Constant Loosing Connection With Wireless

I have had my Wireless Router for almost 7 months and it has constantly about 6 times loosing my connection. I have made many calls to Linksys. They have been very helpful and gotten my back online. But it just continues..

Go to Linksys website and install the latest wireless router firmware, also install latest driver for your wireless adapter. Also you can check other factors that can affect wireless signal. Hope can help you..

Similar Messages

I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows 8?

I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows

Hi, stig2013.
I would recommend the steps in the article below. See the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
If you are receiving an error message, find the exact error number that you recieved in the article below and process the steps.
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
This error occurs when the device unexpectedly loses its USB connection with iTunes. This can occur if you manually disconnect the device during the restore process. You can resolve this issue by using USB troubleshooting, using a different Dock Connector or Lightning Connector to USB cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.
Cheers,
Jason H.

Impossible connecting with wireless network Netgear WNR 2000

I can not log on to my wireless network (Netgear WNR 2000) with my macbook. My other PC:s work fine and connect always. My Macbook only connect after I have restarted the router. When I use my Macbook in other places I can connect with wireless network. What is the problem?

I'm assuming that you're using the right network password! After that, the most common causes of difficulty are:
- The router not set up for DHCP and so cannot allocate an IP address to the MacBook
- The router has "MAC" Address Authentication (a security feature - don't mistake MAC for Mac[intosh]) turned on and the AirPort MAC address isn't in the pass list.
- The default "Automatic" location in System Preferences > Networks has been modified so that it no longer works.
Bob

Got new ATV and all set up. It keeps loosing connection with iTunes on laptop and have tried everything suggested in set up guide. It works fine for a while then the iTunes account vanishes from 'computer' menu TV screen. Full Wifi signal on both devices

Got new ATV and all set up. It keeps loosing connection with iTunes on laptop and have tried everything suggested in set up guide. It works fine for a while then the iTunes account vanishes from 'computer' menu TV screen. Full Wifi signal on both devices so can't think what could be causing it to happen. Any suggestions please?

Sorry, I updated another thread I was a part of but didn't update my own thread.....ughhh!
I updated all of my ATV 2's and 3's to the latest firmware when it was released and have been problem free since. I do believe the major issue of not being able to connect after a period of inactivity has been corrected with the latest ATV firmware.
I can look at my network connection table using "netstat -an" in a CMD window and I do not see the massive number of connections I saw before the update.
Here is a link to the other thread I was referring to above:
https://discussions.apple.com/message/19952545#19952545
Have you applied the latest firmware updates to your ATV 3's?

IPod nano does not connect with wireless earphone via bluetooth transmitters.

My iPod nano(6th) can not connect with wireless earphone via bluetooth transmitter.
I want to know which is wrong iPod nano or bluetooth transmitter...Now I tried with i10s because I thought previous one (motolora) might be wrong.
But both can not connect.

Sounds good. Hopefully they can provide you with an accurate answer.
B-rock

MacBook looses connection with external monitor

Hey Apple humans!
I have a MacBook Pro (mid 2009) and an external monitor Samsung SyncMaster XL2370 connected via DVI/DisplayPort. Works fine since the mid of 2009 but in the last few days the MacBook looses connection with the monitor and isn't able to get the connection up again. The button "Monitore recognise" (don't know the exact translation of it in english) in preferences doesn't work, even a reboot brings nothing.
I've changed nothing on the setup, only the newest patches for OS X were installed. Any ideas?
Thanks in advance and sorry for my bad english, right now I'm to ****** to concentrate
Message was edited by: FabianFerdinand
Message was edited by: FabianFerdinand

have a Mac Pro with 2 Samsung syncmasters and after updating os x to 10.6.6 computer loose the connection with the monitors. Randomly it seems, might work for a while and suddenly go black.
Have to restart the Mac. I'm sure it's related to the os update. Tried all resets, throwing prefs, emptying
cache but nothing helps.
Jesper

Why my IPAD2 sometimes loose connection with my router and I need to enter again the WPA password?

Why when my IPAD2 loose connection with the router sometime I need to enter again WPA2 password?

same problem here.
MBA (latest os), even my ip5 (latest ios) & ipm (also latest ios) looses the connecntion.
Ive tried to figure out what causes the problem - neither my xbox360 nor (and i guessed they will be the problem) the pcs here...
the connecntion runs well.. switching also (MBA-IP5-IPM).. but not for longer than an hour.. or even minutes. When the connection looses a high-frequency noise is followed by silence. A restart fix that problem and all devices streaming well... but not for long...
any suggestions?

HT1414 Since updating to iso6.0 I have had problems with my email exchange account syncing correctly - I keeps loosing connection with the server.

Since updating to iso6.0 I have had problems with my email exchange account syncing correctly - I keeps loosing connection with the server.

Are you losing the connection to iTunes on the iPad or the computer? You are saying that iTunes is updated. Of course iTunes is updated when you update the iOS software. That's a no brainer.
If you mean that iTunes is updated on the computer, that has absolutely nothing whatsoever to do with downloading and updating apps on the iPad itself so changing the date on the iPad, signing in and out of the stores on the iPad .... Doing any of that on the iPad would have nothing to do with iTunes on your computer.
If .... you have not been able to connect to the iTunes or app stores at all on the iPad - try this ...
Settings>Privacy>Location Services>System Services (swipe to the bottom of the page to find this)>Location Based iAds>Off.
If the downloads are stalled or "waiting" - try these suggestions.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
Make sure that you do not have a stalled download in iTunes - a song or podcast .... if you have a download in there that did not finish, complete that one first. Only one thing can download at a time on the iPad so that could be what is causing the problem.
If you can't connect at all - you can also try rebooting your router. Unplug it from power for about 30 seconds and then plug it in again.

Loosing connection with my xbox360

Hi everyone, I just purchased a wrt160n router and I am wireless with my xbox360. While on xbox live playing an online game "cod4" I can't get through a game most of the time without loosing a connection, with the 54gs router I had there was not an issue. Any help would be appreciated!!

Try few wireless settings on the Router ...
Access setup page of router ....
Click on Advanced Wireless
settings>>Change the Beacon Interval to 75 >>Change the Fragmentation
Threshold to 2304 Change the RTS Threshold to 2304 >>Click on "Save Settings" ....
See if it shows stable connection with X-BOX ....

Router looses connection with modem

My WRK54G wireless router keeps losing connection with my Comcast broadband modem. My connection with the router remains, but I lose internet connection. After rebooting the modem and router, my connection lasts no more than 5 minutes.
I tried to upgrade my Firmware but it did not install corrctly. (error during upgrade).
Any ideas on what I can try?

If you loose the connection on all the computers(wired and wireless) then, you should connect a computer straight to the modem and test the internet connection...See what happens and if you face the similar problem then it is not your router...
If you have stable connection straight from the modem, then, you should upgrade your router's firmware...
As the upgrade failed, you need to download TFTP Utility...Also download the router's firmware from here , make sure you select the correct version and then download the firmware...
Double click the tftp.exe file and click run :
For Server- Enter the IP Address of the router that you assigned. By default, the router is 192.168.1.1...
For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
For File- Click the triple “…” button and browse for the .bin firmware file...
Click Upgrade button to start upgrading. A progress bar should show up to show the progress.
Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

WRT1900AC and Macbook Pro Retina - refuses to connect with Wireless N

I have the first generation Macbook Pro Retina, and just recently upgraded my D-Link D-655 for the Linksys WRT1900AC. I also put the router on the first floor (the D-Link was in the basement) because there were some huge holes in wireless coverage I hoped to fix.
To my dismay, the thing will not negotiate a connection with ANY wireless N device as wireless N. When I set it to wireless-N only on 5 GHz, nothing will connect to it, and same with 2.4 GHz. My macbook's system report shows the network as being Wireless G on the 2.4 band and wireless A on the 5 GHz.
I have 50 MBPs internet here, and when I plug directly into the router, I get that. However, I am maxing out at 20 MBPs over wireless with both my macbook and my Samsung Galaxy S4.
I'm about at wits end, my next step is to return this thing. I have been on hold with support for 20 minutes, which is freakin eerie because they have no hold music or talking so it's just dead silent.
This morning I spent an hour on a live chat with support, and nothing she had me do made it better, and in fact any changes made it drop from 20-21 MBPs down to 16-17 maximum.
On her advice, I re-installed the firmware, downloading from online, and this had absolutely no effect. Any other ideas to try? I get these crappy connection speeds sitting 3 feet away from it. I live in a house, so no massive interference from neighbors (only 2 other wifi networks are visible)
Solved!
Go to Solution.

let me be clear here: I had the same slow speed with both my mac and my galaxy s4, it is not a mac problem. I had disabled media prioritization and the WMM thing in the settings for media prioritization. Yes I am sure I am connecting to the right SSID. The old router is DIR-655. Part of the reason I wanted to upgrade is it disconnected my galaxy s4 every 2 minutes (and many people have had that problem, a quick google search verified that the router just doesn't like galaxy s4). OS X 10.7.5 but as I said my Galaxy has the same issue - it does not connect as wireless N, and when I make the router Wireless N only, not one of the computers in the house can connect to it. That includes a Mac Mini, Galaxy S4, Macbook Air, Macbook Pro Retina, and a Chromecast (which only works on the 2.4 band, but same issue there).

Satellite M30-154 cant connect with wireless internet (wifi)

hello,
i did a product recovery on my m30-154 a couple of days ago, and now he doesnt connect with the wireless internet we have in our house. he sees the SSID but he just dont connect, i allready did a BIOS update and an Intel update and I dont dont know what to do now. Can somebody help me?
cheers

> he sees the SSID but he just dont connect
The SSID is secured. Right?
Can you connect to open Wlan?

Issues with client looses connection with 6.0.196.0

Hi,
We recently upgraded our Wisms to version 6.0.196.0 and after the upgrade we have seen the clients sometimes looses connectivity and has problems to connect. We use an network with 802.1x and PeapMschapv2 with dynamic WEP.
We have disabled aggresive load-balancing but still see the issues.
Any ideas anyone?
Regards,
Martin

Hi,
Any news for these problems? Did the version 7.x fix these CAPWAP UP/DOWN problems with HREAP APs? It seems that I'm having these same problems now. Local APs seems to be fine, but HREAP APs goes UP/DOWN with versions 6.0.196.0 and 6.0.199.4.
There are three 4404 WLCs, where are different sites' office and warehouse APs connected to. The environment is configured as N + N + 1
like following:
WLC1 is for officeAPs. APs are 1131 and they're configured as H-REAP
WLC2 is for warehouseAPs. APs are 1242 and they're configured as Local
WLC3 is for backup and I used this for testing.
After I updated all the WLCs at summer to version 6.0.196.0, there have been issues where the clients looses randomly WLAN-connections. But the complaints just came from the two largest offices. And these didn't happend immeaditly after the update, but after few months. It can be that the summer holidays was reason for it. After some investigations, I updated the WLC3 for version 6.0.199.4, which just got released at the time, and moved these two largest offices' APs to there. Complaints stopped but after a month the second largest office informed that the clients' disconnections started to raise again and the WLAN-network has become unstable again. First there was just couple of issues but it have been raised as the time goes by.
When I made some more investigation to this site, I noticed that the APs' CAPWAP goes DOWN and UP randomly for a second:
*Nov 12 07:39:29.537: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN
*Nov 12 07:39:29.590: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Nov 12 07:39:29.590: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Nov 12 07:39:29.759: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Nov 12 07:39:29.811: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 12 07:39:29.812: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Nov 12 07:39:29.849: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 12 07:39:29.850: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 12 07:39:29.889: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Then I investigated some more and noticed that this happens on all of the H-REAP APs and almost in the same time:
*Nov 12 07:39:29.537: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, second largest site's AP (6.0.199.4)
*Nov 12 07:40:17.439: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, second largest site's other AP (6.0.199.4)
*Nov 12 07:41:20.297: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, largest site's AP (6.0.199.4)
*Nov 12 07:42:31.928: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC1, random site's AP (6.0.196.0)
When I checked the warehouseAPs, which are configured as local in the WLC2 (6.0.196.0), there was nothing like this in the logs. Logs are clean.
But when H-REAP is configured for these APs, the clients should not be disconnected when the CAPWAP goes down? And this whole "process" seems to last just for a second. Not sure if this is the real reason for these client disconnections, but at least this is not normal. I haven't heard complaints from smaller sites, even when APs at them also does the same.
I don't feel great to update the WLCs for the version 7.x, because it just seems to be new feature release, but if it fixes these, then I should think about it. Has someone, who had these same problems, got this fixed with version 7? Or has TAC provide some other patches for this?
Thanks,
Joni

Lose connection with wireless keyboard/ mouse

I'm using 10.9.1 and continually losing the connection with the wireless keyboard or the bluetooth mouse. I've changed the batteries. I've gone to System Preferences, clicked on keyboard and used the assistant to re-connect. But why is this happening at least every 3 days. First the keyboard. Then the mouse.

Hello peachfuzz123,
The following article provides some additional troubleshooting that may help stabilize your Mac's connection to your mouse and keyboard.
Troubleshooting wireless mouse and keyboard issues
http://support.apple.com/kb/TS3048
Cheers,
Allen

IPhone 5S loose connection with soundlink bluetooth bose

The iPhone 5S loose the connection with the soundlink Bluetooth Bose ? When I connect iPhone 4 with the some device there is no problem.
Do you know if there is some solutions ?
Thank you very much
Zampilla

Not a generic issue ,my iPhone 5S works with Sounddock 10, soundlink and soundlink mini all perfect
Check to see if you have too many paired devices on Bose and sometimes you can only pair with one device at a time

Constant Loosing Connection With Wireless

Similar Messages

Maybe you are looking for