Console cluster reporting is not consistant with dynamic list

          (We are using the 6.1 sp2 plug-in for Linux. Our web server - apache - is on Solaris
          and our WL servers are on Linux Ret hat. 7.2 2.4.9-31smp)
          Recently our production site experienced the following unfortunate scenario:
          Here are the specifically the events that took place:
          On Sept 6 @ 2:30 pm:
               I observered that the Admin console was reporting that only 3 (servers #3, #5
          and #6) out of the 6 servers were participating in the cluster. On the other
          hand, From the access logs, I was still seeing activity on all 6 servers.
               At the same time, our operations team did not report any T3 PING failures (Tivoli
          automates the sending of T3 PING two each of the 6 servers in the cluster every
          10 minutes) which indicated that none of the server where in a hung state. This
          further verified that the all 6 servers were healthy.
               Question: Why was the plugin still distributing traffic to all 6 servers despite
          the fact (as reported by the admin server) that 3 of the 6 servers were no longer
          participating in the cluster? Shouldn't the dynamic list have excluded these
          3?
          On Sept 6 @ 11:30 pm: The operation team reported that all 6 servers where no
          longer responding to a ping (hung state). I then checked the admin console and
          it was reporting that none of the servers were participating in the cluster.
          Is there a bug with the 6.1 sp2 console?

Nael,
          This is a known problem. Please contact support and reference CR075667 to obtain the
          appropriate fix.
          Regards,
          Simon
          Developer Relations Engineer
          BEA Support
          Nael Ramadan wrote:
          > (We are using the 6.1 sp2 plug-in for Linux. Our web server - apache - is on Solaris
          > and our WL servers are on Linux Ret hat. 7.2 2.4.9-31smp)
          > Recently our production site experienced the following unfortunate scenario:
          >
          > Here are the specifically the events that took place:
          >
          > On Sept 6 @ 2:30 pm:
          >
          > I observered that the Admin console was reporting that only 3 (servers #3, #5
          > and #6) out of the 6 servers were participating in the cluster. On the other
          > hand, From the access logs, I was still seeing activity on all 6 servers.
          > At the same time, our operations team did not report any T3 PING failures (Tivoli
          > automates the sending of T3 PING two each of the 6 servers in the cluster every
          > 10 minutes) which indicated that none of the server where in a hung state. This
          > further verified that the all 6 servers were healthy.
          > Question: Why was the plugin still distributing traffic to all 6 servers despite
          > the fact (as reported by the admin server) that 3 of the 6 servers were no longer
          > participating in the cluster? Shouldn't the dynamic list have excluded these
          > 3?
          >
          > On Sept 6 @ 11:30 pm: The operation team reported that all 6 servers where no
          > longer responding to a ping (hung state). I then checked the admin console and
          > it was reporting that none of the servers were participating in the cluster.
          >
          > Is there a bug with the 6.1 sp2 console?

Similar Messages

Creating Report using EPM Functions with Dynamic Filters

Hi All,
I am new to BPC, In BPC 7.5 i seen like we can generate EPM report using EVDRE function very quickly and easy too. Is the same feature is existing in BPC 10.0 ? if no how can we create EPM reports using EPM Functions with Dynamic Filters on the Members of the dimension like in BPC 7.5.
And i searched in SDN, there is no suitable blogs or documents which are related to generation of Reports using EPM Functions. All are described just in simple syntax way. It is not going to be understand for the beginners.
Would you please specify in detail step by step.
Thanks in Advance.
Siva Nagaraju

Siva,
These functions are not used to create reports per se but rather assist in building reports. For ex, you want to make use of certain property to derive any of the dimension members in one of your axes, you will use EPMMemberProperty. Similary, if you want to override members in any axis, you will make use of EPMDimensionOverride.
Also, EvDRE is not replacement of EPM functions. Rather, you simply create reports using report editor (drag and drop) and then make use of EPM functions to build your report. Forget EvDRE for now.
You can protect your report to not allow users to have that Edit Report enabled for them.
As Vadim rightly pointed out, start building some reports and then ask specific questions.
Hope it clears your doubts.

After REFRESH the cached object is not consistent with the database table

After REFRESH, the cached object is not consistent with the database table. Why?
I created a JDBC connection with the Oracle database (HR schema) using JDeveloper(10.1.3) and then I created an offline database (HR schema)
in JDeveloper from the existing database tables (HR schema). Then I made some updates to the JOBS database table using SQL*Plus.
Then I returned to the JDeveloper tool and refreshed the HR connection. But I found no any changes made to the offline database table JOBS in
JDeveloper.
How to make the JDeveloper's offline tables to be synchronized with the underling database tables?

qkc,
Once you create an offline table, it's just a copy of a table definition as of the point in time you brought it in from the database. Refreshing the connection, as you describe it, just refreshes the database browser, and not any offline objects. If you want to syncrhnonize the offline table, right-click the offline table and choose "Generate or Reconcile Objects" to reconcile the object to the database. I just tried this in 10.1.3.3 (not the latest 10.1.3, I know), and it works properly.
John

Web Analysis report is not coming with the border/logo/heading while print

Hi All,
I am using 9.3.1 version of hyperion planning were Web Analysis report is not coming with the border/logo/heading while printing with the option "print all object", Only the data grid is coming in the print. If I use "print screen" it is coming with border/logo/heading but it gives a screenshot of the report, that won't cater out need.
So please suggest us with a resolution to have border, logo and heading, while using Print all object.
Thanks with regards....
Rao

Hi Sagar,
In scripts when you will see print preview the logo will be not shown up with clarity.Take the print out of the document and check whether logo is printing up with clarity.
Thanks
Phani

G/L Account currency is not consistent with G/L Interim Account currency

Hello
A few days ago I was printing checks and suddenly an error occurs
it says something like..."Another user is accessing the same account"
In the reserch I found help in SAP Portal, where I showed how to unlock this part
This I did in Administration->Set up-> Banking-> House Bank accounts
At the end is a column that says BLOCK PRINTING, always locked, but when the error occurs is enabled for the account that has been affected, and a super user must unlock by unchecking the check box.
The problem is that the update that part I get an error message and I have not been able to unlock
The error is
G/L Account currency is not consistent with G/L Interim Account currency [Message 60701-9]
In this regard I have not found anything to help me resolve this error and the printing of checks is blocked
I need your help
Regards.
Yen

Hi
i found the problem, we have an accunt that is just visible in House bank accunt window when try to select an account in the column G/L intermin account, but that account is not an active account , the descrpction says "Copy express transport account" i delete it in all the rowa and finaly we could update the window.
Regards
Yen

The creditors report is not matching with the G/L account

Hi Gurus,
The creditors report is not matching with the G/L account ,where i can go and find out the differences ?
Please give me advice,
I will assign points
Thanks&Regards,
Kumar

Hi Kumar,
There could be three reasons.
1. You may have more than one recon accounts for different vendor groups. So, you need to select all the GL accounts when reconcile with Vendor balances.
2. You may have some special GL transactions, which may post to different reconciliation accounts. Please check Special GL transactions (Down payments so on)
3. Your vendor recon accounts may be changed after some postings. Please check. If changed, you need to select these GLs also for reconciliation with vendor balances.
Hope this will help you. If not clear please reply, I will explain you.
Pl. assign points if useful.
Thanks

Balance of S_ALR_87012168 and S_ALR_87012167 is not consistent with FBL5N

Dear all,
Could you kindly let me what's the reason that cause S_ALR_87012168 and S_ALR_87012167 is not consistent with FBL5N.
When view line item anlaysis the line item is the same with FBL5N, but in the first page of due / not due anlysi, the result is not the same?
Thanks bnd Best Regards.
CSY.

Hello
first thing you should do it is to run the programm SAPF190 if you don't activate NewLedger or TFC_COMPARE_VZ if new ledger is on.
These programms will check the index of the data and compare the amount between index and BSEG/FAGLFLEXA table.
Second point, do you check the analysis with all same option ?
Best regards
Philippe

AR01 REPORT IS NOT TALLYING WITH GL BALANCE

Dear SAP Guru's
AR01 report is not tallying with CWIP gl. during our observation, we found that out of four CWIP assets two of them showing over balance and two of them showing under balance. but when i tried for settling these assets to actual assets, system shows no value for settlement. But when i try for Scrapping, system is allowing for scrapping from these CWIP assets. In General, when ever value is lying in the CWIP, system will allow for settlement, but why in these case it is not allowing. What could be the reason ..for .CWIP assets shows Under/Over value.
Please advice.
regds

Dear Ravi..
Thanks for your early reply...
01. As per the Program documentation, it shows that these report should be executed only before year end closing.
Is there any effect if i execute now.
02. For Your information, i know the exact difference of balance which both AR01 and CWIP GL shows, so to what extent this program ABST2)will help.
03.It would be helpful to me if you have any solution to resolve it.
04. Actually this problem was existing from more than 3 fiscal years...our auditors did not recognize it..now management recognised and want to rectify. If i reverse any entries it will effect previous Statutory reports, so without effecting the previous statements i have resolve it.
Regds,

India cash/bank book report is not matching with GL balance

We have Changed one segment in cash account and cash clearing account for internal petty cash account.
After changing the segment, Closing balance of India cash/bank book report is not matching with GL balance.
Please help.
Regards
Suresh

user702249 wrote:
We have Changed one segment in cash account and cash clearing account for internal petty cash account.
After changing the segment, Closing balance of India cash/bank book report is not matching with GL balance.
Please help.
Regards
SureshPlease do not post duplicates -- India cash/bank book report is not matching with GL balance.

"IP and router address not consistent with subnet mask"

Hi all,
i have one of the old Powermac G5's running os x 10.3.5 "Panther" with a dual 2.5ghz processor, 512mb or ram, 160 gig hd, and no wireless card. I've been trying to hook the computer up to my network via an Ethernet cable (I have a Linksys WRT54G series router).
the problem is this: When I go through the Network utilities using the "assist me" option, select the LAN option, put in the necessary information (IP address, subnet mask, router address, and the dns host), and select continue, this message pops up:"IP and router address not consistent with subnet mask".
What I've found is that no matter if the computer is plugged in with a cable to the Ethernet port the message comes up which is very unusual.
Thanks in advance.

Have you verified that you indeed have the proper subnet entered?
Why don't you just let the Mac obtain its ip address from the router via DHCP?

APIC calibration not consistent with PM-Timer

Hi ArchUsers!!!
I'm doing some diagnostic to my laptop to make it work well and 'cause I like to solve/correct bad things.
Let's start from this error
# journalctl -b
APIC calibration not consistent with PM-Timer: 119ms instead of 100ms
# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 2
On-line CPU(s) list: 0,1
Thread(s) per core: 1
Core(s) per socket: 2
Socket(s): 1
NUMA node(s): 1
Vendor ID: GenuineIntel
CPU family: 6
Model: 15
Model name: Intel(R) Core(TM)2 Duo CPU T5800 @ 2.00GHz
Stepping: 13
CPU MHz: 800.000
CPU max MHz: 2000,0000
CPU min MHz: 800,0000
BogoMIPS: 3991.35
L1d cache: 32K
L1i cache: 32K
L2 cache: 2048K
NUMA node0 CPU(s): 0,1
Tell me if you need some other infos about the laptop!
Last edited by addamm (2014-01-03 11:42:49)

Hi ArchUsers!!!
I'm doing some diagnostic to my laptop to make it work well and 'cause I like to solve/correct bad things.
Let's start from this error
# journalctl -b
APIC calibration not consistent with PM-Timer: 119ms instead of 100ms
# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 2
On-line CPU(s) list: 0,1
Thread(s) per core: 1
Core(s) per socket: 2
Socket(s): 1
NUMA node(s): 1
Vendor ID: GenuineIntel
CPU family: 6
Model: 15
Model name: Intel(R) Core(TM)2 Duo CPU T5800 @ 2.00GHz
Stepping: 13
CPU MHz: 800.000
CPU max MHz: 2000,0000
CPU min MHz: 800,0000
BogoMIPS: 3991.35
L1d cache: 32K
L1i cache: 32K
L2 cache: 2048K
NUMA node0 CPU(s): 0,1
Tell me if you need some other infos about the laptop!
Last edited by addamm (2014-01-03 11:42:49)

Data collection task in Update mode is not posible with Original list

Hi Friends,
When I try to Execute the Task for data collection in sa38.I am getting the Error with in 9 sec.
UPDATE MODE IS NO POSSIBLE WITH ORIGINAL LIST
Message No. UCS0111
Diagnosis :
If you select the indicator"original list"the current task status is ignored.In this case,the system simulates a task run in with all of the organisational units are not yet blocked.Thus,setting this indicator is meaningful and valid only if the task is executed in test mode at tthe same time.
procedure : select the original list & Test run together.
My problem is I can not select the Test run in production server.
Can any one please help me to solve the Issue.

I Thank you all for Responding to me.
Hi Dan,
SA38 provides all the needed parameters- Con.Group,Company,Version,Fis.Year,Period,Group currency.
Iam trying to run the task with SA38 for Data Collection.
Hi Lucio,
When I Check the Fields Both the Log & Original list . The programe gives an error message "UPDATE MODE IS NOT POSSIBLE WITH ORIGINAL LIST"
Even when I tried with Log,Test Run & Original List Iam getting the Same error Message "UPDATE MODE IS NOT POSSIBLE WITH ORIGINAL LIST"
I can run the task Successfully with selecting the Log option only. But my Client need to Use both Log & Original list ( as they used to run in BIW 3.5 ) Now it we are using BI 7.
Hi Christopher,
We are running the programe UCBATCH01,with the T code SA38.
Hi Eugene,
I will look in to the link and i will Discuss with the Basis team.
Once again Thank you all for responding
Suraj.

XML Publisher rtf output not consistent with the rtf created

I am using XML publisher to generate a custom report.
The approach I folllowed:
1) AM Class: Write the VO data to XMLNode using vo.writeXML() method
2) XML Publisher Administrator Responsibility: Create a data template and attach the xml created in step1 as "Preview Data"
3) XML Publisher Administrator Responsibility: Create a rtf template (contains images and text), attach the data template (step 2) and attach the rtf created.
4) Controller class: Use TemplateHelper.processTemplate() method, passing the rtf template and the XML data from VO.
5) Verify the rtf output in application.
Issues I am having are as follows:
1) Major issue is page format. I have saved my rtf file with a different page format as below:
     File->Page Setup->Paper->Width:255 pt
               ->Height:165 pt
     File->Page Setup->Margins->Top: 12 pt
                    ->Bottom: 0.1 pt
                    ->Left: 0.1 pt
                    ->Right: 12 pt
When I open my document from the application, the margins and page setup rtf output is not retained (as given in teh doc), hence my whole layout is disturbed.
Thus, I am getting a very weird layout when I open my rtf output from application.
How can I retain the page settings?
2) I added a image, and the size of the image also is not retained as well.
And if I set the layout wrapping style anything other than "In line with text", the image does not show up in the output.
Would greatly appreciate if someone can put some light on this.

RTF & PDF output can't be exact same, we can minimize the difference by eliminating all extra spaces(Ex: from table rows, in between form fields etc.) from RTF while generating RTF output.
For reference:
BUG:8662322 - RTF FORMAT DOES NOT SHOWS WITH FIXED HEIGHT OF ROW
Thanks,
Sandeep

Colors not consistent with Snow Leopard 10.6 on an Eizo SX2761W monitor

I am unable to get any color consistency with Snow Leopard 10.6 on my Eizo SX2761W display.
Most of the actual "content" (i.e. images, videos, websites, etc.) is displayed very saturated and dark, much more saturated and dark than in 10.5.8. I presume that's because of Snow Leopard's new gamma value. The problem is, all of OS X's GUI elements, like the dock, icons and color labels in the finder, title bar buttons, etc. are not displayed in the same manner. These elements are all very desaturated, pale and grayish. NoMachine NX sessions running in X11 (via Rosetta) also have this desaturated look in Snow Leopard.
Here's a screenshot comparison I put together, that shows those color inconsistencies using the example of Mozilla's Firefox logo on the web in Safari, on the web in an NX session and as an icon in the Finder and in the Dock:
http://dl.getdropbox.com/u/7276/SnowLeopard-ColorsAndContrast.png (1 MB)
As far as I could test it, I get these color/contrast discrepancies only on the Eizo SX2761W monitor. I checked this on a classic Mac Pro and a late Mac mini with the same results. On a MacBook and its internal display Snow Leopard's colors seem consistent.
I tried to recalibrate the SX2761W profile, I tried out all the other standard color profiles available in Snow Leopard, I tried to copy my old profiles over from a Leopard backup, but I was unable to get rid of the display inconsistencies. After a whole day of trying and tinkering I went back to 10.5.8 to get a consistent color environment back.
Any ideas what's causing this and more importantly what to do about it? I have to say I'm at my wits end. The only thing I can think of is mailing this issue to Apple in the hope there will be a point release in the not too distant future that fixes the problem.

I have what I assume is the same problem. It just started today on my DELL WFP2407 - but remains even when switching to my MacBook Pro's built in screen.
The Dock, Safari, the desktop background - and probably other colour managed applications; all show very pale blue hues with over saturated red. Blue goes towards purple and other colours get muddled and pale. Oddly the Finder displays colours correctly on icons, but not the dock. I took a screenshot of Finder's Safari icon next to The Dock's:
http://www.nuxx.dk/hosting/paledock.png
- Clearly showing significant inconsistency... I just updated to 10.6.1 which didn't change anything.
Needless to say I tried calibrating a new colour profile to no effect, and seeing as the finder itself renders things just fine I'm not sure that's where the issue lies.
This is a huge problem for me, I hope there is a simple solution.
Message was edited by: nuxxie

The rendered records are not consistent with the range

After changing the range with record navigator to render the records,
if navigate to other page and go back,the rendered records will not be
consistent with the record range.
The issue can be reproduced as follows.
1.when select 1-10 range,the first 10 records are rendered.
2.select [Next 10 records] to render the 11-13 records.
3.change to other page and return to the original page.
It is found that the 11-13 records are rendered but the range is 1-10.
You can verify the issue by executing SampleMainPG.xml of the Tutorial.jpr for 11.5.10.2
from Jdeveloper after changing the SampleMainCO.java as below.
* Layout and page setup logic for a region.
* @param pageContext the current OA page context
* @param webBean the web bean corresponding to the region
public void processRequest(OAPageContext pageContext, OAWebBean webBean)
super.processRequest(pageContext, webBean);
if (pageContext.getTransactionValue("link") != null)
OAAdvancedTableBean inner = (OAAdvancedTableBean)webBean.findChildRecursive("InnerTable");
inner.clearCache(pageContext);
inner.setAttributeValue("CLEAR_CACHE_ONCE_NOEXECUTE_ATTR", Boolean.TRUE);
<==comment out these original source above.
OAAdvancedTableBean outer = (OAAdvancedTableBean)webBean.findChildRecursive("OuterTable");
outer.queryData(pageContext, false);
<==add the two rows of source above to get the latest query data.
you should to make the records of the table fwk_tbx_employees to be more than 10 just using the SQL script below.
(just need to change EMPLOYEE_ID at your will)
INSERT INTO fwk_tbx_employees (
EMPLOYEE_ID,
TITLE,
FIRST_NAME,
MIDDLE_NAMES,
LAST_NAME,
FULL_NAME,
EMAIL_ADDRESS,
MANAGER_ID,
POSITION_CODE,
SALARY,
START_DATE,
END_DATE,
LAST_UPDATE_DATE,
LAST_UPDATED_BY,
CREATION_DATE,
CREATED_BY,
LAST_UPDATE_LOGIN,
ATTRIBUTE_CATEGORY,
ATTRIBUTE1,
ATTRIBUTE2,
ATTRIBUTE3,
ATTRIBUTE4,
ATTRIBUTE5,
ATTRIBUTE6,
ATTRIBUTE7,
ATTRIBUTE8,
ATTRIBUTE9,
ATTRIBUTE10,
ATTRIBUTE11,
ATTRIBUTE12,
ATTRIBUTE13,
ATTRIBUTE14,
ATTRIBUTE15 )
VALUES (
17,
'ichiro',
'yamada',
'ichiro yamada',
1,
0,
sysdate,
sysdate,
sysdate,
0,
sysdate,
0,
0,
it seems that if use the functions below,the issue can be workarounded.
But it is not clear whether there is any other impact from these functions.
innerTable1.clearCache(pageContext);
innerTable1.setAttributeValue("CLEAR_CACHE_ONCE_NOEXECUTE_ATTR", Boolean.TRUE);
Could you please share your idea?
Thank you very much in advance.
Best regards,
Wang

FYI. I was able to do what I wanted by first going to page properties and removing unwanted fonts from appearance. Then edit the page, select all, change style to normal, then select the text where you want to use a different style and change style there. This gives consistent appearance with both browsers.

Console cluster reporting is not consistant with dynamic list

Similar Messages

Maybe you are looking for