Constant disconnects with flashing DSL light

Hi, my Infinity 2 connection has been unusable since last Friday 8th Feb. I get at the most a few minutes of up time then the connection drops with a flashing DSL light on the Openreach Modem.
I have tried power cycling the hub and modem, changed the cable to the socket and also relocated the modem.
I logged the call with BT on the 9th and on the 11th they marked the job as fixed, but it isnt.
This situation is very frustrating as I rely on my connection heavily for home and vpn to work but there seems to be no progress in a resolve.

I phoned the helpline in the end and the guy the other end actually did a line test and found an issue. Apparently an engineer is booked but cannot come out until 21st Feb!!! That will be nearly 2 weeks downtime. I have not had the appointment in confirmed in black or white which is not reassuring either.
Really annoyed as when I had adsl with 02 any issue (which was very rare) got resolved either next day or within the promised 3 days.
I also didn't have to chase them to resolve it and they Defo didn't mark a job as fixed until it actually was.
Not very impressed by BT at all. I have phone, Bt Vision and Infinity 2 with them so I pay them enough every month.

Similar Messages

Flashing DSL light and no internet since yesterday

I've been remarkably pleased with my BT broadband since it was installed a while back, a few hiccups with slow speeds very occasionally but on the whole very happy. Someone did warn me that I'd be very happy until I had a problem and then I would go crazy again, but am trying to avoid that!
Basically, when I left my house for work yesterday my broadband was working fine, when I got in yesterday evening I had a flashing DSL light which I've had ever since, and am trying to make do with the meagre allowance I have left on my phone and using 3G hotspot for now for urgent internet related stuff,
I've tried the BT fault finder, which says there is no network fault, and tried the broadband troubleshooter, which basically said I wasn't using a BT Home Hub so would I like to pay through the nose for a BT expert... I'm thinking there must be some communication down the line for it to be able to tell I'm not using a Home Hub?
I'm using a netgear wireless router. I've rebooted it, still get flashing light. Have switched off and left for 10 minutes in case of some kind of overheat - still get flashing light. Have checked wires and cables all firmly connected.
What are my next steps, I'm trying to avoid helpline hell until I've exhausted any other reasonable options.
Is a router likely to suddenly go wrong, or is it more likely a BT fault?
Thanks.

have you tried connecting to test socket with a new filter to see it that helps?
as phone works try quiet line test dial 17070 option 2 should be quiet and best with corded phone
anything here for your exchnage http://usertools.plus.net/exchanges/mso.php
http://usertools.plus.net/exchanges/?
http://btbusiness.custhelp.com/app/service_status
http://bt.custhelp.com/app/answers/detail/a_id/15036
http://community.plus.net/exchange-information/
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Constant disconnects with Linksys BEFW11S4/Westell/Bellsouth Ultra DSL

I recently upgraded to the 6mb DSL service from Bellsouth. Previously I had the 3mb. Anyways everything was fine for sometime even with the faster service. The last few weeks I have been having constant disconnects(several a day). Naturally the wireless lite on my Linksys BEFW11S4 goes out each time. I then un-power the router then re-power and I'm off and running again. I am using a westell modem. Bellsouth tells me that its not them since i do have an internet coneection and referred me to Linksys. After several live chats(due to disconnects and then having to start tellin my issue all over again) they had me upgrade my firmware. Well did that and problem hasn't changed. I've played with the different router channels and they don't seem to help as well. Bellsouth told me that I had a static ip, so I tied setting up router that way, but then i got no connection. Unil reently everything was fine, this just started! Any help is greatly appreicated. My 17 yr old daughter is going through internet withdraws upstairs!

If you are on DSL using a Westell Modem; make sure you ask your ISP to bridge the Modem first and use the PPPoE fucntion on your router. Change the LAN IP of the router to something else like 192.168.2.1 so it won't get a conflict with the IP of the Westell. Then if you are on cable, you can try adjusting the MTU size to 1492, 1400, 1300, or 576 then check which value would get your connection stable. You can reset your router right after you upgrade it also, then reconfigure it again. Hopefully yell be fine after that!
"The war between heaven and hell depends on the choices we make, and those choices require sacrifice. That's the test"

Help with flashing green light on Express

I am trying to set up an airport express in my office to use with my a windows laptop and my iPhone. I had it working yesterday and took it home to set up a home profile on it. Everything was working fine in both places. Today when I plugged it in it went to a steady green for a second or two then amber while it booted as usual but then to a rapid flashing green. I tried everything I can think of including resets and it still does the same thing. It keeps flashing green and never appears in my network lists. Any ideas?

The rapid flashing green light has happened 3 times to me since I first set up my Airport Extreme in fall 2007. The problem is always fixed by unplugging the LAN cable that connects through my hardwire network to my Airport Express. If I plug the LAN cable back, the rapid green returns and I can't access the network. Unplug it, and voila, the network is back. (I only encounter the problem when I have unplugged the Extreme and plugged it back in - if I leave it alone it is fine).
I think the problem is a conflict in my Airport Express being set to act as a wireless bridge by my computer-tech friend, but I had it set up to be hardwired in the network so as to never lose my iTunes to hi-fi connection if there was a wireless problem. I've yet to sit down to resolve the Express issue; however, I suspect that if your case is similar, the Extreme is in conflict with another network device. If you can isolate it the network to just your Internet connection and Extreme, see if that solves it.
Good luck.

Constant disconnects with wireless router.

Hello and thanks in advance for any help you can provide.
I have a WRT54G wireless router with speed booster. I am experiencing constant disconnects when online gaming. I have one PC - running windows vista 64bit ultimate. This computer is running a wireless connection which is secured and is about 10 feet from the router through a wall.
I also have an xbox 360 with a wired connection. It doesnt seem to have the same issues but does become a bit sluggish at times.
I have called linksys and they instructed me on how to upgrade to the latest firmware. I think it is 7.5.0 or something. Still having issues. Cox (my ISP) has been out and says I am getting a constant 2mb download.
Any help would be appreciated. I have talked to linksys again they have me pull up cmd and run a test which shows me at a 4-10% packet loss. They say this is an acceptable rate.
Still the problems continue. If anyone can help I would be very greatful. If you need more info just let me know and I will provide whatever I can. Thanks!!!
Message Edited by madmike6537 on 11-26-2008 03:16 PM

Sounds like a vista problem, they are breading like rabbits it seems. The WRT54G is a good router, I had one for years with no problems. What type of wireless card do you have in the pc, and is it PCI or USB

Constant disconnecting with my WRT120N

Hi
I have a problem with my wrt120n. I'm having a constant disconnecting problem.
I don't have any problem with the wireless computers connected to the router but the wired one keep geeting disconnected. I'm loosing the internet many times a day on thiis one. Like I said the wireless is ok.
My old router on my computer ( wired) was working well before I installed the wrt120n.
Can someone help me?
Thank you!

This is a problem of the Linksys/Cisco WRT120N product itself. The team from Cisco/Linksys is very irresponsible. Why i say so ?
The 802.11n signal is not certified to be supported but yet they have included this support in this router. By doing so, it causes this related problem that most consumers must be facing now or in the past. It is a shame that such a big company operates and sell their products this way.
The solution: It does not have anything to do with MTU, beacon interval etc.... Just use Mixed BG wireless signal instead of
Wireless N only when you goes to Manual Setup. I am sure that this solves the problem.

Constant crashing with Flash CC in Windows 8.1

Hello I am an avid Flash user who has worked in the program for roughly 10 years since before it was bought by Adobe and called Macromedia MX5. This most recent version of Flash CC is incredibly buggy with respect to the following areas..
I am constantly suffering crashes in Flash on my windows 8.1 desktop computer. The tower I have is more than capable to handle Flash CC so I don't understand why it is crashing. This isn't happening with even heavier hitting software such as After Effects only Flash CC.
I especially notice crashes and stalling when saving as well as when scrubbing or playing in the timeline or trying to clear key frames or adjust keyframes in any manner.
Additionally I have noticed more substantial problems and flaws with Flash CC in comparison to previous versions. This is evident most in the audio options. I think a lot of the problems that stem from audio playback and lagging playback time is the fact that audio is defaulting to a repeat function of 1x when it should default to no repeat function. Sometimes changing repeat to 0 resolves this issue but even still audio always seems to start from beginning of the clip/sound file as opposed to playhead despite having stream selected. This was never a probelm in previous versions of Flash for me, EVER. I don't understand how this has become a problem now all of a sudden when this version of Flash is supposed to be running 64bit as opposed to 32bit.
I also noticed that the audio on some files has ceased to work when I revisit the file later on. It will not play no matter what in the stage/timeline but is audible when I do a test movie or export movie.
Is anyone else having similar issues here? I didn't seem to have so many problems when I was using Flash CS6, this audio thing is probably my biggest beef though I can't say I'm too fond of the crashing either.

first try resetting your preferences by holding down shift-ctrl-alt while starting flash pro. you'll see a confirmation dialog if done correctly.
if that fails, uninstall and then reinstall flash pro.
if that fails, uninstall, clean and then reinstall flash pro following these steps exactly, http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

E71 constant disconnects with bluetooth

My previous post was moved to "troubleshooting tips" but thats not the case, the problem is with the E71 phone itself. The blue ant headset i have works fine with all other phones
It contantly disconnects with the E71 , the problem is the phone. What can we do to fix the phone?

Sounds like a vista problem, they are breading like rabbits it seems. The WRT54G is a good router, I had one for years with no problems. What type of wireless card do you have in the pc, and is it PCI or USB

Constant disconnecting with HomeHub1

I've recently started having problems with my BT HomeHub1 and i'm stumped on what to do with this.
All devices connected to the homehub are thrown off in random intervals at the same time, and the broadband connection drops out of the list of wireless networks available in the area. But the lights on the hub remain the same, saying that it is still connected to the internet.
When I reset the homehub and let it load, it connects but then disconnects again and this problem repeats between 10 minutes to an hour.
There are no problems in my area when I checked the site
I tried the quiet line test and i've heard no crackling noise.
I tried finding that ADSL Line Status for homehub1 but there is no guide to get to that screen.
If anybody could help guide me into how to sort this out I would greatly appreciate it. Thanks.

Its most likely a fault with the HH1 or its power unit. I have a HH1 and am on my second power unit.
This guide will tell you how to get to the ADSL stats ADSL Statistics
Or for a direct link, use this BT Home Hub 1 - DSL Connection
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

My network, based on modem, wifi router (Airport Extreme),Time Capsule and Airport Express simply disconnects with all the lights green on the modem and Extreme, but the other components offline, 5 or so times per day. I suspect the Extreme.

I have a Cisco System3 modem, feeding an Airport Extreme, which connects wirelessly a Timecapsules and an Airport Express both of which extend the network, ie send out more WiFi signal. The system worked well for a long time, say a year and a half and then it started dropping out. All the lights on the modem and airport Extreme stay green, but the other two components are blinking yellow. I've tried limiting the channels, but there are few sources in my neighborhood. I have tried resetting the Extreme which worked for a week and now it's back to its random disconnect behavior. I have read some of these blogs and no one seems to know what to do, especially not Apple. Do I just get another router or what? What do I lose if I use a non Apple router and what would you suggest?

Welcome to the discussion area, Junkcanoe!
I don't have a setup like yours, but might be able to offer some assistance.
Basically I have two jacks, a TC and an AE and I'd like to create a roaming network. Both of them are set to bridge mode with the same SSID, WPA2 security, same password, etc.
This would be the normal way to set up a roaming network, but the wild card here is that we don't know anything about how the main router that supplies the ethernet connections (valid IP addresses) to the condos might be configured.
For example, most apartments, hotels, etc that provide ethernet jacks usually limit the number of devices that can connect to each jack. Hotels tend to limit this to one or two devices. I counted six devices that you say will work properly plus a few more. Since you have two separate ethernet jacks, you may be looking at a situation where each jack is allocated a total of 4 devices, or valid IP addresses.
The bottom line here is that we won't be able to make much progress until we know more how the main router there has been configured. Is it possible for you to ask the complex manager (who will probably need to ask the IT guy) how many devices are allowed to connect per ethernet jack? Another way to ask the same question is how may valid IP addresses will each ethernet jack allow?
If you can, could I ask you to perform an experiment? Rather than have both the AirPort Extreme and Time Capsule each connect to a separate ethernet jack, can you temporarily move one device near the other and connect them together using an ethernet cable? (Or, use a long ethernet cable if you don't want to move either device) LAN <-> port on one to LAN <-> port on the other. In other words, you'll only be using one of the ethernet ports in the condo for this experiment.
Any difference in performance or number of devices allowed to connect?
Message was edited by: Bob Timmons

Constant disconnects with "no PPPoE" and "no valid IP address" errors

I have AT&T DSL and have an Airport Extreme connected to a Speedstream 4100 modem. My Internet connection has been fine for nearly a year with the AEBS but for the past couple weeks has been disconnecting so frequently that it's almost become useless. The problems reported by the AEBS are: PPPoE Server (no PPPoE server found) and Internet Connection (AEBS doesn't have a valid IP address). It's always these two problems reported.
Restarting the AEBS gets me connected again, and sometimes the connection will come back on its own, but only for a short while. I don't know how to troubleshoot this. Help! Here are my AEBS settings:
Radio Mode: Automatic
Radio Channel Selection: Automatic
Wireless Security: WPA2 Personal
Use wide channels: Checked
Create a closed network: Checked
Use interface robustness: Unchecked
Sorry, I'm not a network guy so forgive me if I've omitted some important information. Below the log from a recent bout of connects and disconnects:
Jun 19 10:04:06 Severity:5 Disconnected.
Jun 19 10:04:09 Severity:5 Binding added for udp, 0.0.0.0:32816 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:04:09 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:06:40 Severity:5 Binding added for udp, 0.0.0.0:32817 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:06:40 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:07:37 Severity:6 Parameter updated - drTY.
Jun 19 10:07:37 Severity:5 unloading current configuration.
Jun 19 10:07:47 Severity:5 Connecting via ethernet (user "[email protected]" service "AT&T DSL Connection").
Jun 19 10:07:47 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
Jun 19 10:07:47 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
Jun 19 10:07:47 Severity:5 Rotated CCMP group key.
Jun 19 10:07:47 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:07:52 Severity:5 (WAN) link state is Up.
Jun 19 10:07:57 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:07:57 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:08:02 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:08:04 Severity:5 Associated with station 7c:6d:62:a2:dc:0c
Jun 19 10:08:04 Severity:5 Installed unicast CCMP key for supplicant 7c:6d:62:a2:dc:0c
Jun 19 10:08:06 Severity:5 Connection accepted from [::ffff:10.0.1.2]:61426.
Jun 19 10:08:08 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61428.
Jun 19 10:08:08 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61427.
Jun 19 10:08:13 Severity:5 Associated with station 00:24:36:90:4e:f6
Jun 19 10:08:13 Severity:5 Installed unicast CCMP key for supplicant 00:24:36:90:4e:f6
Jun 19 10:08:17 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:08:18 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:18 Severity:5 Binding added for udp, 0.0.0.0:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:08:19 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:20 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:22 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:26 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:27 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:08:28 Severity:5 Binding added for udp, xxx.xxx.xxx.xxx:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:08:32 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:08:32 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +0 seconds).
Jun 19 10:09:09 Severity:5 Disconnected.
Jun 19 10:11:32 Severity:5 Initialized (firmware 7.4.2).
Jun 19 10:11:34 Severity:5 Connecting via ethernet (user "[email protected]" service "AT&T DSL Connection").
Jun 19 10:11:35 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
Jun 19 10:11:35 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:11:35 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
Jun 19 10:11:35 Severity:5 Rotated CCMP group key.
Jun 19 10:11:35 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:11:39 Severity:5 (WAN) link state is Up.
Jun 19 10:11:45 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:11:45 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:11:45 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:11:50 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +5 seconds).
Jun 19 10:11:50 Severity:5 Associated with station 7c:6d:62:a2:dc:0c
Jun 19 10:11:50 Severity:5 Installed unicast CCMP key for supplicant 7c:6d:62:a2:dc:0c
Jun 19 10:11:52 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61481.
Jun 19 10:11:53 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61483.
Jun 19 10:11:54 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61484.
Jun 19 10:11:55 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:11:55 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:12:02 Severity:5 Associated with station 00:24:36:90:4e:f6
Jun 19 10:12:02 Severity:5 Installed unicast CCMP key for supplicant 00:24:36:90:4e:f6
Jun 19 10:12:08 Severity:7 Public address reported as xxx.xxx.xxx.xxx to 10.0.1.4:5353
Jun 19 10:12:08 Severity:5 Binding added for udp, xxx.xxx.xxx.xxx:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:12:08 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:12:25 Severity:5 Disconnected.
Jun 19 10:17:00 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:17:10 Severity:5 Disconnected.
Jun 19 10:17:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:17:49 Severity:5 Binding added for udp, 0.0.0.0:32770 to 10.0.1.4:5353 with lifetime 7200
Message was edited by: DakotaPaul

This is what the log has looked like for the past several hours.
Jun 19 17:37:49 Severity:5 Binding added for udp, 0.0.0.0:32851 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:37:50 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:57 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:05 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:21 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:39:04 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:43:48 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:48 Severity:5 Binding added for udp, 0.0.0.0:32852 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:43:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:55 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:03 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:19 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:45:03 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:49:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:49 Severity:5 Binding added for udp, 0.0.0.0:32853 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:49:50 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:57 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:05 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:21 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:51:04 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:54:46 Severity:5 Rotated CCMP group key.
Jun 19 17:57:01 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:57:01 Severity:5 Binding added for udp, 0.0.0.0:32854 to 10.0.1.4:5353 with lifetime 7200
Thanks for any help you can provide. I'm about to throw the modem and/or router out the window!

Constant disconnect with centurytel and wrt54gs

I set up dsl for my parents with centurytel, and linksys wireless router.
they can get online fine but seems like while they are surfing it constantly drops the internet connection. if you go to 192.168.1.1 it shows disconected and you have to either wait for it to reconnect or just hit the connect button.
I have it set up with auto dhcp and the router is set to 192.168.2.1 I have centurytel at my house and work with no problems what so ever, any ideas to remidy this?
I have gotten router update already, checked to make sure all the dsl filters are on all the phone lines. rechecked all the settings, reset both modem and router and started from scratch ect ect. is there something Im missing.
Thanks, John

Connect a computer straight to the modem and check for a static connection...If that does not diconnect you, download the firmware for your router from here , re-connect your modem==>router==>computer...
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...
Then, unplug the power keep holding down the reset button for another 30 Seconds...
Plug the power back in, and keep holding down the reset button for 30 Seconds...
Release the reset button...Click here and follow the link to re-configure your router...Connection should be fine...

Another one with flashing amber light on airport express...

New out the box airport express flashing amber...for first 30 seconds after plugin it holds amber steady then starts flashing...
Internet connection fine...using wireless for this iPad... have sky router/modem....sky hd + box connected to router via Ethernet...
Express situated approx 1m from router nothing blocking path...even placed side by side doesn't work...
Airport utility app says device not found...
Did try connecting express to router via Ethernet cable used with sky box but didn't work either...
Any ideas...would a reset be worth a try?
My sky tv is down because of problem with dish on roof...but because my wifi is working I don't see this being connected? Adsl for broadband and satellite for tv...

(running commentary)
Well that wasn't quite right...so will post for anyone who might find of value in future...
The express can be connected to speakers on the same wifi network that the ISP router provides, enabling simultaneous wifi net browsing on my iPad and wifi music through speakers via AirPlay etc....turns out that the method involved includes extending the existing wifi network, so if you want to buy an airport express v2 for primarily network extension, you do not need to connect it to to the ISP router via Ethernet to achieve this...I have done this at the same time as achieving my main aim of using with speakers...so that's def a bonus...and the same goes for each new express and speaker combo you set up around your house/mansion etc...

Constant Problems with flash, Please help Urgent for University work

Hello Im having problems, my 1st frame code is
stop();
import flash.events.MouseEvent;
sync_btn.addEventListener(MouseEvent.CLICK, onClick);
function onClick (e:MouseEvent):void{
gotoAndStop(2);
This seems to work fine, and get my to the 2nd frame, which is where i have problems, my aim is to make a button to continue, and a button to go back to the first frame i p much copied what you used.
stop();
SyncMusic_btn.addEventListener(MouseEvent.MOUSE_DOWN, mouseDownHandler1);
function mouseDownHandler1(event:MouseEvent):void {
gotoAndStop(3);
BktoConfig_btn.addEventListener(MouseEvent.MOUSE_DOWN, mouseDownHandler2);
function mouseDownHandler2(event:MouseEvent):void {
gotoAndStop(1);
The instance names were copied straight from where i named them so they are right, this is making me mad because ive been working on cs5.5 at uni, and on cs4 at home and my cs4 doesnt run my cs5.5 work i had made a start on (where all this was working)
I keep getting the error :
TypeError: Error #1009: Cannot access a property or method of a null object reference.
at Untitled_fla::MainTimeline/frame2()
at flash.display::MovieClip/gotoAndStop()
at Untitled_fla::MainTimeline/onClick()
And the button going back doesnt work, Im in urgent need of help because this assignment is due next week, and ive been working on it for at least 2 weeks now and nothing i can do seems to be working.

The 1009 error indicates that one of the objects being targeted by your code is out of scope. This could mean that the object....
- is not in the display list
- doesn't have an instance name (or the instance name is mispelled)
- does not exist in the frame where that code is trying to talk to it
- is animated into place but is not assigned instance names in every keyframe for it
- is one of two or more consecutive keyframes of the same objects with no name assigned in the preceding frame(s).
If you go into your Publish Settings Flash section and select the option to Permit debugging, your error message should have a line number following the frame number which will help you isolate which object is involved.

Flashing red Light on Photosmart D5160

I have a 3-4 year old Photosmart which know suddenly comes with flashing red light when i try to print.
In the display it says ERR and there are two commas or something on the bottom right. It does not match any of the problems which i can find on hp's pages.
I received an error message on my computer when trying to print - saying something like : do not recognize usb (code 043) Port_#003 Hub_#0003.
Can anyone help me out?
espen

Hi,
Flashing amber LED does not always point to fault. Please see this bug related to system
LED flashing amber.
CSCsh44884 Bug Details : Appliance: No Troubleshooting for System health LED
Status: NEW
Symptom: The appliance hardware has a "System health LED" that may go into amber status,
to indicate a hardware warning, and red to indicate a hardware failure.
Conditions:
In most situation the ACS appliance is still operative, when the light is in amber status.
The appliance should offer better information on what condition caused this alarm, and include this either by new CLI command, or included as additional information in pakage.cab file.
.Workaround:
-Reload appliance
-Verify enviromental conditions (temperature, power)
Alternate Details:
Symptom:
The appliance hardware has a "System health LED" that may go into amber status, to
indicate a hardware warning, and red to indicate a hardware failure
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&b
ugId=CSCsh44884
Let me know if you have any question.
Regards,
~JG
Do rate helpful posts

Constant disconnects with flashing DSL light

Similar Messages

Maybe you are looking for