Constant disconnect/reconnect and tons of errors.
Ijust got a brand new iphone 4, and just installed newest itunes fresh a couple of days ago.
The computer is running windows xp pro, and was just recently reinstalled about a month ago.
When I plug my iphone into the computer it will start to sync and then stop an give me an error either about "error reading device, iphone not connected," or an error with a hex code, or all of the above and others.
Heres what happens
I plug the phone in, the battery icon changes to a plug, then the lightning bolt, then back to normal, the phone tells me charging is not supported with this accessory, and sync in progress.
Windows pops up the autorun menu and asks me what I want to do with the connected camera, open it in word, or scanners and cameras.
Itunes also opens and starts the sync process, it shows syncing on the iphone.
then after backing up and copying some apps, the iphone goes back to the home screen as if it was unplugged, the sync stops and gives me errors.
I'm getting extremely frustrated with this too. If I leave it plugged in I constantly keep hearing the whistle noise the phone makes when it's plugged in, and windows wont shut up with the usb device plugged in/unplugged sound.
It will just keep disconnecting, trying to sync, failing and doing it all over again until I unplug it.
I've restarted the phone, restarted the computer and it still does this.
Do I have to unplug all of my other usb devices? it totally gets confused if I have a flash drive or another phone (my ROKR E8 or RAZR) plugged into the computer.
Sorry to tell you this but the iPhone is not a storage or backup device! Occasionally it will have problems, an app may be corrupted and cause problems! Because of this you will need to do one of the three (restart, reset, restore). You really need to backup everything on phone somewhere on your computer or a backup drive! Old phones stored contacts on the Sim... the iPhone doesn't... If you rely completely on your iPhone backup you may be sorry because that can get corrupted also!!
Again sorry to tell you this but having an iPhone when you dislike iTunes and refuse to backup (besides iPhone backup) is a bad decision... Not backing up is a bad decision with any smart phone!!! They're no longer plain old phones!!!
Similar Messages
-
I have had this error for 2 days now.. roughly since the upgrade to FireFox 31 .. I have uninstalled/ reinstalled ..disconnected / reconnected .. logged in and out and in to sync.
"Sync encountered an error while syncing: Unknown error. "
I updated my other devices to FireFox 31 and it does not help ..
Any suggestions appreciated thanks much!Hello,
To find the correct solution to your problem, we need some more non-personal information from you. Please do the following:
# Use ONE of these methods to open the Firefox Troubleshooting Information page:
#* Click the menu button [[Image:New Fx Menu]], click on help [[Image:Help-29]] and select ''Troubleshooting Information''.
#* Type '''about:support''' into the Firefox address bar and press the enter key.
# At the top of the Troubleshooting Information page that comes up, you should see a button that says "Copy text to clipboard". Click it.
#Now, go back to your forum post, right-click in the reply box and select '''Paste''' from the context menu (or else click inside the reply box and press the Ctrl+V keys) to paste all the information you copied into the forum post.
If you need further information about the Troubleshooting information page, please read the article [[Use the Troubleshooting Information page to help fix Firefox issues]].
Thanks in advance for your help! -
Constant home wifi disconnect/reconnect with GS3 and GS4
I've been having terrible trouble with my previous Galaxy S3 and my new Galaxy S4 on my home wifi network. They CONSTANTLY disconnect and reconnect. Sometimes it can happen 2 or 3 times in 1 minute, and sometimes it won't happen for 5 or 6 minutes, but then it will happen and it will happen 2 or 3 times in rapid succession. This is really irritating when I'm viewing a web page and it has to reload EVERY time the disconnect/reconnect happens.
What can I do to keep my GS4 from doing this?
I have the Verizon GT704WGB DSL modem/wireless router.
I have my laptop and my Kindle Fire HD connected via wifi to this router, and they never experience the problem, only my GS3 and GS4.
Any help in this matter would be greatly appreciated.Hi TR_Young,
We're here to help! Have you tried resetting your router? Do you know if your Wi-Fi router needs to be updated? I understand wanting the phones to stay connected to Wi-Fi. Do the phones having problems have trouble on other Wi-Fi networks? We look forward to hearing from you about these details.
ElizabethE_VZW
Follow us on Twitter @VZWSupport -
Disconnect users and Reconnect users
Hello my name is Marc,
i have a problem, in my office use adobe connect 8, and server hosted privatly in my office. I have many meetings with other offices and one day appear different problems.
The first problem: one day i stay in a meeting with 10 people, and one moment all users disconnect and reconnect and when i reconnect all user appear double for example: "Marc" and "Marc2". I clean cookies and changed browser explorer and solution this problem but the other people don't find a solution.
The second problem: other day i stay in a meeting with 8 people, and 2 o 3 people i'm not sure disconnect and reconnect and appear the same previous case. But in this meeting, the host rec's meeting and desynchronized video i don't find what's is the error.
When the problems appear, i check the server's log and server don't detected anything, the brezze logs detected when the users disconnect and reconnect in a meeting, but the server don't detected error, no errors in applications, no errors in network and no errors in a system. I can't find who is the error .
Thanks for you help.
P.D: Sorry for my english, my level is very basic
Good BYE!!
by: MThanks sni,
yes this problem appear when every users are present in the room, i think the problem is in network server but the server don't recognise the problem, no detected any problem. It's more strange i hope resolve this problem. Thanls for you help sni.
Good Bye -
To save battery, I leave my wifi off when the TP's screen is locked. At home, my TP has no problem reconnecting to wifi after the screen is unlocked. However, at work, which uses enterprise wifi, I can only connect the first time. If I lock the screen and then unlock it (causing the wifi to turn off and on again) then the TP will not reconnect and I would get the "Association failed" error over and over again. If I were to turn the TP off and on again, I would still get the same error. Here's the strange part, if I come in work the next day, it would be able to connect to the wifi. If I were to leave the wifi on all the time, it would not disconnect even if I lock the screen. Now if I were to turn off the wifi and then turn it on again, the TP would not reconnect. So it seems like the TP can only connect the first time each day....very strange...and frustrating.
Post relates to: HP TouchPad (WiFi)Scimmia is right. But you AcousticBruce are still very wrong. You claim there were no error messages. Yet after much proding and denial you finally provide small portions of error messages which fully identify the problem and can be found in many other posts in these forums. Yet still, you haven't actually provided full output - instead you paraphrased the output after a couple of "//" symbols.
If you don't give us the actual output we can't help - except in this case the error is so common we could very easily help. So could the wiki page on wpa_supplicant if you had read it, as your problem is explictly listed there in a "NOTE" box. But more importantly if you are reluctant to give us actual output we will not want to help you.
This issue would have been solved instantly if you would have provided the actual output instead of lying about it.
The relevant wiki pages:
https://wiki.archlinux.org/index.php/WP … passphrase
https://wiki.archlinux.org/index.php/He … er_or_root
And the related forums posts found after just a quick search of that error message that you finally provided:
https://bbs.archlinux.org/viewtopic.php?id=167244
https://bbs.archlinux.org/viewtopic.php?id=184824
https://bbs.archlinux.org/viewtopic.php?id=178909
https://bbs.archlinux.org/viewtopic.php?id=190097
https://bbs.archlinux.org/viewtopic.php?id=191351
https://bbs.archlinux.org/viewtopic.php?id=191964
Last edited by Trilby (2015-05-18 11:08:44) -
Please help my ipod disconnected from the Internet and wont reconnect and i did the right password
please help my ipod disconnected from the Internet and wont reconnect and i did the right password
- Do other devices still connect to the network?
- Does the iPod connect to other networks?
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router.
- Reset networks settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- iOS: Recommended settings for Wi-Fi routers and access points -
I have this iPod Nano 6G. I try to erase and sync it. It told me that I have to restore it. My Nano displays a white screen and said that do not disconnect. I press ok in itunes and tells me error occurred 1439. What should i do? :(
Hello dreyc,
The following article provides information and troubleshooting steps that can help resolve this error.
iPod: Can't restore or update in iTunes with error 1415, 1417, 1418, 1428, 1429, 1430, 1436, or 1439
http://support.apple.com/kb/TS1372
Cheers,
Allen -
I went into recovery mode - and keep receiving error 4005 - tried different usb, computers, did all updates possible nothing helps, my iphone screen shows apple logo and constant waiting circle
Same here. I tried to update my iPhone 5S and iPad 4 to 7.1 but iTunes wiped out them. This thing already happened for iOS 7.0.6 update. What happened to Apple? I am really curious whether Apple is aware of this problem.
-
Adobe Installer stalls @ 50% with error lost connection... reconnecting and hangs up
Adobe Installer stalls @ 50% with error lost connection... reconnecting and hangs up. Can any one help please? I've Windows 7 and using internet explorer.
you can use the links below. if you have the same problem, you can try a different browser and/or a different wired connection and/or a download manager.
Downloadable installation files available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
Photoshop Elements: 13 |12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
Lightroom: 5.7.1| 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5.5, 5 | 1
Contribute: CS5 | CS4, CS3 | 3,2
FrameMaker: 12, 11, 10, 9, 8, 7.2
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'. -
I have a HP 6600 and it says Error no toner and it won't print
I have a hp 6600 and it says error no toner and it won't print
Hello garylee1,
Welcome to the HP Forums!
I understand your Officejet 6600 states no ink cartridge. I will do my best to assist you! I would recommend following this entire HP document on A 'Cartridge Problem,' 'Ink Cartridge Failure,' or 'Incompatible Ink Cartridges' Error Message Displ....
Are you using Genuine HP ink cartridges? Please post your results, as I will be looking forward to hearing from you. Have a great night!
I worked on behalf of HP. -
hello good evening. my iphone 3g I try to restore with itunes and not completed the restoration gets stuck and disconnected and brand UNKNOWN ERROR -1. can help me please.
Try a different cable...
yescadnk wrote:
... UNKNOWN ERROR -1. can help me please.
Error -1
Attempt to restore your iOS device two more times.
If the issue is still unresolved, the device may need service.
From Here > http://support.apple.com/kb/TS3694 -
I am trying to download itunes 10.7 and keep getting "error writing to file C\config.msi\6f8a6.rbf" Can anyone help?
Are you running Kaspersky security software on that PC? (There's been a few reports in recent times of Kaspersky interfering with iTunes installs, with that message being produced.)
If there is Kaspersky on board, we should try some general-principles getting-past-security-software-interference troubleshooting.
Download and save a fresh copy of the iTunesSetup.exe (32-bit installer file) or iTunes64Setup.exe to your Hard drive. (Don't run the install on line, and don't start the install just yet.)
http://www.apple.com/itunes/download/
Restart the PC. After the PC restarts do not open any applications. Disconnect from your network and/or the internet. Now switch off all your security software (firewall, antivirus, antispyware).
Now start the install by doubleclicking the iTunesSetup.exe (or iTunes64Setup.exe) file you downloaded earlier.
Reenable all security software prior to reconnecting to your network and/or the internet.
Any better luck with the security software shut down? -
New Homehub - Lots and lots of errors?
Hi,
I recently upgraded to the black homehub 2.0 (version A even though I asked for a version B) from my old white version 1.5. Plugged it in, everything went smoothly. The download data is half what it was before, but Im guessing it'll settle out in a few days or after a few power cycles as the broadband is a bit unstable at the moment (off and on.. off and on..)!
The weird thing is, is that Im getting a ton of Errors apparently, I dont know if its normal so I thought I'd post here and find out!
ADSL line status
Connection informationLine state Connected
Connection time 0 days, 0:01:50
Downstream 2,902 Kbps
Upstream 547 Kbps
ADSL settingsVPI/VCI 0/38
Type PPPoA
Modulation ITU-T G.992.3
Latency type Interleaved
Noise margin (Down/Up) 6.1 dB / 6.0 dB
Line attenuation (Down/Up) 64.0 dB / 39.0 dB
Output power (Down/Up) 0.0 dBm / 12.9 dBm
Loss of Framing (Local) 11
Loss of Signal (Local) 1
Loss of Power (Local) 0
FEC Errors (Down/Up) 390 / 4
CRC Errors (Down/Up) 0 / 2147480000
HEC Errors (Down/Up) nil / 20
Error Seconds (Local) 2
Is this normal, or has something gone wrong?
Regards,
TomDont worry, I repasted all the hub details but forgot to update the previous paragraph . Speed has returned to normal now at around 2200. Its already in the master socket, so I'll just plug it into the test one.
Before plugging it into test socket:
ADSL line status
Connection informationLine state Connected
Connection time 0 days, 0:01:32
Downstream 2,336 Kbps
Upstream 563 Kbps
ADSL settingsVPI/VCI 0/38
Type PPPoA
Modulation ITU-T G.992.3
Latency type Interleaved
Noise margin (Down/Up) 1.5 dB / 6.4 dB
Line attenuation (Down/Up) 62.0 dB / 39.0 dB
Output power (Down/Up) 0.0 dBm / 12.9 dBm
Loss of Framing (Local) 22
Loss of Signal (Local) 12
Loss of Power (Local) 0
FEC Errors (Down/Up) 9219 / 0
CRC Errors (Down/Up) 356 / 2147480000
HEC Errors (Down/Up) nil / 8
Error Seconds (Local) 7
Plugged into test socket:
ADSL line status
Connection informationLine state Connected
Connection time 0 days, 0:01:01
Downstream 2,983 Kbps
Upstream 520 Kbps
ADSL settingsVPI/VCI 0/38
Type PPPoA
Modulation ITU-T G.992.3
Latency type Interleaved
Noise margin (Down/Up) 5.8 dB / 5.5 dB
Line attenuation (Down/Up) 62.5 dB / 39.0 dB
Output power (Down/Up) 0.0 dBm / 12.9 dBm
Loss of Framing (Local) 33
Loss of Signal (Local) 15
Loss of Power (Local) 0
FEC Errors (Down/Up) 749 / 0
CRC Errors (Down/Up) 0 / 2147480000
HEC Errors (Down/Up) nil / 8
Error Seconds (Local) 172
I also have a ADSL plate on my master socket (it has a microfilter built in) so to test the test socket of course I plugged in an external microfilter.
What does these results say, the internet has been dodgy all day.. not staying up for ages (but reconnecting quite quickly).
Thanks,
Tom -
Windows 7 keeps freezing, disconnecting/reconnecting USB devices
Last week, a lightning strike near where I live caused a power surge and as a result, my ethernet card was fried. I took my computer (iMac) to a store to have it repaired, and they wound up replacing the entire motherboard (a bit extreme in my opinion, but what do I know).
When I got it back today, sure the ethernet problem was solved, but I noticed that my taskbar was acting weird - specifically the icons in the notification tray. Lots of them were "blank", meaning there were just empty spaces that would highlight when I hovered the cursor over them, but nothing happened when I clicked them.
Then I discovered that clicking any of the icons in the notification tray almost immediately froze the computer. Frozen, as in completely unresponsive to the point where my only option was to manually shut off the computer. That happened twice.
My solution was to reboot in safe mode and run system restore to an earlier point. That fixed the notification tray problem (no more freezing, and the icons were all back), but the computer still keeps freezing at random intervals. Again, my only solution is to manually shut it off by holding down the power button, which I hate doing because I know it's bad for the hard drive. Sometimes it froze as soon as the welcome screen. I tried running a virus scan, but again it froze in the middle of the process.
On top of the constant freezing, it keeps disconnecting/reconnecting my usb devices. My mouse and keyboard will suddenly drop out for five seconds and then start working again. This constantly happens, to the tune of several "disconnect" sounds playing over the speakers.
What the heck is going on? I tried re-installing the Boot Camp drivers, but that didn't work. I have my Windows 7 CD and backed up files, so if worse comes to worst I can do a clean install of Windows, but I'd rather not have to spend a day re-building my computer, and I'd REALLY rather not take it back in for another repair, since that took a week and I need this for my work.
Any ideas on what I should do? I'm out of town on my laptop for the weekend, and I'd like to have a game plan for when I get back.I'm very excited to finally have a solution for this problem. Thank You Balaji for figuring this out. I've been struggling with this for a number of years, and had only one USB Hard Drive that worked. I too have VMware workstation, and had the missing files
in "c:\windows\inf." I can say with certainty that I did not delete the files from that folder, but something is common in both of our situations. Maybe it has to do with VMware, and some of it's updates over the years. I'm also using nCompute to share out
a networked desktop via the wire.
One more thing worthy of mention is this machine was an update from Windows Vista, and the USB hard drive that worked was configured back than. So although I could never add another HD, at least I had the one.
Now with having copied over the files, I can plugin other USB enclosures with different drives and they too are working.
Like you mentioned, it was always possible to use USB devices within my Virtual Machines, so it was clear that the USB ports were functional. I actually got the files from a clean Windows 7 VM, copying out the \windows\inf folder and doing a compare between
the the real one and the virtual one. I found the two missing files you mentioned, along with 8 others. I went ahead and included them all in your fix.
It worked, Amazing. Thanks again. :O) -
I've had Broadband for about 2 months at my current address. I'm having constant disconnections. This is my log entry It seems to be getting worse. I have home hub 4. I've run the line test but to be honest I don't know if there is noise on the line or not.
19:03:40, 26 Oct.
(157839.000000) DSL is up
19:03:38, 26 Oct.
(157837.530000) DSL noise margin: 5.90 dB upstream, 10.70 dB downstream
19:03:37, 26 Oct.
(157836.420000) DSL line rate: 1160 Kbps upstream, 6648 Kbps downstream
19:03:25, 26 Oct.
(157824.020000) CWMP: session closed due to error: Could not resolve host
19:03:25, 26 Oct.
(157824.000000) CWMP: Server URL: https://pbthdm.bt.mo; Connecting as user: ACS username
19:03:25, 26 Oct.
(157823.990000) CWMP: Session start now. Event code(s): '4 VALUE CHANGE'
19:02:54, 26 Oct.
(157793.640000) CWMP: session closed due to error: Could not resolve host
19:02:53, 26 Oct.
(157792.060000) CWMP: Server URL: https://pbthdm.bt.mo Connecting as user: ACS username
19:02:53, 26 Oct.
(157792.050000) CWMP: Session start now. Event code(s): '4 VALUE CHANGE'
19:02:52, 26 Oct.
(157791.700000) CWMP: Initializing transaction for event code 4 VALUE CHANGE
19:02:49, 26 Oct.
(157788.190000) DSL is down after 6 minutes uptime
19:02:49, 26 Oct.
(157788.190000) ETHoA is down after 6 minutes uptime
19:02:49, 26 Oct.
(157787.840000) PPPoA is down after 6 minutes uptime [Waiting for Underlying Connection (WAN DSL - Up)]
19:02:45, 26 Oct.
(157783.870000) PPP LCP Send Termination Request [User request]
Speed test using bt speed tester. I'm guessing there is something seriously wrong here because I think my speed should be at least double that.if there is an extension socket then that is a good reason to conenct to test socket to eliminate any problems caused by the extension.. if you need an engineer visit and the cause of your drop outs is the extension socket then you will get a bill for £129.99 for call out
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.
Maybe you are looking for
-
IDOCs processing - MM or FI invoice - if docum is complete- post else park
Hello, i load xml file into idoc (edi_data_incoming) - in the file are MM and FI invoices. But now i need to process these idocs. If idoc could be posted (idoc has every mandatory data) then post idoc else park document. I need to know how to check
-
New MacBook Retina Pro 15.4 inch with 2.2 Ghz and running Yosemite 10.10.2 will not recognize LaCie Quadra H2 disk. Also will not complete Time Machine Backup onto My Passport for Mac which it does recognize. Plenty of disc space both externals.
-
Moving a Clip From One Project to Another
How do you move a clip from one project to another keeping the sound clip and title that was used on that clip?
-
How does syncing Notes work with Mountain Lion ?
How does syncing Notes with Mountain Lion?
-
Need to reset my DLink 2750B about 3-4 times a day.
Well, It has been a few months since I posted about the same problem here. About 3-4 times a day (almost always when I am online), I lose my internet connection in the entire house. All I have to do is unplug the modem, wait 15 seconds, plug it back