Connection help required

hi e1
i have developed a chat application to chat online through mobile
it is running perfect on my system
i installed it on my device
but when i try to connect through mobile
it gives a error
Connect SymbianOS error=-33: System error
it is server timeout error
i even increased tomcat server timeout in server.xml
but still same error
i am using HTTP Connection
please help me to come out of this problem(it is urgent)
thanks

hariii
i am facing the sam problem with Nokia 6600 some time before, its open the yahoo, google etc but not make a connection through my j2me application and through same error then i talked with operator and get a full GPRS support. Might be you also facing the same issue.
Ashish

Similar Messages

  • Laptop to ultra 10 connection help required

    Hi ,
    I recently purchased a used ultra 10 for trying out , but i get no display on my monitor. I assume the display card is not working.
    I would like to connect it to my laptop (IBM T42). I used hyperterminal along with a serial cable but i dont get any display on my laptop.
    Can you guide me with which cable i should use (i dont know much about cables so pls try to elaborate for me.)
    and do i have to do any other settings.
    Any help is apprecaited

    The Sun systems have a 25 pin female RS-232 connector while PCs have a 9 pin male connector. If you buy a Null-Modem cable you'll usually only find cables with 9-pin plugs on both ends.
    If you want to solder the cable yourself you do not need to solder a "complete" Null-Modem cable; a so-called 3-wire cable is enough.
    The pinning is:
    PC (9 pin female)               SUN (25 pin male)
        2 (RX) ------------------------ 2 (TX)
        3 (TX) ------------------------ 3 (RX)
        5 (GN) ------------------------ 7 (GN)Typically the SUN has the following serial port settings:
    9600 bauds, 8 bits/byte, no parity, 1 stop bit
    Martin

  • Help required with (soundcard) connection / settings, thanks in advan

    Help required with connection / settings between a Creative Sound Blaster Audigy Platinum EX (soundcard) and a Creative DTT3500 Digital (5. speakers).
    The problem
    No sound from any of the speakers. (Exception can plug in headphones at front)
    Background
    My computer has been recently upgraded at my local computer shop and all programs re-installed (including driver update from Creative's website). However after reconnecting speakers and restoring the original settings I?m getting no sound from any of the speakers. I?ve followed all the available advice/instructions I can find on this website and manuals to no avail.
    Set-up
    Physical
    (Digital DIN) Speakers/decoder amplifier (DTT3500) connected to the (digital out) soundcard (Audigy Platinum EX) using minijack to DIN cable. (As per instruction manual)
    Software
    Creative Audio Consul ? setting as per instructions, however have tried variations in vain. (Note: above tabs there is a select device box with SB Audigy [A0000] in it ? only option. Just wondering what [A0000] means?)
    Your advice please. A simple step by step guide would be appreciated, many thanks in advance, Jon

    "My computer has been recently upgraded at my local computer shop and all programs re-installed (including driver update from Creative's website). "
    Do you have the original installation disk?
    If so, try installing THOSE drivers, ESPECIALLY if it worked before. Be sure to uninstall what is there now, first.
    Its natural for most people to want the 'latest' drivers for their hardware. However:
    After experiencing some difficulties with some CL 'updates' for certain products, I now avoid them UNLESS I am having a PROBLEM with the existing drivers.

  • My new ipad is showing the message 'Use wi fi to restore - A wi fi connection is required to download your apps and media' then gives 2 buttons

    I had my ipad replaced last week. The apps etc were transferred to the new ipad and it worked fine for a couple of days. This morning the screen locked up and displayed the message - Use WiFi to Restore- A wi fi connection is required to download your apps and media. Then gives a choice of two buttons - Later or Use Wifi. Absolutely nothing happens when you press these buttons, the whole screen has locked up and it can't even be turned off. If you hold the off button down then eventually the slide to power off button appears but nothing happens when you swipe it. Help!

    Hold down the home button and power button at the same time, ignore the power off slider until the Apple logo appears.

  • Help required network configuration - Gateway route settings get erased on reboot.

    Oracle Linux 7
    Linux myhostname 3.8.13-35.3.1.el7uek.x86_64 #2 SMP Wed Jun 25 15:27:43 PDT 2014 x86_64 x86_64 x86_64 GNU/Linux
    #cat /etc/sysconfig/network-scripts/ifcfg-eno16780032
    TYPE="Ethernet"
    BOOTPROTO="none"
    DEFROUTE="yes"
    IPV4_FAILURE_FATAL="no"
    IPV6INIT="yes"
    IPV6_AUTOCONF="yes"
    IPV6_DEFROUTE="yes"
    IPV6_FAILURE_FATAL="no"
    NAME="eno16780032"
    UUID="2d1107e3-8bd9-49b1-b726-701c56dc368b"
    ONBOOT="yes"
    IPADDR0="34.36.140.86"
    PREFIX0="22"
    GATEWAY0="34.36.143.254"
    DNS1="34.36.132.1"
    DNS2="34.34.132.1"
    DOMAIN="corp.halliburton.com"
    HWADDR="00:50:56:AC:3F:F9"
    IPV6_PEERDNS="yes"
    IPV6_PEERROUTES="yes"
    NM_CONTROLLED="no"
    #route -n
    Kernel IP routing table
    Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
    0.0.0.0         34.36.143.254   0.0.0.0         UG    0      0        0 eno16780032
    34.36.140.0     0.0.0.0         255.255.252.0   U     0      0        0 eno16780032
    169.254.0.0     0.0.0.0         255.255.0.0     U     1002   0        0 eno16780032
    When I reboot the machine, the first line in route table gets erased, I then run:
    #route add default gw 34.36.143.254
    After which network works fine.
    Help required. I don't want to use NetworkManager.

    The following might be useful:
    https://access.redhat.com/solutions/783533
    "When transitioning from NetworkManager to using the network initscript, the default gateway parameter in the interface's ifcfg file will be depicted as 'GATEWAY0'. In order for the ifcfg file to be compatible with the network initscript, this parameter must be renamed to 'GATEWAY'. This limitation will be addressed in an upcoming release of RHEL7."
    NetworkManager is now the default mechanism for RHEL 7. Personally I don't quite understand this, because as far as I can gather it is a program for systems to automatically detect and connect to known networks. I think such functionality can be useful when switching between wireless and wired networks, but for a server platform, I wonder.

  • IPad Air - The connected device requires too much power.

    When connecting my iDJ Live II to my new iPad Air  I receive the following message:
    Cannot Use Device
    Numark iDJ Live II: The connected device requires too much power.
    The iPad Air is running iOS 7.0.4, I also have an iPhone 5S, iPad Mini and iPad 2 all running latest iOS 7.0.4 and this dj controller runs on all these models. I know about the 20mA output limit on these other devices but they all still work why not the iPad Air? What has changed?
    I am very disappointed with this restriction as the only reason I bought the iPad Air was for the better processing power and 128gb storage to fit all my music on there to use this dj controller with djay 2 and vjay. Now I have spent $900 on something I can not use as intended.
    Please any help would be appreciated.
    Thanks
    Adam

    Try giving your iPad a reset. See if it can clear up the error or if it repeats. Hold down the sleep and home keys until it reboots then try again.
    How does this device plug in? Via the lightning connector or the USB part of the camera kit? If it's USB then sometimes a powered USB hub can help with the power issues.
    If it's lightning then the issue could be related to something that came with iOS7. Due to so many unauthorized lightning cables, iOS7 activated software that looks for a code broadcast by the chip in the lightning connector. Authorized manufacturers have codes that the software sees, unauthorized ones don't. Usually people using unauthorized cables get a specific message, however it could be possible that this new part of the software is affecting other things connected to the lightning port.
    Have you looked on djay's site to see if others are having issues or if they have fixes?

  • Just installed Premiere Elements, tring to register I'm getting this message:Either your computer is offline or the clock on your computer is set incorrectly, causing a connection error. An Internet connection is required. Please connect to the Internet o

    Just installed Premiere Elements, tring to register I'm getting this message:Either your computer is offline or the clock on your computer is set incorrectly, causing a connection error. An Internet connection is required. Please connect to the Internet or adjust your clock and try again.". Have tried all suggested steps, no problem registering PSE  one month ago. Win 7 system. Is there a solution?

    Laurenceb70597335 you can find details regarding the activation process at Activation & Deactivation Help.  This includes details on how to activate and deactivate Premiere Elements.

  • RV220W - VLAN help required

    Hi,
    I am having an issue with a new vlan on this router. The router is using the default firmware 1.0.0.26 as I cannot use 1.0.1.0 as we have a DSL connection which required PPPoE.
    VLAN1 is for the our work PC's and our SBS which also acts as the DHCP server. The router is set with a static address and has the DHCP disabled.
    VLAN5 is for a group of PC's which are only to have access to the Internet and nothing else on the network. I have done some screenshots of the settings.
    When I connect a PC to port 4, a valid IP is not recieved from the DHCP set up for VLAN5, instead the PC recieves an IP address from SBS which is on VLAN1, it also shows that I am connected to the local domain on VLAN1. Am I missing something, is there anything else which needs settings. I can't figure out why I am not getting a 192.168.5.0 address.
    My wireless secure VLAN10 works fine, and recieves the correct IP address.
    Any help would be appreciated.
    Michael.

    Michael,
    Well have been reviewing your posts and also set similar configuration in our lab. Note that i did have some trouble; no trouble with the RV220W but rather the switch was shutting down one of the connected ports to RV220W. So i went into SG-302 switch and disabled STP on that port and everything started working fine. So, this is most likely similar in your case as well. Also if the netgear is a fully managed switch why don't you just truck both vlan's on the same port. This will free up two ports in your network. you mentioned that you were getting an ip address from vlan 1 when you were connected to vlan 10, even with your configuration file i did not experience anything like this. On the wireless side you might want to reconnect to each SSID and test. When testing you want to make sure you do a (ipconfig /release) and (ipconfig /renew) your IP stack might be keeping settings from your pervious connected network.
    Thanks,
    Jason Bryant
    Cisco Support Engineer
    .:|:.:|:.

  • My ipad was is displaying an alert message " A wi-fi connection is required to download your apps and media". So it has been connected to the internet over night and this morning but is still displaying the alert message and it won't go away. what to do?

    Hi,
    My name is Norbert. I am having some difficulties restoring my icloud back up. My ipad was doing an icloud back up and the alert message displayed on the ipad after my internet was interrupted "A wi-fi connection is required to download your apps and media".
    I got the internet working, my ipad is receiving internet network but the alert message is still displayed on the ipad and won't go away, to make matters worse the ipad is frozen and i can't do anything.
    Please can anyone with a similar experience tell me what to do in this situation?
    Thank you

    Welcome to the Apple Community.
    Have you tried a hard restart. Press the on/off button and homescreen buttons together until the device shuts down.

  • XSLT mapping Help Required.

    XSLT mapping Help Required.
    Hi Experts,
    I am New to XSLT Mapping. I am practising the below Example:
    InputXML File:
    <?xml version="1.0" encoding="UTF-8"?>
    <?xml-stylesheet type="text/xsl" href="Persons111.xsl"?>
    <ns0:MT_XSLT_Source xmlns:ns0="http://XYZ.com/gen">
    <Person>
    <FirstName>Anshul</FirstName>
    <LastName>Chowdhary</LastName>
    <Gender>Male</Gender>
    <Address>
    <Street>2nd Main</Street>
    <Houseno>83/b</Houseno>
    <City>Mysore</City>
    </Address> </Person>
    </ns0:MT_XSLT_Source>
    XSL StyleSheet File:
    <?xml version='1.0' encoding="UTF-8"?>
    <xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:ns0="http://XYZ.com/Gen"
    Xmlns:ns1=”http://XYZ.com/Test”>
    <xsl:template match="/">
    <ns1:MT_XSLT_Target>
    <Title> <xsl:value-of select="ns0:MT_XSLT_Source/Person/Gender"/> </Title>
    <Name> <xsl:value-of select="concat(concat(ns0:MT_XSLT_Source/Person/FirstName,' '), ns0:MT_XSLT_Source/Person/LastName)"/>
    </Name>
    <Street> <xsl:value-of select="concat(concat(ns0:Mt_XSLT_Source/Person/Address/Houseno,' '),
    ns0:Mt_XSLT_Source/Person/Address/Street)"/> </Street>
    <City> <xsl:value-of select="ns0:Mt_XSLT_Source/Person/Address/City"/> </City>
    </ns1:MT_XSLT_Target>
    </xsl:template>
    </xsl:stylesheet>
    The Desired Output shuold be:
    <?xml version="1.0" encoding="UTF-8"?>
    <ns1:MT_XSLT_Target xmlns:ns1="http://XYZ.com/Test">
    <Title>Male</Title>
    <Name>Anshul Chowdhary</Name>
    <Street>83/b 2nd Main</Street>
    <City>Mysore</City>
    </ns1:MT_XSLT_Target>
    I have refered the xsl in xml and i am getting the below Oupt in a Single line like this:
    Anshul Chowdhary Male 2nd Main 83/b Mysore
    I am Unable to display in Target XML Fomrat as shown above. Please check and do the needful.
    Regards,
    GIRIDHAR

    Hi,
    I have used below for testing.
    Input xml:
    <?xml version="1.0" encoding="UTF-8"?>
    <?xml-stylesheet type="text/xsl" href="Persons111.xsl"?>
    <ns0:MT_XSLT_Source xmlns:ns0="http://XYZ.com/gen">
    <Person>
    <FirstName>Anshul</FirstName>
    <LastName>Chowdhary</LastName>
    <Gender>Male</Gender>
    <Address>
    <Street>2nd Main</Street>
    <Houseno>83/b</Houseno>
    <City>Mysore</City>
    </Address> </Person>
    </ns0:MT_XSLT_Source>
    xsl code:
    <?xml version='1.0' encoding="UTF-8"?> 
    <xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:ns0="http://XYZ.com/gen" 
        xmlns:ns1="http://XYZ.com/Test"> 
        <xsl:output method="xml" version="1.0" encoding="UTF-8" indent="yes"/> 
        <xsl:template match="/"> 
            <ns1:MT_XSLT_Target> 
                <Title> <xsl:value-of select="ns0:MT_XSLT_Source/Person/Gender"/> </Title> 
                <Name> <xsl:value-of select="concat(concat(ns0:MT_XSLT_Source/Person/FirstName,' '), ns0:MT_XSLT_Source/Person/LastName)"/> 
                </Name> 
                <Street> <xsl:value-of select="concat(concat(/ns0:MT_XSLT_Source/Person/Address/Houseno,' '), 
                    /ns0:MT_XSLT_Source/Person/Address/Street)"/> </Street> 
                <City> <xsl:value-of select="/ns0:MT_XSLT_Source/Person/Address/City"/> </City> 
            </ns1:MT_XSLT_Target> 
        </xsl:template> 
    </xsl:stylesheet>
    For testing in PI ,change the extension from .txt to .xsl and zip it and upload into PI as an imported archive .
    Regards
    Venkat

  • Urgent help required: Query regarding LC Variables

    Hi All
    Sometime earlier I was working on a performance issue raised by a customer. It was shell script that was taking almost 8-9 hrs to complete. During my research I came across a fact that there were some variables which were not set, the LC variables were impacting the sort funnel operations because of which the script was taking a long time to execute.
    I asked them to export the following commands, after which the program went on smoothly and finished in a couple of mins:
    export LC_COLLATE=en_US.ISO8859-1
    export LC_MESSAGES=C
    export LC_MONETARY=en_US.ISO8859-1
    export LC_MONETARY=en_US.ISO8859-1
    export HZ=100
    export LC_CTYPE=en_US.ISO8859-1
    export LANG=en_US.UTF-8
    Later I did recover that setting the LC_COLLATE to C, is not helping and the program was again taking a lot of time. Few questions that I want to ask are:
    1. Can someone please tell me, what each of these variable mean and how these values make a difference.
    2. When I exported LC_COLLATE=en_US.ISO8859-1, it worked fine, but when i tried with the defalut value LC_COLLATE=C, then why the program didnt work.
    As this issue is still going on, hence I would request All to provide their valuable inputs and let me know as much as possible.
    Appreciate your help in this regard.
    Thanks
    Amit
    Hi All
    A new development in this regard. The customer has send us a screen shot in which they were trying to export the locale variable using the commands which I have pasted above. I can see in the screen shot that while exporting LC_COLLATE and LC_TYPE, they get a message that ""ksh: export: couldn't set locale correctly"".
    Request everyone to please give their inputs as it's a bit urgent.
    Thanks for all the help in advance.
    Thanks
    Amit
    Some help required please...
    Edited by: amitsinhaengg on Jul 22, 2009 2:03 AM
    Edited by: amitsinhaengg on Jul 22, 2009 2:06 AM

    LC_CTYPE
    Controls the behavior of character handling functions.
    LC_TIME
    Specifies date and time formats, including month names, days of the week, and common full and abbreviated representations.
    LC_MONETARY
    Specifies monetary formats, including the currency symbol for the locale, thousands separator, sign position, the number of fractional digits, and so forth.
    LC_NUMERIC
    Specifies the decimal delimiter (or radix character), the thousands separator, and the grouping.
    LC_COLLATE
    Specifies a collation order and regular expression definition for the locale.
    LC_MESSAGES
    Specifies the language in which the localized messages are written, and affirmative and negative responses of the locale (yes and no strings and expressions).
    You can use command
    # locale -k LC_CTYPE
    to see more detail about each type.

  • Help required - Sales order item is partially delivered but the item grayed

    I have a sales order 123 having say item10 with qty 1, item20 with qty 10 , item 30 qty 12
    Item 1 confirmed qty 1 and delivered qty is 1
    Item 2 confirmed qty 10 and delivered qty 10
    Item 3 confirmed qty 1 and delivered qty is 1
    Now the item3 still has open requirements of 11 to be delivered. But the item is GRAYED OUT already.
    even if I do ATP the qty is not confirming for the remaining 11 pieces.
    Why is that? How to make that item out from GRAY.
    How to confirm the remaining 11 qty for that item.
    Help required as early as possible.
    Appreciate ur help guys
    Radha

    hi Radha, how are you ?
         ---the partial deliveries in master data must have not been mentioned.
         ---the deliveries should be upto target quantity.
         ---check order type, item category and schedule line category.
         ---check unrestricted stock availability.
    thank you
    regards
    Khera.

  • Since upgrade to IOS 10.9 and associated iTunes 11.1.3, I can no longer WiFi sync iPad (IOS 7.0.3) nor iPhone (IOS 6.1.3).  USB connection is required.  Formerly I could sync both devices without locating them physically (not necessarily charging).

    Since upgrade to OS 10.9 and associated iTunes 11.1.3, I can no longer WiFi sync iPad (IOS 7.0.3) nor iPhone (IOS 6.1.3).  USB connection is required.  Formerly I could sync both devices without locating them physically (not necessarily charging).  I have restarted both devices, turned off and on "Sync with this iPad/iPhone over WIFI" and restarted WiFi.  WiFi is operating (iPad has no SIM).  What next?

    I'm also affected by this bug in exactly the same way as you.
    Some users have had success by closing iTunes, enetering (on OS 10.9) settings --> network --> edit locations, then create a new location with the same wifi/network settings. Then restarting iTunes.
    Others have had some success by editing settings --> iCloud --> de-selecting keychain
    neither of these fixes have worked for me.
    It appears that the iPad can "see" iTunes running on my iMac because when I open settings --> general --> 'iTunes wifi sync', "sync now" is greyed out if iTunes is not running. When iTunes is started, "sync now" is enabled but just doesn't work. Nor does the iPad appear in iTunes.

  • Search Help with in a serach help required in SRM 4.0

    Hi,                                                     
    Requirement: Search help required for Product Category field in the Search help for Product(BBPH_PRODUCT) in SRM portal.
    This search help is used in Create shopping Cart transaction. The hyper link on Internal Goods/Services leads to the search help BBPH_PRODUCT. 
    My analysis:           
    The field Product Category (CATEGORY_ID) has search help(COM_CAT_HIER) attached to its data element. When I single test the search help BBPH_PRODUCT in SAP GUI,I can see the search help for field product category in the selection dialogue box. However the same does not appear on the corresponding screen in HTML.
    Please let me know whether I need to do some thing to make the search help appear on the HTML screen?
    With Regards,         
    Prakash Kamath

    Hi Prakash,
    I have the same problem but with another field. Unloading point. Could you please tell me how did you solve this problem with displaying F4 help on html/ SRM portal?
    Thank you very much.
    Best regards,
    Danijela ZIvanovic

  • Help required with Photoshop Elements 4.0 this has been installed on my new Toshiba laptop with windows 8.1 for some 18 months and operating well. Now it will not open, message pops up saying "attempt to access invalid address" then "application not respo

    Help required with Photoshop Elements 4.0 this has been installed on my new Toshiba laptop with windows 8.1 for some 18 months and operating well. Now it will not open, message pops up saying “attempt to access invalid address” then “application not responding” Suggestions how to access would be much appreciated. Tks. Stuart

    What is the size of your hard disk?  PSE 4 is a very old program and I suspect it is not able to access the entire hard disk on your machine.  Just a thought here.

Maybe you are looking for