Connection Message Popup

I have two HP printers, Photosmart 2575 and D7400. One is on its own wireless connection, the other is on a Homeplug network connection. I have a third Brother laser printer also connected through the same homeplug and a hub. The HP printers CONSTANTLY popup a message that they are connected/disconnected/connected. I never have any problem printing to them, and the 2575 works great as a networked scanner. The messages are non-functional, the info is meaningless and very annoying, as it takes up a significant amount of screen space and stays way too long. How do I turn it off? There should be a setting in HP Solution Center. The only assistance I have received from HP directly is to turn off any HP item in msconfig. (Windows XP Home.) Doing this finally stopped the message, but the printers were offline until I turned everything back on. (I turned them off one at a time with no effect until the whole system was disabled.)
(The D7400 does not give this message at this time because it is turned off.)

I note that no one has replied to this message in 7 months, but I hope that someone knows the answer. I have the identical problem as the OP. I have two networked HP printers and recently updated the driver and some utilities (listed by HP as critical) for one of the printers. Since then I have a constant parade of popup messages: "Your printer is connected" - "Yours printer is disconnected" - "Your printer is connected" - and so on every few minutes. Very annoying and no way to turn it off. Incidentally, the messages are incorrect as the printer seems to be available all times. The messages even pop up while the printer is running!
I only way I can guess to stop this is to forget about all the utilities that HP said were critical and roll back to the original driver. Does anyone know a better way?
Thanks,

Similar Messages

Internet Connection Message at startup and various moments of the day

I started out using a dial-up connection, then later upgraded to ethernet. Now, everytime I start up my iMac I get a Internet Connection message. Here's what it says, The selected communications device does not exist. Please verify your settings and try again. I click ok and my wirless still works. Then, later during my session I get the message again. Any thoughts on how to get rid of this message? Thanks in advance.
p.s. is this the right place for this question?
Thanks,
mdawg

Yes, this is the right place for such a question.
The issue with your problem is working out specifically which 'communications device' the Mac is complaining about. It's presumably the modem, but that's not necessarily the case.
The first place to look would be in System Preferences -> Network.
What network ports are enabled there? If the modem is still listed and is the preferred connection (it's at the top), then the Mac is going to try to use the modem and fall-back to the ethernet network if the modem fails.
If that is the case the solution is simple - just use the Show popup menu in Network Preferences to select Network Port Configurations. Here you can enable and disable different ports, as well as change their priority (by dragging them up/down).
Either drag the ethernet port to the top of the list or, if you never expect to go back to the modem, disable the modem option.

Message Popup crashes TestStand

Hello,
Our sequence executes under TestStand 3.5 ; steps call dlls written with LabWindows/CVI 7.1.1.
Everything is going fine except some calls to the "Message Popup" step
of TestStand : sometimes TestStand crashes on such calls (we have to
stop it from Windows Task Manager). We have several "Message Popup" to
display during the sequence execution and we have noticed that the
application does not systematically crash on the same Message Popup
step.
The target computer is a PIV 3.2 HT with 1Gb RAM.
Does anybody have the same problem ?

Hi,
We have installed CVI8.0.0.273 runtime engine and we still have crashes on some Message Popups in SeqEdit.
Here is a short description of the system : we have a PXI 1000B chassis connected to the computer with a PCI and a PXI MXI-3 (software v1.15).
PXI cards : 2 PXI CAN 8461/2 (one dedicated to DiagOnCAN and the other one for CAN), 1 PXI 6070E, 1 PXI 6713, 1 PXI 6704, 1 PXI GPIB. We also have 2 PCI cards : Addi-Data APCI 2032 which drive the relays of the system. We have installed DAQ-mx 8.0 (DAQ 7.4.0 is also used on the system for an other application, not with TestStand), NI-488.2 2.43 and NI-CAN 2.3.2.
Our application is multithreaded (3 threads + 1 main thread).
We have tried several solutions not to use the step "MessagePopup" of TestStand : we have created a specific step calling a CVI dll. In this dll we call the CVI MessagePopup function, but TestStand still crashes. Next we have tried to display a panel (created in a uir file) instead of the Popup but the problem is not solved (we tried several combinations of panel attributes).
In Windows TaskManager we see that the PIV 3.2GHz HT is never overloaded (CPU load = about 90%) and that there is enough memory available on the system.
If we try to run a sequence that creates 3 threads which process nothing (infinite loops), with no signals / CAN / instruments processing, we can't reproduce the crash caused by the Popups.
Do you have any suggestion about that ?

Modal message popup is causing TestStand ActiveX error

When I execute a modal Message Popup step, I get the following error:
ActiveX Error
sCode = 0xffffbba4
Source: TSAPI
Description: Could not connect to TestStands TSSync server.
If the Message Popup is not modal, the sequence executes just fine.
I am making the Message Popup modal by selecting the "Make Modal" option.

There is a call to TS_StartModalDialogEx function in the \API\CVI\tsutil.c file which in turn calls into the engine. The engine needs the sync server to implement the modality. I would assume that the file \bin\TSSync.dll is missing or not registered. You can register the dll by running "regsvr32.exe \bin\TSSync.dll". See if this fixes your problem.
Scott Richardson
National Instruments

Deal with teststand message popup

when I add a message popup in my sequence,I need two button: Ok(button1) and Cancel(Button2).and set timeout.
My question is like this; I need get the status when execute,if uesr click ok,the sequence should go to next step,the other stauts,the sequence should abort executing.
example:
Message Popup
if(RunState.Sequence.Main["Message Popup"].Button1Label=="OK")
call sequence //this action need execute when click "OK"
else
break //this is a action ,without any connection of message popup
end
but no matter what button I click ,the sequence always execute break,that's means the if condition can't get the status of message,where is my error.
any one help me ,thanks very much

duplicate post see the following link
http://forums.ni.com/ni/board/message?board.id=330&message.id=21602&jump=true
Regards
Ray Farmer

How to open a message popup and keep the sequence running ?

I have some steps in my sequence to initialize communication ports that takes a few seconds. As i have the trace off i want to display a message popup to tell the user that the sequence is doing the init. After the init steps are done i want to close the popup out of the sequence without pressing any button.
Is there a possibility in TestStand to do this ?
The normal Message popup stays until a key is pressed and even pauses the sequence while active.
Thank for help.

You could call your message popup in a subsequence as new execution and terminate this execution programmatically after your init steps have finished.
In order to do this you have to specify (module) the sequence call step that calls your subsequence:
-Multithreading and Remote Execution = Run in a New Execution
-Settings: Initally Hidden and Tracing disable, Restartable, Close Window when done, Wait for Execution to complete: Do not wait, Process Model Option: Do not use a Process Model
-Store an Object Reference to the New Execution in: e.g. Locals.ExecutionRef
After your Init steps you insert a ActvieX/COM Action Step that terminates the new execution:
-Object Reference: Locals.ExecutionRef
-Automation Server: NI TestStand API 3.1
-Object Class: Execution
-Call Method or Access Property: Call Method
-Method: Terminate
This will terminate your new execution showing the message popup.

Is there a way to center the text on a message popup

Looking for a way to center multiple lines of text on a Message Popup.

sdrochek3 -
The step type does not export any option to center text that it displays. If centering text is a requirement, you will need to create a custom dialog in your ADE of choice and display that instead.
Scott Richardson
National Instruments

HT204204 i tried to update to ios 8.2 on my iphone 5s when message popup to me now my iphone not working, please help i dont want to lose my data

hi
i tried to update to ios 8.2 on my iphone 5s when message popup to me now my iphone not working, please help i dont want to lose my data

What is the exact text of the message you got? And did you not back up before you updated?

Error in Local Message System: Error when opening an RFC connection Message

Hi Gurus,
We are not able to create support messages in our ECC production system but it can created in Development and Quality. Support message created appears in solution manager system. ECC System displays error message as
Error in Local Message System: Error when opening
an RFC connection Message was Not Created
I have checked RFC connection between ECC and Solution Manager which displays following message
Logon     Connection Error
Error Details     Error when opening an RFC connection
Error Details     ERROR: partner "local:sapgw00' not reached
Error Details     LOCATION: SAP-Gateway on host local / sapgw05
Error Details     DETAIL: NiPConnect2
Error Details     CALL: connect
Error Details     COMPONENT: NI (network interface)
Error Details     COUNTER: 40142
Error Details     ERROR NUMBER: 10060
Error Details     ERROR TEXT: WSAETIMEDOUT: Connection timed out
Error Details     MODULE: nixxi.cpp
Error Details     LINE: 2835
Error Details     RETURN CODE: -10
Error Details     SUBRC: 0
Error Details     RELEASE: 701
Error Details     TIME: Wed Jan 11 23:26:54 2012
Error Details     VERSION: 38
Kindly Help.....

Hi
Based on the instance number of the servers, you can determine the gateway to be used.
IF your ECC instance number is , 01 then gateway would be , sapgw01 (in ECC system)
So check and change the settings accordingly, in the RFC connection. Also check, if this entry sapgw01 is made in /etc/service file. Also check, in transaction smgw for gateway parameters.
Hope this info helps,
~ Raj

Adding a variable in a Message Popup

Hi guys, how to get a local variable in a message Popup? I try "string text"+ Runstate.Caller.Locals.foo ... Coz runstate is while program is running, Caller is the calling step and then local variable.
But this give an error. Where to access my local variables while running?

First of all, it depends on the data type of the variable. String can be added "similar" to the way you described. Numeric and boolean has to be cast.
Second, you seem to misunderstand the concept of the RunState-property. If you want to insert a local variable of the sequence you are currently running, the expression should be:
"My Dialog Text " + Locals.<localname>
Don't forget type casts if not working with string variables!
hope this helps,
Norbert
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it.

Message popup not appearing

I created a dll that had a message popup (userint.h) using Cvi version 6 on Windows XP, then using the Cvi runtime module and everything was good. I am now using Windows 7 (32 bit) and the latest Cvi runtime module and the dll partly works, does not give any errors, but the message popup does not appear.
My guess is the new Cvi runtime module maybe does not support the older message popup, but really dont know, could be the Windows version; anyone know about this?

Hi,
I don't believe MessagePopup has changed since CVI 3.0 as stated here: http://zone.ni.com/reference/en-XX/help/370051V-01/cvi/uiref/cvimessagepopup/
I would recommend stripping it down to the barebones and see if you can get it functioning that way.

Connection Message Archiver problems

Hoping someone can help.
I'm attempting to capture voicemail messages from multiple users. I need to preserve message headers and voicemail messages.
I've downloaded and installed the Unity Connection Message Archiver program from http://www.ciscounitytools.com/Applications/CxN/MessageArchiver/MessageArchiver.html
I followed all the step for configuration.
I can login and search for and select a mailbox or messages for archiving.
However, when I click the "Archive", I see the processing message, but then it reports an error.
Here is the error from the log file: "Failed establishing IMAP connection in the ConnectionMessageBackupFunctions constructor:Failed to attach to Connection server on port 7993 for IMAP login in AttachViaImap"
I've attached the full log file.
I've verified that the IMAP service is running. I've also followed all troubshooting steps found here: http://www.ciscounitytools.com/Applications/CxN/MessageArchiver/Help/MessageArchiver.htm
Can anyone point me in the right direction.
Thanks in advance.

Hi Jonathan,
I would move this thread over to the Unified Communications
Applications sub-forum as tool designer/engineer and Unity Connection
guru Lindborg will most likely have a great answer for you
https://supportforums.cisco.com/community/netpro/collaboration-voice-video/unified-comm-application?view=discussions
Cheers!
Rob
"May your heart always be joyful
And may your song always be sung
May you stay forever young "
- Dylan

Control Buttons in message popup with Digital I/O

In my Test system the   operator can use only the Start Stop Quit buttons on the Panel.
He aint have any mouse
That means I have to provide him wit all the control power thr' these 3 digital I/Ps
There are many message popups in the SequentialModel.seq file
The OPERATOR will respond to them with the 3 H/W buttons.
OK= Green
Terminate = Red
how can I assign my Buttons to all Popup messages on teststand Irrespective of their .(i.e handling them Individually)

My plan is to control the whole testsystem, with Hardware buttons (On off S/Ws for Operator) (operator wont be using mouse- it takes timeto scroll & prod is slow).
The H/W buttons r read thr   Labview. The file is a member function of the class that I call In teststand seq.
I am trying to  read and respond to Teststand dialogues thr' the Operator Interface using these 3   buttons

Excel 2007 Not allowing message popup when double clicking

Hello,
We have recently upgraded to Office 2007 and are using IP workbooks. When a user gets the "messages available; double click to display" the message box is not popping up. Does anyone know how to fix this issue? Not sure if it is an excel issue or a BEx issue.
Thanks,
Cherie

SAP Note 1299828 mentions that it has been fixed with BI Addon Support Package 9.
SAP Note 1294382 - SAPBINews NW7.0 BI Add-On Frontend SP900 - GUI 7.10 says:
Fixed in Bex Analyzer: "Message popup is not shown on double click in Excel 2007. Please read note 1299828."
I have it installed now but it does NOT work either (for me)!
At least in the global settings the option automatically popup messages works. Each action brings up the messages then.
Cheers,
Lars

Message popup timeout - time left

Can we get from the sequence context the time left (or time elapsed) of a timeout enabled message popup.
For example,
If the message popup is set to timeout after 120 sec and the operator responded when there are 50sec left for the step to timeout,
does any built-in variable have the value 50 (seconds left) or 70 (seconds elapsed)?
I know there are workarounds like calling Seconds() function in pre- and post-expressions and taking the difference but I wonder if it is already implemented or not.
Thanks.
S. Eren BALCI
www.aselsan.com.tr

This information is not stored in the step properties. It is possible to change the step type to get this information. The source code for MessagePopup is included with TestStand at <TestStand>/Components/NI/StepTypes/MsgBox/ if you have Labwindows/CVI.
Your suggestion of using Seconds() is much easier to implement and be accurate enough for your use cases.
Allen P.
NI

Connection Message Popup

Similar Messages

Maybe you are looking for