Connectivity error in Receiver com. channel

Hi Experts,
I have asynchronous scenario in PI 7.1 system, PI Receiver channel is trying to pass the data to the target system (non-SAP) in asynchronous manner.
I have observed that for few minutes lets say 1-2 or minute, connectivity related error is coming in RWB-channel monitoring and then again messages are started to get processes successfully by the same receiver channel, this happens randomly in a day.
the below is the audit log from RWB.
my query is:
is this the internal module processor error before transmitting the message to Target system or this error comes when module processor is trying to send the message to target system and connectivity with target system gets failed?
I have got this query because in error message it says (highlighted in above screenshot), "Message could not be forwarded permantely to
JCA Adapter" and "Adapter call failed"
please suggest for this uncertain behaviour of Receiver channel.
Regards,
Jagesh

Hi Jagesh,
I am thinking can it be the bad Network issue between the SAP PI and integrated target system?
This could be the reason, What adapter are you using?
I am not getting your point "The Timeout can be raised for the endsystem and not for PI" can you pls give some detail on this.
I wanted to mean that the endsystem can be overloaded. If the PI delivers a great amount of messages or larger ones, the end of the communication, by timeout, can be in the endsystem and not in PI because i noticed only 20 seconds in the timeout response. In order to know if PI is raising the timeout you should increase this PI value, depending the receiver adapter and your PI version you can do it in different ways.
Regards.

Similar Messages

Getting the following error in receiver RFC channel

Hi Folks,
Iam having two RFC channels one as SENDER and other as RECEIVER.Ensuring that all the required data is perfectly given while creating these two channels...the SENDER RFC channel status is green in channel monitoring and RECEIVER RFC channel is red!
Iam gettiing follwing error against RECEIVER RFC channel -
<b>"Receiver channel 'Receiver_RFC' for party '', service 'BXT_100_IS'
Error can not instantiate RfcPool caused by:
com.sap.aii.adapter.rfc.RfcAdapterException: error initializing RfcClientPool:com.sap.aii.adapter.rfc.core.repository.RfcRepositoryException: can not connect to destination system due to: com.sap.mw.jco.JCO$Exception: (103) RFC_ERROR_LOGON_FAILURE: Name or password is incorrect. Please re-enter"</b>
Even iam pretty sure about the user and pwd used in RECEIVER RFC channel...
and also i noticed "perform notification" status is failed in cache notification against my user id...
Can anyone help me in resolving this issue..
Thanks in advance..
Regards,
Ram.

Hi Ram,
Please change your password to UPPERCASE and try.
I have came across few instances where SAP converts passwords to uppercase while storing and so they dont match.
Hope this helps.
Regards,
Rahul.

Error in Receiver Communication Channel in FCC

I have a simple scenario of Proxy to File. I have to just one field in complete row. So my structure is as below : MT_RecordIB -> Records. So my XSD looks like this :
<xsd:schema xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns="http://XXXl.com/INF31018/SAPSerOrd_DaysIn" targetNamespace="http://hnwl.com/INF31018/SAPSerOrd_DaysIn">
   <xsd:element name="MT_RecordIB" type="DT_RecordIB" />
   <xsd:complexType name="DT_RecordIB">
      <xsd:sequence>
         <xsd:element name="Records" type="xsd:string" />
      </xsd:sequence>
   </xsd:complexType>
</xsd:schema>
I have used FCC and the parameters are :
Recordset Structure                                  Records
Records.fieldSeparator             'nl'
But I am getting following error in Receiver Communication Channel :
Failed to process message content. Reason: Exception in XML Parser (format problem?):'java.lang.Exception: Message processing failed in XML parser: 'Conversion configuration error: Unknown structure 'ns0:MT_RecordIB' found in document', probably configuration error in file adapter (XML parser error)' (Software version: 3.0.21)
Thanks,
Pankaj Singh

Hey Pankaj,
Your content conversion parameter might be configured improperly.
Refer this blogs
/people/shabarish.vijayakumar/blog/2007/08/03/file-adapter-receiver--are-we-really-sure-about-the-concepts
/people/arpit.seth/blog/2005/06/02/file-receiver-with-content-conversion
Refer the following threads for your problem
[ Unknown structure 'ns0:MT_dbglgtr_FileName' found in document'|Unknown structure 'ns0:MT_dbglgtr_FileName' found in document']
Rgds
Ramesh

Error in Receiver File Channel...in MTB module (Urgent)

Hi,
I am working on a Proxy to File scenario. I am using Message Transformation Bean in receiver file channel to convert xml file into fixed length file. I am getting an error : Transform: failed to execute the transformation: com.sap.aii.messaging.adapter.trans.TransformException: Error converting Message: java.lang.Exception: Exception in XML Parser (format problem?):java.lang.NullPointerException'; nested exception caused by: java.lang.Exception: Exception in XML Parser (format problem?):java.lang.NullPointerException
in MTB step of audit log for comm channel.
Please help me resolve this.
Thanks,
Jaya

Hi ,
"Transform: failed to execute the transformation:"
Pls check ur data what u have to send .. any missing information or any special Chacters or any extra fields are available in the data, this type of transformation error raised.
check once again ur mapping transformation and test the mapping in INTEGRATION REPOISTERY with the same data(what u have to send Previously).
and also check ur adapter status in RWB.
Regards,
Sateesh N.
Edited by: Sateesh N on Apr 21, 2008 1:53 PM

Error in receiver comm channel

Hi All,
   I am working on scenario file to file with out IR.just picking up the file from sap app server and placing in target ftp server.
My sender comm channel is picking the file fine but when in receiver comm channel i am getiing error as
"Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException: Unknown payload format 0 in message"
"Attempt to process file failed with Unknown payload format 0 in message"
i have checked in content of the file it contains no special character. are any security is being maintained.
please advise on this.
Thanks,
Bhaskar

Hi Jude,
I have checked in sender comm channel in message display tool under message content i am getting error as below.
messagecontent
message part [soap document]
500   Internal Server Error
SAP J2EE Engine/6.40
Application error occurred during request processing.
Details:   Error [javax.servlet.ServletException: null], with root cause [java.lang.NullPointerException: null].
Exception id: [00145E474044003F000018AD00003E0D000471A1CBF6A02A]
what would be the error and how can i find it.
Is this basis related issue?
Thanks,
Bhaskar

JDBC : error in receiver communication channel?

Hi Experts ,
I am doing a JDBC to JDBC scenario. The following error comes in my receiver communication channel monitoring.
Error while parsing or executing XML-SQL document: Error processing request in sax parser: Error when executing statement for table/stored proc. 'VIN_STG_STORER_RMS' (structure 'Statement'): java.sql.SQLException: FATAL ERROR document format in structure 'Statement': expected 'access' tag(s) not found
My receiver data type has got the 'access' tag. What other reason can cause this error?
Receiver table name : VIN_STG_STORER_RMS
Regards,
Shamly

Hi Ranjit,
My moni shows processed successfully. but the error is in communication channel.
I have pasted below the target xml structure. Any suggestions?
Thank you.
Shamly.
<?xml version="1.0" encoding="ISO-8859-1"?>
<xsd:schema xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns="http://mg.adityabirla.com/mg/wms/store_supps" targetNamespace="http://mg.adityabirla.com/mg/wms/store_supps">
<xsd:element name="MT_WMS_Store_Supps" type="DT_WMS_Store_Supps" />
<xsd:complexType name="DT_WMS_Store_Supps">
<xsd:annotation>
<xsd:appinfo source="http://sap.com/xi/TextID">
1f3cf480f98411dcb83a0003ba0adbbd
</xsd:appinfo>
</xsd:annotation>
<xsd:sequence>
<xsd:element name="Statement">
<xsd:annotation>
<xsd:appinfo source="http://sap.com/xi/TextID">
33dd8ee0ef5c11dcb812001d7df81104
</xsd:appinfo>
</xsd:annotation>
<xsd:complexType>
<xsd:sequence>
<xsd:element name="VIN_STG_STORER_RMS">
<xsd:annotation>
<xsd:appinfo source="http://sap.com/xi/TextID">
33dd8ee1ef5c11dca724001d7df81104
</xsd:appinfo>
</xsd:annotation>
<xsd:complexType>
<xsd:sequence>
<xsd:element name="access" minOccurs="0" maxOccurs="unbounded">
<xsd:annotation>
<xsd:appinfo source="http://sap.com/xi/TextID">
a31a45f0ef5c11dca305001d7df81104
</xsd:appinfo>
</xsd:annotation>
<xsd:complexType>
<xsd:sequence>
<xsd:element name="STORERKEY" minOccurs="0">
<xsd:annotation>
<xsd:appinfo source="http://sap.com/xi/TextID">
a31a45f1ef5c11dcb3c3001d7df81104
</xsd:appinfo>
</xsd:annotation>
<xsd:simpleType>
<xsd:restriction base="xsd:string">
<xsd:minLength value="0" />
<xsd:maxLength value="15" />
</xsd:restriction>
</xsd:simpleType>
</xsd:element>
<xsd:element name="TYPE" minOccurs="0">
<xsd:annotation>
<xsd:appinfo source="http://sap.com/xi/TextID">
a31a45f2ef5c11dcc33e001d7df81104
</xsd:appinfo>
</xsd:annotation>
<xsd:simpleType>
<xsd:restriction base="xsd:string">
<xsd:minLength value="0" />
<xsd:maxLength value="30" />
</xsd:restriction>
</xsd:simpleType>
</xsd:element>
<xsd:element name="WHSEID" minOccurs="0">
<xsd:annotation>
<xsd:appinfo source="http://sap.com/xi/TextID">
a31a45f3ef5c11dcabb7001d7df81104
</xsd:appinfo>
</xsd:annotation>
<xsd:simpleType>
<xsd:restriction base="xsd:string">
<xsd:minLength value="0" />
<xsd:maxLength value="30" />
</xsd:restriction>
</xsd:simpleType>
</xsd:element>
...and so on for many other fields.
Edited by: Shamly MM on Mar 24, 2008 10:27 AM

HTTP/1.1 400 Bad Request error in receiver REST channel

Hi Experts
I am currently working on an interface in which we have created a REST communication channel on the receiver side.
The below error comes up in the PI when we try to perform the GET operation on the URLs given below:
Error Message: HTTP error occurred: HTTP/1.1 400 Bad Request
URLs -
i) https://<myHost>:<myPort>/businesses/search?Keyword=Viridor&ResultsPerPage=10
ii) https://<myHost>:<myPort>/businesses/ec92a1e9-cef0-48aa-8800-a2e500ce8b1c/sites?Keyword=Viridor&ResultsPerPage=10
When we use SOAP UI to perform the above test, it works perfectly fine and fetches the required response from the target REST server.
Also, when we use the URL - https://<myHost>:<myPort>/businesses in the receiver communication channel in PI, it works fine and retrieves the
values of all the businesses present on the target server, however on making URL more specific - like the two URLs above, it does not work
and gives the bad request message.
Please can you let me know what could be the issue.
Thanks,
Maheswarareddy

Hi All,
Issue resolved:) ...that due to When calling a URL in the REST Receiver Channel, all GET variables are ignored
so we had to upgrade SP10 patch level 5 and all services are working as we expected.
Also pls check Note :2114322
Thanks,
Maheswarareddy

Why can't I use my apple id in imessage? Network connection error message always comes up!

I have iphone5 currently on the latest iOS 6.1.2. I am connected to wifi which is perfectly working. My iMessage is perfectly working using my mobile number but can't add my apple ID. When i try to add my apple ID to use for imessage, an error message always comes up: "Could not sign in. Please check your network connection and try again." How can I resolve this? any help would be greatly appreciated.

Read here:
http://support.apple.com/kb/TS4268

Error in receiver JDBC channel

Hi,
I have a receiver JDBC scenario, which must execute a stored procedure.
Output message seems correct:
<ns0:MT_SQL xmlns:ns0="http://www.xxxx">
<STATEMENT1>
   <DIRECC ACTION="EXECUTE">
       <TABLE>biz_mag_clientes_direcciones</TABLE>
       <idcliente type="VARCHAR">0001000692</idcliente>
       <idtipodir type="VARCHAR">1</idtipodir>
       <iddireccion type="VARCHAR">0210054466</iddireccion>
       <idtipovia type="INTEGER">1</idtipovia>
       <idciclovida type="VARCHAR" />
       <idmaestro type="VARCHAR" />
       <idtiporeplicacion type="VARCHAR" />
       <cp type="VARCHAR">08188</cp>
       <callenum type="VARCHAR">UR CAN SALA XIC APDO. CORREOS 507,</callenum>
       <telefono type="VARCHAR">9999999</telefono>
       <observacion type="VARCHAR" />
       <grupocnae type="VARCHAR">55</grupocnae>
       <subgrupocnae type="VARCHAR">5541</subgrupocnae>
</DIRECC>
</STATEMENT1>
</ns0:MT_SQL>
But there is an error in receiver CC:
Unable to execute statement for table or stored procedure. 'biz_mag_clientes_direcciones' due to java.lang.NumberFormatException: For input string: "1 "
I think this problem it's due to idtipovia field (INTEGER type), but i don't know how to solve it.
Any input, please ? Thanks
Carme.

Yuki, if i defined this field as CHAR, cc returned this error:
JDBC message processing failed; reason Error processing request in sax parser: Error when executing statement for table/stored proc. 'biz_mag_clientes_direcciones' ): com.microsoft.sqlserver.jdbc.SQLServerException: Error converting data type nvarchar to int.
Because this field is INTEGER type in target stored procedure .
Ravi, This field is defined as xsd:integer in data type.
Thanks,
Carme.

Space line is added if receiver com. channel only receive part of the msg

The structure of my inbound message is :
Message_A
      Fileld_1
      sub_structure
           Filed_2
           Field_3
In the receiver communication channel, I input 'sub-structure' in the field 'recordset structure' shown in the tab 'Content conversion parameters'
The message contents inside 'sub-structure' is supposed to be passed out and sent the destination defined in receiver communication channel. It work in my situation but a space line was added in the first row.
If I modify the struture as below. Then a space line was added at in the last row.
Message_A
      sub_structure
           Filed_2
           Field_3
      Fileld_1
I want to remove the space line. Pls. help

The structure of my inbound message is :
Message_A
1. Fileld_1
2. sub_structure
2.1. Filed_2
--- 2.2. Field_3
In the receiver communication channel, I input 'sub-structure' in the field 'recordset structure' shown in the tab 'Content conversion parameters'
The message contents inside 'sub-structure' is supposed to be passed out and sent the destination defined in receiver communication channel. It work in my situation but a space line was added in the first row.
If I modify the struture as below. Then a space line was added at in the last row.
Message_A
1. sub_structure
---1.1 Filed_2
---1.2 Field_3
2. Fileld_1
I want to remove the space line. Pls. help
Edited by: Pansy Leung on Jan 20, 2012 7:43 AM

SMTP Receiver Communication Channel error: connection refused

Dear all.
When migrating processes from XI 3.0 to PI 7.1 we run into the problem that we can't get the SMTP Receiver Communication Channel working on PI. We get the following error in Communication Channel Monitoring:
Message processing failed. Cause: com.sap.aii.af.sdk.xi.srt.BubbleException: Failed to call the endpoint [null "null"]; nested exception caused by: java.net.ConnectException: Connection refused: connect
(The NetWeaver Administrator log shows the following:
unable to call the mailer: com.sap.aii.af.sdk.xi.srt.BubbleException: Failed to call the endpoint [null "null"]; nested exception caused by: java.net.ConnectException: Connection refused: connect)
- We copied all configuration settings 1-on-1 from XI to PI, and double-checked we made no mistakes.
- We confirmed the PI system can in fact reach the mailserver by successfully sending Email from the ABAP stack of the PI system (transactions SOST and SCOT)
- When deliberately mistyping the mailserver URL, we get the error: java.net.UnknownHostException. This makes me believe that the 'connection refused' error we get (after re-entering the correct mailserver URL) is indeed coming from the mailserver. But why would it refuse the connection if it allows the connection from the ABAP stack of the same server? And why didn't we run into any such problems on XI?
Any help is much appreciated!
Kind regards,
Eddy Driessen.

Hi All,
We have upgraded our XI3.0 system to PI7.1 and currently performing testing for different adapters. We are also facing similar problem for a scenario File to Mail
19.11.2010 11:31:56     Error     Mail: error occured: java.net.UnknownHostException: [url]
19.11.2010 11:31:56     Error     Mail: error occured: com.sap.aii.af.lib.mp.module.ModuleException
19.11.2010 11:31:56     Error     Adapter Framework caught exception: Failed to call the endpoint
19.11.2010 11:31:56     Error     Delivering the message to the application using connection Mail_http://sap.com/xi/XI/System failed, due to:                     com.sap.engine.interfaces.messaging.api.exception.MessagingException: com.sap.aii.af.sdk.xi.srt.BubbleException: Failed to call the endpoint [null " null"];                     nested exception caused by: java.net.UnknownHostException: [url].
19.11.2010 11:31:56     Information     The message status was set to WAIT.
*[url] = Mail server
Can anyone suggest the steps to solve this error
Thanks
Varun

Error in the SOAP Receiver communication channel

Hi ,
My scenario is RFC - to -SOAP (synchronous ) i have specified the TARGET URL inthe SOAP receiver comminication chanel.. but while testing the interface by providing the test data from R/3 .. I'm not getting any Respose.. ..
If I check in the SXMB_MONI in i'm getting the following message .. but the URL whicjh i provided that is fine.. but my doubt is through XI may be it's not able to connect the Target System... .. so, please suggest me...
<SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
<SAP:Category>XIAdapterFramework</SAP:Category>
<SAP:Code area="MESSAGE">GENERAL</SAP:Code>
<SAP:P1 />
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText>com.sap.aii.af.ra.ms.api.DeliveryException: www.webservicex.net</SAP:AdditionalText>
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack />
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
regards
Jain

By default, the SOAP adapter sends the SOAP message with the content type text/xml.
When you check "Do not use SOAP envelope", the default contnet type is application/xml.
You can change the content type like this: Go to the SOAP receiver communication channel module tab. Add the module "localejbs/AF_Modules/MessageTransformBean" before the standard module. Add the parameter name Transform.ContentType and value text/xml.
Check out this
/people/varadharajan.krishnasamy/blog/2007/01/09/troubleshooting-soap-message--xi
One way of testing ur scenario
/people/michal.krawczyk2/blog/2005/08/25/xi-sending-a-message-without-the-use-of-an-adapter-not-possible
Also have a look here
SAP Note 856597
reward points if solution found helpfull
regards
chandrakanth

File Receiver Comm Channel in error

Hi All,
I am getting below error in my receiver communication channel -
Transmitting the message to endpoint <local> using connection File_http://sap.com/xi/XI/System failed, due to: com.sap.engine.interfaces.messaging.api.exception.MessagingException: Unable to clone File Adapter receiver channel for parallel processing
This is just FiletoFile scenario. I am trying to use VARIABLE SUBSTITUTION here to give dynamic name to the file at receiver. I haven't use FCC here.
If I dont use VARIABLE SUBSTITUTION then scenario is working fine.
Thanks & Regards,
Rashmi Joshi

Hi Abhradeep,
I am getting new error now -
Transmitting the message to endpoint <local> using connection File_http://sap.com/xi/XI/System failed, due to: com.sap.engine.interfaces.messaging.api.exception.MessagingException: com.sap.aii.adapter.file.configuration.DynamicConfigurationException: Error during variable substitution: com.sap.aii.adapter.file.varsubst.VariableDataSourceException: The following variable was not found in the message payload: Vname
I have changed the reference value as -
Emp_ID
payload:MT_File,1,Record,1,Emp_ID,1
Thanks & regards,
Rashmi Joshi

Receiver JMS Channel Error

hi,
I am facing an issue with the JMS Receiver Communication channel.Data is not getting inserted in the JMS Queue.CC Monitoring is showing the below ERROR:
Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException: Connector for ConnectionProfile of channel: JMS_r_CustomerLedgeron node: 7065651 having object id: 340fa47e4dc33a04a4f8a5a108708f07 encountered error: Error sending message in sending to destination custLedgerReplication, the message message: TextMessage[null, <?xml version="1.0" encoding="...]: weblogic.jms.common.JMSException: Error sending message.
can someone helpme out.
thanks,
robin

Hello Robin,
did you resolve this issue? I have now the same problem.
Do you have connections with two (or more) BEA servers using the same Adapter Framework?
Note 1090516 describes a problem with credentials confusion when connecting to more servers.
It could be the cause.
With regards
Tomas

Mac won't update software or access iTunes shop. Message comes up with 'not connected to the net. Check connections' error. I still have internet access. Changed my Apple ID but no result. Repaired permissions and re-installed operating system.

Mac won't update software or access iTunes shop. Message comes up with 'not connected to the net. Check connections' error. I still have internet access. Changed my Apple ID but no result. Repaired permissions and re-installed operating system.

It sounds like you may have multiple problems, but none of them are likely to be caused by malware.
First, the internet-related issues may be related to adware or a network compromise. I tend to lean more towards the latter, based on your description of the problem. See:
http://www.adwaremedic.com/kb/baddns.php
http://www.adwaremedic.com/kb/hackedrouter.php
If investigation shows that this is not a network-specific issue, then it's probably adware. See my Adware Removal Guide for help finding and removing it. Note that you mention AdBlock as if it should have prevented this, but it's important to understand that ad blockers do not protect you against adware in any way. Neither would any kind of anti-virus software, which often doesn't detect adware.
As for the other issues, it sounds like you've got some serious corruption. I would be inclined to say it sounds like a failing drive, except it sounds like you just got it replaced. How did you get all your files back after the new drive was installed?
(Fair disclosure: I may receive compensation from links to my sites, TheSafeMac.com and AdwareMedic.com, in the form of buttons allowing for donations. Donations are not required to use my site or software.)

Connectivity error in Receiver com. channel

Similar Messages

Maybe you are looking for