Constant freezing eventually led to mini port not working

I run bootcamp, and it happens on windows as well so it must be a hardware problem. Unfortunately my coverage is up and I'm unable to pay for anything right now.
Basically, the computer was freezing up for a while, a lot of the time it just freezes up for a couple seconds, or a few seconds at a time, and then sometimes it runs fine. Other times it will completely freeze and I'll have to do a hard shut down. Now my mini port stopped working(I was using an adapter for VGA), also both on windows and mac sides. Computer still freezes up. Just had the hard drive replaced a few months ago when it was under warranty, and it was fine until about a month ago.
Not sure what to do, I keep things pretty clean, I used to build PC's. I ran dsk chk everything was fine.
I want to open this thing up but

Thanks to whoever moved this topic to the correct place.

Similar Messages

HT4623 My iPad mini is not working right ?? On some apps

My iPad mini is not working right on some apps

You can always try to reset your device and see if it helps matters any:
Device Reset (won't affect settings/data/music/apps/etc)
1. Press and hold (& continue to hold) BOTH the Sleep/Wake button & the Home button.
2. Continue to hold BOTH (ignoring any other messages that may show) until you see the Apple logo on the screen.
3. Release BOTH buttons when you see the Apple logo and allow the device to boot normally.

My ipod mini si not working and I can't find the answer.

My ipod mini is not working. I have done all the R things. It won't switch on unless I toggle the hold key, once switched on it asks me to choose a language but pressing the select button does nothing. Can it be saved or should I throw it in a heap with my Dyson vacuum?????????

It's no longer under warranty? Rather than throw it away, there are 3rd party repair site here in the UK (iPod Doctor is one).
Might be worth a try because it seems like a hardware issue rather than software.

MSI GAMING 5 - ALL USB ports not working

hello
how are you every one
i have problem with rear usb port i can use it in safe mod and bios only but it does't work when the operition system start i try to slove the problem i updated bios i have other pc and same specification and it's work without any problem but with this mother borad rear USB ports not work also the USB ports on the case ALL USB PORTS NOT WORKING
Mouse and keyborad work in bios but if the system run don't work ! and trun off
and all usb devices
in safe mod work
rellay i don't know where is the problem !
CPU : Intel Core i5-4690K
M.B : MSI Z97 GAMING 5
RAM : G.Skill Ripjaws X 8GB DDR3 Kit
GPU : Gigabyte GeForce GTX 970 G1 GAMING
SSD:Corsair force LX 256 GB
HARD: Seagate Barracuda 1 T.B 7200 RPM
CPU COOLER : Cooler Master Hyper 212 Evo
PSU : Cooler Master GM-Series 750 watt
CASE : NZXT Phantom 410
Thank you

Quote from: Nichrome on 28-January-15, 00:18:47
Hi,
What about if you try to install drivers from your product's page?
http://uk.msi.com/support/mb/Z97-GAMING-5.html#down-driver
And when exactly it starts to fail to work? Did you try to have OS just installed, restart it and see if it works then? Are you able to determine which driver installation causes USBs to stop working?
thank you
i just remove USB3 controller driver and work
thank you all :D

Touchsmart TX-2 fingerprint scanner and USB ports not working

Hi everyone,
Please forgive me if this is in the wrong spot.
Just sent my laptop (Touchsmart TX-2 1015au) off for a warranty fix - told them the USB ports weren't working on Windows 7, 64 bit. It came back wiped, running on Vista 32 bit and.....with the USB ports not working.
I figured I'd try to get it working because I need my laptop for uni and can't send it back right now. So I clean installed Windows 7, 64 bit again and its still not working. Did the standard open device manager and uninstall everything under the usb tab. All that has resulted in is causing the fingerprint scanner to stop working (being told that it is not connected) and still no working USB ports.
All advice really welcome and very much appreciated!
Thanks in advance

Hi:
Should be no problem to get W7 32 bit to work on that model.
Just use all of the drivers and software from the HP Probook 450 G0 on your model except the Audio, BIOS and firmware files.
Your model uses the Intel HD graphics driver only.
The first driver you have to install is the Intel chipset installation utility and then reboot.
http://h20565.www2.hp.com/portal/site/hpsc/public/psi/swdHome/?cc=us&lang=en&sp4ts.oid=5359407&ac.ad...
Audio: Accept the agreement. Download and install the first driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=24&Level=4&Conn=3&DownT...
If for some reason, the Intel HD graphics driver from that model does not work, then use this one...
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23713

My usb port not work and hot usb port aria please help me

my usb port not work and hot usb port aria please help me

Hi
Please find the link givenbelow might help you to fix your issue.
USB Device Troubleshooting
Fix Windows 7 “USB Device Not Recognized” Error
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Hp 15-D018TU USB SS PORT NOT WORKS

Hi, In my HP 15-d018tu Notebook PC the USB SS port not works.Can anyone look into this problem and guide me.
Thanks in Advance

Hi:
Did you install the applicable usb3 driver?
http://h20564.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_135422_1

The volume down button on my iPad mini is not working.

The volume down button on the right hand side of my iPad mini is not working. I can turn the volume up but not down for sum reason. My father thinks I should take it and have it fixed but I'm wound earring if it's sum thing else!

Thanks; I tried this last night and it didn't work. I think it might be a software issue and will return it tomorrow. I'll try restoring one more time.

HT1766 please help my ipad min is not working on the scren it says iPad disabled connect to itunes

please help my ipad min is not working on the scren it says iPad disabled connect to itunes

How can I unlock my iPad if I forgot the passcode?
http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
You may have to do this several times.
Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
 Cheers, Tom

My IPhone 4s is freezing up and the wifi will not work. This happened after the update. I have tried to restore it and that did not fix it. Any suggestions?

My IPhone 4s is freezing up and the wifi will not work. This happened after the update. I have tried to restore it and that did not fix it. Any suggestions?

Most of your purchases content can be downloaded again via the Purchased tabs in each of the store. I realize that this will be a problem for the iTunes Store on the iPad, but that has nothing to do with apps, since apps are in the App Store.
If you backed up synced with iTunes before you restored the iPad, your content should be in iTunes on your Mac and you should be able to sync it back again.

Ports not working--mac freezes during hardware test

My immediate problem is my mac freezing during the hardware test. I know it can take some time for the test to be completed, but it was over an hour and it was frozen at "2 min 16 seconds," and the mouse and keyboard aren't recognized. Even during the short test.
I held the power button down and turned it off.
The bigger problem is non-functioning ports. First it was the firewire ports to my maxtor hard drive and then my lacie superdrive. And it's not the cord or the units. They work other places. That was approx. a month ago. I didn't worry too much and went back to the internal drive.
Then today my internet stopped working. The modem is not reading the computer and the computer is not reading the modem. The modem works fine with my laptop thank goodness (although it's a PC we bought for the kids to play computer games on and it's driving me crazy!). So the modem and cord are fine.
Then a couple of my USB ports were not happy today. One wouldn't read my daughter's ipod touch, but then later did (?).
And to go back to the very beginning, sometimes when I put the computer to sleep, it freezes on a black screen with a working mouse pointer, but nothing else and I have to force quit. If it goes to sleep on its own, it's fine.
Here's what I have done today: done the PRAM boot, some other command-option-O-F boot, tried the hardware test twice--it froze twice. Repaired all the permissions, reset the thing. All this I found out on the discussion groups.
I have read a lot of posts of similar problems and tried what was said there.
Am I heading for a crash? I cant back up my new stuff because the firewires are non-functional. I can't burn bunch of stuff to discs because the superdrive is going bad and won't burn properly (which is why I bought the LaCie which my computer now won't recognize.
I can't get anything off my computer except in bits and pieces with 2GB usb drive.
I know I'm rambling, but I've just spent 5 hours trying to fix this thing. Any suggestions? I'm going to take it in to the apple store to get it repaired tomorrow, but I'm worried I will lose all my data. Also I am scared of what it will cost. Is there anything else I could do tonight?
I'd love to have something else to try. Many thanks,
Barbara
Message was edited by: Barbara R.
Message was edited by: Barbara R.

HI Barbara,
It sounds like the hard drive is failing or has failed. Boot from your Mac install disc and if you can run Disk Utility in case the startup disk needs repairs.
Insert your install disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
*(Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)*
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
When you are finished with DU, from the Menu Bar, select Utilities/Startup Manager.
Select your start up disk and click Restart
While you have the Disk Utility window open, look at the bottom of the window. Where you see Capacity and Available. *Make sure there is always 10% to 15% free disk space*
If you cannot boot from your install disc, try booting in Safe Mode
What is Safe Mode
Carolyn

Mountain Lion Mac Mini Server Ethernet Port Not Working

I have a Mac Mini Server and once I upgraded to Mountain Lion Server the Ethernet port is unresponsive. It worked before upgrading. Is there something with Mountain Lion Server that is causing the Ethernet port not to work properly?

Make a "Genius" appointment at an Apple Store.
Back up all data on the internal drive(s) before you hand over your computer to anyone. If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
*An SSD doesn't need to be zeroed.

Apple Mini Display Port NOT working at resolutions over 1600X1200!

Problem:
Apple Mini Display Port does NOT work at resolutions over 1600X1200 on NON Apple Cinema Displays.
That means if you own any other brand of monitor such as NEC, Lacie, etc. you will NOT get native resolution on your 24 inch monitor as it is stuck at a maximum resolution of 1600X1200.
This story was mentioned on "Macbreak Weekly" show 4-14-2009. I have since checked with a few people and it would indeed seem to be true at this point.
I REALLY hope a solution from Apple comes soon and this is not some new policy of theirs. If so, it may be the last Mac Pro I will or can ever own. The reason is I do a lot of 3D work with C4D, Vue, Modo and Photoshop CS4 so I MUST have a monitor like the high-end ones from Lacie that have 100% color gamut and Adobe RGB. I can NOT be tied down to an Apple Cinema display due to that work. At this time, it seems this means I would only get 1600X1200 resolution on that 24 inch monitor.
Has anyone else confirmed this too and if so what the heck is Apple thinking or better still going to do about it? I LOVE my Mac Pro but if they start forcing displays on us then I won't be buying another Mac, it's just that simple.

Thanks, but I think two things may be different in that setup.
1. If I understood correctly, it's a first gen without a "Mini Display Port" and
2. It was a laptop not a Mac Pro with a video card.
I think it has specifically to do with either one or both of the above combos. In particular I think it's the video card they are putting in them.
I am not sure if a new 2009 Apple laptop with a Mini Display Port connected to a NON Apple display would have an issue or work like yours does now. It would be interesting to get to the bottom of this for sure because it REALLY hurts people like myself that are into 3D design.
I will try to get back on this once I continue to find out more details.

Mini dv port not working

When the mini dv port stops working, is there anything software wise that might resurrect it? This is on a refurb (from Apple) 2008 MBP, and the port was never actually used for anything until this past week, and it is not working. Could it be software related? Suggestions for repair? I've looked everywhere but it seems this is a very uncommon problem.

When the mini dv port stops working, is there anything software wise that might resurrect it? This is on a refurb (from Apple) 2008 MBP, and the port was never actually used for anything until this past week, and it is not working. Could it be software related? Suggestions for repair? I've looked everywhere but it seems this is a very uncommon problem.

Mac Pro USB and FW800 ports not working

I've been reading tons of forum entries in the Apple Support Community and in other forums. Nothing seems to answer quite what's going on with my Mac Pro Tower.
Here are the details and steps taken up to now:
- I'm running a Mac Pro Tower (MacPro 3,1, 2x 2,8GHz Quad Core, Early 2008 model), currently running OS 10.6.8
- I moved before the holidays in December and left my computer unplugged for over month while away. Didn't have any issues before the move.
- up until the last couple of weeks, I had actually been running on Leopard (yes, I'm a luddite!, please, no teasing )
- I was trying to update my ipod touch's iOS and kept getting errors preventing it from completing the process. At first I thought it was an ipod app causing the issue after having read a few threads on that topic...
- Also, on startup, the Mac started searching for a Bluetooth keyboard, of which I don't have, and would not detect my usb keyboard. I would disconnect and reconnect the keyboard and the majority of the time, the Mac would then recognize my USB keyboard.
- I decided to upgrade to Snow Leopard, which didn't help with the iPod update. I did not do a clean install.
- Then I noticed that my USB stick wasn't working and tried it in all the usb ports (except the ones on the keyboard)
- Also, I had removed and then reinstalled printer and scanner drivers for my All-in-one printer. After this I kept getting constant communication errors between the mac and the printer via the usb port, although I was able to print a test page.
- I've used Hardware Test once which didn't detect any issue.
- I reset the SMC
- I reset the PRAM, and for a few seconds I was able to read from my USB stick, then never again, even after another PRAM reset.
- I've cleaned the whole inside of the computer and checked for loose cables. Cables are in so tight it's so hard to loosen them!
- I now tested all the ports:
     ∞ the 2 front and 3 back USB ports are unresponsive to my usb key and to my VoyagerQ dock
     ∞ the front and back FW800 ports are unresponsive to my VoyagerQ dock
     ∞ However, the keyboard works in any fo the back ports and my USB stick is recorgnized by the USB port of the keyboard.
     ∞ I also plugged in my Logitech webcam into the keyboard and it works there but not in any other port.
     ∞ When I plug in USB powered speakers into any of the ports, they work fine
     ∞ And the FW400 ports are also working fine with my VoyagerQ dock
- a few times, including once today, my mac restarted by itself. The times before today, I thought it was because I was sort of moving back the computer in place, but today I was nowhere near the computer.
So what does this all mean? Should I do a clean install of the Mac OS? Or is it a problem with my Logic Board?
Any insight please would be helpful. I had Apple Care and missed the reminder to renew it so I really hoping not to spend more money than necessary.

Thanks Grant,
The battery is a start and something inexpensive to replace.
I did do a PRAM reset (command + option + P + R) and was able to hear the chime 4 times. I tried resetting it a number of times over the past week, as well as yesterday with no success in reviving the USB ports. But isn't it weird that my USB powered speakers work by plugging them in any USB port (with the mini jack pugged in the back or front earphone plug)?
I did not use the USB ports on the keyboard until yesterday, so that is not the cause of the other USB and FW800 ports failing. But I'll follow your suggestion and not use them except for the mouse.
Another weird thing that happened yesterday, I have 16GB of RAM and I spent all day trying to troubleshoot a RAM issue that is magically fixed after leaving the computer on overnight to do an extended Hardware Test. The issue was:
- Only 8 RAMS were being recognized
- a red LED light appeared on the top riser
- first I thought I had isolated the faulty RAM bar, and then a second one
- Then going pair by pair again, I no longer saw the LED light
- Put back all 8 bars, only 8 GB of RAM recognized
- Left computer overnight running Hardware test (said it took almost 3 hours, with no errors)
- Now all 16 GB are recognized!
Thanks again for the tips

Constant freezing eventually led to mini port not working

Similar Messages

Maybe you are looking for