Constant uploading during and after opening Safari

Hi- for the last few days, every time I open Safari, it immediately begins uploading upwards of 300 kbps of data, and continues even after I quit and have no other applications open. I had thought this kind of thing doesn't happen to Macs, and it seems I can't find any instructions anywhere on how to stop it. Any help would be appreciated, thanks.

I have no idea where it's going, or what is sending it; my internet connection is just constantly uploading while Safari is on and keeps doing it, without any applications open, until you restart the computer.

Similar Messages

Safari dosn't open any webpage , when it reload page stuck and nver open, safari dosn't open any webpage , when it reload page stuck and nver open

safari dosn't open any webpage , when it reload page stuck and nver open, safari dosn't open any webpage , when it reload page stuck and nver open

I was fed up getting messages such as:
Safari can't open the page...
Safari can't connect to the server.. etc
I tried everything to get my Safari 3.1.1 to work on my Mac Pro computer (OS X 10.5.2) - then I found the solution for my Mac accidentally - it was due to Intego Net Barrier X4 that I had installed on my computer.
What I did was to upgrade to NetBarrier X5 and, after installation, I deleted the old intruder Stop List under NetBarroer's 'Antivandal' Stop List button. Now I can visit all the sites that previously did not open in Safari 3.1.1. However, I am not sure whether it was the upgrade or just deleting the intruder stop lists that did the trick.
So, before you upgrade to Intego NetBarrier X5, try and delete the stop lists under the antivandal button first in your existing NetBarrier X4. Highlight the intruder list (click on the first intruder at the top of the list and, while holding down the shift key, click on the last intruder on the list, thus selecting all of them), and then press the 'minus' button below the list. This will remove all the intruder items in the stop list. Restart your computer, open up Safari and now check if you can access sites previously inaccessible by Safari. If not, upgrade to NetBarrier X5 and it should work. Well at least in my case.

I'm using acrobat pro in my project after debuging the project and after opening a certain number of PDF files I receive the message: the maximum number of files opened has been reached, you have to close some files to continu.even doing that, I steel rec

I'm using acrobat pro in my project after debuging the project and after opening a certain number of PDF files I receive the message: the maximum number of files opened has been reached, you have to close some files to continu.even doing that, I steel receive the same message.Some one can tel what to do please? Thanks

Hi Memalyn
Essentially, the bare issue is that you have a 500GB hard drive with only 10GB free. That is not sufficient to run the system properly. The two options you have are to move/remove files to another location, or to install a larger hard drive (eg 2TB). Drive space has nothing to do with SMC firmware, and usually large media files are to blame.
My first recommendation is this: download and run the free OmniDiskSweeper. This will identify the exact size of all your folders - you can drill down into the subfolders and figure out where your largest culprits are. For example, you might find that your Pictures folder contains both an iPhoto Library and copies that you've brought in from a camera but are outside the iPhoto Library structure. Or perhaps you have a lot of purchased video content in iTunes.
If you find files that you KNOW you do not need, you can delete them. Don't delete them just because you have a backup, since if the backup fails, you will lose all your copies.
Don't worry about "cleaners" for now - they don't save much space and can actually cause problems. Deal with the large file situation first and see how you get on.
Let us know what you find out, and if you manage to get your space back.
Matt

I am using iphoto 6.0.6 and after opening the application it drops below the dock. I can see it when I use expose to reveal all open windows but once selected it drops below the dock.

I am using iphoto 6.0.6 and after opening the application it drops below the dock. I can see it when I use expose to reveal all open windows but once selected it drops below the dock.

Try trash the com.apple.iPhoto.plist file from the HD/Users/ Your Name / library / preferences folder.
(On 10.7: Hold the option (or alt) key while clicking on the Go menu in Finder to access the User Library)
(Remember you'll need to reset your User options afterwards. These include minor settings like the window colour and so on. Note: If you've moved your library you'll need to point iPhoto at it again.)
What's the plist file?
For new users: Every application on your Mac has an accompanying plist file. It records certain User choices. For instance, in your favourite Word Processor it remembers your choice of Default Font, on your Web Browser is remembers things like your choice of Home Page. It even recalls what windows you had open last if your app allows you to pick up from where you left off last. The iPhoto plist file remembers things like the location of the Library, your choice of background colour, whether you are running a Referenced or Managed Library, what preferences you have for autosplitting events and so on. Trashing the plist file forces the app to generate a new one on the next launch, and this restores things to the Factory Defaults. Hence, if you've changed any of these things you'll need to reset them. If you haven't, then no bother. Trashing the plist file is Mac troubleshooting 101.

[svn:fx-trunk] 5473: Fix for bug around handling of constraints during and after effects were run , both for old and new effects.

Revision: 5473
Author: [email protected]
Date: 2009-03-20 16:02:58 -0700 (Fri, 20 Mar 2009)
Log Message:
Fix for bug around handling of constraints during and after effects were run, both for old and new effects. Fix was to correctly record and handle styles that were set or not set in either state and to temporarily set width/height values for the duration of an effect if we disabled the relevant styles that affect width/height.
QE Notes: None
Doc Notes: None
Bugs: SDK-17809
Reviewer: Jason
Testing: checkintests, Mustella Effects, ListDataEffects
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-17809
Modified Paths:
flex/sdk/trunk/frameworks/projects/flex4/src/mx/effects/effectClasses/FxAnimateInstance.a s
flex/sdk/trunk/frameworks/projects/framework/src/mx/effects/Effect.as

Revision: 5473
Author: [email protected]
Date: 2009-03-20 16:02:58 -0700 (Fri, 20 Mar 2009)
Log Message:
Fix for bug around handling of constraints during and after effects were run, both for old and new effects. Fix was to correctly record and handle styles that were set or not set in either state and to temporarily set width/height values for the duration of an effect if we disabled the relevant styles that affect width/height.
QE Notes: None
Doc Notes: None
Bugs: SDK-17809
Reviewer: Jason
Testing: checkintests, Mustella Effects, ListDataEffects
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-17809
Modified Paths:
flex/sdk/trunk/frameworks/projects/flex4/src/mx/effects/effectClasses/FxAnimateInstance.a s
flex/sdk/trunk/frameworks/projects/framework/src/mx/effects/Effect.as

Role of PI developer during and after upgade SP in PI

Hi PI Gurus,
Can any one guide me, what all the activities I need to keep in mind before and after going upgade to SP.
We are currently using PI7.1
The interfaces which are in QA system, are they going to be impacted? Can I transport objects during upgrade, or i have to wait for upgrade of all the 3 systems.
Regards,
Krishna

Hi,
Before starting SP upgrade, Unregister the queue in SMQR and close all the communication channels.
After upgrade, we have register the queues and start the CC. Test all the channels for the connectivity.
Check all the links in RWB i.e alert inbox, message monitoring etc.
Regards,
Krishna Chauhan

[Dell E5510] Blank screen during and after boot

Hello,
I performed system update some time ago (2 or 3 weeks) and left my computer unused. Today I tried to power on it and I was very surprised, because I didn't see anything on screen during boot and after it. I rebooted computer in fallback mode (I also added "i915.modeset=0" to kernel init args), and I saw command line. Then I updated whole system and rebooted it again - no luck again blank screen during boot and after.
I rebooted it one more time, but with default kernel (I disabled KMS again via GRUB command line) and I saw systemd output during boot. I teems, that all services were started successfully, because all messages were prefixed with "OK". Then I cloud only use command line, because Gnome 3 was not running under seventh console.
Any idea what is going one here?

Hi there Sudarshan21,
I would recommend taking a look at the troubleshooting steps found in the article below.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
-Griff W.

HT4623 I uploaded IOS6 and after it was done I lost Safari?? Why did this happen and how do I get it back??

I uploaded the IOS6 last night. Everything went smooth until I realized that I didnt have Safari any more. What happened and how do I get it back??

Is Safari disabled in Settings > General > Restrictions?

Crash on start up and after opening (when I can get it running)

HP DV6
Windows 7.1 Home Premium
Intel HD 4000
nvidia GT650M
Read the forums and tried using "run as admin" and "right click and set graphics card" and press the shift key. I finally can get it started. BUt now I can't get it to actually perform a function once open beyond create a new project.
Have NOT tried updating nvidia driver (due to OEM warning)
Have NOT tried editing BIOS (really? edit bios to run an adobe product)
Please advise - after 3.5 hours of trying to get this product working, about done

I had a similar problem. I finally purchased AVG tune up and let it run all of its stuff. It cleaned the registry files and let me optimize the performance of my machine. I went to lower settings on the graphics card and made sure the RAM was using about 75% of the available RAM for Adobe software. After that the program has been running great.
There could be other programs out there that do the same things. I'm only familiar with AVG on a PC. On a mac I have used MacKeeper with good results.
Previous to this I had completely uninstalled ALL OF ADOBE PRODUCTS 3x and reloaded them without any success. The tech had sent had sent a list of directions to follow.
In my un-technical opinion, the performance default settings on the download are too high for most machines. I had a similar problem with Photoshop, but it would stay open long enough to change the performance settings. Once I did that with PS its been fine since.
For all the problems I have had in the last two weeks and the hours spent getting this to work (and now I'm working on the export running like a turtle in a snow storm), I would take a Mac with FPC 7 any day.
Hope this helps. T

SPA112 FW bug confirmed: registration broken during and after outbound call

After receiving and configuring my new SPA112, everything seemed to work out just fine: registration to the SIP proxy, inbound calls, etc. However, at some point I discovered that outbound calls would typically only work for a certain amount of time, after which the connection to the callee would be lost, just like the my registration to the SIP proxy. In the SPA112's Web interface, the device reports "Registration State: Failed" in such cases. Only a reboot of the device will result in a successful registration again. Firmware version: 1.3.5(004).
To diagnose the problem, I enabled both syslog and debug logging and started capturing and analyzing what is going wrong:
[Before call]
SIP.REGISTER
SIP.TRYING
SIP.UNAUTHORIZED (with nonce)
SIP.REGISTER
SIP.TRYING
SIP.OK
Also the debug logging reports "LOCAL3.DEBUG: [0]RegOK. NextReg in X".
So far, so good.
[During/after call]
We see two (periodic) registration sequences:
SIP.REGISTER
SIP.TRYING
SIP.UNAUTHORIZED (with nonce)
LOCAL3.DEBUG: SIP_tsClientEventProc(event: 28)
LOCAL3.DEBUG: SIP_regTsEventProc(event: 28)
LOCAL3.DEBUG: SIP_tsClientEventProc(event: 28)
LOCAL3.DEBUG: SIP_regTsEventProc(event: 28)
LOCAL3.DEBUG: SIP_regTsEventProc(event: 28)
LOCAL3.DEBUG: SIP_tsCreateClient()
SIP.REGISTER
SIP.TRYING
LOCAL3.DEBUG: SIP_tsClientEventProc(event: 28)
LOCAL3.DEBUG: SIP_regTsEventProc(event: 28)
SIP.OK
LOCAL3.DEBUG: SIP_tsClientEventProc(event: 28)
LOCAL3.DEBUG: SIP_regTsEventProc(event: 28)
LOCAL3.DEBUG: [0]RegOK. NextReg in X
Which is OK and the same as before the call. This one is however shortly followed by the following (second registration sequence of) debug messages:
LOCAL3.DEBUG: SIP_tsClientEventProc(event: 4)
LOCAL3.DEBUG: tryAltIp_delay()
LOCAL3.DEBUG: RSE_DEBUG: getting alternate from domain:<proxy>
LOCAL3.DEBUG: SIP_regTsEventProc(event: 4)
LOCAL3.DEBUG: SIP_regTsEventProc(event: 32)
LOCAL3.DEBUG: 2. RSE:GetServerAddrErr(<proxy>,0)=-101
LOCAL3.DEBUG: SIP_tsCreateClient(), 1781, uiTmrF=1600, SIP_TMR_F_INIT=1600
LOCAL3.DEBUG: [0]Reg Addr Change(0) 29dfc552:5060->0:5060
LOCAL3.DEBUG: tpError at [SIP_tsCreateClient:1817]
These two registration sequences (regular SIP messages at the one hand and the debug messages at the other hand) are alternating, and the succesfull registration is followed by the failing registration in a short time, so most typical state is "Failed".
Any suggestion on what I could try to solve the issue is welcome!

I'm able to reproduce the problem in my test lab.
It seems that device can't fetch IP address of the SIP proxy from it's internal cache during active call (GetServerAddrErr error -101). And the issue doesn't solve in full even after the calls end.
It is not networking issue between device and DNS server as no DNS query has been issued (the IP address is cached from previous query that has been responded successfully).
As a workaround I configured proxy IP instead of name.
It work.
It seems we hit (another) firmware bug.

Utility Disk crashes after opening Safari

Hi Can anybody say me why if I surf with Safari later I can't open Utility Disk ( program crashes) Thanx

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the name of the crashed application or process in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V).
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
Still in the Console window, look under User Diagnostic Reports for crash reports related to the process. The report name starts with the name of the crashed process, and ends with ".crash". Select the most recent report and post the entire contents — again, the text, not a screenshot. In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.) Please don’t post shutdownStall, spin, or hang logs — they're very long and not helpful.

When i connect myipad mini to laptop i tunes doesnt open automatically and after opening it doesnt show devices column or anything now how do i sync my ipad for songs and apps

in the welcome menu of itunes i had switched off an option of openning itunes automatically whenever ipad is connected
now how do i undo it

OK. That's the big issue right now.
First of all, i asked the hosts to remove your screenshot because you have posted information in that screenshot that you do not want other people to see, so if you post back and see that is gone, I made the request.
For the device not being recognized, try this first. Disconnect the iPad, quit iTunes, reboot your PC and the iPad and then try again. Use another USB port on the computer if you have one free.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
If that doesn't work, start with this support article for more help.
http://support.apple.com/kb/TS1495

Crashed during and after itunes export

I wanted to export a track to itunes from GB3. My itunes resides on external drive. When given the command to do so, GB3 displayed itunes as if it had never run. It cleared my whole list. (The files survived.) I then copied them to the "new " itunes, reset all preferences and smartlists and though I was fine. But the next time I restarted my imac, all user preferences were lost. It was as if I had turned on the machine for the first time. itunes library (again), Address Book, bookmarks, my Pictures file wont open (says "volume cannot be found"), and worst of all 3 GB# songs are gone completley. Somehow Home documents were saved. Needless to say, I am not looking forward to ever turning my computer off ever again. Is there a way to retrieve my GB# tracks? How do I get my Picture file found? Can i reverse Sync with .mac to save address book and Bookmarks even though they were not officially backed up but still show up on the .mac site. Can I ever restart my computer again?
Please help!
imac 17 intel dual core Mac OS X (10.4.6) LaCie d2 250GB

You are right. it is a system issue...although I have to stress that the original loss of my itunes library happened as I was attempting to export a track to the itunes library (on an external drive) from Gargeband 3. Is there a "way" to do this beside "export track to itunes?" Did it matter that itunes was on an external drive?

During and after downloads, the file is not viewable in the download window. I can find the file later by going to Explore and selecting my documents/downloads.

When I download a file the download window opens but not files are viewable. I cannot execute a file from this window. I can open the download file using Explorer and then execute the file from there. Why are the files not viewable.

In the Finder,navigate to your projec folder. Look in the Shared Items folder. Is there a video ffile inside? Does it play intact?
Russ

Copy Paste doesn't work during and after a remote login session

Hi
I am using a Windows 7 Home Premium Service Pack 1 laptop to login into Linux. I am using Putty and Xming to SSH and view the desktop. Whenever I start a session the copy paste functionality gets disabled in my laptop,i.e., I cannot copy text from one text
file to another or within the same text file. The copy paste doesn't work even upon closing the connection.
From what I have gathered it is not possible to copy from one computer(host) to another(guest) during a remote login session but I am not able to copy within my windows laptop.
Is there some setting that I need to change to prevent it from happening? What are the possible solutions?
Thank You
Rishabh

Hi,
Are you able to copy and paste in the putty session, with mouse or keyboard?
Using PuTTY
http://the.earth.li/~sgtatham/putty/0.52/htmldoc/Chapter3.html
Please restart your PC to check whether you can get back the copy and paste function. It can be caused by some compatibility issue.
Please also run "sfc /scannow", check if it find and fix any errors.
NOTE
This
response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you.
Microsoft
does not control these sites and has not tested any software or information found on these sites.
Regards
Yolanda
TechNet Community Support

Constant uploading during and after opening Safari

Similar Messages

Maybe you are looking for