Connection and SMS Problem with Peoples/China Moblie (HK) using iPhone4s

I just signed up with Peoples/China Mobile (HK) service provider for apparently 2.5G service.
I face the following problems which the technical support of the service provider is unable to resolve and providing me any proper feedback:
1) SMS / messaging not working.
- Outgoing SMS all failed.
- Incoming SMS no issue.
2) Unstable and bad connection.
- No service in MTR.
- Upon coming out from the MTR station or location with no reception/elevator, the search for network is slow and service unattainable. The "No Service" sign on the top left screen remain as it is. You have to either restart the phone and force network search again. Very irritating and fustrating.
- Network search subsequent to above incidents are very long (5 minutes at least)
3) Regular service failure for basic phone calls
- Very unstable throughout the days.
Even the basic phone calls and SMS is far worse than my previous service plan. I cant even make/receive proper phone calls. SMS/messaging not working at all!!!!
So what is the root cause?
Iphone 4s glitch or bug? Should I send back to Apple?
or
Problem lies with the Service provider's connection (peoples/china mobile) ? Incompatible phone set versus 2,5G service provider?
Ah Huat
Fustrated customer!!

Your issue is more than likely bandwidth related although there is a lot of variables that can cause issues. You can use the free Speed Test app to test your network speed using your iPhone when the problem arises. This could tell you which end the issue is at. It may be anything from older slower wifi routers, slow Internet connection, which your provider may throttle for certain uses, or network congestion in your area especially if you use cable Internet.

Similar Messages

Can SAP GRC AC 5.3 connect without any problem with SAP R/3 4.7 Enterprise?

hello,
I went to the PAM in the SAP Marketplace to see if SAP GRC AC 5.3 could connect to SAP R/3 4.7 Enterprise but I can't see all the "Add-On Product Version for...", it's cut off.
Can SAP GRC AC 5.3 connect without any problem with SAP R/3 4.7 Enterprise?
If I can't is there any proof about it? I have to show it to a client.
Best Regards,
Pablo Mortera,

Pablo,
GRC AC 5.3 works perfectly fine with SAP's R/3 4.6c, mySAP ERP 4.7 and ECC systems. In fact we have two 4.7 Enterprise systems connected to GRC AC 5.3 system.
You can get the details of supported SAP ERP systems under prerequisite section of Info page of GRC AC 5.3 , it can be accessed on marketplace at -
Downloads-->Installations and Upgrades - Entry by Application Group > SAP Solutions for Governance, Risk, and Compliance>SAP GRC Access Control>SAP GRC ACCESS CONTROL>SAP GRC ACCESS CONTROL 5.3
Just ensure to have proper BASIS and ABAP support pack level as mentioned in prerequisites.
Regards,
Amol

Problem with People Picker field in sharepoint 2013 list

hi friends
i have a problem with people picker
default newitem.aspx
custom NewItem.aspx
why the selection option of the people piker is changing
how can i get the default functionality in custom page
please help me

Hello malli.share,
try to copy source code from newitem.aspx to custom_newitem.aspx (in SPD you can edit custom_newitem.aspx in advanced mode and paste the code).
Regards,
Alexander

I have an iMac OS X 10.6.8 and have problems with the backup Disk for Time Machine disconnecting itself with the message that I ejected it improperly.. It ejected itself - why?

I have an iMac OS X 10.6.8 and have problems with the backup drive to Time Machine ejecting itself and so does not automatically backup the way it is meant to do. It is connected with an USB cable to my iMac. What could cause this - malfuntioning drive?

The "iLife" apps are not part of any Mac operating system install and are a separate purchase.
Once you get past 10.6.6 you can purchase and download iPhoto, GarageBand and iMovie. iWeb and iDVD have been discontinued.
Snow Leopard 10.6.6 and higher include the App Store application which is what you use to purchase Lion.

Services are up and running - problem with browser access to Apps instance

We are using 11.5.10 and I have just finished a clone from our TEST environment.
We cannot connect to the login screen however.
I suspect there is a problem with the address we are using
http://*****.********l.com:8002/OA_HTML/AppsLocalLogin.jsp is the address for our TEST instance. and 8003 was for the previous encarnation of our newly cloned system.
Which configuration file can I check to see how this instance was configured?
I am looking at the adcfgclone returns and see nothing much except
Target system proxy hostname (used default)
Target system proxy port [80]: (left as this)
Should I check the context file for the new instance?
I am checking the webport , but no luck.
Again, in the context file, I see
<oa_web_server>

<hostname oa_var="s_webhost">****cl</hostname>
<externURL oa_var="s_external_url">http://****cl.****.com:8004</externURL>
(8004 was the last port used for this instance before cloning)
Should I check any specific table in the new instance??
Thanks,
DA
Or am I jumping the gun here? Do I need to initialize paraemeters first? (note 216205.1)
Edited by: Dan A on Oct 3, 2008 12:37 PM
Edited by: Dan A on Oct 3, 2008 12:39 PM
Edited by: Dan A on Oct 3, 2008 12:55 PM

Well, checking here oracli3/oracle/devora/iAS/Apache/Apache/logs in the error_log :
I see
Cannot load /oracli3/oracle/devora/iAS/Apache/Apache/libexec/mod_mmap_static.so
into server: A memory address is not in the address space for the process.
But the last date I see is for June (although the file itself is dated from yesterday)
Furthermore, in the error_log_pls, I see similar returns but again, the last date is from August:
Cannot load /oracli3/oracle/devora/iAS/Apache/Apache/libexec/mod_mmap_static.so
into server: A memory address is not in the address space for the process.
Syntax error on line 232 of /oracli3/oracle/devora/iAS/Apache/Apache/conf/httpd_
pls.conf:
Cannot load /oracli3/oracle/devora/iAS/Apache/Apache/libexec/mod_mmap_static.so
into server: A memory address is not in the address space for the process.
...

Why my iphone 4 connect to wifi, but when i open safari and search something it say i not connect.. but in the same house my sister using iphone4 too but she can online with the same router

why my iphone 4 connect to wifi, but when i open safari and search something it say i not connect.. but in the same house my sister using iphone4 too but she can online with the same router. i go and check over the detail of the network i connected, over the ip address and subnet mask have the numbers, but over the DNS and router don't have any number...isit the problem???? i can online at any other place but just my home cant...y????

Hey confuddled_chica!
Try the steps in the article below to troubleshoot this issue:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

I have the new iPad. Even with airplane mode on, my battery life is extremely limited. Is there a problem with the battery? I used to have the ipad2 and had no such problem.

I have the new iPad. Even with airplane mode on, my battery life is extremely limited. Is there a problem with the battery? I used to have the ipad2 and had no such problem.

What is your brightness setting & how many apps are open?
The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom

YouTube and Vimeo problems with Apple TV

Hello,
I own a MacBook Pro with retina display and the most recent version of Yosemite is installed, and an Apple TV which recently automatically updated.
In the last two weeks, I have encountered significant difficulties in trying to play YouTube or Vimeo videos whilst connected to my TV with AirPlay. This issue was not present earlier, and I have owned the Apple TV since September and successfully watched both YouTube and Vimeo videos on extended desktop or by mirroring desktop on many occasions before.
The problem manifests itself as a constant buffering of the video, and will never play. As soon as you disconnect the MacBook from AirPlay the video plays immediately and completely normally. Connect back to AirPlay, and the problem present itself again.
I use Chrome as a browser, but have tried it recently with Safari and I am encountering the same problem.
Can anyone help?

Nevermind with this problem. I saw the other post where someone mentioned updating via wireless rather than wired ethernet. After using the wireless, the update was completed successfully and youtube started working as well.

Broadband connection and speed problems

Hi,
On Wednesday morning my broadband connection went down and could not reconnect from 600am til 700pm. It did manage to get a connection to stay up at around 900pm, but since then the connection has dropped about four times a day.
I have checked my equipment, wiring etc, connected directly to the test socket, using a new ADSL microfilter etc etc. I have also checked for known problems in my area and have done some quiet call tests(17070).
There are apparently no problems in my area, but a couple of the quiet call tests were crackly.
Since last night (Friday) at around 900pm the connection has managed to stay up but my connection speeds, both up and down are much much lower than they used to be.
Since Wednesday night I have performed some BT speedtests.
D/L Profile for my line is - 17.64 Mbps, but actual speed currently varies between around 8 and 11 Mbps.
U/L Profile for my line is - 0.83 Mbps, but speed currenty varies between 0.01 and 0.3 Mbps.
Before Wednesday, my download speeds were typically 16-17Mbps and upload speeds were typically 0.8Mbps.
With very little variation.
I have included some stats from my BT HH3...
Wednesday nights ADSL Line status, after I managed to get a connection to stay up. below;
ADSL Line Status
Connection Information
Line state: Connected
Connection time: 0 days, 04:59:49
Downstream: 18.65 Mbps
Upstream: 443.9 Kbps
ADSL Settings
VPI/VCI: 0/38
Type: PPPoA
Modulation: G.992.5 Annex A
Latency type: Fast
Noise margin (Down/Up): 4.9 dB / 26.4 dB
Line attenuation (Down/Up): 11.1 dB / 5.3 dB
Output power (Down/Up): 20.1 dBm / 12.9 dBm
FEC Events (Down/Up): 0 / 0
CRC Events (Down/Up): 758 / 36
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
HEC Events (Down/Up): 23957 / 6
Error Seconds (Local/Remote): 300 / 4
Current ADSL line status. After the line being up for 17 hours below;
ADSL Line Status
Connection Information
Line state: Connected
Connection time: 0 days, 17:17:36
Downstream: 19.52 Mbps
Upstream: 443.9 Kbps
ADSL Settings
VPI/VCI: 0/38
Type: PPPoA
Modulation: G.992.5 Annex A
Latency type: Fast
Noise margin (Down/Up): 3.2 dB / 28.1 dB
Line attenuation (Down/Up): 11.0 dB / 5.2 dB
Output power (Down/Up): 20.2 dBm / 12.2 dBm
FEC Events (Down/Up): 0 / 0
CRC Events (Down/Up): 133 / 36
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
HEC Events (Down/Up): 636 / 9
Error Seconds (Local/Remote): 117 / 4
One thing that stands out is the Noise Margin of 4.9dB and now 3.2dB. I gather that these values are on the low side. Is 3.2dB acceptable?
I assume my line attenuation values are low as I live very close to my local exchange. I assume that these values are good.
There are some CRC HEC and Error Seconds values. I must admit that I dont fully understand these but I assume these are not good.
One other thing worth mentioning is that the phone cable to my property comes along my front wall over from a neighbouring property. Whilst checking this cable this morning in the daylight, I have noticed that someone, most probably my neighbour, has pulled the cable way from its fixing on the wall in order to put a fence post up on the wall.
The fence post has been there for a few months, with no apparent affect ro my phone and broadband, but I'm concerned that this could have damaged the cable, splitting the shielding or breaking a wire in the cable, or perhaps loosened the connectors to the juntion box it is connected to on the neighbours wall.
Could damage to the cable be the cause of my connection and speed problems?
Also, is it possible that my BTHH3 is faulty?
Any advice would be very welcome.
Thanks
Solved!
Go to Solution.

A little more information.
I have noticed that on a number of occasions when making or receiving voice calls, the broadband connection completely drops. It doesnt happen on all calls, and doesnt seem to happen when just going 'offhook' and listening to a dialling tone.
There is a definite crackle and hiss on most of the voice calls. But only seems to be audible on the home phone.
After a little browsing, I came upon a logging program "Routerstatshub". When I leave this running it logs changes to ADSL stats.
Looking at the logs, I've noticed that when making voice calls, the upstream noise margin always seems to drop considerably, sometimes down to 0dB.
On some calls, both upstream and downstream noise margin drop to 0dB and the broadband connection drops.
I have also noticed that upstream line attenuation increases from around 5dB to around 28dB every hour or so. This doesnt appear to coincide with the voice calls.
CRC and HEC error increase dramatically at the same time as the noise margin changes. HEC goes up by 10s of thousands.
I'm still directly connected into the mastersocket with a new microfilter and no extension cable.
By the way, my connection speeds went down to an all time low yesterday , 1.7Mbps down.
I have now replaced my DECT phone with a corded phone and will make some more voice calls to see if that makes any difference.
Any ideas about what the problem could be would be greatly appreciated.

IOS 7.1 Problem with People Hearing Me

I purchsed my IPhone 5S in December 2013 and never had a problem with people hearing me talk when I called them until I downloaded IOS 7.1. My voice was very faint or you could not hear me at all. I found out through another discussion group that the update may have turned my noise cancellation to off. I checked it out and swtiched it back on and the problem went away and people coud hear me talk again.

Hello All again,
I have found a fix for others that may experience the same issue. The root of my problem appeared to be caused by Bookmarks that were created from Dropped Pins. I use Dropped Pins to Bookmark mostly everything here in Korea because the addresses here are a bit confusing. It appears Apple has updated some Map Data (I could be wrong), and my Bookmarks from Dropped Pins had incorrect addresses. This of course is just my best guess. Bellow is what I did to fix my problem:
I went through each of my Bookmarks one at a time and clicked on them. Instead of clicking on the Car Symbol for directions, I dropped a new Pin right next to the old Bookmark. I then created a new Bookmark from the Dropped Pin and labeled it the same, but with the number 2 so I could determine old from new. After clearing Maps and selecting the new Bookmark, I could then click on the Car Symbol and it would route the directions just fine. After verifying the new Bookmark worked properly, I deleted the old Bookmark. Rinse and repeat for all of my Bookmarks, re-ordered them and now its as if I never had a problem in the first place. Tedious work, but managed to solve my problem. I hope this helps for anyone else that may have the same problem.
Have a good day.

Mail and iPhoto Problems with sending photos.

Mail and iPhoto Problems with sending photos.
I have this problem that started a while ago and seems to be getting worse.
Here are the different scenarios.
-If I try to share a photo to email within iPhoto, it will insert the image file name in the mail message, but no image icon or opened image. In iPhoto Preferences under General I have chosen to use Email Photos using Mail.
-If I choose to use iPhoto to send the photo, it will compose the message and the photo is viewable. If I send the message i can view the photo within the email I sent to myself. Nothing happens when I double click on the photo in the Mail message. Nothing happens when i control click on the photo in the mail message. Nothing happens when I try to drag the photo to the desktop from the mail message. When I try to save attachments from the email and choose a place to save it, the save button is grayed out and it cannot be saved. When I check the mail message it says there is an attachemnt but there is no file size listed.
-If I use the stationary within Mail app I cannot drag a photo into the placeholder, I get a circle with a line through it symbol when I try. It happens if I try to drag a photo from the desktop or from the media browser within Mail app.
-If I drag the photo to the desktop from iPhoto, I can double click it on the desktop and it will open in Preview.
-If I then control click on the same photo on the desktop and scroll to share/email, the generic photo icon will be inserted in the mail message. If i double click the photo icon in the mail message I get a message it can't be opened because it is empty.
-If I drag that same image to the mail message body the same thing happens.
-If I send that email to someone they cannot open the image file.
What I can do:
- I can drag that same image file on the desktop to my dropbox folder and it will upload. From there I can go on my iPad and download the photo and send it through email just fine.
-I can open the same image file on my desktop in Preview, I can copy and paste it into a mail message and the image will be viewable in the mail message by me and by the recipient.
-I can drag that same image on the desktop to my safari browser window and it will be viewable in the page. i can then copy and paste that image into a mail message and it is viewable in the message. I can then send that email message to myself and i can control click on the image and get all my options. It also shows as an attachment with the size of the image file in the mail message.
I can send that message to someone and they can see the photo and open it fine.
-If I send that same email to me I can see the photo within the mail. If I then drag that photo to the desktop I cannot use it again to put in an email as the same problem happens again.
I have tried all scenarios in my user account, another users account and in a guest account. The same happens in all. I am guessing because of this it is not a corrupt preference file, unless all of the preference files are corrupt. The guest user account I added a new email account so it was brand new and still had the problem.
I am stumped, all and any help is appreciated.

Another problem that may be related….
I have Snapz Pro. I used to be able to save the snaps to my desktop or a folder. Now when I take a screenshot and try to save the file to my desktop or a folder on my desktop I get this message "Files cannot be created in the selected location. You do not have permission to write to the selected location. Please choose a different location." I have found that i can only save the file to the clipboard. I have repaired permissions many times and still I have this problem.

I have a 17" Macbook pro with flickering red and cyan(blue) lines across the screen. The issue disappears temporarily when I tap on the computer, and the problem does not occur when I use external display or try to screen capture the problem.

I purchased my Macbook (17") through a certified apple tecnition in August 2012, it was refurbished and the motherboard was completely replaced. I do a lot of photo editing, but I have been unable to do so because of the red vibrating lines that interrupt my screen. The issue disappears temporarily when I tap on the computer, and the problem does not occur when I use external display or try to screen capture the problem. I brought the computer back to the technition I purchased it from and he said that it was a problem with my fan, so I have two new fans but the issue is still occuring. He says he doesnt know whats wrong. Does anyone have any information on this issue?
Here is an image of the issue
http://www.flickr.com/photos/67839707@N08/8884847081/

I recommend having your Mac serviced by someone competent. A force sufficient to "blow apart" the fans was clearly excessive and may have damaged the display cable, as well as any number of other problems.
Dust is properly cleaned with a vacuum, preferably one designed for computer service, and they are not cheap.
Compressed air should never be used. It just blows dust everywhere, often into places where it can no longer be removed.

I have bought Adobe Photoshop Elements 10 last August 2013 and having problems with installing it on Windows 8.1?

I have bought Adobe Photoshop Elements 10 last August 2013 and having problems with installing it on Windows 8.1. Why am I having this problem?

You can check you Adobe account online to see if the serial number is registered under your account. If not then your only option will likely be to contact Adobe Support directly thru chat to see if they can provide you with a/the serial number. For them to do so will require you being able to prove ownership.
Serial number and activation chat support (non-CC)
http://helpx.adobe.com/x-productkb/global/service1.html ( http://adobe.ly/1aYjbSC )

I have Iphoon 4 and ihave problem with speaker what i have to do?

I have Iphoon 4 and ihave problem with speaker what i have to do?My problem is no body can heir me.
I have got my IPhoon from London U.K. Now i'm in Saudia Arabia

If it's happening on all the apps that you've downloaded from the App Store, but not the Apple built-in ones, then try downloading any free app from the store (as that appears to reset something) and then re-try them - the free app can then be deleted.
If it's happening on all apps then try closing them all completely and then see if they work when you re-open them : from the home screen (i.e.not with any app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of each app to close them, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
If that doesn't work then you could try a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

I have ipad 2 and facing problem with programs swtching off

I have ipad 2 and facing problem with programs it's swtching off while working and turn to home page. Am using ios 5

If it's happening on all the apps that you've downloaded from the App Store, but not the Apple built-in ones, then try downloading any free app from the store (as that appears to reset something) and then re-try them - the free app can then be deleted.
If it's happening on all apps then try closing them all completely and then see if they work when you re-open them : from the home screen (i.e.not with any app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of each app to close them, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
If that doesn't work then you could try a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Connection and SMS Problem with Peoples/China Moblie (HK) using iPhone4s

Similar Messages

Maybe you are looking for