Contact Center Enhanced License for Cisco 2951 Router

Hi,
I need an urgent help to get the exact part number/details of Contact center enhanced license.
I couldn't find in CCW or any other tool about this license with Cisco 2951 Router (CISCO2951-V/K9).
To run this license on mentioned router, do we need to order it separately or we can take it with router?
Please respond asap.

Hi Andre,
I was just refering the Ordering guide which says
Updating UCSS contract when upgrading Unified CCX licenses
UCSS cannot be upgraded from one category to another (e.g. Standard to Enhanced). If
the customer upgrades within the solution, they need to purchase UCSS for greater or
equal value to cover the new version, then they can request a credit on the unused term
of the original purchase from Customer Service
you can also speak to [email protected] for more details on ESW.
regds,
aman

Similar Messages

  • Cisco 2951 router AC-PoE power consumption, meaning of the mention "Platform Only" in the datasheet.

    Hello,
    I have a question regarding the power consumption of a Cisco 2951 router with an AC-PoE power supply (without PoE boost).
    In fact in the table (n°7) of the Cisco 2900 Series ISR (G2) datasheet, that sum up the power consumption data for Cisco 2900 series routers there is the line : "Maximum Power with PoE Power Supply (Platform Only) (Watts)", and I would like to know what is exactly the meaning about the mention "Platform Only".
    Thank you for your help, best regards,

    Hi @francois.trarieux,
    This is the maximum power that is consumed exclusively by the router from the PoE PS (Power Supply). The power capacity that the PoE PS gives to other PoE devices (IP Phones, Cameras, APs, etc) is specified in the line below "Maximum End-Point PoE Power  Available from PoE Power Supply (Watts)" of the datasheet.
    HTH.
    Regards,
    Martin, IT Specialist

  • Cisco view for Cisco 7201 router

    Hi ,
    We have LMS 3.0.1 and we are not able to get cisco view for Cisco 7201 router.
    Any help would be appricated.
    thanks,
    Samir

    Make sure you have version 22.0 of the Rtr7000 CiscoView package loaded.  You can update your CiscoView packages under Common Services > Software Center > Device Update.

  • Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

    Hi All,
    We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
    Any help would be appriciated.
    Thanks in advance
    Samir

    Hi,
    *** Device Details for d0151-100 ***
    Protocol ==> Unknown / Not Applicable
    Selected Protocols with order ==> TFTP,SSH,HTTPS
    Execution Result:
    Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
    This is the error while doing syn archieve.
    I am not sure about Rtr7000 version but we have latest Rtr7000.
    Waiting for your kind reply.
    Samir

  • SAP Contact Center new component for Incidents

    Hi All,
    From today (10.6) we have a new component “CRM-CCI” (Contact Center Infrastructure) available for SAP Contact Center related incidents.
    You can still use the old “CRM-BCM” components, but as you can notice the system recommends “Please use CRM-CCI” The old component CRM-BCM will be deactivated during Q4/2014.
    Regards,
    Jukka
    SAP Contact Center team

    Hi Jukka,
    I would like to look at the documents linked in the above post (in relation to BCM support on IE11 and Windows 8.1), but when I click on the links, I get prompted for login and password. My usual Marketplace login and password don't work.  Could you advise at all?
    Thanks,
    Adele

  • What's "SAVE" configuration command for Cisco switch/ router?

    What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well,
    but so long, any other command that easy to remenber?

    What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well, but so long,
    any other command that easy to remenber?
    yes, here: Switch#write,and want to know more about the Cisco switch, please visit:http://www.3anetwork.com/cisco-switches-price_c1

  • Contact Center and TeleService  for Internal Emplooyees

    Any one has information on enabling contact center and teleservice for Internal Employees?
    We are planning to use for HR call center for internal employees

    What version are you looking at? In R12, the contact center allows pulling up an employee record and then you can log a service request.
    In 11.5.10, you can use service request form or HTML Service pages to create service request for HR Help desk requests.
    You can use Zoom functionality to navigate to appropriate HR forms from SR form.

  • User License for Cisco CUCM 7.1.3

    Hi
      I need 30 unit license for Cisco Communication Manager 7.1. But I found that it's already  end of sale.
     I want the unit license part number for cisco cucm 7.1.3 version.
     And i found revised part numbers for user license (CUCM-USR-LIC ) but those for 8,x versions. If i purchase that will it support in CUCM 7.1.3?
    Thanks in advance.

    Hi,
    CUCM 7 is already end of sale.
     CUCM 7.1.5 supports UCL.If we refer the ordering guide of CUCM 8.5, you can get UCL licenses [Basic/essential].
    http://www.cisco.com/web/partners/downloads/partner/WWChannels/technology/ipc/downloads/UC_8_6_OG.pdf
    What I think if u place the order , you should get the licenses and at the backened, it would be DLU.
    You can also speak to Cisco SE for further clarity.
    regds,
    aman

  • Contact Center 85 license upgrade and services related

    Hello,
    A customer of mine wants to upgrade his contzct center licenses, from ENH to Premium, he has a valid contract of ESW ans UCSS services for the enhanced licenses on his deployment.
    I would like to know, is it necessary for him to buy ESW and UCSS along with the upgrade PN (L-CCX85-85U-E-P-S1)?
    Thank you.

    Hi Andre,
    I was just refering the Ordering guide which says
    Updating UCSS contract when upgrading Unified CCX licenses
    UCSS cannot be upgraded from one category to another (e.g. Standard to Enhanced). If
    the customer upgrades within the solution, they need to purchase UCSS for greater or
    equal value to cover the new version, then they can request a credit on the unused term
    of the original purchase from Customer Service
    you can also speak to [email protected] for more details on ESW.
    regds,
    aman

  • Security License for Cisco 3900 Series

    Hi,
    I am having    Security License  (SL-39-SEC-K9)  for Cisco 3900 Series router, Can somebody help me to provide sample config to configure 3945 router to act as firewall. Is there any difference with the native IOS based firewall config..
    Regards,
    Mukesh           

    Here is a detailed instruction on ISR G2 licensing (including downloading, installing, rehosting license, etc.).
    Usually, you just need to go to cisco.com/go/license, enter PAK and follow detailed instructions.
    HTH
    Alexandr

  • ASA license for Cisco IP Phone over VPN

    Hi,
    Are there special licenses required on the ASA to use Cisco IP Phones (Hard phone) over SSL VPN connection?
    Thanks

    Hi,
    You can purchase the phone proxy license. This elimiates the need to build a VPN tunnel for voice traffic.
    It is not mandatory to purchase this license however.
    From the ASA configuration guide:
    http://www.cisco.com/en/US/docs/security/asa/asa83/configuration/guide/unified_comm_phoneproxy.html#wp1144845
    "The  Cisco Phone Proxy on the adaptive security  appliance bridges IP  telephony between the corporate IP telephony  network and the Internet  in a secure manner by forcing data from remote  phones on an untrusted  network to be encrypted. "
    Don't forget to rate all posts that are helpful.

  • Optimal configuration for Cisco E3000 Router

    Hi All,
    Following are the details of my current home network setup, I would like to hear more recommendations and drawbacks of this setup.
    ISP has provided with a Cisco  DPC3825 DOCSIS 3.0 Gateway which has 4 Ethernet ports and a wireless networking but only 2.4 GHz.. This router is connected to the cable CPE box to internet. I have enabled the Firewall features of this router and disabled the Wireless network. This has also the DHCP server running. 
    The Second router is a Cisco E3000 which supports 2.4 GHz / GHz wireless networking. Connection to gateway is made via the 1st Ethernet port of gateway and then to the Internet port of E3000 router. I have connected my wireless devices to E3000 with GHz wifi lan. This router also has the firewall activated and DHCP server running as well.
    Both routers have WEP2 Personal / AES security configured. Currently these two devices are on two different IP ranges ..etc gateway is 192.168.0.1 and e3000 is 192.168.1.1.
    The E3000 is primarily configured for my online video for TV (Panasonic Vireacast). Please let me know if this is the best configuration or any other possible options.
    Thanks,
    RG

    This configuration is called LAN to WAN configuration and this is the best configuration considering that you want to behave both the router as a router.
    Because the other confiuration would be LAN to LAN then you can only use 1 router as a router and 2nd router as a switch.
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=529c188bc0ee4f7da79ffc22f2be33ec_4579.xml&pid=80&r...
    The first configuration in the article is is LAN to LAN, scroll down the window for LAN to WAN configuration.

  • Licensing for Cisco ESA c380

    I am putting a recommendation together for a client to upgrade their existing Cisco ESAs and trying to figure out how the licensing works.
    We are looking at c380s across multiple sites, upgrade from their current models which are c160s. Questions:
    1.) Do the mailbox licenses need to be procured separately for each c380. For e.g., if the total mailbox no. is 20000 across 4 sites, can the mailbox licenses be bought together and 'split' on individual installs of c380s OR they have to be bought separately for each c380.
    2.) If upgrading from the existing ESAs to new, can the licenses be imported from the existing c160s (which will be decommissioned) and exported to the new ESAs?

    1) each hardware appliance is licensed separately.  You'll need to work with account team/reseller to provide the #/size license as appropriate.
    2) If upgrading - yes, you'll just need to transfer the existing "as-is" license from the serial number of the existing appliance to the serial number of the newly purchased appliance.  Should be fairly exact to the RMA steps provided in the following article:
    http://www.cisco.com/c/en/us/support/docs/security/email-security-appliance/118000-technote-esa-00.html
    I hope this helps!
    -Robert
    (*If you have received the answer to your original question, and found this helpful/correct - please mark the question as answered, and be sure to leave a rating to reflect!)

  • License for CUCME on router and phones

                       We purchased a cisco 2911 voice router with CUCME 25 user license and now we want to but the cisco voip phones. My question is - do we need to buy the phones with their individual CUCME licenses or not? the voip phones are cisco 6945.

    This is often asked, if you search the forum you will find many threads on the subject.

  • Basic setup for Cisco RV325 router

    I am having problem with the basic setup of RV325 router.
    Example:
    STEP 1 Connect a PC to a numbered LAN port on the device. If the PC is configured to 
    become a DHCP client, an IP address in the 192.168.1.x range is assigned to the 
    PC. 
    Which LAN port does it meant?
    I tried the router connection on different LAN ports to a PC but the browser would not launch anything at  192.168.1.1. 
    Can anyone help?
    Thank you.

    Hello,
    It sounds like you are trying to access the web interface of your router so you can configure it.  First of all, I'll go over the ports of the router with you.
    The last port of each row (on the right side) of the device is for the WAN (Wide Area Network) that's designated for where you connect to your ISP (Internet Service Provider).  Most likely, you will connect your modem to one of those ports.  Any ports to the left of those are your LAN ports (Local) where you can connect your PC.  
    Once you connect to one of those ports, your PC should get an IP address.  If you are unable to get to the web interface of the router, you will want to confirm your IP address and default gateway (which is the IP address of the router).
    This can be done in Windows by:
    Select Start > Run. Type command or CMD into the dialog box, then click OK.
    In the resulting command line window, type ipconfig.
    C:\>ipconfig
    You will see something similar to this resulting output:
    Ethernet adapter Local Area Connection:
    Connection-specific DNS Suffix . :
    Description . . . . . . . . . . . : 3Com EtherLink 10/100 PCI For Complete PC Management NIC (3C905C-TX)
    Physical Address. . . . . . . . . : 00-01-03-AB-0E-6P
    DHCP Enabled. . . . . . . . . . . : Yes 
    Autoconfiguration Enabled . . . . : Yes 
    IP Address. . . . . . . . . . . . : 192.168.1.10
    Subnet Mask . . . . . . . . . . . : 255.255.255.0
    Default Gateway . . . . . . . . . : 192.168.1.1
    This will give you 3 key pieces of information you will want to verify.  First, you want to see that your network adapter is set to DHCP.  It should say yes next to it.  Second, your IP address needs start with 192.168.1.x
    In this example, it is 192.168.1.10, which is fine.  
    Lastly, your default gateway should be preset to 192.168.1.1.  If it is not, write that number down and try to access that IP address in your browser.  
    Note: If your browser is just coming up blank, you may want to try a different browser.
    Hopefully you'll be able to get into your router at this point.  If not, please provide the output of your IP config statement so we can further troubleshoot your issue.

Maybe you are looking for