Connection PLAR on FXS port 2821

I have an anlog phone that is located by the main gate.  The phone has been extended and terminated into an FXS port on a 2821 router.  I am trying to configure a connect PLAR on he FXS port, so that when the phone goes off-hook it dials an internal VoIP extension.
I am not having any luck.  Any help would be appreciated.  My config is below:
voice-port 1/0/5
timing hookflash-in 50 0
connection plar 220005
description North gate
caller-id enable
dial-peer voice 220005 pots
destination-pattern 220005
port 1/0/5
dial-peer voice 100 voip
preference 1
destination-pattern 220...
modem passthrough nse codec g711ulaw
session target dns:CallAgent01
voice-class codec 1
voice-class h323 1
dtmf-relay h245-alphanumeric
no vad
Thanks!!
Jaime

Yosh - do I need to remove dial-peer voice 220005 pots for the PLAR to work correctly?
Thanks,
Jaime

Similar Messages

  • Connection Plar on FXS

    Hi all,
    I have the folowing situation:
    I have configure a 2821 mgcp gateway on CM 5.1.2 with EVM-8FXS/DID. On the fxs I only have configure a CSS and the prefix field. Afther i pick up the fxs phone the CM dials the prefix number and the is made sucessufly. If for same reason the called number disconect the call and the calling phone stays off-hook the fxs phone keeps calling the prefix dn every 3 seconds. Is there any way for the callmanager not do dial the prefix dn from the hot line if the hot-line stays off-hook.
    Thanks

    That is how its designed. Unless the fxs port goes on hook it will keep placing the calls. There is a feature in the VG248 that says
    Port busy signaling invoked softkey event
    which stops the vg to place a call unless a softkey event end call is received.

  • CFwd on FXS-Ports (mgcp)

    hi!
    How can I forward the Calls on an Phone witch is connected to an FXS-Port (mgcp, vg200)?
    How can I use the other Features, like PickUp etc.
    vy Markus

    Since there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
    If anyone else in the forum has some advice, please reply to this thread.
    Thank you for posting.

  • FXS Ports & Pickup Groups

    Is there a way to make an analog phone connected to an FXS port a part of a call pickup group that contains both analog phones & IP phones? I setup a lab and used MGCP to add the gateway and I was able to add the DN associated with the FXS port to a call pickup group. However, I am unable to figure out how to answer the call from the analog phone when another IP phone in the call pickup group is ringing.
    Thanks in advance

    Hi
    You are going down the right track with this.
    http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dde5372/0#selected_message
    See this other post I made (for a different purpose, but the principal is the same - it just opens up features available to IP phones for FXS ports by registering them using SCCP).
    Regards
    Aaron
    Please rate helpful posts...

  • EFTPOS No Response X0 Using FXS Port

    Hi All,
    Trying to get an EFTPOS machine working connected into an FXS Port using SCCP/STCAPP Protocol for call control.
    The port is registered in CUCM, I can connect an analogue phone to the port and successfully call the Bank's 1800 Number etc, I can make other external calls no problem.
    When I try the EFTPOS Machine, the call setup runs through normally and I see the call is then in a connected state. Approx about 10 or seconds later the call is cleared by the local device with an 0x8090 code Normal Clearing. The call is then disconnected and released as per any other call.
    The EFTPOS Machine prints a error for "Declined No Response X0"
    I have attached the following debugs.
    debug isdn q931
    debug voip vtsp all
    debug vop ccapi inout
    debug voip rtp session named-event
    Calling Number is 0245604627
    Called Number is 1800509183
    General environment setup is as follows.
    EFTPOS connect to FXS Port -> Registered to CUCM (9.1.2) -> SIP Trunk -> IOS 15.x -> ISDN Pri.
    Any feedback i smuch appreciated.
    Ben

    Not so sure if the service code being utilize by the FXS is the same as what is mentioned in VSA.Then again, the manual says "dial the corresponding * code on the client station" and if you look at an SPA9xx phone, it has the following codes defined for call park and call unpark code.
    *38
    *39

  • Transmission Volume on a FXS Port

    G'Day,
    We have a fax machine connected to an FXS port in a 2851 (CME 4.1). Running tests on the machine reveal that the transmission volume is set too high, causing distortion on faxes and an inability to fax to some destinations.
    Is there a way to turn the transmission volume down at the port-level? Apparently it cannot be done on the fax machine (? this sounds odd to me...but the technician for the machine is adament)
    Thanks,
    -marti-

    This depends if the faxing is being done via fax relay or fax passthrough.
    If fax relay is being used, the fax traffic originates from the egress voice port connected to the PSTN, not from the FXS port that has the fax machine on it. The output level of the fax relay codec is fixed - at this stage it is not possible to alter the level of the outgoing audio on the 2800/3800 ISR's.
    If you use fax passthrough, the audio is transmitted via a G711 codec. You can use the voice port 'input-gain' or 'output-attenuation' command to boost or reduce the levels in different directions.
    If the level FROM the CME system towards the PSTN is too high (for example 3dB), you would use the command 'input-gain -3' on the FXS port to reduce the inwards audio level by 3dB, so the level SENT to the PSTN is correspondingly reduced by 3dB.
    Most fax machines can set the outgoing audio levels - they may have a special config menu that is not normally directly accessible by users.

  • Connection plar on voice T-1 channels?

    Hi,
    can you do connection plar on t-1 voice channels.
    we have a scenerio where we need to be able to pass calls from unique T-1 voice channels to unique extensions in a remote site.
    thanks in advance

    thanks, that makes sense!
    so it should look something like this?
    Controller t1 1/0
    ds0-group 0 timeslots 1 type fxo-loopstart
    ds0-group 1 timeslots 2 type fxo-loopstart
    ds0-group 2 timeslots 3 type fxo-loopstart
    ds0-group 23 timeslots 24 type fxo-loopstart
    voice-port 1/0:0
    connection plar 100
    voice-port 1/0:1
    connection plar 101
    dial-peer voice 100 pots
    destination-pattern 100
    port 1/0:0
    dial-peer voice 101 pots
    destination-pattern 101
    port 1/0:1
    Thanks

  • Valcom 2001A single zone paging system with a Cisco 2821 FXS port

    I am new at troubleshooting the Valcom paging system with Cisco 2821 router.  I recently installed a Valcom 2001A that is connecting to FXS port on the Cisco router.  The paging works but the ringing does not stop when the page extension is dialed (you can talk over the ringing).  I was told to use the Valcom 9970 to work with the FXS port on my router.  Will the V9970 worth with the 2001A or in place of it?  Is there anything else I need to know to perfect this install?  Thank you! 

    Put the command 'forward-digits extra ,,,,01' on the outgoing POTS dial-peer. Each comma is one second of delay.

  • Advice about FXS Port configuration for connecting to modems

    Hello all,
    We have not confirm the problem, but we are having reports that analog devices like USR V.92 Modems and Power meters are not connecting or dropping the connection.  We have an ISR 2911 with the 4-port FXS-DID WIC (VIC3-4FXS/DID), configure to an internet SIP truck provider.  The Router is running IOS 15.3(3)M2.  If we connect an analog phone to the FXS port and call, voice is clear.  So the question is what configuration settings should we have for FXS ports and/or dialpeers for connections to modems?  Attached is the current configuration of the router.  
    Do we have to be worried about Codec?  If so which Codec should we configure?
    Any Physical FXS settings should be set?
    Are my DSP setup correctly?  
    Again, I'm at a loss, as voice sounds good and my searches for modem connections to FXS Ports on CUCME is coming up dry.  Any help would be great.  
    As far as the "Power Meters", we are talking substation power meters.  
    Thanks for any advice you can spare and your time,
    Nick

    Hi Amit,
    No problem on the delay.  Your help is very much appreciated.  
    You're losing me a bit.  Because I don't know if your giving me dial-peer 1 as an example.  1 being just a random number.  Or your telling me to change my current dial-peer 1 configuration.  Which is currently a pots dial-peer:
    dial-peer voice 1 pots
    description POTS port 0/1/0
    destination-pattern 111111111
    port 0/1/0
    dial-peer 1000 voip is our outbound call leg.  Sorry call legs are not exactly clear to me yet.  In fact they haven't been in years.  :)  So change my dial-peer to dial-peer voice 1 voip?  
    My other question still unknown to me is should we use:
    fax protocol pass-through g711ulaw
    Even though we are trying to use a modem and not a fax?  Also this command is a dial-peer command and not a global command.  So what global command should i be using?
    Again thank you for your time and help,
    Nick

  • Restricting FXS ports to internal calls only

    Hi,
    I have recently intalled Call Manager 8.5.1 with a H323 Gateway. On the gateway, I have a number of FXS ports for lobby phones. Is there a way I can restrict these phones to allow only internal calls only? Do I need to use COR lists like in Call Manager express or is there a  more practical way?
    Thanks,
    Derek

    Hi Derek,
    It sounds like these FXS ports are NOT registered to CUCM 8.5.1?  If they aren't, then yes COR lists is the most pratical way to do this.  You could do a "connection plar xxxx" to a receptionist extension and her her/him forward the calls to the correct extension.

  • SPA2102 FXS port state monitoring

    Hi all,
    Is there any way to get FXS port state for LinkSys SPA2102 VoIP adapter (i.e. is there a phone that connected to it or not) remotely, for example, via SNMP ?
    Thanks.

    Here's the bug ID: CSCse15025
    Doubt the NM is faulty - we had the same issue in a 2821 and migrated to 12.4(4)T4 to correct it. No hardware replacement required. All has worked fine since then.
    HTH
    Tom

  • Connection PLAR on WS-X6624 module

    How do you do this on the FXS port. Similiar method on IOS is connection PLAR at the voice-port. How do you do it with CAT OS?

    Hi -
    There is no PLAR specific config as far as the CatOS is concerned (assuming your 6624 is properly registered with CM).
    Here is how you do it with CM:
    1) Create a new partition for the PLAR (i.e. Loading Dock PLAR PRT)
    2)Create a new search space for the PLAR (i.e. Loading Dock PLAR SS)
    3)Add only the PLAR PRT to the new search space
    4)Create a translation pattern using NO digits in the translation pattern field. Put it in the PLAR PRT and give it the appropriate search space. In the called party transformation mask field put in the phone number you want the PLAR to ring to.
    5)Create an extension on the 6624 that has uses the new PLAR search space
    6)done!
    -Jaret

  • CLID not shown on FXS port

    I am using Call-manager 6.0.1b, a MGCP controlled Gateway.On the Gateway i have installed a NM-HD-2V with a Vic2-2FXS module. On this module i connect 2 analog phone with capability to display the Caller-ID. When i call the analog port from a ip phone or from the other analog phone the Dn is not shown. When i connect the phone directly to the PSTN and dial this nr via my cell phone the nr is shown so i expect that the nr format received is not correct. How can this performed that the correct format is shown to the FXS port connected phone ?

    Hi,
    Yes - you are correct. Looked at this one too quickly.
    You will want to make sure the CPTONE defined on the port is for the country the phone is manufactured for, and that the voice-pport has the 'caller-id enable' command.
    If those are both correct, and I'm guessing that they are since some caller-id works, then you need to inspect the gateways that take the calls to begin with.
    Do you have caller-id trouble for internal calls also?
    How do these calls come into your network?
    hth,
    nick

  • MGCP FXS ports requires a license in CUCM9

    Hello!
    I am connecting Some analoge phones to VG350 FXS ports which is  configured as a MGCP Gateway in CUCM. I beleive MGCP did not requires any license for it. Can some confirm this ? is there any Cisco doc on it ?
    Thanks & Regards,

    Hi Sambit,
    Technically u are correct but legally I think u would be requiring license.
    even the ordering guide says Analog devices are supported with Essential USer license  and must be purchased through UCL.
    http://www.cisco.com/web/partners/downloads/partner/WWChannels/technology/ipc/downloads/finalcopy.pdf
    regds,
    aman

  • How to configure FXO and FXS port?

    hi,
    can anyone help me on how to configure FXO port on 2820 router and FXS port on 2810.
    What are the things i need to configure to make a voip network that connect to PSTN network and PBX?

    hi
    do refer this link which can provide you fair idea to get started with your configs.
    http://www.cisco.com/en/US/partner/tech/tk1077/tech_configuration_examples_list.html
    regds

Maybe you are looking for