Connection problems with PALM TX and WRT160N router

I purchased a WRT160N wireless router. My computers connected with no problems, but when I attempted to connect my Palm TX I ran into a bunch of problems. At first the Palm would not even find the network. I eventually was able to configure the router so that the Palm can now find the network, but it still will not connect. I have removed the security from the network and rebooted both with no luck. I read that I am supposed to set the type to b/g mixed, frequency to 40 mghz, the wide channel to 6 and the other channel to 8. I was able to set the b/g mixed, the frequency to 20, the wide channel defaults to 3 (I cannot change this) and the other channel to 8. Any ideas?

Changing Router to b/g Mixed fixed the problem.
I had the same trouble. I've been trying to connect my Palm TX to my brand new Linksys WRT160N for a day and a half. Tried EVERYTHING....SSID Broadcast on/off, WEP, WPA, Security all off, nothing helped. I just switched the router settings to B/G Mixed. The TX connected immediately.
B/G will be fine, even though the router's optimum performance is N. My broadband operates at 25Mbs. 802.11g has a transfer rate of up to 54Mbs where N is well over 100. "G" will easily keep up with my internet's best speed. And I can still Wi-Fi with my TX at 802.11b (11Mbs).
I can temporarily switch to "N" if I ever want to transfer huge amounts of data between my "N" Laptop and my Desktop PC.
Message Edited by mgordonb on 12-16-2008 06:25 PM

Similar Messages

Is there a fix for the connectivity problems with iPhone 5S and ISO 7.0.2?

Is there a fix for the bluetooth connectivity problems with iPhone 5S and ISO 7.0.4?
I am having problems connecting the BT Audio and the handsfree phone connectyion is unreliable in 2012 Mitsubishi Lancer XL.
All worked OK with ISO 6.

Hello CraigNicholson
You would need to sync with iTunes to get that process to work for you. Check out the article below for more information on how to resolve that issue to get the proper token to use Push Notifications again.
iPad and iPod touch: Unable to use YouTube or Push notifications
http://support.apple.com/kb/ts3305
Regards,
-Norm G.

Why won't Apple fix the wifi connectivity problem with the iMac and new OS instead of just havin us go through hours of useless mock fixes!

I have spent hours with apple care about this problem with wifi connectivity. According to all the posts I'm not alone. I love my new IMAC
but i'll be glad to go back to my PC just so I can get my email without all the headaches. It seems that Apple has lost interest in
the IMAC and all of the problems associated with the new OS.

Keep in mind that ASC is where people go to get help, so yes, you are seeing reports of people who are having WiFi connection issues. But while it might seem like there are lots of people having trouble, given the sheer number of iMacs in use, it is a very small number. Also keep in mind that WiFi isn't totally under Apple's control. There are dozens of WiFi routers. Even worse, the manufacturers of WiFi routers often release firmware upgrades to fix flaws without ever informing the consumer. And just to add to the confusion, while WiFi 801.2 n routers have been sold for several years, for most of that time there was no agreed upon standard!
So if you'd like help, first, what router do you have and have you checked the vendor site to see that it has the latest firmware?

Connect problem with db link and scheduler_jobs on 10.2.0.4.0

hello guys
i have got this problem, i hope someone can help me to understand and solve it.
I have a pl/sql procedure where is referenced a table on a db_link. I own all the grants needed, and if i recall it in an anonymous block, it seems to work.
i.e
create or replace procedure routine_1 is
v_app varchar2(1);
begin
select 'x'
into v_app
from other_user.some_table@my_db_link
where rownum<2;
end routine_1;
Instead, while recalling it from a job scheduled with dba_scheduler package, with the same user, while opening the cursor where the db link table is referenced, i got a connect error:
ORA-01017: invalid username/password; logon denied
ORA-02063: preceding line from xxxxxx (where xxxxxx is the db link)
i would like to understand where i am mistaking. I already checked the user for the connection in the scheduled job and is the same of the anonymous block call.
thanks in advance
Claudio

hello dracis
thanks for the new answer.
i have not access to metalink. Anyway, oracle version is 10g not 11.
Anyway, about dbms_job package (Scheduler is the newer version of dbms_job), i found a phrase on a site saying this:
"Jobs that reference database links will fail if the database link is not fully qualified with the username and password. This is another subtle consequence of the execution environment of jobs."
Probably the cause is that the db link, to work, must be owned by the same user that owns the procedure where is referenced. In this way we hope ownername and password are in some way accessible.
We are trying to check this solution, but we have to wait for some grants.
Claudio

Sync problem with Palm IIIxe and outlook

I am unable to sync my PalmIIIxe with Outlook 2007 on my PC running MS Vista Home premium 32 bit. The Palm IIIxe is using Palm OS 4.1 with Hotsync 4.0. I have installed palm outlook 2007 conduits.
I do not get any options to either set up or configure conduits from the desktop Hotsync manger 7.0.2. When I first installed Palm Desktop by Access version 6.2.2 it asked if I wanted to sync with Palm desktop or Outlook, I chose outlook…..but it will not sync, although I have been able to load apps.
Any ideas?

Hi there,
I would recommend reviewing the process for syncing Outlook with iTunes. Take a look at the article below for more information.
iOS: Syncing your data with iTunes
http://support.apple.com/kb/HT1386
If you experience issues during that process then you may want to take a look at some of the troubleshooting steps found in the article below.
iPhone, iPad, iPod touch: Troubleshooting contact and calendar syncing via USB on Windows
http://support.apple.com/kb/HT1692
-Griff W.

Time Capsule Connectivity Problem with Airport Utility and Mavericks

I have a Time Capsule from 2011 which worked perfectly with my IMac and Airport Utility 5.6.1 but since the upgrade to Mavericks, I cannot get it to work with Airport Utility. Any help much appreciated. Thanks.

When you say.....
I cannot get it to work with AirPort Utility....
What does not work? Can you open up AirPort Utility and take us through the steps? What happens after each step?

Problem with Dell Printer and Wireless Router

I have a new Linksys Wireless Router (3100) and it handles 3 laptops, PS3 fine. But I have a Dell 715w network printer (also new). I have it set up on the network, and it works fine upon setup. The problem is the printer does not work all the time. Sometimes I can get an error message, sometimes it says it is busy, and other times it literally takes a long time to load and then does not print. I usually can get it to work again by rebooting and turning off the router and printer and laptops, but this hit or miss is very annoying and I never know when it will do this again, usually after a week or two. I wonder if the problem is that the 3 laptops all have different OS - XP, Vista and Windows 7. Dell tech support won't help as they say they don't support routers, but I am wondering whether the problem is ina s etting or if this printer is malfunctioning. any help would be appreciated

Yes. You have to key-in the IP address to the printer.
Basically, if the printer is set to obtain IP address from the router, it will be provided with a random IP or any IP available for the next device that will connect, on this issue, your printer. So there's no permanent IP address for the printer, making it a little hard to find at times. Compare it with the a static IP, your computer can easily map it since it doesn't change.

Connection problems with FCE HD and a Canon XL1

I just can not get the system to see the camera so I can capture. I have an external Firewire drive as my scratch disc. Any advice? Thanks!

Ian & Tom, First of all thanks for your ideas and quick replies, I really appreciate it.
I'm using a (Belkin) FW hub but have re-routed things so the camera is going directly to one of the computer's two FW ports. Have tried all suggestions provided in your posts but the best I'm able to get is a message that reads, "Unable to initialize video deck. You may still use Capture Now." When I go to capture mode, however, no controls are usable and it says, "not communicating."
Tom, I went to System Profiler and am not seeing the Canon. My computer has two FW ports and I'm only seeing the hub (and not the camera plugged into the other port). What's strange is that the hub is showing an "unknown device" but there's not an unaccounted for device plugged into the hub. I've tried the camera in both of the computer's FW ports to no avail. I'm guessing that's the weak link.
Regarding full system info...
- PowerMac G4, dual 1.27 GHz PowerPC
- OS X 10.4.10
- FCE HD 3.5.1
- EZ Quest external FW drive
- Canon XL1 (but my material was shot with a Panasonic DVX 100A, I'm just using the older Canon to capture for editing to save wear on the Panasonic's playback deck -- but the Panasonic connects just fine)
Any other info needed? You guys totally rock for trying to help me with this -- good karma!

Connection problems with ESA C160 and WSA S160

currently I have deployed ESA C160 and WSA S160 devices in a network but I cannot remotely connect to the devices.
I have installed Cisco 2811 Terminal server with octal cable connections and cannot seem to get terminal access.
As well I have connected the Management Interface to a local switch and provisioned VLANs on subnet 192.168.42.X to allow for access but no connection seems to work to gain access to the devices.
I am wondering if there is a specific cable configuration or connection which will allow me access to the applicances for configuration.
Any help is appreciated!

HI
Are you attempting a remote connection to the serial ports via 2811? I may be missunderstanding your post.
The serial ports are 9600 Baud 8N1. Typically you will use a null modem cable for the connection.
For the network you should be able to connect to the manamgement interface SSH and HTTPS should be enabled by default. If you connect directly to this port using a crossover cable can you establish a connection?
If the network connection is failing I would first start with the serial port so you can verify that the configuration is as you expect it to be, meaning the IP address and services enabled. If everything checks out in the configuration. I would next test using a crossover cable on the same subnet. If that works then I would connect the appliance to a switch and test from there. The biggest questions that come up are can you route to the appliance over the network and can you resolve the host over the network.
Christopher C Smith
CSE
Cisco IronPort Customer Support

Connection problems with Magic Mouse and handoff

I did a clean install of 10.10.3 and since then the Magic Mouse has had problems connecting. First it wouldn't pair. After a few reboots and repeated attempts I was able to pair the mouse with the rMBP. After waking from sleep it now no longer connects. I select the mouse in the Bluetooth menu and connect. Connection appears on the screen, but the mouse doesn't respond. After a few moments I get Connection Lost on the screen.
In addition to the mouse problems I have completely lost any hand off capability to or from the iPhone to the rMBP or back. It's like the Bluetooth connection between the devices is not working or is too weak to function.
It would be very much appreciated if any one has any suggestions on the cause or to a solution.
Thanks.

Hey Tom,
NVRAM and PRAM are, while technically different, effectively the same. Newer systems utilize NVRAM to store the same information that was stored in PRAM on older Macs.
On older Mac computers, similar information was stored in Parameter RAM (PRAM). Resetting NVRAM on Intel-based Macs using the same key combination is like resetting PRAM.
How to Reset NVRAM on your Mac
https://support.apple.com/en-us/HT204063
Cheers,
Allen

Connectivity problem with WRT610N v1 due to routing table issue

Greetings!
I have a puzzling issue with my new WRT610N.It is currently used as an access point so it's IP address is not the default 192.168.1.1 and instead 192.168.1.253.
After a month of use, internet connectivity via wireless has stopped working. My wireless clients can connect to it via WPA2 but it cannot reach my gateway, i.e., I cannot ping 192.168.1.1 to get out to the internet.
After checking all its settings, I've found that it's routing table for the LAN & Wireless interface has a gateway of 0.0.0.0. Comparing this with an old WRT54G, the gateway should be the IP of the WRT610N, i.e., 192.168.1.253.
The obvious solution would be to delete the invalid routing table entry, but the router's web interface does not provide that capability. I've tried entering a manual route entry of Destination LAN IP = 192.168.1.0, Subnet Mask = 255.255.255.0, Gateway = 192.168.1.253, Interface = LAN & Wireless but the router rejects it as an invalid route.
The last attempt is applying the latest firmware but the gateway 0.0.0.0 issue still persists.
Thanks in advance for the comments and suggestions.

Since you have upgraded the firmware of your Router, Have you resetted your Router and re-configure all the settings on your Router back again. If not then Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Here are some wireless settings which you can set on your Router.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
-Here select manual configuration...Wireless Network mode should be mixed...
-Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Wide-40MHz and change the Wide channel to 9 and Standard Channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on save settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2307 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Connection problems with idea pad and public network

My Lenovo Idea Pad connects fine at home on our ATT internet connectoin, but will not connect to a local public network at a local departent store. Anyone having suggestions email me at xxxxxxxxxxxxxx Thank you!\
Richard
Moderator note; e-mail address removed to stop the spambots getting it

I just saw your post and I resolved this on mine for my wired connection. I'm willing to bet that the issue is the same for wireless. Here's what I found.
Issue:
During the installation, iTunes installs some network components related to mobile device support over ethernet(Apple Mobile Device Ethernet Service - netaapl.inf). At the same time, according the logs, the install process removed OEM18.inf. This almost exactly coincided with the time that I saw the network connection die (preceded it by a few seconds).
Basically, iTunes appears to be removing a required network component.
Resolution:
After installing iTunes and the network connection breaking, remove the network device from Device Manager and allow Windows to reinstall it automatically.
The following instructions are for Windows 7, but they are close enough to follow for other versions of Windows.
1. Click the Start button (Jewel in Vista and Win7).
2. Right-click Computer and click Manage in the menu that appears (type your password or click Yes if prompted).
3. On the left side of hte Computer Management window, click Device Manager.
4. Click the arrow (or plus sign) next to Network Adapters to expand that section.
5. Right-click your network adapter and click Uninstall in the menu that appears.
6. Click OK.
7. Reboot.
Windows should automatically detect and reinstall your network device on boot.

Connectivity Problem with WPF Viewer and Oracle based imbedded reports

I've been using code to modify the Database, Username and Password in imbedded reports for quite a few years. Whether I was using C++ V6 or C# in VS2008, the process has been basically the same. Now I am trying to use the WPF Viewer in VS2010 and am getting an "ORA-00942: table or view does not exist" error. I perform a successful Connectivity Test and receive the error when I'm trying to view the report.
If I comment out all of the code that sets the source of the data and performs the connectivity test, the report shows up in the viewer and I'm presented a logon window similar to what I see when i design the RPT file in Crystal Reports. i.e the "Server Name:" shows the name of the Oracle Database I used when I designed the report; the "Database: " is empty; the "Login ID:" displays an edit box and contains the User ID I used when designing the report; and the "Password: " displays an edit box in which I type the password. Once I click on the OK button, the report is displayed in the WPF viewer.
Here is the code starting after I have loaded the report into a ReportDocument:
if(report.IsLoaded)
CrystalDecisions.Shared.TableLogOnInfo crTableLogonInfo;
CrystalDecisions.CrystalReports.Engine.Tables crTables = report.Database.Tables;
foreach(CrystalDecisions.CrystalReports.Engine.Table crTable in crTables)
    crTableLogonInfo = crTable.LogOnInfo;
    crTableLogonInfo.ConnectionInfo.LogonProperties.Clear( );
    crTableLogonInfo.ConnectionInfo.Attributes.Collection.Clear( );
    crTableLogonInfo.ConnectionInfo.DatabaseName = null;
    crTableLogonInfo.ConnectionInfo.ServerName = MyDatabase;
    crTableLogonInfo.ConnectionInfo.UserID = MyUsername;
    crTableLogonInfo.ConnectionInfo.Password = MyPassword;
    crTable.ApplyLogOnInfo(crTableLogonInfo);
report.SetParameterValue("StartingCPID", "AAAAAA");
report.SetParameterValue("EndingCPID", "ZZZZZZ");
if(report.Database.Tables[0].TestConnectivity())
    reportViewer.ViewerCore.ReportSource = report;
    reportViewer.ToggleSidePanel = SAPBusinessObjects.WPF.Viewer.Constants.SidePanelKind.None;
else
    MessageBox.Show("Unable to Connect to Database in report.");
Any idea what I'm doing wrong or what is different in this version?

See if the KB [
[1448013 - Connecting to Oracle database. Error; Failed to load database information|http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_bi/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333433343338333033313333%7D.do] helps.
Also the following may not hurt to have a look at (if only for ideas):
[1217021 - Err Msg: "Unable to connect invalid log on parameters" using Oracle in VS .NET|http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_bi/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333233313337333033323331%7D.do]
[1471508 - Logon error when connecting to Oracle database in a VS .NET application|http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_bi/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333433373331333533303338%7D.do]
[1196712 - Error: "Failed to load the oci.dll" in ASP.NET application against an Oracle database|http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_bi/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333133393336333733313332%7D.do]
Ludek
Follow us on Twitter http://twitter.com/SAPCRNetSup

Any wifi connection problems with new Macbook Pro 13" models?

I currently use a 15" Macbook Pro (about 3.5 years old) that has intermittent WiFi connection issues (intermittently loses signal). This seems to have been a very common problem with this laptop model. My kids, who use Macbooks, have no connection problems. In any case, I'd love to buy one of the new model 13-inch Macbook Pro's but hesitate because of my many issues with WiFi connectivity on my older Macbook Pro. Just wondering if anyone is experiencing connectivity problems with the new model?

I've never had Wifi connection problems with a Macbook and now with the 13" MacBook Pro I was flabergasted when I took my MacBook down the street to a coffee house with free WiFi. I went to connect to their WiFi and found my own WiFi connection listed. I thought this odd even though I was on the same block as my apartment, my apartment is six stories up. I connected to the Coffee Shop WiFi but it was really slow so I wondered if I could connect to my own home connection. I switched it over and lo-and behold I did connect! It was a good 300 feet away! I NEVER saw this with previously owned MacBooks including the black MacBook and the MacBook offered just before they moved the MacBook up to the Pro series.
So I'd say they have improved the WiFi nicely.

HT204409 I am trying to log onto my wireless connection but it keeps telling me I'm unable to locate any wireless network. I know there are several networks nearby. Is this a problem with my phone or my router?

I am trying to log onto my wireless connection but it keeps telling me I'm unable to locate any wireless network. I know there are several networks nearby. Is this a problem with my phone or my router?

I found a solution that has worked on both iPhone 4's I have that have had the same issues, and also including not being able to download updates in the App store.
Go to Settings > WiFi and turn it OFF.
Next go to General > Cellular > Cellular Data and turn it OFF
Next go back to Settings > WiFi and turn it ON, (wait a few seconds for it to sync with your network)
Finally go back to General > Cellular > Cellular Data and turn it ON.
I had the same issues on both my wife's phone, and my own, and it fixed it immediately without changing any proxy settings or reboots, (which I did try on my phone and did not work, but did not try on my wife's phone)
Hope this helps!

Connection problems with PALM TX and WRT160N router

Similar Messages

Maybe you are looking for