Constant disconnects with "no PPPoE" and "no valid IP address" errors
I have AT&T DSL and have an Airport Extreme connected to a Speedstream 4100 modem. My Internet connection has been fine for nearly a year with the AEBS but for the past couple weeks has been disconnecting so frequently that it's almost become useless. The problems reported by the AEBS are: PPPoE Server (no PPPoE server found) and Internet Connection (AEBS doesn't have a valid IP address). It's always these two problems reported.
Restarting the AEBS gets me connected again, and sometimes the connection will come back on its own, but only for a short while. I don't know how to troubleshoot this. Help! Here are my AEBS settings:
Radio Mode: Automatic
Radio Channel Selection: Automatic
Wireless Security: WPA2 Personal
Use wide channels: Checked
Create a closed network: Checked
Use interface robustness: Unchecked
Sorry, I'm not a network guy so forgive me if I've omitted some important information. Below the log from a recent bout of connects and disconnects:
Jun 19 10:04:06 Severity:5 Disconnected.
Jun 19 10:04:09 Severity:5 Binding added for udp, 0.0.0.0:32816 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:04:09 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:06:40 Severity:5 Binding added for udp, 0.0.0.0:32817 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:06:40 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:07:37 Severity:6 Parameter updated - drTY.
Jun 19 10:07:37 Severity:5 unloading current configuration.
Jun 19 10:07:47 Severity:5 Connecting via ethernet (user "[email protected]" service "AT&T DSL Connection").
Jun 19 10:07:47 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
Jun 19 10:07:47 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
Jun 19 10:07:47 Severity:5 Rotated CCMP group key.
Jun 19 10:07:47 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:07:52 Severity:5 (WAN) link state is Up.
Jun 19 10:07:57 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:07:57 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:08:02 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:08:04 Severity:5 Associated with station 7c:6d:62:a2:dc:0c
Jun 19 10:08:04 Severity:5 Installed unicast CCMP key for supplicant 7c:6d:62:a2:dc:0c
Jun 19 10:08:06 Severity:5 Connection accepted from [::ffff:10.0.1.2]:61426.
Jun 19 10:08:08 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61428.
Jun 19 10:08:08 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61427.
Jun 19 10:08:13 Severity:5 Associated with station 00:24:36:90:4e:f6
Jun 19 10:08:13 Severity:5 Installed unicast CCMP key for supplicant 00:24:36:90:4e:f6
Jun 19 10:08:17 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:08:18 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:18 Severity:5 Binding added for udp, 0.0.0.0:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:08:19 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:20 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:22 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:26 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:08:27 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:08:28 Severity:5 Binding added for udp, xxx.xxx.xxx.xxx:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:08:32 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:08:32 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +0 seconds).
Jun 19 10:09:09 Severity:5 Disconnected.
Jun 19 10:11:32 Severity:5 Initialized (firmware 7.4.2).
Jun 19 10:11:34 Severity:5 Connecting via ethernet (user "[email protected]" service "AT&T DSL Connection").
Jun 19 10:11:35 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
Jun 19 10:11:35 Severity:3 No Address for NTP server time.apple.com.
Jun 19 10:11:35 Severity:5 Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
Jun 19 10:11:35 Severity:5 Rotated CCMP group key.
Jun 19 10:11:35 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:11:39 Severity:5 (WAN) link state is Up.
Jun 19 10:11:45 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:11:45 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:11:45 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:11:50 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +5 seconds).
Jun 19 10:11:50 Severity:5 Associated with station 7c:6d:62:a2:dc:0c
Jun 19 10:11:50 Severity:5 Installed unicast CCMP key for supplicant 7c:6d:62:a2:dc:0c
Jun 19 10:11:52 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61481.
Jun 19 10:11:53 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61483.
Jun 19 10:11:54 Severity:5 Connection accepted from [fe80::216:cbff:fe00:ee34%bridge0]:61484.
Jun 19 10:11:55 Severity:5 Associated with station 00:16:cb:00:ee:34
Jun 19 10:11:55 Severity:5 Installed unicast CCMP key for supplicant 00:16:cb:00:ee:34
Jun 19 10:12:02 Severity:5 Associated with station 00:24:36:90:4e:f6
Jun 19 10:12:02 Severity:5 Installed unicast CCMP key for supplicant 00:24:36:90:4e:f6
Jun 19 10:12:08 Severity:7 Public address reported as xxx.xxx.xxx.xxx to 10.0.1.4:5353
Jun 19 10:12:08 Severity:5 Binding added for udp, xxx.xxx.xxx.xxx:32769 to 10.0.1.4:5353 with lifetime 7200
Jun 19 10:12:08 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 10:12:25 Severity:5 Disconnected.
Jun 19 10:17:00 Severity:5 Connection established xxx.xxx.xxx.xxx -> 151.164.187.11.
Jun 19 10:17:10 Severity:5 Disconnected.
Jun 19 10:17:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 10:17:49 Severity:5 Binding added for udp, 0.0.0.0:32770 to 10.0.1.4:5353 with lifetime 7200
Message was edited by: DakotaPaul
This is what the log has looked like for the past several hours.
Jun 19 17:37:49 Severity:5 Binding added for udp, 0.0.0.0:32851 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:37:50 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:37:57 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:05 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:21 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:38:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:39:04 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:43:48 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:48 Severity:5 Binding added for udp, 0.0.0.0:32852 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:43:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:43:55 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:03 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:19 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:44:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:45:03 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:49:49 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:49 Severity:5 Binding added for udp, 0.0.0.0:32853 to 10.0.1.4:5353 with lifetime 7200
Jun 19 17:49:50 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:51 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:49:57 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:05 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:21 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:50:53 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:51:04 Severity:5 Binding dropped for udp to 10.0.1.4:5353
Jun 19 17:54:46 Severity:5 Rotated CCMP group key.
Jun 19 17:57:01 Severity:7 Network down reported to 10.0.1.4:5353
Jun 19 17:57:01 Severity:5 Binding added for udp, 0.0.0.0:32854 to 10.0.1.4:5353 with lifetime 7200
Thanks for any help you can provide. I'm about to throw the modem and/or router out the window!
Similar Messages
-
Constant disconnect with centurytel and wrt54gs
I set up dsl for my parents with centurytel, and linksys wireless router.
they can get online fine but seems like while they are surfing it constantly drops the internet connection. if you go to 192.168.1.1 it shows disconected and you have to either wait for it to reconnect or just hit the connect button.
I have it set up with auto dhcp and the router is set to 192.168.2.1 I have centurytel at my house and work with no problems what so ever, any ideas to remidy this?
I have gotten router update already, checked to make sure all the dsl filters are on all the phone lines. rechecked all the settings, reset both modem and router and started from scratch ect ect. is there something Im missing.
Thanks, JohnConnect a computer straight to the modem and check for a static connection...If that does not diconnect you, download the firmware for your router from here , re-connect your modem==>router==>computer...
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...
Then, unplug the power keep holding down the reset button for another 30 Seconds...
Plug the power back in, and keep holding down the reset button for 30 Seconds...
Release the reset button...Click here and follow the link to re-configure your router...Connection should be fine... -
Constant disconnects with Linksys BEFW11S4/Westell/Bellsouth Ultra DSL
I recently upgraded to the 6mb DSL service from Bellsouth. Previously I had the 3mb. Anyways everything was fine for sometime even with the faster service. The last few weeks I have been having constant disconnects(several a day). Naturally the wireless lite on my Linksys BEFW11S4 goes out each time. I then un-power the router then re-power and I'm off and running again. I am using a westell modem. Bellsouth tells me that its not them since i do have an internet coneection and referred me to Linksys. After several live chats(due to disconnects and then having to start tellin my issue all over again) they had me upgrade my firmware. Well did that and problem hasn't changed. I've played with the different router channels and they don't seem to help as well. Bellsouth told me that I had a static ip, so I tied setting up router that way, but then i got no connection. Unil reently everything was fine, this just started! Any help is greatly appreicated. My 17 yr old daughter is going through internet withdraws upstairs!
If you are on DSL using a Westell Modem; make sure you ask your ISP to bridge the Modem first and use the PPPoE fucntion on your router. Change the LAN IP of the router to something else like 192.168.2.1 so it won't get a conflict with the IP of the Westell. Then if you are on cable, you can try adjusting the MTU size to 1492, 1400, 1300, or 576 then check which value would get your connection stable. You can reset your router right after you upgrade it also, then reconfigure it again. Hopefully yell be fine after that!
"The war between heaven and hell depends on the choices we make, and those choices require sacrifice. That's the test" -
Constant disconnects with wireless router.
Hello and thanks in advance for any help you can provide.
I have a WRT54G wireless router with speed booster. I am experiencing constant disconnects when online gaming. I have one PC - running windows vista 64bit ultimate. This computer is running a wireless connection which is secured and is about 10 feet from the router through a wall.
I also have an xbox 360 with a wired connection. It doesnt seem to have the same issues but does become a bit sluggish at times.
I have called linksys and they instructed me on how to upgrade to the latest firmware. I think it is 7.5.0 or something. Still having issues. Cox (my ISP) has been out and says I am getting a constant 2mb download.
Any help would be appreciated. I have talked to linksys again they have me pull up cmd and run a test which shows me at a 4-10% packet loss. They say this is an acceptable rate.
Still the problems continue. If anyone can help I would be very greatful. If you need more info just let me know and I will provide whatever I can. Thanks!!!
Message Edited by madmike6537 on 11-26-2008 03:16 PMSounds like a vista problem, they are breading like rabbits it seems. The WRT54G is a good router, I had one for years with no problems. What type of wireless card do you have in the pc, and is it PCI or USB
-
Constant disconnecting with my WRT120N
Hi
I have a problem with my wrt120n. I'm having a constant disconnecting problem.
I don't have any problem with the wireless computers connected to the router but the wired one keep geeting disconnected. I'm loosing the internet many times a day on thiis one. Like I said the wireless is ok.
My old router on my computer ( wired) was working well before I installed the wrt120n.
Can someone help me?
Thank you!This is a problem of the Linksys/Cisco WRT120N product itself. The team from Cisco/Linksys is very irresponsible. Why i say so ?
The 802.11n signal is not certified to be supported but yet they have included this support in this router. By doing so, it causes this related problem that most consumers must be facing now or in the past. It is a shame that such a big company operates and sell their products this way.
The solution: It does not have anything to do with MTU, beacon interval etc.... Just use Mixed BG wireless signal instead of
Wireless N only when you goes to Manual Setup. I am sure that this solves the problem. -
Can anyone help with a screen that says ok to disconnect with a tick on the front? The ipod has frozen and I can't do anything!
Try a hard reset as described in this article.
How to reset iPod
B-rock -
E71 constant disconnects with bluetooth
My previous post was moved to "troubleshooting tips" but thats not the case, the problem is with the E71 phone itself. The blue ant headset i have works fine with all other phones
It contantly disconnects with the E71 , the problem is the phone. What can we do to fix the phone?Sounds like a vista problem, they are breading like rabbits it seems. The WRT54G is a good router, I had one for years with no problems. What type of wireless card do you have in the pc, and is it PCI or USB
-
"no valid IP address" error airport express as bridge with Dlink router
Hi there
I've read through many many posts and am unable to find the answer to my issue. I am trying to use my DLink DR 615 router as my main wireless router and then connect my airport express (brand new - n connection) wirelessly as a bridge. I would then connect my WD Live box to the ethernet port and connect the stereo connection to my receiver for itunes. at least, that's the theory.
Right now, I can't even connect. when I go through the manual process, I selected "connect through wireless network" and left the "configure IPv4" as "using DHCP".
problem is that it comes up as my wireless device does not have a valid IP address. Can someone help me step through how to make this work?
thanks so much!Suggest that you start over by holding in the reset button until the amber light blinks quickly. Hold another second or two and release.
Temporarily, connect an ethernet cable from your computer to the AirPort Express (AX) to help with the configuration. You can disconnect the cable when you have the AX configured.
Open AirPort Utility, click Manual Setup
Click the Wireless tab below the row of icons
Set Wireless Mode to "Join a wireless network"
(If you don't see this choice, hold down the option key on your computer as you click the selection box)
Wireless Network Name...the name of the wireless network created by your DLink should appear as a choice. Click to select.
Put a check mark in the box to Allow Ethernet Clients
Wireless Security...must exactly match the security settings of your DLink network
Wireless Password...must exactly match the settings of your DLinkk network
Click Update and AX will restart in 15-20 seconds.
You can move the AX to the desired location and hook up the ethernet cable. If your DLink is compatible with the ProxySTA function, you will connect. -
RV220W with BT Infinity and Static Public IP address
I've recently had BT Infinity installed with 5 static Public IP addresses.
Needless to say, the supplied BT Hub isn't really up to business standards - so it's been replaced with an RV220W router.
The router connects (via the supplied BT Openreach modem) via PPPoE and is allocated a dynamic IP Address.
Using one2one NAT I've tested that our static public ip addresses are reaching the router.
the RV220W router will be acting as a VPN endpoint as well as passing through certain services to servers.
I can configure the services to pass through using one2one NAT and individual static IP addresses, but the router doesn't use one of the static IP addresses for it's own - so I can't seem use a static IP address for the VPN endpoints.
Help please!Fixed ...
After a bit of fiddling around (reading out of date manuals! Cisco can't you at least update your manuals!)
The answer is in Firewall -> Access Rules
Add rule
Connection Type - Inbound WAN > LAN
Action - Always Allow
Service - Any
Source IP - Any
Send to Local Server (DNAT IP) -
Use Other WAN (Internet) Address - Enable
WAN (Internet) Destination IP -
It's also possible to fix the outbound IP address using rules:
Connection Type - Outbound Lan > WAN
Action - Always Allow (or you can schedule it)
Service - Any (or you can allow specific services)
Source IP - Any
Destination IP - Any
Use this SNAT IP Address - Enable
SNAT IP - -
Trying to instll iCloud on a new Toshiba laptop so I can sync contacts, calendars, email with my iPhone and iPad. Get error message HRRESULT:OX8007OBC9, says installer encountered errors before iCloud Control Panel 2.0 could be configured. Have the same problem trying to istall iTunes.
Quote from: lcwhitlock on 04-April-14, 13:44:09
Hello darkhawk,
Thank you for the recommendation. I somewhat understand what a MS DOS disk is, but I'm not sure how to go about creating one. I've seen where you can use a program, like Rufus, to create a usb one - but I'm leery about using 3rd-party programs (especially ones I'm not familiar with). I've come across a couple of 'how-to' tuts, but they didn't clarify what files (if any) I would need to include on the disk (for my particular situation). Right now I don't have any blank cds, nor any extra flash/thumb drives - wish I did, but hadn't needed these for years. There has only been one other time where I needed to re-install Windows, but that was over 15 years ago - I did it through BIOS, reformatting my drives, and then reinstalled via the Windows XP disk. Windows 8 is an entirely different breed, which has left me feeling a bit stumped, at times. If there was a way I could perform it (successfully), similar to the first time I did it years ago, I'd give it a try - but at the same time, I'm a bit reluctant, because if it doesn't work, then I'm stuck without any internet access to get further help.
Ask and ye shall receive. This should be doable in Windows 7 and Windows 8 on another PC. I recommend using a USB Flash drive like in this tutorial, but I'm sure you could use something else.
If you want, you could also use Hiren's BootCD to make a bootable CD with many options and programs on it (I keep one, just for certain situations) that will allow you to do the same things.
http://www.hiren.info/pages/bootcd
Also very useful for sorting out virus's as long as it's downloaded and made on another PC that is virus free...... -
Has anyone else seen the "Excel cannot complete this task with available resources" error message appear when Excel isn't even open? It keeps happening to me, and it's the strangest thing.
It seems like interacting with Excel files sometimes prompts it - for example, I just turned on my computer this morning, checked my email, and then opened Google Chrome to upload some Excel files. Excel hasn't been opened at any point since the machine
booted up, but this Excel error popped up while I was uploading the files.
Checked the Task Manager because I was baffled (not that this is the first time it's happened), and there's no Excel application running, just that silly error message. Choose OK on that error and a VBA run-time error message appears (not even sure if it's
Excel VBA or Word/Outlook but I assume it's Excel - it's the good old 1004, application-defined or object-defined error).
Debug is greyed out, so it won't let me debug to see what the problem is. Choosing End brings the "Excel cannot complete this task with available resources" message back for one final performance.
This happens on a not-infrequent basis: Excel isn't open, and I randomly get this set of Excel errors: 1) "cannot complete task", 2) VBA run-time, 3) "cannot complete task" again. Then it's done, until the next time it happens. Weird.
I have 32-bit Windows 7 and Excel 2013/2010/2007/2003/2002 (I know!) but the issue only started after installing 2013. I also get the "cannot complete this task" message regularly when working in Excel (generally with Power Pivot or something legitimately
memory-hungry though), and restarting the application does the trick. I don't mind a heads-up when I'm gobbling up too many resources, but when Excel's not even open, it's a bit ridiculous. It's like I have a zombie Excel! Does interacting with Excel files
via upload/moving around Windows Explorer actually trigger some sort of Excel action in the background?
Any ideas would be most appreciated!! Thank you :)Hi,
As the memory error messages , it can be very generic and don't always identify the real cause of the issue. We may try to use the KB that Mr. KR mentioned above to troubleshoot it.
On the other hand, if the file is xls format, we may convert to the new file format .XLSM and test.
http://www.experts-exchange.com/Software/Office_Productivity/Office_Suites/MS_Office/Excel/Q_28339883.html
Next, try to disable hardware graphics acceleration from File > Options > Advanced > Display section and disable Aero Themes (if you enabled) to check the results.
For the hangs and crashes issues, we may use ADPlus.vbs to troubleshoot:
http://support.microsoft.com/kb/286350/en-us
http://www.networksteve.com/exchange/topic.php/Excel_cannot_complete_this_task_with_available_resources_error,/?TopicId=39411&Posts=1
Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Hope it's helpful.
George Zhao
TechNet Community Support -
Constant disconnecting with HomeHub1
I've recently started having problems with my BT HomeHub1 and i'm stumped on what to do with this.
All devices connected to the homehub are thrown off in random intervals at the same time, and the broadband connection drops out of the list of wireless networks available in the area. But the lights on the hub remain the same, saying that it is still connected to the internet.
When I reset the homehub and let it load, it connects but then disconnects again and this problem repeats between 10 minutes to an hour.
There are no problems in my area when I checked the site
I tried the quiet line test and i've heard no crackling noise.
I tried finding that ADSL Line Status for homehub1 but there is no guide to get to that screen.
If anybody could help guide me into how to sort this out I would greatly appreciate it. Thanks.Its most likely a fault with the HH1 or its power unit. I have a HH1 and am on my second power unit.
This guide will tell you how to get to the ADSL stats ADSL Statistics
Or for a direct link, use this BT Home Hub 1 - DSL Connection
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
Air Play in my Apple TV disconnects from iPhone or Mac book after some time of playing. I need to restart the router in order to connect again. Apple tv is connected to wifi succesfully? Any suggestion?
I tried something new yesterday after reading all these messages. My ATV3 was situated on top of my satellite box and I noticed that it was quite warm. The instruction manual suggests that the box not go over a certain temperature, so I moved the box to a location without the heat under it. It now works without any problem at all...at least, so far.
-
Constant crashes with Edge Animate and Yosemite
I'm using Edge Animate running on a macbook pro and it is crashing every few minutes (like many others are reporting).
The program is up-to-date. I have uninstalled and reinstalled it.
Sometimes after a minute or two of working, the display features disappear. Old bounding boxes remain but, with some careful cursor action, I can still manipulate the image or symbol. . . until the entire program freezes. Other times things just stop working (e.g., motion paths). The only solution is to force quit the program -- the button on the crash notice rarely works.
Each time it crashes, it seems to create another Adobe Edge Animate CC 2014.1 Helper in the Activity Monitor (don't know what that means). I've tried deleting them but it doesn't help.
In the console, I get
2/18/15 9:16:30.612 AM Adobe Edge Animate CC 2014.1[4172]: *** Assertion failure in -[NSEvent subtype], /SourceCache/AppKit/AppKit-1343.16/AppKit.subproj/NSEvent.m:2427
There are 43 lines (!!!) that are identical to the one above.
This is obviously a known problem and needs to be acknowledged and fixed!Hi L Nordstrom,
- If you have Dropbox installed, uninstall the software and retry.
- If you are accessing files from a remote network, copy them to your local computer, and retry.
Let us know if you still face issues.
Thanks,
Preran -
Constant disconnects with flashing DSL light
Hi, my Infinity 2 connection has been unusable since last Friday 8th Feb. I get at the most a few minutes of up time then the connection drops with a flashing DSL light on the Openreach Modem.
I have tried power cycling the hub and modem, changed the cable to the socket and also relocated the modem.
I logged the call with BT on the 9th and on the 11th they marked the job as fixed, but it isnt.
This situation is very frustrating as I rely on my connection heavily for home and vpn to work but there seems to be no progress in a resolve.I phoned the helpline in the end and the guy the other end actually did a line test and found an issue. Apparently an engineer is booked but cannot come out until 21st Feb!!! That will be nearly 2 weeks downtime. I have not had the appointment in confirmed in black or white which is not reassuring either.
Really annoyed as when I had adsl with 02 any issue (which was very rare) got resolved either next day or within the promised 3 days.
I also didn't have to chase them to resolve it and they Defo didn't mark a job as fixed until it actually was.
Not very impressed by BT at all. I have phone, Bt Vision and Infinity 2 with them so I pay them enough every month.
Maybe you are looking for
-
ADOBE PHOTOSHOP CS6 COLOR PROBLEMS
hi i have a problem on adobe cs6, i am a photographer and i work heavily on my pictures, sometimes with graphic techniques(like lens flare, light leaks etc) and sometimes just with camera raw. i have this problem in the sense that i am satisfied with
-
I have just upgraded to 10.8 on my macbook pro and now I can't access itunes, videos and there is no sound - anyone help? It is an old macbook pro probably 6yo with the back lit keys - not under applecare anymore obviously. I downloaded the upgrade l
-
Help~~ORA-00257 archiver error. Connect internal only
I got this error when a login sql plus... ORA-00257 archiver error. Connect internal only, until freed. I tried to check in Unix...result as follow..: Filesystem size used Avail Capacity Mounted on /dev/dsk/c2t0d2s2 98G 97G 0k 100% /u04 I know th
-
How to install MobileIron apps@work on IPAd
Hi everyone, I try to download and install MobileIron on my IPAD by using Web Clip. According to the guide, I have to follow the link to load it onto my Ipad https://neptune2.mobileiron.com/mifs/c/api/v1/client/$DEVICE_CLIENT_ID$/appstore Could you p
-
i have to restart