Continued problems while attempting reinstall

Some weeks ago after restarting my Mac Pro it would only boot to a blue screen with no login window. I have been able to start in safe mode and even work productively minus the the ability to use video, peripherals, audio, and my font collection. I have tried several suggested solutions to this problem with no avail... disc utility as well as some commands entered in single-user mode to reset all preferences and application settings. No luck. Here's some info
Mac OS X
10.5.8
2 x 2.66 GHz Dual Core Intel Xeon
4 GB 667 MHz DDR2 FB-DIMM
500 GB HD 59 GB available space.
(second HD and DVD-RW have been non functional for about a year.)
I need to perform a full reinstall but because my DVD drive is non functional I am attempting to run the startup disc from an external DVD drive (HP dvd1040e). The drive works in safe mode and I can open it to see its contents. When I attempt to start from the disc (holding d during startup), it crashes into a gray screen with a restart warning during the boot process. I was able to remove the drive and restart again into safe mode. I was also able to boot into Apple Hardware Test from the disc and run it with no problems found.
I have backed up all of my files onto another external drive so I am prepared to wipe the HD and do a completely clean reinstall. I have never actually done a reinstall on a Mac so I don't know what I can do to remedy this somehow. Is there another technique to starting from and external DVD drive? Is it worth downloading the OS X install files to a flash drive or external hard drive to try from there? Things seem to get worse at every turn, any help I could get with this would be so greatly appreciated!
My nearest Apple store is over 2 hours away, I could go if I absolutely needed to but I would like to avoid it at all costs.

Update: I have made progress in that I was able to boot to the OS X Leopard install disc. The internal and external hard drives show up on the Select a Destination screen. The external drive shows the following warning: 'You cannot install Mac OS X on this volume. To enable installation on this volume open Disk Utility and repartition the disk as 'GUID Partition Table'. Note: You will lose data on this disk by repartitioning it.' This is not an option as all of my documents are backed up on that drive.
I was actually able to perform an 'Erase and Install' on my internal HDD with the Leopard disk. However, when the install completed and restarted, it simply booted into the solid blue screen. Same problem I've had all along! I can still boot into safe mode, and it is a clean reinstall. Now OS X doesn't even see my Airport card anymore. I have physically removed the non functional internal optical drive and 2nd HDD so I know that they are not the issue.
Does this mean that the issue is in firmware or something? I've accomplished a clean reinstall and the same problem is still there! What could it possibly be?

Similar Messages

Problem while attempting to install After Effect CS6 Trial.

Attempting to install After Effect CS6 Trial.
Receiving this error after 2% of the installation is complete....
Exit Code: 34
-------------------------------------- Summary --------------------------------------
- 1 fatal error(s), 0 error(s), 0 warning(s)
FATAL: Payload '{A189C479-C7CD-4E08-8CCF-D999B68C0C71} Camera Profiles Installer_6.3_AdobeCameraRawProfile6.0All 6.0.98.0' information not found in Media_db.
Do I need to re-download? Is there a funky setting on my system?
Looked in the forum and used the Adobe Support Advisor. It sent me to log files to look around and all I see is the same info.
Any help would be appreciated!
Thanks!

Unistall any ACR Betas on your system you may have used. Also simply run the Creative Suite Cleaner Tool and reinstall everything Adobe.
Mylenium

I am having a weird problem while attempting to re-install iTunes, is there anyone who can help?

Its kind of an odd problem, never happened to me before, but my old iTunes was very outdated because my updater was not working, and today having to actually use iTunes but it was very outdated, I read on the apple support site that the only way to update my version was to delete and re install.
Upon completely deleting iTunes and all other related software (following the steps given here:http://support.apple.com/kb/HT1923), and then installing the latest version of iTunes from the apple site, I still receive the very same error message about a quarter way through the installation saying 'Error, object already exists', and when I click ok it pops up a few more times until the iTunes install wizard says there was an installation error and to either finish or try again.
I really need to use iTunes asap for some important business so any help would be much appreciated.
Additional info:
Operating system is Windows 7
Computer is a Dell
Downloaded using Google Chrome

For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it, which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
The section Install missing components has advice on breaking down the iTunes installer into the individual .msi files which might prove useful if iTunes won't install normally.
tt2

I'm having problems with a message that says: An error occurred while Attempting to create the directory: C:/program files/itunes/cd configuarion

I know this is a long story, but I'll be damned if I'm not going to get the most specific help I can (as Apple seems to specialize in assuming user error for all its demonic software). I've never had issues with iTunes before (barring a "Connect to iTunes" snafu with my iPod Touch) -- and never, in fact, with Windows Vista, if you believe that -- but this is the most bizarre thing I've seen.
I recently downloaded the new iTunes v 9.0.3 as I am occasionally prompted to do whenever a new version comes out, and immediately I had problems. Access to the iTunes and Quicktime folders was mysteriously denied after the update, and after several hours of frustration, I was able to grant my own Administrative access to these two folders and installation went through. Thank God.
Then I bought some music. No problems -- downloaded just fine, along with a copy of Cinderella Man and the new episode of Smallville. Life was good for a few days.
Then I connected my iPod Touch to the computer. All of a sudden, Microsoft Windows informs me that the "Apple Mobile Device Service stopped working and was closed," with subtext, "A problem caused the application to stop working correctly. Windows will notify you if a solution is available."
Bullsh*t Windows can help me with anything from Apple.
So I've tried to get iTunes to work with me on this. I've come up against the infamous "iTunes could not connect to this iPhone because an unknown error occurred (OxE8000001)" message. My God, when does it ever end?
So I go into Control Panel > Administrative Tools > Services > Apple Mobile Device and start it back up... only to watch it stop again inexplicably moments later. Hmm... Restart. Stays on. Unplug the iPod and plug it back in. Apple Mobile Device Service stops again. Maybe it's the iPod Service itself. Hey, that one's not started! [Start] "Windows could not start the iPod Service service on Local Computer -- Error 5: Access is denied."
What the f*ck is it with this "Access denied" crap? I've never been denied access to even the most intimate functions, files and folders on my freaking computer before! What has Apple created!?
I thought, perhaps Apple Mobile Device software was somehow removed. Okay, let's redownload iTunes (aka Repair the program from the Programs and Features menu in the Control Panel -- same thing). Huh. "An error occurred while attempting to create directory C:\Program Files\iTunes\CD Configuration," and I can choose to Retry or Cancel. So, instinctively, I deleted the CD Configuration folder, assuming iTunes Setup would just recreate it.
Well, that didn't work now, did it? I deleted it and hit Retry, and it said, "The installer has insufficient priveleges to access the directory: C:\Program Files\iTunes\CD Configuration. Log on as administrator or contact your system administrator." Running the .exe file as an adminstrator changes NOTHING about this predicament.
So that's where it stands. No CD Configuration folder; full access to all files and folders involved; Apple Mobile Device Service still keeps going off for no reason; iPod Service still doesn't run; Repairing/Reinstalling iTunes, Quicktime, Bonjour, etc. does nothing; and God (aka Steve Jobs, apparently) hates me.
. . . . . . . . . . . . Help me.

Hi there,
I would recommend taking a look at the troubleshooting steps found in the article below.
Trouble installing iTunes or QuickTime for Windows
http://support.apple.com/kb/ht1926
-Griff W.

Why is firefox continuously connecting while on a web page? The wheel is spinning every 10 seconds or so. I reinstalled firefox so I need help.

Firefox is continuously "connecting" while I am on the web. It does not matter what site I am on but it keeps connecting (wheel spinning) every 10 seconds or so. Like it is reloading the page. The page does not go away, but it is driving me crazy as it did not used to do this. I did download a free trial of WordPerfect, but it was not what I was looking for and deleted it. I also reinstalled Firefox, so I am not sure what is going on. Help Please! I have a Windows 7 Sony Vaio computer. I ran the virus check a couple of times and it came up okay.

It is possible that your security software (firewall, anti-virus) blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox and the plugin-container from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
See:
*https://support.mozilla.org/kb/Server+not+found
*https://support.mozilla.org/kb/Firewalls
*https://support.mozilla.org/kb/fix-problems-connecting-websites-after-updating

Computer sees 9530 but get "A problem occured while attempting to connect to Blackberry device" prompt

Running Windows 7 *64, just updated Backberry Desktop Software to 7.1
Computer sees the Storm 9530, Device Manager sees it, I can't get into the folders through My Computer, or when running Desktop Software I go to click on Music then itunes and I get this prompt
-"A problem occured while attempting to connect to Blackberry device" prompt.
I'm just trying to add music from my only computer to my phone.
Iv'e follwed the Tips for getting BlackBerry Desktop Manager to detect the BlackBerry smartphone!
On the step "ii. Under Universal Serial Bus Controllers, verify that the BlackBerry smartphone is found."
it is an Unkown Device with an exlamation
I Continue along the steps until I arive at "ix. Double-click on RimUsbNT.inf, click OK, and then click Next."
Once I hit OK I get Prompt"the folder you specified doesn't contain a compatible software driver for your device"
I'm at loss for ideas..
Thanks in advance for your help.
Solved!
Go to Solution.

Hello Dark0prince and welcome to the BlackBerry® Support Community Forums.
Sorry to hear you're having an issue connecting your BlackBerry® Storm™ 9530 smartphone to the BlackBerry® Desktop Software.
Download your device software from your mobile carrier (click here) and install it to your computer. This will update the drivers for your device.
If you have already installed the software and the drivers and the issue persists then it would be advised you contact your mobile network provider and ask for a ticket to be opened with RIM support to investigate this matter further.
Thanks!
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Why am I stuck in a "you are logged out" loop while attempting to reinstall Adobe Creative Cloud ?

Why am I stuck in a "you are logged out" loop while attempting to reinstall Adobe Creative Cloud (ACC)? I am able to log into the Creatrive cloud member portal.
What gives.
Also, I can change my password at the ACC portal.
When prompted to login during installation the loop begins. I enter my username and password hit enter - click whir - and the same prompt reappears.
No email is delivered (not in junk either) when I ask for info on reseting my password the only solution offered in the debilitating prompt.

Are you on a managed network? Please navigate to ~/Library/Application Support/Adobe/OOBE/opm.db and trash it. Launch CC desktop and try to sign in.
Enable user library: http://helpx.adobe.com/x-productkb/global/access-hidden-user-library-files.html.
Note: Please disable anti virus if installed and then try to sign in.
Regards,
Romit Sinha

When I open itunes to play content I've already purchased and while attempting to view trailers for movies in the itunes store, I receive a generic error message from windows, and I'm directed to reinstall the latest version of itunes. Not a fix. Help?

When I open itunes to play content I've already purchased and while attempting to view trailers for movies in the itunes store, I receive a generic error message from windows, and I'm directed to reinstall the latest version of itunes. Not a fix. Help?

after perusing other subjects with playback issues:
this is the fix:
-Launch Control Panel - Double click Quicktime, If you do not see quicktime, look on the top left side of control panel and switch to classic view. This will then allow you to see Quicktime.
-Now click the advanced tab and click on Safe Mode GDI Only, Apply, then ok.

I m having ipad 4 and after upgrading to ios7 I m facing continuously rebooting problem while switching between apps can any buddy help or facing same problem

I m having ipad 4 and after upgrading to ios7 I m facing continuously rebooting problem while switching between apps can any buddy help or facing same problem

Make sure you have the Latest Version of iTunes (v11) Installed on your computer
iTunes free download from www.itunes.com/download
1) Connect to iTunes on the computer you usually Sync with and Restore
http://support.apple.com/kb/HT1414
2) If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/ht4097
Note on Recovery Mode.
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
Once you have Recovered your Device...
Re-Sync your Content or Restore from the most Recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766
Note:
Also consider Deleting any Apps you have Purchased / Downloaded but you now never use..

I just want to reinstall windows 7. will i face any problem while syncing with new itunes, i just want to reinstall windows 7. will i face any problem while syncing with new itunes???

i just want to reinstall windows 7. will i face any problem while syncing with new itunes, i just want to reinstall windows 7. will i face any problem while syncing with new itunes???

Syncing to a new iTunes library or computer will erase your iPhone. Only if you back up your phone manually before syncing, you can restore your device from that backup again. A manual backup does not include the sync process.
Do this:
Disable autosync in iTunes, connect your phone to your new computer and right click on it in the device list and choose backup. iTunes will backup your iPhone without syncing.
Transfer your purchases the same way, choosing "transfer purchases" this time.
When you connect your phone for the first time, all media content will be erased. But you can restore your settings and app data from your manual backup afterwards.
Don't forget to set up at least one contact and event on your new computer to be able to merge calendars and contacts when you sync the iPhone for the first time.
Music is one way only, from the computer to your device, unless you bought the songs in itunes and transferred your purchases.
There is 3rd party software out there, but not supported by Apple, see this thread: http://discussions.apple.com/thread.jspa?threadID=2013615&tstart=0
About backups and what's saved: http://support.apple.com/kb/HT4946
How to back up and restore:http://support.apple.com/kb/HT1414
How to download apps for free again:http://support.apple.com/kb/HT2519
Saving other data is also described here. How to back up your data and set up as a new device
You can also back up iTunes and restore it on your new computer How to back up your media in iTunes ,but the iPhone will be erased anyway during the first sync.

Severe problem while starting Lenovo 3000 N200

Dear friends & experts,
I am using Lenovo 3000N200 0769BDG laptop. I have following problems while starting the system.
Recently my system was hacked against which I installed an Anti-Malware software. It showed that the system was free from any Malware.(But believe me, it is true that the system was hacked.). But each time on starting the system, a black and white window is being displayed which contains the following message:
We apologize for the inconvenience, but Windows didnot start successfully. A recent hardware or software change might have caused this.
If your computer stopped responding, restarted unexpectedly, or was automatically shut down to protect your files and folders, choose Last Known Good Configuration to revert to the most recent settings that worked.
If a previous startup attempt was interrupted due to a power failure or because the Power or Reset button was pressed , or if you aren't sure what caused the problem, choose Start Windows Normally.
Safe Mode
Safe Mode with Networking
Safe Mode with Command Prompt
Last Known Good Configuration (your most recent settings that worked)
Start Windows Normally
Use the up and down arrow keys to move the highlight to your choice.
Seconds until Windows starts:30.....1
After 30 seconds, the Windows logo is displayed immediately followed by a Blue screen which lasts for 1 second and the system restarts. I tried all the options listed above-- from Safe Mode to Start Windows Normally but the same problem recurrs. And the system doesn't shutdown until I press the power button.
I have a licensed version of Windows Xp SP3 as OS. I tried to repair the system using WinXP CD but I found the following message:
Setup did not find any hard disk drives installed in your computer.
Make sure any hard disk drives are powered on and properly connected to your computer, and that any disk-related hardware configuration is correct. This may involve running a manufacturer-supplied diagnostic or setup program.
Setup cannot continue. To quit Setup, press F3.
A point to be noted is that earlier, I removed the Rescue & Recovery from my system thinking that it might not be of much use and now, I lament for it.
When I press F3 the same window appeared and the same problem recurred.
I tried to access the files in my hard disk using Ubuntu CD and it was successful. I used Lenovo hardware quick test to check for any hardware faults, and my system passed all the tests.
I request you to help me in solving this problem so that I can continue my studies peacefully.
Thanking you,
With regards,
T.I. Kiran

First off, being "hacked" and having viruses/malware are two different things. Someone hacking your computer doesn't really mean you have a virus/malware, it means an actual person gained access to your computer remotely and did something to it.
More than likely you got a virus that corrupt your Windows System directory and/or registry. Anti-malware software won't necescarily detect all viruses, especially executable that run commands to simply delete files.
The blue screen you're seeing is what us technicians call the BSOD (blue screen of death), it's an indication that there is a direct corruption with the core files that Windows requires to function properly.
As an IT Technician, if this were one of my laptops or one of my end-users, I would simply reload it with a fresh copy of Windows XP. There's a possiblity that all data you had on the laptop is gone because if the Windows core files are corrupt/missing, then that could very well mean your system was wiped completely but the boot table is in tact, hence the fact that you even have the option to boot Windows XP.
One other option I would suggest is try to reinstall Windows XP. Sometimes if you have the right copy of the install, it will let you reinstall the Windows XP core files, leaving your programs, files and directories in tact.
Good luck.

Error detected while attempting to run job

Hi everyone,
One of my users tried to run a rule in Hyperion Planning 11.1.1.3 and an error occurred:   Error detected while attempting to run job
When I went to Essbase, I found that when I launched the rule an error appeared:
ERROR - 1006059 - Invalid block header: Illegal block type -- Please use the IBH Locate/Fix utilities to find/fix the IBH problem.
I read that it could be an issue related to corrupted blocks. I'm not familiar with MXL and I read that there are commands that I could run. Someody could provide me help?
Regards,

I have XCP files:
----- Exception Error Log Begin -----
Current Date & Time:   Thu Nov 07 13:31:38 2013
Process Type:          Application
Application Name:      HYPCOLAN
Database Name:         COSTS
Exception Log File:    c:\Hyperion\logs\essbase\app\HYPCOLAN\COSTS\log00001.xcp
Current Thread Id:     5940
Exception Code:        0xC0000005=Access Violation
Exception Flags:       0x00000000=Continuable
Exception Address:     0x603B569F
Exception Parameters: 2
Exception Parameter 0: 0x00000001=Write Violation
Exception Parameter 1: 0x57970000 (Virtual Address)
----- Machine Registers -----
General Registers:
   EAX=0x795D0E18 EBX=0x5796FFF8 ECX=0x57970038
   EDX=0x0DC0F6CC ESI=0x00000048 EDI=0xFD320000
Control Registers:
   CS =0x0000001B EIP=0x603B569F Flg=0x00010283
   SS =0x00000023 ESP=0x024ACBB0 EBP=0x024ACBCC
Segment Registers:
   DS =0x00000023 ES =0x00000023 FS =0x0000003B
   GS =0x00000000
Floating Point Registers:
   CWD=0xFFFF027F SWD=0xFFFF3920 TWD=0xFFFF3FFF
   EOF=0x603B5699 ESL=0x0505001B DOF=0x603E9B50
   DSL=0xFFFF0023 CRS=0x00000000
Register Area (Hex):
   00 B0 B0 3A F7 7C 1D 90 CE BF
   00 00 00 00 00 00 00 00 00 00
   00 00 00 00 00 00 00 00 00 00
   00 00 00 00 00 00 00 00 00 00
   00 00 00 00 00 00 00 00 00 00
   00 00 00 00 00 00 00 00 00 00
   00 00 00 00 FC 09 A0 95 26 40
   00 00 C0 C6 B2 2C 7B 91 28 40
Debug Registers:
   DR0=0x00000000 DR1=0x00000000 DR2=0x00000000
   DR3=0x00000000 DR6=0x00000000 DR7=0x00000000
----- Stack -----
Stack Trace:
    0: 0x603b569f ESSSVRD@adReqCurrencyTransBegin + 0x9c22f 0x00000000010cf0a4 0x000000000dc0f6cc 0x000000000dc0f378 0x000000004a25db00
    1: 0x603b6ba8 ESSSVRD@adReqCurrencyTransBegin + 0x9d738 0x00000000010cf0a4 0x000000000032af01 0x0000000000000004 0x000000000000198a
    2: 0x603bb76b ESSSVRD@adReqCurrencyTransBegin + 0xa22fb 0x00000000010cf0a4 0x000000004a25db00 0x000000000dc0f330 0x000000000da45d00
    3: 0x603bc2d1 ESSSVRD@adReqCurrencyTransBegin + 0xa2e61 0x00000000000003a8 0x00000000010cf0a4 0x000000004a25db00 0x00000000214e006c
    4: 0x603bc441 ESSSVRD@adReqCurrencyTransBegin + 0xa2fd1 0x000000004a25db00 0x00000000024ad2a8 0x00000000010cf0a4 0x0000000000000000
    5: 0x603bf614 ESSSVRD@adReqCurrencyTransBegin + 0xa61a4 0x00000000010cf0a4 0x000000000025db00 0x0000000000000000 0x00000000010cf0a4
    6: 0x6037dc5f ESSSVRD@adReqCurrencyTransBegin + 0x647ef 0x0000000000000002 0x0000000000000000 0x00000000010cf0a4 0x00000000024ad2a8
    7: 0x6037e28d ESSSVRD@adReqCurrencyTransBegin + 0x64e1d 0x00000000010cf0a4 0x00000000024ad2a8 0x0000000000000002 0x0000000000000000
    8: 0x60376993 ESSSVRD@adReqCurrencyTransBegin + 0x5d523 0x000000000013003a 0x0000000000000000 0x00000000010cf0a4 0x00000000004ad200
    9: 0x601c902e ESSSVRD@adCSCRConvFixMbrFromBitMap + 0x1115e 0x000000000000012c 0x00000000596ea148 0x0000000000000000 0x00000000024ad40c
   10: 0x601af5d2 ESSSVRD@adOdomInc + 0x3172 0x00000000010cf0a4 0x00000000010cc462 0x000000000dc99940 0x000000000dc48fd8
   11: 0x601af718 ESSSVRD@adOdomInc + 0x32b8 0x00000000010cf0a4 0x00000000010cc462 0x00000000588edfd8 0x0000000000000000
   12: 0x601b02c5 ESSSVRD@adOdomInc + 0x3e65 0x00000000010cf0a4 0x000000000dc2d540 0x00000000010cf0a4 0x00000000604d283d
   13: 0x6032eb72 ESSSVRD@adReqCurrencyTransBegin + 0x15702 0x00000000010cf0a4 0x000000000dc6a0a4 0x000000000dc6a008 0x00000000024af660
   14: 0x6032db25 ESSSVRD@adReqCurrencyTransBegin + 0x146b5 0x000000000dc6a0a4 0x000000000dc6a008 0x00000000024af660 0x00000000604cfbba
   15: 0x603320d8 ESSSVRD@adReqCurrencyTransBegin + 0x18c68 0x00000000010cf0a4 0x000000000000000d 0x00000000024af660 0x0000000000004650
   16: 0x602ed5ac ESSSVRD@adThreadRegister + 0x467c 0x00000000010cf0a4 0x0000000000004650 0x0000000000000000 0x0000000000000000
   17: 0x602eec17 ESSSVRD@adThreadRegister + 0x5ce7 0x00000000000cf0a4 0x0000000000000000 0x0000000000000000 0x00000000010cf0a4
   18: 0x77e6481f kernel32@GetModuleHandleA + 0xdf 0x0000000000000000 0x0000000000000000 0x0000000000000000 0x0000000000000000
----- Application-Wide Configuration -----
Server Name:
Application Name:      HYPCOLAN
Elapsed App Time:      00:21:23:39
Module Count:          16
Module 0:             0x00401000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSVR.EXE
Module 1:             0x60001000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSVRD.DLL
Module 2:             0x60B31000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSASOSM.DLL
Module 3:             0x60CA1000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSRPM.DLL
Module 4:             0x60DC1000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSAPINU.DLL
Module 5:             0x60E91000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSOTLSU.DLL
Module 6:             0x60F41000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSOTLNU.DLL
Module 7:             0x60F81000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSMTDNU.DLL
Module 8:             0x61031000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSOPGN.DLL
Module 9:             0x61061000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSHRU.DLL
Module 10:             0x61135430 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSUTLU.DLL
Module 11:             0x61151000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSDU.DLL
Module 12:             0x61171000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSGLOBU.DLL
Module 13:             0x61181000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSECU.DLL
Module 14:             0x61191000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSOBJIO.DLL
Module 15:             0x611A1000 = C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSDVRQ.DLL
----- Operating System Resources -----
System Date & Time:    Thu Nov 07 13:31:39 2013
Elapsed OS Time:       13:21:34:36
OS Name & Version:     Windows NT 5.02
CPU Count:             16
CPU Type:              Pentium
Correct System Memory information currently not available
Swap Flags:
   Enabled:            Y
   Disabled:           N
   File Found:         Y
   Denied:             N
Swap file(s):          c:\pagefile.sys
Correct Swap Space information currently not available
Total Drives:          6
Current Drive:         3
Drive 3:
   Drive Name:         C
   Volume Label:       Local Disk
   Drive Type:         Fixed
   File System:        NTFS
   Total Drive Space: 142689329 KB
   Free Drive Space:   71187620 KB
   Used Drive Space:   71501709 KB
Drive 4:
   Drive Name:         D
   Volume Label:       Drive_D
   Drive Type:         Fixed
   File System:        NTFS
   Total Drive Space: 292415096 KB
   Free Drive Space:   18586252 KB
   Used Drive Space:   273828844 KB
Drive 5:
   Drive Name:         E
   Volume Label:
   Drive Type:         Unknown
   File System:        Unknown
   Total Drive Space: 0 KB
   Free Drive Space:   0 KB
   Used Drive Space:   0 KB
Drive 6:
   Drive Name:         F
   Volume Label:
   Drive Type:         Unknown
   File System:        Unknown
   Total Drive Space: 0 KB
   Free Drive Space:   0 KB
   Used Drive Space:   0 KB
Drive 7:
   Drive Name:         G
   Volume Label:
   Drive Type:         Unknown
   File System:        Unknown
   Total Drive Space: 0 KB
   Free Drive Space:   0 KB
   Used Drive Space:   0 KB
Drive 21:
   Drive Name:         U
   Volume Label:
   Drive Type:         Unknown
   File System:        Unknown
   Total Drive Space: 0 KB
   Free Drive Space:   0 KB
   Used Drive Space:   0 KB
----- System-Wide Configuration -----
Elapsed Essbase Time: 00:21:23:39
Essbase Version:       11.1.1
Essbase Description:   ESB11.1.1.3.0B126
Network Type:          Windows Sockets
Environment Variable: ARBORPATH                 = c:\Hyperion\products\Essbase\EssbaseServer
Environment Variable: ARBORMSGPATH              = c:\Hyperion\products\Essbase\EssbaseServer\bin
Module Count:          16
Module 0:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSDU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 1:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSGLOBU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 2:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSUTLU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 3:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSECU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 4:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSOBJIO.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 5:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSOPGN.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 6:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSOTLSU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 7:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSHRU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 8:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSAPINU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 9:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSOTLNU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 10:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSRPM.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 11:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSMTDNU.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 12:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSASOSM.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 13:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSDVRQ.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 14:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSVRD.DLL
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
Module 15:
   Module Name:        C:\HYPERION\PRODUCTS\ESSBASE\ESSBASESERVER\BIN\ESSSVR.EXE
   Module Version:     11.1.1.1
   Module Description: ESB11.1.1.3.0B126.1
   Module Use Count:   2
----- ESSBASE.CFG Configuration Values -----
Configuration Value:   JvmModuleLocation         = c:\Hyperion\common\JRE\Sun\1.5.0\bin\client\jvm.dll
Configuration Value:   AuthenticationModule      = CSS
Configuration Value:   PORTINC                   = 3
Configuration Value:   DataErrorLimit            = 65000
Configuration Value:   CalcCacheHigh             = 1100000000
Configuration Value:   CalcCacheDefault          = 500000000
Configuration Value:   CalcCacheLow              = 30000000
Configuration Value:   CalcLockBlockHigh         = 4000000
Configuration Value:   CalcLockBlockDefault      = 900000
Configuration Value:   CalcLockBlockLow          = 400000
Configuration Value:   UpdateCalc                = False
Configuration Value:   NetDelay                  = 3000
Configuration Value:   NetRetryCount             = 1000
Configuration Value:   MultipleBitmapMemCheck    = True
Configuration Value:   ParCalcMultipleBitmapMemOpt = True
Configuration Value:   DYNCALCCACHEWAITFORBLK    = TRUE
Configuration Value:   DYNCALCCACHEBLKRELEASE    = TRUE
Configuration Value:   DYNCALCCACHEMAXSIZE       = 600M
Configuration Value:   DYNCALCCACHECOMPRBLKBUFSIZE = 400M
Configuration Value:   CalcLimitFormulaRecursion = TRUE;
Configuration Value:   AGENTPORT                 = 1423
Configuration Value:   SERVERPORTBEGIN           = 32768
Configuration Value:   SERVERPORTEND             = 33768
Configuration Value:   AGENTDESC                 = hypservice_1
----- Client Request Activity -----
Server Name:
Application Name:      HYPCOLAN
Total Request Threads: 20
Avail Request Threads: 19
Total Requests:        220
Average Requests:      111.000000
Weighted Average:      0.007431
Statistics Per Minute:
   Current Requests:   0
   Minimum Requests:   0.000000
   Maximum Requests:   111.000000
Thread Count:          20
Thread Id 3324:
   Request Name:        GetAttributeNameSpecs
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 4060:
   Request Name:        GetMbrInfo
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 1692:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 736:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 5288:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 784:
   Request Name:        OtlQueryMbrs
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 220:
   Request Name:        GetSelectedMbrInfo
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 4356:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 6100:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 5944:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 4880:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 1128:
   Request Name:        OtlQueryMbrs
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 5728:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 5960:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 1208:
   Request Name:        GetOtlUMC
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 5240:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 1768:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 3648:
   Request Name:        OtlQueryAttrib
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 1736:
   Request Name:        GetOtlInfo
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:33 2013
   End Time:            Thu Nov 07 13:31:33 2013
Thread Id 5940:
   Request Name:        MaxL: Execute
   Database Name:       COSTS
   User Name:           admin
   Start Time:          Thu Nov 07 13:31:38 2013
   End Time:            Pending
----- Exception Error Log End -----

Switch Executive with SCXI "an error occurred while attempting to access device"

I get "an error occurred while attempting to access device" when trying to validate or use the test panel for my current configuration:
PXI-1010 (PXI/SCXI combo chassis)
PXI-4060 in the PXI rightmost slot
SCXI-1129 in slot 1 of the SCXI portion
Clean install of all NI software (2012 DS1 developer suite) and a reset of MAX configuration data after not getting this resolved previously.
Because the SCXI-1129 is being controlled by the 4060 (legacy), I can't use DAQmx in NISE 3.5. So I'm stuck with IVI. I've configured everything in IVI so that I can at least add my device (SCXI_1129) into a new NISE virtual device. But when I go to validate or make a connection in the test panel within NISE, I get the above error.
Am I configuring something incorrectly?
Attachments:
max_report.zip ‏93 KB

Frank,
Thanks for continuing to look at this issue. Here are my responses to your questions.
1) You get an error when your driver setup string in in the General tab of your Driver Sessions is "1129/2-Wire Quad 4x16 Matrix"? Are you using a
PXI-4060 in the right-most slot of a combo chassis. If you're using a DAQmx device, it's a whole different ball game. If you're not using a PXI-1010
combo chassis, it's a different story too.
2) I can't seem to find a way to cleanly export my IVI configuration files. Even the VI you wrote (Programmatically Export All Virtual Devices & IVI
Configurations for NI Switch Executive) didn't copy the IviConfigurationStore files. So I manually copied them over and attached them. When I create
my driver session, I type 3 things: the topology ("1129/2-Wire Quad 4x16 Matrix") in the driver setup string, "SCXI-1129" and "SCXI1::1" in the
hardware tab (It would be "SCXI0::1" if the dip switches on the PXI-1010 were set to address 0, which is the default), and niSwitch in the software
tab for the software module.
3) The error I'm getting is the name of the post. "An error occurred while attempting to access device". It get this when validating my NISE virtual
device when simulation is not checked. It's also peachy-keen for me when I simulate.
4) See the screenshot.
5) Production line down is par for the course for this lab due to how many people have messed with this station in an effort to bandage it over the
years to keep product flowing. Long story, but there has one problem after another on this machine for a while with no owner. I'm now responsible for the automated tests on it. I'm adding new devices because I'm essentially starting from scratch so I know what's going on and can trust it. But apparently I'm either getting the same error they had before or it's a new one. I suspect it's the same one but it "used to work". I had another coworking here yesterday and he opened a phone SR, gave the information, and was told they'd get back to him. I haven't heard anything yet.
Attachments:
IVI export.zip ‏34 KB
SCXI-1129 adding to NISE.JPG ‏36 KB

I installed Lightroom 5.6 on Mac, when starting I receive an error message "An error occurred while attempting to change modules"

I installed Lightroom 5.6 (full version, not trial) on Mac, when starting I receive an error message "An error occurred while attempting to change modules".
I tried removing it and reinstalling but the same error comes up.
Anybody have any recommendations?

A forum thread from 3 years ago talking about LR 1.x which had this problem seems to need permissions fixed or new folders created with the corrected permissions. You might try doing a repair permissions for your user and/or run LR as an administrator user. I am a PC person so cannot tell you exactly how to do that.
https://forums.adobe.com/message/1457020

T60 - Error while attempting to read the boot configuration data

Hello,
My wife just got an IBM-certified "pre-owned" T60 (type 2007 66U) running XP a few days ago. I updated all the drivers & patches and handed it over to her in good working order.
This morning when she turned it on, she encountered a message from the Windows Boot Manager:
Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
1) Insert your Windows installation disc
2) Language settings
3) Repair your computer
If you do not have this disc....
File: \Boot\BCD
Status: 0xc000000f
Info: An error occurred while attempting to read the boot configuration data
It almost goes without saying that we do not having our Windows installation disc as it was pre-installed by Lenovo. I've tried using F11 (after enabling it per other threads on this site) to access the recovery partition but it only takes me directly to the Windows Boot Manager error screen.
How do I go about repairing this BCD/Windows installation so we can continue our life?
Thanks...

You said that the computer is running Windows XP, but unless i'm wrong BCD (Boot Configuration Data) is a new feature starting with Windows Vista and also used by Windows 7. Windows XP use NTLDR (NT Loader) so if BCD is corrupted it sounds to me like someone tried to install Vista og Win7 on the computer or there might have been some leftovers from the previous owner. I don't think you have any other option but to use a Windows CD/DVD to fix this problem since you won't be able to boot from this computer. There might be some 3part utilities available that should be able to fix this, but i wouldn't know what that might be. My recommendation would be to get a Windows CD/DVD.
-gan

Continued problems while attempting reinstall

Similar Messages

Maybe you are looking for