Constant Reboot after software update

I just performed Software Update on my Leopard MacBook Pro and now it's in a constant reboot cycle. The grey boot up screen displays for 90 secs or so and then reboots and the cycle repeats. There were three programs for update but the only two I remember were iTunes & Front Row. How do I recover? Thanks.
Kevin

Just to add some more detail to the issue:
I've reset the NVRAM by holding down the Option/Control - PR at bootup and it seemed to work in that it then rebooted again. But nothing else but the continuing reboot cycle.
Next I tried to get into Safe mode by holding down the Shift key on bootup but this did not work. I inserted the Leopard DVD on bootup but it just spins.
Help!!!
Kevin

Similar Messages

Unable to Reboot After Software Update - Unable to Reinstall Mac OS 10.4.10

Hello,
I just bought a Macmini 9 months ago, and I believe I may need to either erase the HD to reinstall the original Mac OS (10.4.10) or else replace it. However, I am not familiar with Mac and don't know how to reformat the disk. Can anyone help?
Each time there is a software update, I experience problems starting up from the HD. After the last update a few days ago, I am unable to start up from the HD at all. I tried using the original install CD 1 to reinstall Mac OS 10.4.10 with archiving. However, I received an error saying "unable to install because there is a newer version already installed." Therefore, I tried to start up from the HD again by pressing Option key at startup, but the Macmini continously turned off by itself without rebooting. I tried reinstalling Mac OS with the erase option, but it failed. After that, the Mac OS install CD1 only gives me the option to reinstall additional applications, but when I select continue, there is not HD shown to install the applications.
Disk Utility First Aid on CD1 was unable to repair the disk. I received the following messages: "Invalid sibling link", "Volume check failed", "The underlying task reported failure on exit", "1 HFS volume checked", "1 volume could not be repaired because of an error."
At the bottom of the page under Disk Utility, the following information about the disk is available. Format: Mac OS Extended (Journaled); Capacity: 111.5 GB (119,690,149,888 Bytes); Available: - ; Used: - ; Number of Files: - ; Owners Enabled: - ; Number of Folders: - .
System Profiler is able to identify type, disk identifier, file system, etc. It shows the volume supports journaling, but is not journaled.
Scan Image for Restore shows Library_Preferences (Empty), and Root applications are all grayed out.
I performed the Apple Hardware Test (ver 3A129) by pressing D at startup. The test ran for 5 minutes and 6 seconds. It reported "No trouble found".
It seems the HD is empty, but the install CD is not offering any options to reinstall the OS, only the additional applications. I believe it is a partition error, but I am not familiar with Mac and hesitate to proceed any further.
How do I reformat the disk so that I can reinstall the original Mac OS 10.4 and 10.5?
Your help is sincerely appreciated. Thanks.

Good news!
The usual reason why updates fail or mess things up, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates.
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.

Q10 stuck at reboot after software update - PLEASE HELP

Hello
I was checking for software updates for my Q10 yesterday and was informed that there is a new update
I clicked on download and install, and it asked me to reboot when it was done. After that it loaded very slowly until it reached 99% 6 hours later and it remained like that for 12 hours
What I did this morning was remove the battery and sim card and I reinserted the battery, the same thing happened again and it is moving very very slowly
Can you please help?? I would rather find away in which I do not loose my BBM contacts since I have not backed up my phone...are the contacts stored on my blackberry ID or will I loose them if I reset the phone?
Thank you very much

It finally powered on after 3 battery pulls, but now it does not make or receive calls (((
Everytime I connect it to blackberry link it says software update available, so I clicked on install, it said downloading update and then nothing happens, the download bar becomes full then nothing changes
I also tried to reload device software, i got a message saying checking repair software and it stayed like that for 3 hours then the device rebooted but nothing happened at all
I even tried redoing the software update from the phone itself 3 times, everytime it would say update successful but the phone would still not make or receive calls
Please help I dont know what to do....could the problem with blackberry link be that im using it on a mac??
I appreciate your help

IPhone 4 frozen in reboot after software update

In the process of updating phone to iOS 7, (which has missed a couple of updates) it is frozen with apple logo and status bar on screen after software downloaded and installed. The phone has been connected to a computer for this update. How do I reboot?

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work.

PowerMac Desktop keeps rebooting after Software Update (Java, security, QT)

Since my Software Update through Apple yesterday, my Desktop keeps "rebooting" every minute or so. Any ideas?
www.robertholland.com

Mine is doing that too. I posted a couple hours ago asking the same thing, and nobody has answered me either. If someone gets back to me before you, I'll let you know, and if you could do the same that would be great!

Force software reboots after Software Updates install, and do a WUA rescan upon reboot and install any remaining patches?

Running SCCM 2007 SP2 R3 and having two big issues with SUP that impacted us severely with the February patches. An RDP patch from November broke our 2-factor authentication (2FA) method, so we stopped deployment until Microsoft could fix the
patch. Rather than fixing the patch...they made a patch for the patch.
We divided our servers up into multiple Day/Time maintenance windows, like SUN, MON, TUE, and from 0200 to 0600 AM, and we run deployments weekly as needed.
There doesn't seem to be a way in SUP to "let SCCM control reboot" and ALWAYS reboot (whether the patches request it or not), and, as a result, we seem to have an awful lot of servers that are stuck at "reboot pending" after patch installation,
and have actually taken to using a third-party program to reboot the servers.
There also doesn't seem to be a way to force SCCM SUP to rescan the computer after the patch is applied until after a day...or, for servers, a week (from Mon to Mon, for example).
What happened this time around was that the first patch installed and broke 2FA, the second patch is not recognized as being needed until after a reboot and rescan--since that did not occur, it took up to a week to get the second patch installed (IF the
server ever was rebooted), which...was unacceptable.
Soooo...how can I:
1. ALWAYS force SCCM to reboot after patching (60-min countdown if user logged-on), just like we do with our normal deployment advertisement, package, program.
2. Force a WUA scan after this reboot, so, if remaining patches from this patch group are needed, they get detected and installed, and hopefully this will all work within the 4-hour window (we might be able to extend it earlier,
but, not past 0600).
Thanks!

Thanks, Don. OK, if there is a "reboot required" returned at the end of the patch deployment...shouldn't the computer then reboot? We see a large number of computers with "reboot required" that never reboot. Is there something wrong in
the setup to stop a reboot from occurring?
Thanks.
It looks like you've continued the conversation with Jason and it's taken an interesting turn ;)
But, in the case where a reboot_required is the returned resultcode, CCM will look to your MW and deployment settings, and the context of the installation event (enforcement etc), to determine if the reboot request should be honoured or refused.
You should be able to see all the to-and-fro of this logic within the client logfiles, as it's occurring (or after the event).
If you do some spelunking into the logfiles, don't forget to look at windowsupdate.log (the WUAgent logfile), as that can, with the CCM logfiles, paint a more complete picture of the "flow of things".
This does all assume that the client machine is in a healthy and predictable state to begin with.
If there is already some other pending_reboot hiding in the background, or, WUAgent is running with it's own configuration (potentially fighting with CCM), or, it's Win8 with the "Automatic Maintenance" scheduled task, you can get some unexpected behaviour
(but usually that is unexpected reboot, rather than unexpected no-reboot)
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

How do I get my iphone to reboot after software update?

After using itunes to update my iphone, the phone went into a loop and when I try to slide power off, the phone goes back into the slide to unlock screen.
How can I reboot the phone?

Hi ..
Instructions for you here > iOS: Syncing your data with iTunes

How long to reboot after software update?

I just did a system update and it had to reboot when finished. It got as far as a blue screen with a spinning gear-wheel and that's it. It has been like this for 15 minutes. Is this normal? Will it hurt if I use the power button to shut it off, then restart? It has never taken this long before.

I assume by blue screen and spinning gear you are referring to the shutdown portion of the restart rather than the restart itself. If this be the case then 15 minutes seems a bit long. Normally, I don't like recommending abnormal shutdowns because of the possible problems they can cause, but in this case it should be OK. However, I strongly suggest you first boot from your Snow Leopard DVD and repair the hard drive and permissions:
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
This will hopefully assure no disk damage from the abnormal shutdown. If all is OK then restart the computer normally.

IMac G4 in 10.3.8 (I believe) won't reboot after software update

Three or four weeks ago, my Mac came up with available Software Upgrades (I believe one was a new version of iTunes, and there was something else). I just told it to download and went about my business; when it wanted to reboot, I told it to go ahead.
I haven't seen it since.
I've zapped the PRAM. I've tried rebooting in Safe Mode. It just goes back to the gray apple screen. I've tried opening the CD tray to see if I could boot from a startup CD, and the keyboard responds correctly to the command-option-P-R and shift keys, but not to the CD tray button, and I don't see another way into that tray. (I'm also not finding my 10.3 disks, but that's my problem, not yours.)
This is obviously not my primary computer, since I haven't needed it in several weeks; I'm not 100% sure it's in 10.3.8, but I think that's what I saw on the About screen last time I looked. I hope that machine's not dead and buried, but if it is, so be it; I just have some data I need to get from it, and I can't get it to boot so I can pull the files.
Ideas?
Thanks for your time!

I am not sure this will work as you can't boot properly, but try restarting it holding down the mouse to open the CD tray.
If you have found your install CD's and it is possible to insert it in the now open CD, run Repair Permissions and Repair Disk from the Disk Utility from the CD.
Without the CD, perhaps you can get some benefit from this article.
Resolve startup issues and perform disk maintenance with Disk Utility and fsck.
I would concentrate on the fsck section.

Droid Maxx keeps rebooting after software update

Since the upgrade on 11/1/14 to 23.3.24, my droid maxx keeps rebooting. It has done this about 15 times since yesterday evening. Any ideas as to what could be causing this? It is also telling me that I need my GPS on and set to high accuracy mode in order to detect my location. Before the upgrade, I only turned my location on when I used the navigation app. Any ideas?

The Latest update is suppose to get the Phone prepared for Verizon's voLTE it's hard to say how long it will be till all is functioning correctly with the system and the phones but, if your issues continue & it makes the phone unusable then I'd see if you can get another Droid Maxx hopefully one with out the new update..
My Current: Version is 21.11.21. my Maxx is still running with no issues

Ever since I received my Macbook Pro in July 2011 I've had issues with my wireless connection at home. After software updates, Apple support suggested I reboot my router which works. But now I have to do it every other day. ????

Ever since I received my Macbook Pro in July 2011 I've had issues with my wireless connection at home. After software updates, Apple support suggested I reboot my router which works. But now I have to do it every other day. ???? AT&T my DSL carrier suggests I get a new router. Apparently the one I have is really old and doesn't support my Macbook Pro. Does this sound right?

If your using WEP encryption yes, Apple has discontinued that becaues it's worthless. WEP (and WPA) is cracked so encryption makes no sense.
Get a new Wireless N router, set it up with WPA2 (AES) Personal and two different 20+ randon letter/numbersymbol character passwords
One for Admin access only of the router, keep this on paper off all comptuers in a safe someplace.
One for entering into devices, computers etc for Internet Access Only.
You need the long and random password to defeat brute force attacks by GPU software that the hackers have now.
Also if you give out the password to another, they can't hack the network with the guest access password.
Computers remember the internet password, so anyone with access to your machines or network will have the password.
Since you have another Admin only password, they can't hack in. got it?
You don't need "Invisible" or "MAC Address filtering" that's a waste of time as hackers can sniff a network and causes issues getting on the network.
Good luck.

I am installing for 1st time apple tv and after software update no reboot

I am installing Apple TV for 1st time and have done a software update. There is no reboot after the update. I do not want to turn off and on to restart the unit. What should I do?

If unpowering it and restarting doesn't help I think you'll need to buy a cable
You could try the 'black display' troubleshooting steps:
http://support.apple.com/kb/HT1551?viewlocale=en_US&locale=en_US
Specifically I wonder if the AppleTV may be trying to connect with an unsupported resolution giving a black screen. Try cycling display resolutions using these remote commands in step 6:
If your TV screen appears fuzzy or black (you see no video)
Make sure the television you are using supports the Apple TV resolution requirements. Please see the Apple TV technical specifications.
When you connect power, check to make sure the LED turns on. If the LED is not on, then verify with a known good power outlet or connect something else to the outlet you're using for Apple TV and make sure it works (such as a lamp or clock).
Make sure you're using the correct video cables and that they are connected firmly to Apple TV and to your TV.
Connect the HDMI cable directly into the Apple TV and your television, remove any third party devices or adapters.
Make sure the input setting you've selected on your TV matches the input you have your video cables connected to. See the documentation that came with your TV for more information.
Change the Apple TV resolution by pressing and holding the Menu and Up button for six seconds. The Apple TV will automatically cycle to the next resolution at approximately 20 second intervals. Pressing the Select button will immediately cycle to the next resolution.
If you are connected via HDMI, try unplugging and replugging your HDMI cable.
If HDMI isn't working on an Apple TV (1st generation), try component cables instead (and disconnect the HDMI cable temporarily). Read more about HDMI vs component video.

S4 Constant Rebooting after update

Issue is affecting four of my devices. Two of the devices are having this issue with only factory apps and blank sd card, these device came directly from VZ with no accounts installed before and after update.
Restarting is random. Not linked to power save, sleep, calls, apps, or anything else I can test.
Devices are unusable. Please offer a roll back.
Devices have been factory reset, cache cleared, and operated in safe mode. The issue persist across all.

Read post 54 in this thread here... Re: Galaxy S4 randomly rebooting after VRUFNG6 update!
In a nutshell, re-enable any disabled apps you have on your phone and power off and back on. You can then disable the apps if you would like.
This is a temporary workaround. Verizon and Samsung are working on an update (supposedly) which will not be out for a while.

IPhone went bad after software update - iPhone 5 is now stuck on Itunes connect and has vertical lines

iPhone went bad after software update - iPhone 5 is now stuck on Itunes connect and has vertical lines.
I found a video on youtube with similar issues - http://youtu.be/Xuuqxx18-bA
EVERYTHING HAS BEEN TRIED: Restore, Reboot, Recycle, Replacing Cables, etc....
I don't have Apple Care, what to do? Spend more money and buy a new phone?

Here is another person who has a problem with the iPhone 5 screen https://www.youtube.com/watch?v=sc1ZPWSA8dc and they have just received them NEW!!!!!
I myself, two days ago purchased a 2nd hand iPhone 5 that was advertised as having a line of squares at the bottom of the screen. I Googled it and found people saying it was a screen issue and to replace the screen, so I did this and it is still happening with a new screen.
I am starting to dislike Apple intensely after reading forum posts and watching videos where people are asking for help and telling us about issues that they are having with their phones.
Why is Apple getting it so wrong with their updates and manufacturing that they are completely destroying iPhones that cost a lot of money and then expecting the owner to purchase another phone unless they are still in warranty.
Apple you should be going out of your way to put things right for people but instead there is a wall of silence over so many of the issues destroying peoples phones.
SHAME ON YOU!

After software update apple rv light flashing and not coming on

After software update my apple tv did not come on and light is flashing I tried in pluging and all what next for me

It was probably applying the update and rebooting, unless it had doin it for awhile?. You will need to grab a micro usb cable and restore in iTunes
http://support.apple.com/kb/HT4367

Constant Reboot after software update

Similar Messages

Maybe you are looking for