Console won't Connect and wierd password prompt.

Hi, I have a Nintendo DS Lite console and I am trying to access the internet. When I do access the internet my DS kept saying "connection error." Afterthat my game freezes. The game that I am using to connect to the internet is Pokemon Platinum. Also I am frustrated that the server (Wireless-N Broadband Router WRT160Nv2) keeps prompting me the password every time. Any help would be appreciated

WRT160N v2 router should be downgraded to firmware v2.0.02 build 008...Check if you have firmware v2.0.02 build 011...You will find the downgrade here
Do not forget to reset your router after the downgrade...
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Similar Messages

My wireless keyboard and trackpad won't connect and i can't sign in

my wireless keyboard and trackpad won't connect and i can't sign in. yesterday I tested it with my mac air and it worked fine. i deleted the connection from my mac air and tried it again. then it worded. howerver, i shut down my computer correctly and tried it again today. now the same problem again.
HELP!!

no, just a usb mouse. but I found an old usb bluetooth hardware. this made it possible for me to make it work. but as soon as I remove the hardware it says "no bluetooth available"! I re-istalled mountain lion but still the same problem.
additionally I deleted/reset the PRAM. still the same problem.

ITouch won't connect and doesnt' show IP Address

I have been connecting to my home wifi without a problem. All of a sudden, I can't connect. Other wireless devices connect without a problem. My iTouch does connect without a problem on other wifi networks. My iTouch sees my wifi network, but no IP Address or other data is showing on the iTouch. HELP!

sunnhausl wrote:
I tried that already, too! New development...I have the same problem in my office now. So, clearly, it is a problem with my iTouch. It recognizes the networks, won't connect, and when I go into look at the network, there is not data (IP address, etc.) It's just blank. HELP!
You could try restoring the S/W on your iPod Touch. If that doesn't work you may need to talk to Apple about repair.

My computer was trying to connect to my Bluetooth mouse but I accidentally hit cancel so now my computer won't connect to my mouse. I turned my computer off. When I turned it back on it still won't connect and I can't login! Help!

NEED URGENT HELP!
My computer was trying to connect to my Bluetooth mouse but I accidentally hit cancel so now my computer won't connect to my mouse. I turned my computer off. When I turned it back on it still won't connect and I can't login! Help!

Reset the SMC.
Barry

SCCM Console Won't Connect to Site Server WMI Connection Issues

Ok, I've been scratching my head with this one for a while. We're running SCCM 2007 R3 in native mode, site server is Win 2008 Std R2, Config Mgr database sits on a seperate SQL box. When I launch the console (user account I use when logged into server
which is a member of SMS Admins group) on my Win 7 machine I receive the error..
The ConfigMgr console could not connect to the Config Mgr site database. Verify that this computer has network connectivity to the SMS Provider computer and that your user account has Remote Activation permissions on both the Config Mgr site server and SMS
Provider computers
I've read numerous articles around DCOM permissions, I can confirm have all been set on the site server and SMS Admins group has the Remote Activation permission checked. Also I can open WMI, select properties to view the WMI namespace structure, permissions
on the SMS folder and subfolders are set as per microsoft articles.
So then I launched wbemtest from my Win 7 machine, when I try and connect to
\\[SiteServer]\root\sms\Site_SiteCode. I receive WMI error below. I can however connect successfully to WMI on any other server
Number: 0x80070005
Facility: Win32
Description: Access is denied
When logged into SCCM Site server and open wbemtest I can't remotely connect using WMI to any server in our domain, each time receiving the error below.
Error
Number: 0x800706ba
Facility: Win32
Description: The RPC server is unavailable
Whilst logged onto the site server I can use wbemtest to connect to itself using the SMS Provider namespace(\\[SiteServer]\root\sms\Site_SiteCode) which would suggest the WMI isn't corrupt.
It appears that I can't connect remotely to or from this machine using WMI, that something is blocking or not allowing the connection maybe? Please note the Windows Firewall is disabled, we don't use any third party firewall software on our servers and
WMI service is started.
Any ideas or suggestions on this one would be most welcome.
Cheers

Hi Eswar, thanks for the reply. This is the extract from the adminUI.log when I try and launch the console
[6][20/01/2012 10:24:21] :Insufficient privilege to connect, error: 'Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))'\r\nSystem.UnauthorizedAccessException\r\nAccess is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))\r\n
at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo)
   at System.Management.ManagementScope.InitializeGuts(Object o)
   at System.Management.ManagementScope.Initialize()
   at System.Management.ManagementObjectSearcher.Initialize()
   at System.Management.ManagementObjectSearcher.Get()
   at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.Connect(String configMgrServerPath)
   at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.GetConnectionManagerInstance(String connectionManagerInstance)\r\n
[6][20/01/2012 10:24:21] :Microsoft.ConfigurationManagement.ManagementProvider.SmsConnectionException\r\nThe ConfigMgr Administrator console could not connect to the ConfigMgr site database. Verify your user has read permissions to the ConfigMgr site and then
try to connect again.
\r\n   at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.GetConnectionManagerInstance(String connectionManagerInstance)
   at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.BuildTreeWorker()\r\nAccess is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))
\r\nSystem.UnauthorizedAccessException\r\nAccess is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))\r\n   at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo)
   at System.Management.ManagementScope.InitializeGuts(Object o)
   at System.Management.ManagementScope.Initialize()
   at System.Management.ManagementObjectSearcher.Initialize()
   at System.Management.ManagementObjectSearcher.Get()
   at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.Connect(String configMgrServerPath)
   at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.GetConnectionManagerInstance(String connectionManagerInstance)\r\n
[8][20/01/2012 10:25:37] :Insufficient privilege to connect, error: 'Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))'\r\nSystem.UnauthorizedAccessException\r\nAccess is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))\r\n
at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo)
   at System.Management.ManagementScope.InitializeGuts(Object o)
   at System.Management.ManagementScope.Initialize()
   at System.Management.ManagementObjectSearcher.Initialize()
   at System.Management.ManagementObjectSearcher.Get()
   at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.Connect(String configMgrServerPath)
   at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.GetConnectionManagerInstance(String connectionManagerInstance)\r\n
[8][20/01/2012 10:25:37] :Microsoft.ConfigurationManagement.ManagementProvider.SmsConnectionException\r\nThe ConfigMgr Administrator console could not connect to the ConfigMgr site database. Verify your user has read permissions to the ConfigMgr site and then
try to connect again.
\r\n   at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.GetConnectionManagerInstance(String connectionManagerInstance)
   at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.BuildTreeWorker()\r\nAccess is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))
\r\nSystem.UnauthorizedAccessException\r\nAccess is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))\r\n   at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo)
   at System.Management.ManagementScope.InitializeGuts(Object o)
   at System.Management.ManagementScope.Initialize()
   at System.Management.ManagementObjectSearcher.Initialize()
   at System.Management.ManagementObjectSearcher.Get()
   at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.Connect(String configMgrServerPath)
   at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.GetConnectionManagerInstance(String connectionManagerInstance)\r\n
[3][20/01/2012 10:25:48] :Failure while loading required 'WQL' query engine, console cannot connect

Ellipsis Jetpack won't connect and now won't even turn on

I have been having a problem with my Toshiba running Vista , connecting to my Ellipsis jetpack. I called customer service and while the rep was very courteous and helpful, she stated the problem was a security issue with my laptop. I took several measures to disable the security features but to no avail. Finally, I took the laptop and jetpack in to Verizon yesterday to get some answers. Two different service reps attempted to solve my problem. The second rep finally told me that this is a known problem with Vista/Ellipsis compatibility. He kindly offered the solution of upgrading to a newer version of Windows. After returningbhome and doing some research, i find that my Toshiba doesn't meet the requirements to upgrade. Does this mean I have to buy a new computer to connect to my jetpack???? On top of that, the jetpack shut down this morning while I was actually connected and working online, and now it won't turn back on, even after a hard reset. Frustrated and dissatisfied. Can anyone help???

I too have an Ellipsis jetpack. Unfortunately the Verizon CSR(s) you spoke to gave out a lot of misinformation.
Since you've been able to connect to the Ellipsis in the past it should not be an encryption issue (security). However you could log into the Ellipsis and change the security from WPA2 to WPA to see if that resolves your problem. Do you have the ability to connect a different wireless device to see if it can connect and remain connected?
There are no "compatibility issues" with systems running Vista and connecting to the Ellipsis.
If your laptop runs Vista then it will handle Windows 7 or 8. Most drivers should be installed automatically, but you may have to find some on your own.
Regarding the power issue:
Pull the power cord & battery out of the Ellipsis for 10 min, then reconnect and hold the power switch to power it on.
I would also recommend that you see if there is a driver update for your wireless adapter. Don't just rely on Windows Update or Toshiba's website either. Get the model # of the adapter and go to the mfg's site for the latest driver - especially if it's Realtek, Intel, or Atheros since they are often updated.

IChat won't connect and Software Update will not run.

Hi, all,
Sorry if something like this has already come up, and I apologise if this is the incorrect forum to post this in. I searched and didn't see anything identical to my issue (I didn't search very hard, but I did search), so I figured posting a topic might be the best way to go. I know this is two problems, but I decided to post it in the iChat forum in case the two were related.
I bought this computer and received it yesterday. It's a 15 inch MacBook Pro, i5, 10.6.4. It worked fine this morning, software update ran, ichat worked fine.
Now, when I try to connect to iChat, it takes a good ten minutes to try to connect, and then it sends me an error that says "You have been disconnected from iChat services. An internal error occurred that disconnected you from all iChat services. To resume using iChat, log in again to your instant messaging account." So, I quit iChat, and restarted it, but now it won't even show me my buddy list saying "connecting....". It just starts and sits there, and all the options are greyed out. I tried going into the security settings and changing the port to 443, but that's greyed out, too.
So I thought I would try to run software update, and software update opens, but it doesn't ... go. It shows the little blue bar, and it's not frozen, but it doesn't advance at all, and it never gives me the option to go to the "install updates" screen because it doesn't check. I went into my network settings to check my connection, and I'm definitely connected to the internet (I mean, I'm typing this ON the MacBook Pro right now), but the panel says I'm not. I can hit "cancel" and quit software update.
I already reinstalled the OS and the update to 10.6.4, and it's still the same issue.
Help, anyone? This computer is brand new and I really don't want to have to erase and reinstall.
Thanks

Hi,
Welcome to the  Discussions
On the changing the port front stop off on the Account Info tab on the way a deselect "Use this Account" to take it Off Line. (you can get half way states)
You should then find the port 5190 is dark text so it can be edited.
You should press the Enter key to "Set" the port change (this is different to earlier versions of iChat)
Also try it with the SSL option disabled.
If this is an AIM Login (AIM or Apple Name) their SSL server is more prone to "Falling over". iChat should default to using an Non SSL Login on a reconnection front it can be subject to a time frame issue.
Next check the Mac Firewall (System Preferences > Security > Firewall tab)
If this is On in Snow Leopard you have to go to the Advanced Button and Allow Signed Apps and Add iChat to the list.
I favour the last suggestion as this may also block Software Update (Although I nm not sure how you got to 10.6.4 although it is a separate Download you can get).
I would also check you have DNS servers listed in System Preferences > Network > Advanced Button > DNS tab
9:14 PM Saturday; September 25, 2010
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"

Canvio 3.0 won't connect and now won't power up

My Canvio 3.0 (1T) was working fine.
First used it with a Inspiron 1501 with Win 7 32 bit, then with a new HP dv7 with Win 7 64 bit.
A week ago, I plugged it in, the laptop didn't see it connected. I unplugged cord, plugged it in again on both sides, power came on and then went out. It didn't come back.
I thought cable was messed up and bought a new one.
Same behavior. Power came on but HP never saw it connected.
I tried disconnecting and plugging in again, and now no power.
Any ideas?
Thanks.

I am using USB 3.0 ports. On more research, the majority of people are having the same problem after a few months using these drives. The connection at the back gets loose and won't connect anymore. I've tried wiggling it, but it only connects for a second at best.
Anyone found a way to get it to connect? I've even gotten a new cable; it's the drive, not the cable.
I can't believe this. Toshiba used to be better than this.

Can see Airport Express, but iTunes won't connect and more..

I'm running Mac OSX 10.4.2 on an Aluminium PowerBook G4, connected to an Airport Extreme Base Station - which can use the internet etc easily. I have an Airport Express, which can be seen & changed in Airport Admin, and can be seen in iTunes - but can not be connected to in iTunes - it tries for about 30 seconds, and then gives up, not even an error message? I'm not sure if it's a related issue, buit an old iBook running OSX 10.3.9, connects to the same Airport Express, no problems. But the PowerBook, whilst it can see the iBook, won't connect to the iBook via Airport - it tells me it is not operational, or something.
Can anyone think of anything that may fix the problem?
Thanks in advance.

Is this a new problem on this Powerbook - or has it never worked? While there are many (and some very obscure) causes for this problem, one of the more common causes is firewall software of some sort. This also includes applications designed to monitor outgoing network data (like spyware) on a Mac, like "Little Snitch".

Applescript "with administrator privileges" and without Password prompt

i,
I have to configure some phone settings in the central VOIP/VPN/Gateway Router via a ssh (with certificate) command.
There is only a option to allow or disallow the ssh access in the router. Therefor I wrote a applescript to allow only the specific ssh command "set /Setup/Voice-Call-Manager/Call-Router/Call-Routing/". To avoid the configuration access for anyone and to hard code passwords I have to execute this script with root permissions (do shell script "/usr/bin/su - " & user & " -c " & "'" & cmd & "'" with administrator privileges"). In any other unix implementation I can use "chmod 4755; chown 0:0". Even I compiled the Applescript and stored it as Carbon App, I get a user/password prompt.
How can I avoid this prompt or authorize the script/app in any way?
Thanks Henri

I agree, but to use the private key of the applescript caller opens any user the ability to change any WLAN key, VPN settings or delete the admin account, not a good idea....
Therefor I would like to run the applescript with root, "su - <adminuser> ssh router set ....".
This restricts the access to the router config to this applescript and I would like avoid the hard coding of the root password in the applescript.
I tried also the add the command to /etc/sudoers, this work fine from the command line but how to call "sudo applescript" from the desktop without entering the admin password?
Thanks
Henri

My iPad won't work and has a prompt on the screen saying "iPad is disabled. connect to iTunes." What does this mean? What am I supposed to do?

See problem above.

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug (very important)
5. Release Home button.
ON COMPUTER
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. Select "Restore iPad"...
Note: Data will be lost

Jdeveloper 10.1.3.2 and sqlplus password prompting

OK,
I downloaded jdeveloper 10.1.3.2. Created a new database connection, let's call it 'TestDBConnection'. In the authentication tab, made sure 'deploy password' was checked. Tested database connection everything works. So far so good.
Now create a pl/sql procedure. i.e
create or replace procedure test
is
begin
null;
end;
right click on file, select 'Run in sql*plus', click on 'TestDBConnection'.
Sql*plus comes up 'BUT' it prompt for a password!!!!!
WTH!!! 10.1.2 never had this 'problem/feature' this is sooooo annoying. Everytime I want to compile a sql file from JDeveloper, I have to type in the password!
Anyone know a work around for this?

This is a security requirement we had - since we don't want to pass the password visibly to SQLPlus.
A workaround for this is to go into tools->External Tools and add an option that will invoke SQLPlus with the user/pass you want and pass the name of the file you are on to it as a parameter.

Wifi unable to connect and incorrect password problem/issues

since i updated to iOS5.1 i started having a problem with our wifi connection. it is locked but even though i enter the correct password my itouch is promting that i have punched in an icorrect password itried using a different iDevice and punched in the same password it's all good, they can connect in our wifi and most of the time i receive an error "unable to join the network" if im trying to connect to an open network. what seems to be the problem? can somebody help me with this one?

- Reset the iPod. Nothing is lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections

2012 r2 Remote Administration console won't connect to the server

Hi,
I have now migrated my Data Protection Manager 2012 r2 to new hardware and now I can't connect from my PC to the new server with the Admin Console with my domain admin account. I can connect with an Enterprise Admin account.
Which group do I need to be in to allow access? Although we were running 2012 r2 before it was on Windows 2008 r2 and had been upgraded from Data Protection Manager 2010, Data Protection Manager 2012 to Data Protection Manager 2012 r2.
Best wishes
Michael

Hi, please ad your User to the local Admin Group on the Server, should work
Seidl Michael | http://www.techguy.at |
twitter.com/techguyat | facebook.com/techguyat

My Ipad 2 won't connect WiFi, says password incorrect.

Sorry, seem it won't let me delete this post.
Somehow my Ipad 2 finally connect to my WiFi.
I have no idea how did it cause.
So never mind. My problem is resolve.
Message was edited by: Abcv2v

Yes, same here! iPad 2 32G. No 3G.
Will not connect to internet even with correct wifi pass.
Multiple crashes during attempted sync and the "Books" application was deleted from Apps.
Need to use tonight, please help!

Console won't Connect and wierd password prompt.

Similar Messages

Maybe you are looking for