
    Region 1: Memory at ff3ef400 (32-bit, non-prefetchable) [size=256]
    Expansion ROM at 50000000 [disabled] [size=64K]
    Capabilities: <access denied>
    ifconfig output:
    eth0 Link encap:Ethernet HWaddr 00:13:D3:8B:9E:89
    inet addr:192.168.123.1 Bcast:192.168.123.255 Mask:255.255.255.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:2 errors:0 dropped:0 overruns:0 frame:0
    TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:690 (690.0 b) TX bytes:994 (994.0 b)
    Interrupt:19 Base address:0x400
    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:68 errors:0 dropped:0 overruns:0 frame:0
    TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:3998 (3.9 Kb) TX bytes:3998 (3.9 Kb)
    lsmod:
    Module Size Used by
    nls_cp437 5888 1
    vfat 10880 1
    fat 45852 1 vfat
    cpufreq_userspace 3536 1
    ipt_REJECT 3968 1
    ipt_LOG 6144 8
    nf_conntrack_ipv4 14092 6
    xt_state 2432 6
    nf_conntrack 52872 2 nf_conntrack_ipv4,xt_state
    nfnetlink 4760 2 nf_conntrack_ipv4,nf_conntrack
    xt_limit 2560 10
    xt_tcpudp 3328 22
    iptable_filter 2688 1
    iptable_mangle 2560 0
    ip_tables 10452 2 iptable_filter,iptable_mangle
    x_tables 11908 6 ipt_REJECT,ipt_LOG,xt_state,xt_limit,xt_tcpudp,ip_tables
    isofs 31040 0
    zlib_inflate 16256 1 isofs
    tda827x 6916 1
    saa7134_dvb 15884 0
    dvb_pll 12292 1 saa7134_dvb
    ohci1394 31408 0
    ieee1394 81720 1 ohci1394
    video_buf_dvb 4996 1 saa7134_dvb
    dvb_core 71976 1 video_buf_dvb
    tda1004x 15492 2 saa7134_dvb
    snd_seq_oss 29312 0
    snd_seq_midi_event 6528 1 snd_seq_oss
    snd_seq 46672 4 snd_seq_oss,snd_seq_midi_event
    snd_seq_device 6924 2 snd_seq_oss,snd_seq
    ppdev 7556 0
    lp 9348 0
    tuner 61352 0
    usb_storage 79296 1
    snd_pcm_oss 37024 0
    snd_mixer_oss 14592 1 snd_pcm_oss
    firewire_ohci 15360 0
    firewire_core 36032 1 firewire_ohci
    crc_itu_t 2304 1 firewire_core
    pcspkr 2944 0
    saa7134 119244 1 saa7134_dvb
    ppp_generic 23828 0
    slhc 5760 1 ppp_generic
    ide_core 112580 1 usb_storage
    8139cp 19584 0
    8139too 23168 0
    mii 4864 2 8139cp,8139too
    video_buf 20356 3 saa7134_dvb,video_buf_dvb,saa7134
    compat_ioctl32 1536 1 saa7134
    ir_kbd_i2c 7184 1 saa7134
    ir_common 30084 2 saa7134,ir_kbd_i2c
    videodev 26752 1 saa7134
    v4l2_common 15744 3 tuner,saa7134,videodev
    v4l1_compat 14084 2 saa7134,videodev
    parport_pc 35556 1
    parport 31304 3 ppdev,lp,parport_pc
    serio_raw 5764 0
    psmouse 35984 0
    snd_atiixp 15884 2
    snd_ac97_codec 95652 1 snd_atiixp
    ac97_bus 2432 1 snd_ac97_codec
    snd_pcm 69124 4 snd_pcm_oss,snd_atiixp,snd_ac97_codec
    snd_timer 19332 3 snd_seq,snd_pcm
    snd 45028 11 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
    soundcore 6496 1 snd
    snd_page_alloc 7816 2 snd_atiixp,snd_pcm
    rtc_cmos 7328 0
    rtc_core 14984 1 rtc_cmos
    rtc_lib 2944 1 rtc_core
    sg 26652 0
    k8temp 4864 0
    i2c_piix4 7948 0
    i2c_core 20352 8 tda827x,saa7134_dvb,dvb_pll,tda1004x,tuner,saa7134,ir_kbd_i2c,i2c_piix4
    ehci_hcd 30732 0
    tsdev 6720 0
    ati_agp 7308 0
    ohci_hcd 19588 0
    evdev 8192 4
    thermal 10888 0
    fan 3844 0
    button 6160 0
    battery 8324 0
    ac 4100 0
    powernow_k8 13972 0
    freq_table 3984 1 powernow_k8
    processor 24788 2 thermal,powernow_k8
    fglrx 726624 11
    agpgart 27224 2 ati_agp,fglrx
    wlan_scan_sta 12416 0
    ath_rate_sample 13312 1
    ath_pci 104744 0
    wlan 195504 4 wlan_scan_sta,ath_rate_sample,ath_pci
    ath_hal 231264 3 ath_rate_sample,ath_pci
    usbcore 112520 4 usb_storage,ehci_hcd,ohci_hcd
    ext3 119432 3
    jbd 54312 1 ext3
    mbcache 6916 1 ext3
    sr_mod 14756 0
    cdrom 34336 1 sr_mod
    sd_mod 22784 8
    pata_atiixp 5888 2
    sata_sil 8456 4
    ata_generic 5380 0
    libata 108084 3 pata_atiixp,sata_sil,ata_generic
    and dmesg output after a fresh bootup:
    Linux version 2.6.22-ARCH (root@workstation64) (gcc version 4.2.1) #1 SMP PREEMPT Fri Aug 31 19:54:09 UTC 2007
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable)
    BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data)
    BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS)
    BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
    127MB HIGHMEM available.
    896MB LOWMEM available.
    found SMP MP-table at 000ff780
    Entering add_active_range(0, 0, 262096) 0 entries of 256 used
    Zone PFN ranges:
    DMA 0 -> 4096
    Normal 4096 -> 229376
    HighMem 229376 -> 262096
    early_node_map[1] active PFN ranges
    0: 0 -> 262096
    On node 0 totalpages: 262096
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 4064 pages, LIFO batch:0
    Normal zone: 1760 pages used for memmap
    Normal zone: 223520 pages, LIFO batch:31
    HighMem zone: 255 pages used for memmap
    HighMem zone: 32465 pages, LIFO batch:7
    DMI 2.3 present.
    ACPI: RSDP 000F90C0, 0014 (r0 ACPIAM)
    ACPI: RSDT 3FFD0000, 0038 (r1 A M I OEMRSDT 7000520 MSFT 97)
    ACPI: FACP 3FFD0200, 0084 (r2 A M I OEMFACP 7000520 MSFT 97)
    ACPI: DSDT 3FFD0430, 397A (r1 0AAAA 0AAAA000 0 INTL 2002026)
    ACPI: FACS 3FFDE000, 0040
    ACPI: APIC 3FFD0390, 005C (r1 A M I OEMAPIC 7000520 MSFT 97)
    ACPI: MCFG 3FFD03F0, 003C (r1 A M I OEMMCFG 7000520 MSFT 97)
    ACPI: SSDT 3FFD3DB0, 0D6E (r1 ATI ATIPATCH 1 INTL 2002026)
    ACPI: OEMB 3FFDE040, 0056 (r1 A M I AMI_OEM 7000520 MSFT 97)
    ATI board detected. Disabling timer routing over 8254.
    ACPI: PM-Timer IO Port: 0x808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    Processor #0 15:7 APIC version 16
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000)
    Built 1 zonelists. Total pages: 260049
    Kernel command line: root=/dev/sda1 rootfstype=ext3 ro vga=795 clock=pit
    Warning! clock= boot option is deprecated. Use clocksource=xyz
    mapped APIC to ffffd000 (fee00000)
    mapped IOAPIC to ffffc000 (fec00000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 16384 bytes)
    Detected 2189.023 MHz processor.
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 1034320k/1048384k available (2393k kernel code, 13332k reserved, 783k data, 304k init, 130880k highmem)
    virtual kernel memory layout:
    fixmap : 0xfff82000 - 0xfffff000 ( 500 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
    lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
    .init : 0xc0421000 - 0xc046d000 ( 304 kB)
    .data : 0xc035641f - 0xc041a1bc ( 783 kB)
    .text : 0xc0100000 - 0xc035641f (2393 kB)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 4382.14 BogoMIPS (lpj=7301039)
    Security Framework v1.0.0 initialized
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 1024K (64 bytes/line)
    CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Compat vDSO mapped to ffffe000.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    Freeing SMP alternatives: 11k freed
    Early unpacking initramfs... done
    ACPI: Core revision 20070126
    ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
    CPU0: AMD Athlon(tm) 64 Processor 3700+ stepping 01
    Total of 1 processors activated (4382.14 BogoMIPS).
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
    ..MP-BIOS bug: 8254 timer not connected to IO-APIC
    ...trying to set up timer (IRQ0) through the 8259A ... failed.
    ...trying to set up timer as Virtual Wire IRQ... works.
    Brought up 1 CPUs
    Booting paravirtualized kernel on bare hardware
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
    PCI: Not using MMCONFIG.
    PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
    PCI: Using configuration type 1
    Setting up standard PCI resources
    ACPI: Interpreter enabled
    ACPI: (supports S0 S1 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    PCI: Transparent bridge - 0000:00:14.4
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 15 devices
    ACPI: ACPI bus type pnp unregistered
    SCSI subsystem initialized
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    ACPI: RTC can wake from S4
    pnp: 00:08: iomem range 0xfff80000-0xffffffff could not be reserved
    pnp: 00:0b: ioport range 0xe00-0xe7f has been reserved
    pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
    pnp: 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
    pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
    pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
    pnp: 00:0e: iomem range 0xc0000-0xcffff could not be reserved
    pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
    pnp: 00:0e: iomem range 0x100000-0x3fffffff could not be reserved
    Time: pit clocksource has been installed.
    PCI: Bridge: 0000:00:02.0
    IO window: 7000-7fff
    MEM window: ff200000-ff2fffff
    PREFETCH window: bff00000-dfefffff
    PCI: Bridge: 0000:00:14.4
    IO window: 8000-8fff
    MEM window: ff300000-ff3fffff
    PREFETCH window: 50000000-500fffff
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
    TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    checking if image is initramfs... it is
    Freeing initrd memory: 481k freed
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: overridden by ACPI.
    highmem bounce pool size: 64 pages
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    Installing knfsd (copyright (C) 1996 [email protected]).
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    Boot video device is 0000:01:00.0
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:02.0:pcie00]
    vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 7680k, total 262144k
    vesafb: mode is 1280x1024x24, linelength=3840, pages=67
    vesafb: protected mode interface info at c000:5977
    vesafb: pmi: set display start = c00c5a0b, set palette = c00c5a57
    vesafb: pmi: ports = 7810 7816 7854 7838 783c 785c 7800 7804 78b0 78b2 78b4
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
    Console: switching to colour frame buffer device 160x64
    fb0: VESA VGA frame buffer device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
    loop: module loaded
    input: Macintosh mouse button emulation as /class/input/input0
    PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    input: AT Translated Set 2 keyboard as /class/input/input1
    TCP cubic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    Freeing unused kernel memory: 304k freed
    libata version 2.21 loaded.
    sata_sil 0000:00:11.0: version 2.2
    ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 16
    scsi0 : sata_sil
    scsi1 : sata_sil
    ata1: SATA max UDMA/100 cmd 0xf881ec80 ctl 0xf881ec8a bmdma 0xf881ec00 irq 16
    ata2: SATA max UDMA/100 cmd 0xf881ecc0 ctl 0xf881ecca bmdma 0xf881ec08 irq 16
    ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
    ata1.00: 312581808 sectors, multi 16: LBA48
    ata1.00: configured for UDMA/100
    ata2: SATA link down (SStatus 0 SControl 300)
    scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5
    ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 17
    scsi2 : sata_sil
    scsi3 : sata_sil
    ata3: SATA max UDMA/100 cmd 0xf8826880 ctl 0xf882688a bmdma 0xf8826800 irq 17
    ata4: SATA max UDMA/100 cmd 0xf88268c0 ctl 0xf88268ca bmdma 0xf8826808 irq 17
    ata3: SATA link down (SStatus 0 SControl 300)
    ata4: SATA link down (SStatus 0 SControl 300)
    ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:14.1 to 64
    scsi4 : pata_atiixp
    scsi5 : pata_atiixp
    ata5: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ff00 irq 14
    ata6: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ff08 irq 15
    sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 < sda5 > sda3 sda4
    sd 0:0:0:0: [sda] Attached SCSI disk
    ata5.00: ATA-6: ST3160021A, 8.01, max UDMA/100
    ata5.00: 312581808 sectors, multi 16: LBA48
    ata5.00: configured for UDMA/100
    ata6.00: ATAPI: _NEC DVD_RW ND-3530A, 2.01, max UDMA/33
    ata6.00: configured for UDMA/33
    scsi 4:0:0:0: Direct-Access ATA ST3160021A 8.01 PQ: 0 ANSI: 5
    sd 4:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
    sd 4:0:0:0: [sdb] Write Protect is off
    sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 4:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
    sd 4:0:0:0: [sdb] Write Protect is off
    sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sdb: sdb1 sdb2 sdb3 sdb4
    sd 4:0:0:0: [sdb] Attached SCSI disk
    scsi 5:0:0:0: CD-ROM _NEC DVD_RW ND-3530A 2.01 PQ: 0 ANSI: 5
    sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 5:0:0:0: Attached scsi CD-ROM sr0
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    ath_hal: module license 'Proprietary' taints kernel.
    ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
    wlan: 0.8.4.2 (0.9.4)
    ath_pci: 0.9.4.5 (0.9.4)
    ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 20 (level, low) -> IRQ 19
    ath_pci: switching rfkill capability off
    ath_rate_sample: 1.2 (0.9.4)
    ath_pci: switching per-packet transmit power control off
    wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
    wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
    wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
    wifi0: H/W encryption support: WEP AES AES_CCM TKIP
    wifi0: mac 7.9 phy 4.5 radio 5.6
    wifi0: Use hw queue 1 for WME_AC_BE traffic
    wifi0: Use hw queue 0 for WME_AC_BK traffic
    wifi0: Use hw queue 2 for WME_AC_VI traffic
    wifi0: Use hw queue 3 for WME_AC_VO traffic
    wifi0: Use hw queue 8 for CAB traffic
    wifi0: Use hw queue 9 for beacons
    wifi0: Atheros 5212: mem=0xff3f0000, irq=19
    Linux agpgart interface v0.102 (c) Dave Jones
    [fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
    [fglrx] USWC is disabled in module parameters
    [fglrx] PAT is disabled!
    [fglrx] module loaded - fglrx 8.40.4 [Jul 31 2007] on minor 0
    ACPI: duty_cycle spans bit 4
    ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
    powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3700+ processors (version 2.00.00)
    powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x6
    powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x8
    powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa
    powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
    input: Power Button (FF) as /class/input/input2
    ACPI: Power Button (FF) [PWRF]
    input: Power Button (CM) as /class/input/input3
    ACPI: Power Button (CM) [PWRB]
    ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
    ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 20
    ohci_hcd 0000:00:13.0: OHCI Host Controller
    ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
    ohci_hcd 0000:00:13.0: irq 20, io mem 0xff6fe000
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 4 ports detected
    ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 20
    ohci_hcd 0000:00:13.1: OHCI Host Controller
    ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
    ohci_hcd 0000:00:13.1: irq 20, io mem 0xff6fd000
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 4 ports detected
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sd 4:0:0:0: Attached scsi generic sg1 type 0
    sr 5:0:0:0: Attached scsi generic sg2 type 5
    ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 20
    ehci_hcd 0000:00:13.2: EHCI Host Controller
    ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
    ehci_hcd 0000:00:13.2: irq 20, io mem 0xff6fc000
    ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 8 ports detected
    piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
    usb 3-2: new high speed USB device using ehci_hcd and address 2
    usb 3-2: configuration #1 chosen from 1 choice
    usb 2-3: new full speed USB device using ohci_hcd and address 2
    rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month
    PPP generic driver version 2.4.2
    8139too Fast Ethernet driver 0.9.28
    ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 19
    eth0: RealTek RTL8139 at 0xf913e400, 00:13:d3:8b:9e:89, IRQ 19
    eth0: Identified 8139 chip type 'RTL-8100B/8139D'
    8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
    usb 2-3: configuration #1 chosen from 1 choice
    ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 21
    firewire_ohci: Added fw-ohci device 0000:02:04.0, OHCI version 1.10
    ACPI: PCI Interrupt 0000:00:14.5[b] -> GSI 17 (level, low) -> IRQ 22
    firewire_core: created new fw device fw0 (0 config rom retries)
    input: PC Speaker as /class/input/input4
    input: ImExPS/2 Logitech Wheel Mouse as /class/input/input5
    parport_pc 00:07: reported by Plug and Play ACPI
    parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    Initializing USB Mass Storage driver...
    scsi6 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 2
    usb-storage: waiting for device to settle before scanning
    scsi7 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 2
    usb-storage: waiting for device to settle before scanning
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    Linux video capture interface: v2.00
    saa7130/34: v4l2 driver version 0.2.14 loaded
    ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 21
    saa7133[0]: found at 0000:02:01.0, rev: 208, irq: 21, latency: 64, mmio: 0xff3ef800
    saa7133[0]: subsystem: 1043:4857, board: ASUSTeK P7131 Dual [card=78,autodetected]
    saa7133[0]: board init: gpio is 0
    input: saa7134 IR (ASUSTeK P7131 Dual) as /class/input/input6
    saa7133[0]: i2c eeprom 00: 43 10 57 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
    saa7133[0]: i2c eeprom 10: 00 01 20 00 ff 20 ff ff ff ff ff ff ff ff ff ff
    saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 cb ff ff ff ff
    saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
    saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 00 ff ff ff ff ff ff
    saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
    saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
    saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
    tuner 1-004b: chip found @ 0x96 (saa7133[0])
    tuner 1-004b: setting tuner address to 61
    tuner 1-004b: type set to tda8290+75a
    lp0: using parport0 (interrupt-driven).
    ppdev: user-space parallel port driver
    tuner 1-004b: setting tuner address to 61
    tuner 1-004b: type set to tda8290+75a
    saa7133[0]: registered device video0 [v4l2]
    saa7133[0]: registered device vbi0
    saa7133[0]: registered device radio0
    DVB: registering new adapter (saa7133[0]).
    DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
    tda1004x: setting up plls for 48MHz sampling clock
    scsi 6:0:0:0: Direct-Access Seagate External Drive PQ: 0 ANSI: 0
    sd 6:0:0:0: [sdc] 312581808 512-byte hardware sectors (160042 MB)
    sd 6:0:0:0: [sdc] Write Protect is off
    sd 6:0:0:0: [sdc] Mode Sense: 27 00 00 00
    sd 6:0:0:0: [sdc] Assuming drive cache: write through
    sd 6:0:0:0: [sdc] 312581808 512-byte hardware sectors (160042 MB)
    sd 6:0:0:0: [sdc] Write Protect is off
    sd 6:0:0:0: [sdc] Mode Sense: 27 00 00 00
    sd 6:0:0:0: [sdc] Assuming drive cache: write through
    sdc: sdc1
    sd 6:0:0:0: [sdc] Attached SCSI disk
    sd 6:0:0:0: Attached scsi generic sg3 type 0
    usb-storage: device scan complete
    scsi 7:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
    sd 7:0:0:0: [sdd] Attached SCSI removable disk
    sd 7:0:0:0: Attached scsi generic sg4 type 0
    scsi 7:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
    sd 7:0:0:1: [sde] Attached SCSI removable disk
    sd 7:0:0:1: Attached scsi generic sg5 type 0
    scsi 7:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
    sd 7:0:0:2: [sdf] Attached SCSI removable disk
    sd 7:0:0:2: Attached scsi generic sg6 type 0
    scsi 7:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
    sd 7:0:0:3: [sdg] Attached SCSI removable disk
    sd 7:0:0:3: Attached scsi generic sg7 type 0
    usb-storage: device scan complete
    tda1004x: found firmware revision 29 -- ok
    EXT3 FS on sda1, internal journal
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sdb4, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sda4, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    Adding 522072k swap on /dev/disk/by-path/pci-0000:00:11.0-scsi-0:0:0:0-part5. Priority:-1 extents:1 across:522072k
    ip_tables: (C) 2000-2006 Netfilter Core Team
    Netfilter messages via NETLINK v0.30.
    nf_conntrack version 0.5.0 (8190 buckets, 65520 max)
    eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
    Unknown InputIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:11:6b:27:96:74:08:00 SRC=192.168.123.254 DST=255.255.255.255 LEN=331 TOS=0x00 PREC=0x00 TTL=64 ID=64771 PROTO=UDP SPT=67 DPT=68 LEN=311
    Unknown InputIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:11:6b:27:96:74:08:00 SRC=192.168.123.254 DST=255.255.255.255 LEN=331 TOS=0x00 PREC=0x00 TTL=64 ID=65027 PROTO=UDP SPT=67 DPT=68 LEN=311
    Marking TSC unstable due to: cpufreq changes.
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=48113 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=48114 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=48117 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Clocksource tsc unstable (delta = -90943342 ns)
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=7077 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=64 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=44
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.130.129 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    Unknown OutputIN= OUT=eth0 SRC=192.168.123.153 DST=195.130.129.161 LEN=75 TOS=0x00 PREC=0x00 TTL=64 ID=31572 DF PROTO=UDP SPT=32768 DPT=53 LEN=55
    My router's IP is 192.168.123.254 but if I ping that address or I try to connect to the web interface on that address to configure the router I can't get any connection...  I've also tried to specify all paramaters directly in rc.conf (eth0="eth0 192.168.123.1 netmask 255.255.255.0 broadcast 192.168.123.255") but that didn't help neither.
    I'm kind of out of ideas on how to solve this... I hope someone here will help me getting out of windows (the only OS on my pc with internet FTM).

    I'm so stupid... I should've thought about iptables... I'm reconfiguring them now, thank you very much!

  • Cisco Connect won't connect to E2000 router

    I've had an E2000 router set up and working fine for years. Today I tried to connect to it with Cisco Connect, as I'd like to enable a separate guest network (incidentally, if there's a way to do this through the web management interface, please let me know!). However, the software fails to connect to the router; the progress bar gets to 25% and then eventually times out. I've tried from multiple computers on the network, both wired and wireless, with the same results. Any suggestions? Thanks!
    Solved!
    Go to Solution.

    Hi A_Generic_User.  I believe there's no way to configure the Guest network through the web ui. What you can do is try using the software that you can download from their site. Make sure to turn off any firewall on the computer when running the software to avoid conflict.  Also, I suggest that you run the downloaded software on a wired PC to avoid wireless interference. Here is the link to the software, http://support.linksys.com/en-us/support/routers/E2000/download . Hope this helps.

  • Share files from 2 computers connected to same router from remote location

    I can remotely (from external IP) share file from one computer connected to my router but I cannot share with other machines on my home network. Same with ARD access. Is there a way to access multiple machines across my router?

    The only easy way to do this would be to use something like Back To My Mac with a MobileMe subscription or [LogMeIn|https://www.logmein.com].
    The problem with what you're trying to do is that your entire home network only has one IP address to the outside world. How did you get it working in the first place? I'm assuming you've got a wireless router and set up port forwarding on the router to redirect traffic to a specific machine. The problem there is that file sharing uses a specific port (548), and you can only map that port to one machine at a time.
    One possibility would be to use different services for different machines. For example, you could share files normally (port 548) on one machine and via FTP (port 21) on another. Another possibility would be to enable screen sharing on the one you can access from outside your home network, then use screen sharing to make that machine log in to the other machines on the network. Of course, neither of these are ideal solutions.

  • WiFi clients suddenly can no longer connect to WRT320N router

    I have a WRT320N router that I have been using for about 3 months now.  I have a mixture of B, G & N clients using Win 2000, Win XP, Win 7, Mac OS X and Linux OSs.  This is my home network.  Everything worked fine until yesterday when, suddenly, none of my wireless clients could connect to the router.  Wired clients were fine.  I tried rebooting machines, resetting the router etc... without success.  I called Linksys tech support and had the tech troubleshoot it.  He got it working again by changing the Wireless Channel Width setting from "Auto (20Mhz or 40Mhz)" to "20Mhz only".  He also changed the channel setting from "Auto" to "9".  This works fine except for my N client where before I was connecting to the router at 240-300Mbps, I am now connecting at 78-117Mbps, less then 1/2 the speed I was connecting at previously.  I called tech support again today and discussed it with a diffrerent tech.  He told me that if my N client was getting over 100Mbps that I was within the specs of the router and that no Linksys router could connect faster than 200Mbps.  Huh?
    My N adapter is a Netgear USB WN111.  The Linksys tech says that maybe that adapter can "suck" (his technical term) more bandwidth from the router than the router should be capable of and suggested I call Netgear to verify that.
    My point is that everything worked fine for the past 3 months at 240+Mbps and now suddenly it doesn't work.  The tech says there must be some sort of interference which seems like a possibility but I live out in the country with no close neighbors and I haven't brought in anything new recently that would explain the sudden problem.
    I think the router developed a hardware problem which is causing it to not perform as well as it did.  Anybody got ant other ideas?

    I would suggest you to reflash/upgrade the router's firmware,reset the router after that and reconfigure it from the scratch..You can download the firmware from www.linksysbycisco.com/downloads.On the linksys setup page,click on the Administration tab to upgrade the firmware.

  • Printer will no longer connect to wireless router.

    My printer won't connect to my router.....I disconnected a Vonage phone from my router, never touched the printer, but since disconnecting the phone, the printer no longer works....I've shut my cable box, router, computer and printer down and re-connected in that order....I've attempted multiple times to connect to the WPS from the printer both by pushbutton and PIN....and I've been unable to find anything on line to help with troubleshooting...any help would be appreciated.  Thanks.

    Hi @MKhelp 
    Thank you for reaching out to the HP Forums, I'd be happy to help you work towards getting your 3054 back online.
    I can help you put the printer on your wireless network without software. I use this method for iPads, iPhones and other devices that do not have software.
    Restore the network defaults on the printer by pushing the wireless button, going to settings, and then restore defaults. The wireless button should then start flashing, this means it is now in autowireless mode.
    Connect to the network that the printer is broadcasting. It is usually HP-setup-3054 and then part of the MAC address. The wireless light will still be flashing on the printer at this point, this is normal since this is not an actual adhoc connection.
    Load up the Embedded Web Server (EWS) in the browser on your mobile device. The default IP for autowireless is 192.168.223.1.
    Go to the network tab along the top of the EWS.
    Click on Wireless Setup Wizard along the lefthand side to begin configuring the printer.
    You have now completed the Wireless configuration, follow the next 3 steps to start printing.
    The blue wireless light will go solid, put the Mac back on your own network.
    Add the printer to the System Preferences.
    Print
    Please let me know if this resolves the issue. Thanks.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • Http 403 error message when connecting to WRT120n router

    I recently upgraded to the WRT120n router at home. I quickly connected my desktop computer, my wife's Mac and two Lenovos, but my son's HP Pavilion cannot access the Internet. It returns the http 403 error message. Windows (Vista) and Network Magic tell me the laptop is connected to the router and the Internet, but the browser does not work. Have tried IE, Chrome and Firefox - same result. Have also tried to connect with cable. Hooking up wirelessly with WPA, was no problem, but the browser is unable to access the Internet.
    Grateful for any help.

    What is the ip address you are getting on the Vista Computer..?
    Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Wireless Network Connection IP Address , Subnet Mask and Default Gateway...
    IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
    If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
    If you get 4 replies then type ping 4.2.2.2 and press Enter, if you get request timed out, then you need to upgrade your router's firmware...If you get 4 replies then type ping yahoo.com and press Enter...If you get replies for Yahoo then you should get the Internet after adjusting the browser settings...
    Adjusting Browser Settings : Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...
    If yahoo times out then provide static DNS on your LAN Connection...
    Click on the Start button >>> Settings >>> Control Panel >>>Network Connections- Right click on the icon for Wireless Network Connection and go to properties- On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button- Select 'Use the Following DNS Settings' Preferred DNS 4.2.2.2 Alternate DNS - 192.168.1.1>>Click on Ok button to Save and Click on "Close" on main Properties window...You should be able to go online... 

  • HT4199 I just got a new iPod touch 4th generation and I'm trying to connect to my router and my iPod says, 'Cannont find network.' I don't know what to do! No other networks come up on the list so I can't 'tag' along with thier wifi. Please help. I need a

    I just got a new iPod touch 4th generation and I'm trying to connect to my router and my iPod says, 'Cannont find network.' I don't know what to do! No other networks come up on the list so I can't 'tag' along with thier wifi. Please help. I need advice.

    What type network is yu router set up for? The 4G iPod can only connect and see 2.4 GHZ networl like B, G and the 2,4 GHz N. There is also a 5 GHz N but the iPod will not even seethat network.
    See:
    iOS: Troubleshooting Wi-Fi networks and connections
    iOS: Recommended settings for Wi-Fi routers and access points

  • LaserJet Pro CP1525nw cannot connect to new router (Home Hub 2000)

    In December, we replaced everything EXCEPT our LaserJet Pro CP1525nw colour printer - new laptop (Dell Inspirion 15), new operating system (Windows 8.1 - 64 bit), new internet provider (Bell) and new wireless router (Home Hub 2000).
    Immediately, we were unable to connect to the router. We tried all of the suggestions, including connecting the printer directly to the router - which worked, until we disconnected it and then they could not communicate again.
    At the time, the only solution we could find was to connect our printer and laptop via USB cable and print that way - no more wireless printing, so unable to print from phones and iPad, but at least we could print from the laptop.
    In the past month, we have become unable to use many of the features on our printer - when we try to select print options, we get the message "HPMSN103.dll has stopped working." So, we can still print, but cannot select options.
    We have tried using the CD that came with the printer, and it gets to a certain point and then a fatal error occurs. We have tried downloading the "full solution" printer install program from the HP website, and the same thing happens. We have tried skipping that and just choosing the appropriate printer driver in Windows: if we only use that driver, we get a printer that shows up, but we cannot print if we select it (interestingly, though, we can actually access the printer options!); if we say we have the disc, then we get two printers showing up - we can select print options on the one that will not allow us to print, but not on the one that actually prints. If we try removing one of the printers, they both uninstall and we're back to square one.
    So, we WANT to be able to get back to printing wirelessly - after all, we paid (handsomely) for a wireless printer! And we still cannot get our printer and the router to recognize each other. Can somebody help? We don't want to have to buy another printer.
    Thanks!

    Hi @Capers2 ,
    I see that you are experiencing issues setting up the printer on the new router. I will certainly do my best to help you.
    Thank you for providing that detailed information.
    If the network name has any spaces or special characters, the printer may not recognize it.
    The printer is only capable of sending/receiving in the 2.4 ghz band.
    If it is set to 5 GHZ network you may need to change to 2.4 ghz. (rename the 5 ghz or shut it off)
    The WPA key setting needs to be on AES to work correctly not TKIP.
    Multi casting needs to be turned on.
    Firewall on router has to have open ports for printer.
    If you have Mac Filtering you need to give printer hardware address from Configuration page.
    You might need to contact your router company for further assistance to check those settings.
    I would reset the printer first to clear out any previous network settings.
    Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
    Print out a configuration report and make sure the SSID and IP address are cleared.
    Printing a Configuration Page.
    The easiest way to setup the printer back on the wireless network is through a Ethernet connection and then switch over to wireless.
    Disconnect the USB cable.
    Remove any printer software by following these steps:
    Go into Devices and Printers , click file then Server Properties, click on the Drivers tab at the top of print Server Properties window. Choose the printer you want to uninstall and click remove. Choose remove driver and package. Any that say Universal PCL 5 or Universal PCL 6 also remove and the Laserjet CP1525nw.
    The next screen will give a warning, letting you know that deleting the driver package will remove it from the system. Click yes to say that you are sure you want to do this. (if the printer isn't listed that is OK)
    Right click and delete any entries for the Laserjet in the Devices and Printers Window.
    Run the uninstall from the CD.
    Press the Windows key and the X key together. and select File Explorer, right click the CD for the
    printer and left click open in new window.
    Connect the printer to the router with a Ethernet cable.
    Wait about 1 minute and the printer should have a valid IP address.
    Print the configuration page to get the printer's IP address to configure the Wireless.
    Type the IP address in Internet explorer's address bar which should open the printer's embedded web services page.
    Setup the wireless through here now.
    Click on the networking tab, wireless on the left, fill out the network information and apply the settings.
    After the confirmation, then disconnect the Ethernet cable.
    Now you should have a blue wireless light on the printer in about 1 minute.
    Perform a clean boot on the computer and turn off the Antivirus Software. How to perform a clean boot in Windows.
    Run the installation again.
    If you are prompted to connect the USB cable during the installation, Then immediately after connecting the USB cable, follow the steps in this document to update the drivers so it doesn't error out. A Fatal Error Displays During Software Installation. Then the installation should continue.
    Test the printer.
    If there is anything else I can help you with, just let me know.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • HP Officejet Pro 8000 Wireless: HP printer unable to connect to wireless router.

    Installing new printer,  getting error msg saying HP printer unable to connect to wireless router.   MAC address filtering may be enabled on your wireless router which can prevent HP printer from connecting to your wireless network during setup.
    SOLUTION says:  If MAC address filtering is enabled and you would like to keep it enabled, you must add the MAC addressof your printer to the list of permitted devices for your wireless router before continuing.
    My router is WD My Net N900 Router. MAC filtering is diabled. My security mode is WPA/WPA2 Personal. 
    I have run out of ideas to try and fix the issues, would appreciate some help.
    Thanks,

    Hi Jamshidk
    I am surprised you are getting that message and you checked the router settings and it is showing that the Mac Filtering is disabled.
    I would suggest connecting the printer to the router with a ethernet cable to get a valid IP address and then setup the wireless.
    Print a configuration report.
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&​dlc=en&docname=c01554589&lc=en&product=3760410&tmp​...
    Type the IP address from the configuration page  in the address bar into internet explorer browser. This will open the embedded web server for the printer. Click on the Networking tab, on the left hand side select wireless. After this is setup and applied, disconnect the ethernet cable.
    Should be on the wireless network. Takes about 1 minute.
    Run the add printer wizard.
    Go to start, devices and printers and select add a printer. (Win 7)
    Test the printer.
    If you need more assistance just let me know.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • GRE tunnel could not be used by the hosts connected to the router

    Hi,
    I am using cisco ASR1013 (RP2) and a Mikrotik Router for setting up a GRE tunnel for LAN to LAN routing over a broadband link. The tunnel works fine (able to ping tunnel end points and also all the connected interfaces on both the Mikrotik and Cisco ASR) but the hosts that are connected directly to the Cisco router interface over a layer 2 cisco switch are unable to connect (ping) the hosts or connected interfaces on the mikrotik side. I am sure its not a mikrotik issue as i dont see any traffic coming through the tunnel using the mikrotik torch utility.  There are no ACL's or firewall rules on any of the devices...... 
    Source and destination of the tunnel are public IP's and are pingable via internet (The tunnel is connected and endpoints are pingable)
    Mikrotik connected interface IP = 192.168.253.1/24
    Mikrotik tunnel end point IP = 192.168.254.1/30
    Cisco tunnel end point IP = 192.168.254.2/30
    Connected cisco subnet to reach Mikrotik = M.N.O.32/28
    Cisco interface IP for LAN = M.N.O.33
    Test host IP on the LAN subnet = M.N.O.34
    The below is my Cisco config
    ASR-1#sh run int tun 1
    Building configuration...
    Current configuration : 144 bytes
    interface Tunnel1
     ip address 192.168.254.2 255.255.255.252
     ip mtu 1400
     tunnel source A.B.C.D
     tunnel destination W.X.Y.Z
    end
    ASR-1#sh run int g0/1/7
    Building configuration...
    Current configuration : 280 bytes
    interface GigabitEthernet0/1/7
     description LAN
     ip address M.N.O.33 255.255.255.240
     ip verify unicast source reachable-via rx
     no negotiation auto
     cdp enable
    end
    ASR-1#sh ip ro 192.168.253.1
    Routing entry for 192.168.253.0/24
      Known via "static", distance 1, metric 0 (connected)
      Routing Descriptor Blocks:
      * directly connected, via Tunnel1
          Route metric is 0, traffic share count is 1
    ASR-1#ping 192.168.253.1 so M.N.O.33
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 192.168.253.1, timeout is 2 seconds:
    Packet sent with a source address of M.N.O.33 
    Success rate is 100 percent (5/5), round-trip min/avg/max = 5/5/6 ms
    ASR-1#pi M.N.O.34
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to M.N.O.34, timeout is 2 seconds:
    Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
    If i try to ping 192.168.253.1 (network connected to Mikrotik) from the host M.N.O.34 (the gateway of this host is M.N.O.33 - Int g0/1/7 of the Cisco ASR), i cannot reach detination - request timed out.... Below are the results of trace and ping from the host connected to ASR G1/0/7
    PING TO THE GATEWAY *********
    [root@localhost ~]# ping M.N.O.33
    PING M.N.O.33 (M.N.O.33) 56(84) bytes of data.
    64 bytes from M.N.O.33: icmp_seq=1 ttl=255 time=0.161 ms
    64 bytes from M.N.O.33: icmp_seq=2 ttl=255 time=0.143 ms
    ^C
    --- M.N.O.33 ping statistics ---
    2 packets transmitted, 2 received, 0% packet loss, time 1357ms
    rtt min/avg/max/mdev = 0.143/0.152/0.161/0.009 ms
    PING TO THE TUNNEL END POINT IN CISCO ASR
    [root@localhost ~]# ping 192.168.254.2
    PING 192.168.254.2 (192.168.254.2) 56(84) bytes of data.
    64 bytes from 192.168.254.2: icmp_seq=1 ttl=255 time=0.141 ms
    64 bytes from 192.168.254.2: icmp_seq=2 ttl=255 time=0.141 ms
    ^C
    --- 192.168.254.2 ping statistics ---
    2 packets transmitted, 2 received, 0% packet loss, time 1739ms
    rtt min/avg/max/mdev = 0.141/0.141/0.141/0.000 ms
    PING TO THE TUNNEL ENDPOINT IN MIKROTIK
    [root@localhost ~]# ping 192.168.254.1
    PING 192.168.254.1 (192.168.254.1) 56(84) bytes of data.
    ^C
    --- 192.168.254.1 ping statistics ---
    11 packets transmitted, 0 received, 100% packet loss, time 10413ms
    PING TO THE CONNECTED INTERFACE ON MIKROTIK
    [root@localhost ~]# ping 192.168.253.1
    PING 192.168.253.1 (192.168.253.1) 56(84) bytes of data.
    ^C
    --- 192.168.253.1 ping statistics ---
    4 packets transmitted, 0 received, 100% packet loss, time 3641ms
    TRACE TO THE CONNECTED INTERFACE ON MIKROTIK
    [root@localhost ~]# traceroute 192.168.253.1
    traceroute to 192.168.253.1 (192.168.253.1), 30 hops max, 60 byte packets
     1  M.N.O.33 (M.N.O.33)  0.180 ms  0.156 ms  0.145 ms
     2  * * *
     3  * * *
     4  * * *
     5  * * *
    Please help

    Hi,
    Sorry for the delayed response ....Both ends static routes are added for the connected test interfaces.....
    Regards,
    Mahesh 

  • I've set up email on my iPad (talk mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this

    I've set up email on my iPad (talktalk.net) and can send and receive mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this?

    I've set up email on my iPad (talktalk.net) and can send and receive mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this?

Maybe you are looking for

  • Limit SC showing Zero value in report SC per cost centre in SRM portal

    Hi SRM Gurus, On executing SC per cost centre report avaialble in SRM 5.0 Portal I am getting value of limit SC as zero. while in all other follow on documents i.e. PO and Invoice its displaying the value. Is it due to the fact the for Limit Items we

  • Can't have multiple wirless devices operating at same time

    I have been trying to figure this out for quite some time now so hopefully someone can help me out. We have two laptops and a wireless printer. My laptop is Vista and my husband's is XP. We cannot have more than one wireless device operating at the s

  • Invoice to 3rd Party System

    Dear Experts, I am trying to send customer invoice to an external system via PI with IDoc type INVOIC02. I have done the basic setting for the output type ZRD0 to transfer the document via. EDI. I have created a partner profile for Logical System u20

  • Sites for UI creation in Photoshop...

    Looking for good sites for UI creation in Photoshop. I already have PSDTuts just wanted some other suggestions. Thanks!

  • Spotlight icon flashing

    After installing 10.6 all the icons in the menu bar that would normally be shown disappear, these are the one that you select from system preferences and also the spotlight icon flashes and i'm unable to use spotlight.