Constant disconnecting with my WRT120N

Hi
I have a problem with my wrt120n. I'm having a constant disconnecting problem.
I don't have any problem with the wireless computers connected to the router but the wired one keep geeting disconnected. I'm loosing the internet many times a day on thiis one. Like I said the wireless is ok.
My old router on my computer ( wired) was working well before I installed the wrt120n.
Can someone help me?
Thank you!

This is a problem of the Linksys/Cisco WRT120N product itself. The team from Cisco/Linksys is very irresponsible. Why i say so ?
The 802.11n signal is not certified to be supported but yet they have included this support in this router. By doing so, it causes this related problem that most consumers must be facing now or in the past. It is a shame that such a big company operates and sell their products this way.
The solution: It does not have anything to do with MTU, beacon interval etc.... Just use Mixed BG wireless signal instead of
Wireless N only when you goes to Manual Setup. I am sure that this solves the problem.

Similar Messages

Constant disconnects with Linksys BEFW11S4/Westell/Bellsouth Ultra DSL

I recently upgraded to the 6mb DSL service from Bellsouth. Previously I had the 3mb. Anyways everything was fine for sometime even with the faster service. The last few weeks I have been having constant disconnects(several a day). Naturally the wireless lite on my Linksys BEFW11S4 goes out each time. I then un-power the router then re-power and I'm off and running again. I am using a westell modem. Bellsouth tells me that its not them since i do have an internet coneection and referred me to Linksys. After several live chats(due to disconnects and then having to start tellin my issue all over again) they had me upgrade my firmware. Well did that and problem hasn't changed. I've played with the different router channels and they don't seem to help as well. Bellsouth told me that I had a static ip, so I tied setting up router that way, but then i got no connection. Unil reently everything was fine, this just started! Any help is greatly appreicated. My 17 yr old daughter is going through internet withdraws upstairs!

If you are on DSL using a Westell Modem; make sure you ask your ISP to bridge the Modem first and use the PPPoE fucntion on your router. Change the LAN IP of the router to something else like 192.168.2.1 so it won't get a conflict with the IP of the Westell. Then if you are on cable, you can try adjusting the MTU size to 1492, 1400, 1300, or 576 then check which value would get your connection stable. You can reset your router right after you upgrade it also, then reconfigure it again. Hopefully yell be fine after that!
"The war between heaven and hell depends on the choices we make, and those choices require sacrifice. That's the test"

Constant disconnects with wireless router.

Hello and thanks in advance for any help you can provide.
I have a WRT54G wireless router with speed booster. I am experiencing constant disconnects when online gaming. I have one PC - running windows vista 64bit ultimate. This computer is running a wireless connection which is secured and is about 10 feet from the router through a wall.
I also have an xbox 360 with a wired connection. It doesnt seem to have the same issues but does become a bit sluggish at times.
I have called linksys and they instructed me on how to upgrade to the latest firmware. I think it is 7.5.0 or something. Still having issues. Cox (my ISP) has been out and says I am getting a constant 2mb download.
Any help would be appreciated. I have talked to linksys again they have me pull up cmd and run a test which shows me at a 4-10% packet loss. They say this is an acceptable rate.
Still the problems continue. If anyone can help I would be very greatful. If you need more info just let me know and I will provide whatever I can. Thanks!!!
Message Edited by madmike6537 on 11-26-2008 03:16 PM

Sounds like a vista problem, they are breading like rabbits it seems. The WRT54G is a good router, I had one for years with no problems. What type of wireless card do you have in the pc, and is it PCI or USB

E71 constant disconnects with bluetooth

My previous post was moved to "troubleshooting tips" but thats not the case, the problem is with the E71 phone itself. The blue ant headset i have works fine with all other phones
It contantly disconnects with the E71 , the problem is the phone. What can we do to fix the phone?

Sounds like a vista problem, they are breading like rabbits it seems. The WRT54G is a good router, I had one for years with no problems. What type of wireless card do you have in the pc, and is it PCI or USB

Constant disconnects with "no PPPoE" and "no valid IP address" errors

I have AT&T DSL and have an Airport Extreme connected to a Speedstream 4100 modem. My Internet connection has been fine for nearly a year with the AEBS but for the past couple weeks has been disconnecting so frequently that it's almost become useless. The problems reported by the AEBS are: PPPoE Server (no PPPoE server found) and Internet Connection (AEBS doesn't have a valid IP address). It's always these two problems reported.
Restarting the AEBS gets me connected again, and sometimes the connection will come back on its own, but only for a short while. I don't know how to troubleshoot this. Help! Here are my AEBS settings:
Radio Mode: Automatic
Radio Channel Selection: Automatic
Wireless Security: WPA2 Personal
Use wide channels: Checked
Create a closed network: Checked
Use interface robustness: Unchecked
Sorry, I'm not a network guy so forgive me if I've omitted some important information. Below the log from a recent bout of connects and disconnects:
Jun 19 10:04:06 Severity:5 Disconnected.
Jun 19 10:04:09 Severity:5 Binding added for udp, 0.0.0.0:32816 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:04:09 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:06:40 Severity:5 Binding added for udp, 0.0.0.0:32817 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:06:40 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:07:37 Severity:6 Parameter updated - drTY.
Jun 19 10:07:37 Severity:5 unloading current configuration.
Jun 19 10:07:47 Severity:5 Connecting via ethernet (user "[email protected]" service "AT&T DSL Connection").
Jun 19 10:07:47 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
Jun 19 10:07:47 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
Jun 19 10:07:47 Severity:5 Rotated CCMP group key.
Jun 19 10:07:47 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:07:52 Severity:5 (WAN) link state is Up.
Jun 19 10:07:57 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:07:57 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:08:02 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:08:04 Severity:5 Associated with station 7c:6d:62:a2:dc:0c
Jun 19 10:08:04 Severity:5 Installed unicast CCMP key for supplicant 7c:6d:62:a2:dc:0c
Jun 19 10:08:06 Severity:5 Connection accepted from [::ffff:10.0.1.2]:61426.
Jun 19 10:08:08 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61428.
Jun 19 10:08:08 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61427.
Jun 19 10:08:13 Severity:5 Associated with station 00:24:36:90:4e:f6
Jun 19 10:08:13 Severity:5 Installed unicast CCMP key for supplicant 00:24:36:90:4e:f6
Jun 19 10:08:17 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:08:18 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:18 Severity:5 Binding added for udp, 0.0.0.0:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:08:19 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:20 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:22 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:26 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:27 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:08:28 Severity:5 Binding added for udp, xxx.xxx.xxx.xxx:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:08:32 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:08:32 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +0 seconds).
Jun 19 10:09:09 Severity:5 Disconnected.
Jun 19 10:11:32 Severity:5 Initialized (firmware 7.4.2).
Jun 19 10:11:34 Severity:5 Connecting via ethernet (user "[email protected]" service "AT&T DSL Connection").
Jun 19 10:11:35 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
Jun 19 10:11:35 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:11:35 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
Jun 19 10:11:35 Severity:5 Rotated CCMP group key.
Jun 19 10:11:35 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:11:39 Severity:5 (WAN) link state is Up.
Jun 19 10:11:45 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:11:45 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:11:45 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:11:50 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +5 seconds).
Jun 19 10:11:50 Severity:5 Associated with station 7c:6d:62:a2:dc:0c
Jun 19 10:11:50 Severity:5 Installed unicast CCMP key for supplicant 7c:6d:62:a2:dc:0c
Jun 19 10:11:52 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61481.
Jun 19 10:11:53 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61483.
Jun 19 10:11:54 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61484.
Jun 19 10:11:55 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:11:55 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:12:02 Severity:5 Associated with station 00:24:36:90:4e:f6
Jun 19 10:12:02 Severity:5 Installed unicast CCMP key for supplicant 00:24:36:90:4e:f6
Jun 19 10:12:08 Severity:7 Public address reported as xxx.xxx.xxx.xxx to 10.0.1.4:5353
Jun 19 10:12:08 Severity:5 Binding added for udp, xxx.xxx.xxx.xxx:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:12:08 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:12:25 Severity:5 Disconnected.
Jun 19 10:17:00 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:17:10 Severity:5 Disconnected.
Jun 19 10:17:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:17:49 Severity:5 Binding added for udp, 0.0.0.0:32770 to 10.0.1.4:5353 with lifetime 7200
Message was edited by: DakotaPaul

This is what the log has looked like for the past several hours.
Jun 19 17:37:49 Severity:5 Binding added for udp, 0.0.0.0:32851 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:37:50 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:57 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:05 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:21 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:39:04 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:43:48 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:48 Severity:5 Binding added for udp, 0.0.0.0:32852 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:43:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:55 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:03 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:19 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:45:03 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:49:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:49 Severity:5 Binding added for udp, 0.0.0.0:32853 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:49:50 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:57 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:05 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:21 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:51:04 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:54:46 Severity:5 Rotated CCMP group key.
Jun 19 17:57:01 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:57:01 Severity:5 Binding added for udp, 0.0.0.0:32854 to 10.0.1.4:5353 with lifetime 7200
Thanks for any help you can provide. I'm about to throw the modem and/or router out the window!

Constant disconnecting with HomeHub1

I've recently started having problems with my BT HomeHub1 and i'm stumped on what to do with this.
All devices connected to the homehub are thrown off in random intervals at the same time, and the broadband connection drops out of the list of wireless networks available in the area. But the lights on the hub remain the same, saying that it is still connected to the internet.
When I reset the homehub and let it load, it connects but then disconnects again and this problem repeats between 10 minutes to an hour.
There are no problems in my area when I checked the site
I tried the quiet line test and i've heard no crackling noise.
I tried finding that ADSL Line Status for homehub1 but there is no guide to get to that screen.
If anybody could help guide me into how to sort this out I would greatly appreciate it. Thanks.

Its most likely a fault with the HH1 or its power unit. I have a HH1 and am on my second power unit.
This guide will tell you how to get to the ADSL stats ADSL Statistics
Or for a direct link, use this BT Home Hub 1 - DSL Connection
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Constant disconnect with centurytel and wrt54gs

I set up dsl for my parents with centurytel, and linksys wireless router.
they can get online fine but seems like while they are surfing it constantly drops the internet connection. if you go to 192.168.1.1 it shows disconected and you have to either wait for it to reconnect or just hit the connect button.
I have it set up with auto dhcp and the router is set to 192.168.2.1 I have centurytel at my house and work with no problems what so ever, any ideas to remidy this?
I have gotten router update already, checked to make sure all the dsl filters are on all the phone lines. rechecked all the settings, reset both modem and router and started from scratch ect ect. is there something Im missing.
Thanks, John

Connect a computer straight to the modem and check for a static connection...If that does not diconnect you, download the firmware for your router from here , re-connect your modem==>router==>computer...
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...
Then, unplug the power keep holding down the reset button for another 30 Seconds...
Plug the power back in, and keep holding down the reset button for 30 Seconds...
Release the reset button...Click here and follow the link to re-configure your router...Connection should be fine...

Constant disconnects with flashing DSL light

Hi, my Infinity 2 connection has been unusable since last Friday 8th Feb. I get at the most a few minutes of up time then the connection drops with a flashing DSL light on the Openreach Modem.
I have tried power cycling the hub and modem, changed the cable to the socket and also relocated the modem.
I logged the call with BT on the 9th and on the 11th they marked the job as fixed, but it isnt.
This situation is very frustrating as I rely on my connection heavily for home and vpn to work but there seems to be no progress in a resolve.

I phoned the helpline in the end and the guy the other end actually did a line test and found an issue. Apparently an engineer is booked but cannot come out until 21st Feb!!! That will be nearly 2 weeks downtime. I have not had the appointment in confirmed in black or white which is not reassuring either.
Really annoyed as when I had adsl with 02 any issue (which was very rare) got resolved either next day or within the promised 3 days.
I also didn't have to chase them to resolve it and they Defo didn't mark a job as fixed until it actually was.
Not very impressed by BT at all. I have phone, Bt Vision and Infinity 2 with them so I pay them enough every month.

I have a 1TB WD external hard disk, which suddenly cannot be detected in my system. When i connect the hardisk to the macbook, the disk appears and immediately disconnects with the message "Disk not properly ejected". Any advice ?

I have a 1TB WD external hard disk, which suddenly cannot be detected in my system. When i connect the hardisk to the macbook, the disk appears and immediately disconnects with the message "Disk not properly ejected". Any advice ?

verify on another Mac if the same
WD is having issues with mavericks as you can see on the WD forum, did you install any WD software (never do that) when you connected the drive for the first time?
possible issue is a dead SATA bridge card or the new WD firmware w/ Mavericks.
SATA card issue
Your dead external hard drive is likely fine! Great hope for your 'faulty' external HD
http://community.wd.com/t5/External-Drives-for-Mac/bd-p/passport_mac
verify on another Mac if all possible

CVP 7.0.2 Abnormally disconnected with error code 38

Hi all,
We have an issue where when called from outbound, it is not possible to reach a certain number. It doesn't even play the dial tone. isdn debug is as follows :
Feb 15 17:51:01.830: ISDN Se0/2/0:15 Q931: TX -> RELEASE pd = 8 callref = 0xE97B
Feb 15 17:51:01.846: ISDN Se0/2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x697B
Feb 15 17:51:05.050: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x697D
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98385
                Exclusive, Channel 5
        Progress Ind i = 0x8083 - Origination address is non-ISDN
        Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info
        Calling Party Number i = 0x0081, '02124783464'
                Plan:Unknown, Type:Unknown
        Called Party Number i = 0xC1, '2751920'
                Plan:ISDN, Type:Subscriber(local)
Feb 15 17:51:05.062: ISDN Se0/2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xE97D
        Channel ID i = 0xA98385
                Exclusive, Channel 5
Feb 15 17:51:05.066: %HTTPC-6-REQUEST_FAILED: request URI http://ipphone.fw.garanti.com.tr/ipphone/musteribilgiler?source=TLC&call_data=002124783464-800321200 failed
Feb 15 17:51:05.066: %IVR-3-APP_ERR: Musteri bilgileri serverdan alinamadi - Hata Kodu: error
Feb 15 17:51:05.210: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
Feb 15 17:51:05.226: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
Feb 15 17:51:05.230: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
Feb 15 17:51:05.238: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
Feb 15 17:51:05.246: %IVR-3-APP_ERR:
**** CVP HANDOFF.TCL: 57080581.76BE11E2.A32B001B.D5293620 abnormally disconnected with code 38. ****
Feb 15 17:51:05.258: ISDN Se0/2/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xE97D
Feb 15 17:51:05.290: ISDN Se0/2/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x697D
Feb 15 17:51:05.294: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to 02124783464 N/A
Feb 15 17:51:07.274: %IVR-3-APP_ERR: ani: 002124783464 dnis: 800321200 | ev_setup_done ls_000 | ev_disconnected di_016 |
Feb 15 17:51:07.298: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to 02124783464 N/A
Feb 15 17:51:07.298: %ISDN-6-DISCONNECT: Interface Serial0/2/0:4 disconnected from 02124783464 , call lasted 2 seconds
Feb 15 17:51:07.302: ISDN Se0/2/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xE97D
        Cause i = 0x8090 - Normal call clearing
Feb 15 17:51:07.362: ISDN Se0/2/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x697D
Feb 15 17:51:07.366: ISDN Se0/2/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xE97D
Feb 15 17:51:08.702: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x697E
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98391
                Exclusive, Channel 17
        Calling Party Number i = 0x0083, '05336805920'
                Plan:Unknown, Type:Unknown
        Called Party Number i = 0xC1, '2751935'
                Plan:ISDN, Type:Subscriber(local)
Feb 15 17:51:08.714: ISDN Se0/2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xE97E
        Channel ID i = 0xA98391
                Exclusive, Channel 17
Feb 15 17:51:08.718: %HTTPC-6-REQUEST_FAILED: request URI http://ipphone.fw.garanti.com.tr/ipphone/musteribilgiler?source=TLC&call_data=005336805920-800321925 failed
Feb 15 17:51:08.718: %IVR-3-APP_ERR: Musteri bilgileri serverdan alinamadi - Hata Kodu: error
Feb 15 17:51:08.798: ISDN Se0/2/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xE97E

Dear
Code 38 Indicates that the network is not functioning correctly and that the condition is likely to last
for an extended period.
to me the GW is not able to make SIP connection and is likely due to incorrect
IP Address is seen from the GW.I hope to share the configuration.
Thank you
please rate , if this will help

My ipod nano has come up with ok to disconnect with a tick and has frozen. Can anyone tell me what I need to do please.

Can anyone help with a screen that says ok to disconnect with a tick on the front? The ipod has frozen and I can't do anything!

Try a hard reset as described in this article.
How to reset iPod
B-rock

After converting my vid to constant rate with Handbreak, Premire Elements 11 gets choppy

I am using my cell phone SGH-T599 to shoot video. In order for me to edit it I have to convert it from variable rate to constant rate with Handbreak, otherwise the video and sound go out of sync. But apparently there is something wrong with the conversion settings because when I start to edit it doesn't run smoothly, the indicator bar skips and gets stuck. For example, I can not simply move the bar forward to speed up ahead. This makes editing extremely difficult specially if I want to make a cut in the middle of a sentence etc. Is there a way of fixing this, perhaps lowering the frame rate? I I've included a snapshot of both Handbreak and MediaInfo.

elpepin
When you are doing your HandBrake variable to constant frame rate, use the H.264 (x264) Video codec under the Video Tab.
I typically replace "Chapters" with seconds.
Container = Mp4
Leave the Picture Tab as is.
Head for the Video Tab.
Video Codec = H.264 (x264)
Dot the Constant
Dot the Constant Quality leave at 20 RF
Uncheck web optimize
Leave Presets at Regular/Normal
Leave the Audio Tab as is.
Guideline for now is to make only the changes necessary - change a variable frame rate to a constant one.
By the way, why are you using a HandBrake Average Bitrate = 1500 kbps (kilobits per second) when the source is 12 Mbps (megabits per second)?
Hit the Start Button at the top left of the workspace, and wait for the "Queue Finished" in the progress bar at the bottom left of the workspace.
Have you done that?
Please give it a try and then let us know the results.
Thanks.
ATR

FS[3988]: Possible network disconnect with primary database

Hi All,
In the standby database alert log I'm getting the below error:
Thu Feb 10 11:09:10 2011
RFS[3971]: Possible network disconnect with primary database
Thu Feb 10 11:10:11 2011
RFS[3976]: Possible network disconnect with primary database
Thu Feb 10 11:11:12 2011
RFS[3979]: Possible network disconnect with primary database
Thu Feb 10 11:12:13 2011
RFS[3982]: Possible network disconnect with primary database
Thu Feb 10 11:13:15 2011
RFS[3985]: Possible network disconnect with primary database
There is no error in the primary database regarding this.
And after this no archive logs are being pushed to the standby database.
In V$ARCHIVE_DEST_STATUS view the column synchronizaion_status says CHECK NETWORK for dest_name LOG_ARCHIVE_DEST_2
Please advice.
Thanks.
Regards,
Ashwani N.

Both messages look crystal clear to me.
Did you check the network?
If not, why not?
Your posting history here is a bit appalling
823436
     Newbie
Handle:      823436
Status Level:      Newbie
Registered:      Dec 24, 2010
Total Posts:      28
Total Questions:      9 (7 unresolved)
Sybrand Bakker
Senior Oracle DBA

Calls Getting disconnected with reason code 26

Hi,
Few of my calls are getting disconnected with reason code 26. on agent screen it just flash and disconnect.as per RCD its showing Error code 0( fine) and finally its ending at Skill Group Node. talk time is 1 or 2 seconds. agents having auto answer setting as well as IP Phone set auto ans with headset.
my setup is IPIVR based UCCE setup.
Please help
Regards-
PK

Hi PK,
CD 26 normally indicates Resource Not available in CUCM side. please check the Jtapi gateway process logs for the failed calls. you should be able to see something similar to below
19:08:37:896 PG1A-jgw1 Trace: ConnFailedEv CID: 27224748 Addr: 80002985 CiscoCause: CAUSE_RESOURCESNAVAIL Cause: CAUSE_RESOURCES_NOT_AVAILABLE.
if that is the case , please check from CUCM perspective as well.
Regards,
Sasikumar.

Constant problems with Java since upgrade to OS X 10.7

I recently purchased a Macbook Air with OS X 10.7 installed, now updated to version 10.7.5.
I'm having constant issues with Java and repeatedly being told to update to the latest version, even when I have the latest version installed (now Java 7 update 9). I've visited dozens of forums and seen posts about the same issue, but none of the solutions work for me.
I've seen variations of the following advice in several places:
Apple disables the Java plug-in and Webstart applications when the Java update is done using Software Update. Also, if the Java plug-in detects that no applets have been run for an extended period of time it will again disable the Java plug-in.
To enable the Java plug-in
Go to Finder > Applications > Utilities > Java Preferences.
In the Java Preferences window check the box for Enable Applet plug-in and Webstart applications.
But I can't find anything called "Java Preferences" in my Utilities folder. I found a Java control panel in my System preferences, and it tells me everything is OK and running.
I also see comments about emptying the cache (Java cache?), but can't find where it's kept. I also can't find where the Java plugins are stored. So what to do?
Thanks for any assistance.
Martha

I went to the link on the Support website, downloaded the Java from there (Java for OS X 2012-006) and installed it. Then I went to the Java control panel in System prefs and the information is exactly the same as it was before I installed Java version 6. It still says I have the recommended version of Java (Java 7 update 9), which is what I installed a few hours ago.
Then I went back to the website where I've been having problems today and went through the process of requesting a document from the Spanish tax authorities, which I've never had trouble with in the past (before Lion). I got the same results as earlier and the same page sending me to www.java.com to "download the latest version". So I'm back to square one.
There's a comment on the page your link sent me to that mentions the "Missing plug-in" region on some web pages, but I've never seen this anywhere. All I ever get is a message telling me to update my Java.
Is there another version of Java that would work better? If so, where can I get it?
Thanks.

Constant disconnecting with my WRT120N

Similar Messages

Maybe you are looking for