Control unit problem with S750 speakers!

I just bought these things...
I installed everything as guided and specified, and I get sound for about 10 minutes perfectly without an issue. After, I flicked my sub "off", and back "on", and the control pod unit doesn't want to register when I press buttons on either the remote control or on the unit itself. I have no sound now and I'm very frustrated. Does anyone here think the control pod unit blew and I would need a replacement?

The second fuse is not inside the plug. If you look at the back of the subwoofer, with the power cable disconnected from both the wall outlet and the subwoofer itself, you will see the socket where the power cable goes into. On the bottom part of the socket there is a cartridge with an indentation at the top. The words "use only with 250V fuse are etched on the front of this catridge and below the cartridge there is a printed triangle with the symbols 3.5A 250V. To access the fuse you need to insert a flat screw driver into the indentation at the top of the cartridge then using the top edge of the power socket as a leverage point, gently push the cartridge away from the subwoofer back panel. The fuse is located inside the cartridge. This fuse, if faulty, should be replaced with a time-lag 3.5A 250V fuse. But your fuse is ok because the green light on your subwoofer turns on.

Similar Messages

  • Problem with rear speakers!

    I bought new Sound Blaster X-Fi Xtreme Gamer Card and I have problem. My rear speakers (DTT2200) don't work. They're connected well, I have newest audio driver and CMSS-3D is enabled. I tested speakers on Creative Control Console and only rear speakers don't work.5.1 speakers are enabled in control panel of WinXP.Please help,Albert.
    Message Edited by Albert_PL on 02-26-2007 12:10 PM

    Check its set to 5.1 everywhere, especially in the creative control (not 7.1 or stereo anywhere). Check your connections at both ends (sounds silly, but check theyre firmly in) and at the speakers too. Try hooking the rear connection up to the front output on the X-Fi to rule out a problem with the speakers. Check volumes everywhere, settings everywhere, etc. Things like this are normally just one small setting you have overlooked somewhere.

  • Problem with my speakers

    Hi,
    I am using HP ENVY m6-1225dx Notebook PC. It is little more than a year o;d and I never had any complaints with it.
    Since past few days, there is a problem with my speakers.
    However, when I use trouble shoot option, I am getting the following message 'Hardware Changes might not have been detected'. But immediately, the audio functions for few minutes and when it functions I am able to mute my system speakers. And few minutes later, when the audio stops functioning, I am not able to mute the speakers as well.
    Further, when I attempt to test the speakers I get the following message 'The device is being used by another application. Please close any devices that are playing audio to this device and then try again'. 
    I have attempted to install the drivers from the HP page, even then, the speakers worked only for few minutes.
    I am not sure, how do I go about it.
    Any help with respect to the above problem will be of great help to me.
    Pratheep
    This question was solved.
    View Solution.

    Hi,
    Try the following.
    Open windows Control Panel, open Windows Update, select 'View update history' in the left hand pane and then select 'Installed updates' link in the following window.
    Locate update KB2962407, right click it and select Uninstall.  When done, restart the notebook, open windows Control Panel, open Windows Update and select 'Check for updates'.  You'll see the update you just uninstalled being offered again - right click and select 'Hide Update'.
    After this you may or may not need to delete and reload the Audio driver - if you do, the procedure for using recovery manager to reinstall Software and Drivers is detailed in the relevant document on the link below.
    Recovery Manager - Windows 8.
    Recovery Manager - Windows 7
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Problem with internal speakers of MacBook Pro

    Hi,
    I wanted to know if anyone have experienced a problem with internal speakers of Mac Book Pro. In my MackBook the Internal speaker volume goes down automatically. I checked the System Preferences>Sound>Output , from there I check that it is in the middle ( Balance) However, the problem is still the exists. Just for testing I played an audio file and I moved the bar toward the right speaker it is the same and when I move toward the left speaker the whole sound goes off . Looks like one speaker stops working completely. Then I checked the Utilities > Audio MIDI Setup > Configure Speakers  from there I checked both left and right speakers and the channel frequency is fine. Still same issue.  I have no idea what is going on , I really need your suggestions to get this fixed.
    Thanks in advance.

    Try the following:
    http://support.apple.com/kb/HT1411 Apple Portables: Resetting the System Management Controller (SMC) and http://support.apple.com/kb/PH11243 OS X Mountain Lion: Reset your computer’s PRAM 
    Also, consider installing Boom

  • Having problems with internal speakers?

    Hello,
              I've recently encountered a problem with my speakers. There is also a red light coming out of the audio jack. I found out that many other people are having the same problems with newer Mac versions. I looked at many different discussions and some are wrong and some are right.  Here is a great idea for for making this work: 1) You can use a toothpick. From what I've read, it may work, but be very careful of what you're doing.  2) I've used this idea it works very well. Find a headphone or audio jack cord and plug it in the audio jack many times. What I did was plug it and unplug it very fast. What you're trying to do is confuse the computer for a bit then make it realize that there is nothing in the audio jack. This should work. If it doesn't (for whatever reason) do not use the extra money to get it fixed. If this isn't enough help look at some other discussions, it's how I solve my origional problem with my speakers.
                                                                                                                                                              Hope you find this helpful,
                                                                                                                                                                                                         Adam B.

    No, its too expensive for HP to plate the zif connectors with something that doesn't corrode....rolleyes.
    Thanks nice tutorial.
    The DV 6000 series was plagued with motherboard issues
    http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=ca&docname=c01087277

  • Problem with S750, subwoofer broken

    Sorry for my english, I don't know it well...
    I have major problem with my speakers system, subwoofer broken, I used them only for year, i heard strange noice while it was working and a bit later it was louder and louder... and now it's broken, who repairs speakers said that it's loud speaker broken, and they can't find same to insert new, so i don't know what to do... Nobody knows who can repair them. I can pay for it becouse warranty extended, if it's possible maybe i can buy new one? But it's too expensi've to buy new full speaker system.

    Jozh,
    This is not a support forum but rather a user-user interaction place. You can read the Announcement in red a the top of the board if in doubt. You can check with Customer Support with repair option if yours is faulty. By the way, did you mention you have extended warranty? If you did purchase extended warranty from retail vendor, you will need to check with them the extended warranty agreement.
    Jason
    Message Edited by Jason-CL on 06-16-2006 05:45 PM

  • Replacing g500 spekers with s750 speakers.

    hi i have the gigaworks g500 and the ddts 100 decoder.my friend has a set of gigaworks s750 speakers no sub.i am thinking of replacing the g500 speakers with the s750 speakers.is this safe to do would the tweeter work and would i notice any sound improvement has any done this thanks for any help.

    There is no real reason this shouldnt work. The satellites are the same impedance as far as i can tell, and their rms rating is similar.
    As for how it sounds its hard to say. The tweeter would work, and the mid unit is similar in both, so you should really get better high end sounds without affecting the mid. However the G500 satellites are ported which probably helps them perform better with lower frequencies, and you will probably notice this difference. Of course, the S750 speakers are rated to quite low frequencies anyway (for such sized satellites).
    I tried something similar with the DTT3500 amp/sub and S750 satellites. It did work, and you can clearly hear the difference. The only problem was the huge difference between the power ratings of the two - the amp doesnt much like driving those sats. Works fine aslong as you dont push it too loud though (it tends to just power off if overworked).

  • Problem with inbuilt speakers.... (Inter iMac Oviously :) )

    Hey all,
    well im having a problem with the inbuilt speakers. If i put some music on, volume, 2 bars (the keyboard controls) and mute it, i hear a buzzing noise like inbeat with the music im litsening to and i hear a slight buzz when its not on mute too,
    so can someone please help me??
    ty
    Pete

    Reset the SMC with this article. The SMC controls things like this and sometimes it causes problems.

  • Airtunes having problems with multiples speakers

    Airtunes works very well when I just have the music play through the remote speakers. But when I try to get it to play music through both my computer's speakers and the remote speakers at the same time, I get a message saying
    "An error occured while connecting to the remote speaker 'Bedroom.' An unknown error occured (-3256)."
    Then the music starts playing through my computer speakers but not the remote speakers.
    Any thoughts?

    Never mind, I found an article in the Apple support articles telling me how to solve this issue. It was a problem with my firewall settings.

  • My speakers on my mac don't work.the icon is dimmed and it won't let me play music or Skype.it tells me i have a problem with my speakers

    my speakers on my mac don't work.the icon of the speaker is dimmed and it won't let me play music or Skype.it tells me i have a problem with my speakers

    you may have flipped the micro switch inside the audio jack.  To rectify this issue take a toothpick an gently wiggle it inside your audio jack.

  • Bass problem with s750 + Live 24

    Bass is way, way too strong. I have it turned down to the lowest setting on the s750 control box.
    Recently upgraded my computer. Before, I had an Audigy 2zs and was able to fix the bass problem by going to system volume settings and reducing Bass in the Advanced Tone Controls section.
    Now I have a Shuttle SD3P computer with an integrated Li've! 24 bit sound system. The Bass controls that worked for me on my last system are now greyed out and inaccessible. The "Subwoofer" volume slider in Creative's volume settings program does not work (doesn't matter if you move it all the way to the top or bottom, bass still sounds the same).
    Please help. This is a serious problem (bass is so loud as to be painful - any games or music with even minimal amounts of bass are unplayable because of the problem).

    Can anyone suggest possible fixes?
    I would greatly appreciate it!

  • [Athlon64] Sound problem with new speakers, maybe related to soundcard on motherboard!

    I just bought new speakers to my PC, creative Inspire GD580, but no sound are comin from them! they worked, because on the remote u could press test and then a noise came from each speaker (its 5.1) but no sound in windows, (when u log in or out and that kind off stuff) and not when I play music or games. Whats he problem? they are exactly right plugged in in the computer and that kind of tuff sp thats not the problem. I wonder if it has anything to do with my motherboard because the sound card are on it, I dont use any seperatly sound card, I use the one on the motherboard, the motherboard is an MSI K8T NEO2 FIR, K8T800PRO, Socket-939 SATA, GbLAN, ATX, Raid, Firewire, AGP8X (sound exit : VIA VT8237 - 7.1 sorround sound.) Is this my problem? please help!             The Sound card i think its called Realtek AC'97 Audio for Via Audiocontroller, is that bad or good?
    Maybe thet just control the sound, i'm not sure its the sound cards name!

    Okay,
    the old speakers work fine, the new ones don't. So I don't think, that this is an issue of the mainboard.
    Please check if the speakers are really connected the right way. Also check "Audio devices" (sorry, don't know the equivalent in non-german Windows) in Control Panel, if speaker setup corresponds to your hardware. There is also a MSI- or realtek thingy in the control panel, you should have a look at the settings there, too.
    In BIOS there is not much to check. You can only enable or disable the onboard audio device. BIOS Version is shown on startup, it might be necessary to press the [pause] key in order to read the information.
    Michael

  • ITunes 10.6.3 problem with multiple speakers

    Running iTunes 10.6.3 on new MacBook Air.
    When I click on the Choose Speaker icon on the bottom of the window, I get a complete list of all available Airport Express stations that have speakers powered speakers plugged into them.
    When I choose Multiple Speakers, I only get a choice of this computer and Apple TV. None of the Airport Express Stations appear in the list for Multiple Speakers..
    Running same version of iTunes, and same OS on MacPro, and it works as expected.
    Do I need to do some type of network configuration on the air to get this to work?
    Thanks
    MtD

    I just tried this also on my iPad and it doesn't work there either. Although I can get into the account settings, when I try and change a subscription I get a big black rectangle in the middle of the screen and the iPad hangs until the screen login thing kicks in and I have to enter my pincode again.
    Maybe this is something to do with my AppleId, I can't actually believe this is a fundamental problem, although maybe  I am optimistic.

  • Problem with Rear Speakers (Inspire P5800)

    Hi,
    I have bought the Inspire P5800 Sound System but I have a problem. When I do a soundtest with the driver software all speakers work but when I want to listen to music with Musicmatch Jukebox I don't get any sound on the rear speakers. I have on board AC97 sound on a Gigabyte K8NS motherboard.
    Can anybody help me?
    Thanks!
    robertthronhill

    robertthronhill,
    That's normal as music are mostly in stereo and that's 2 channel only. Creative sound card have CMSS feature that upmix stereo to surround soundfield but since you are using onboard audio, you will have to check with your mainboard manufacturer if those audio card have similar feature also.
    Jason

  • Problem with USB speakers and new Mac Mini

    I have a USB sound system consisting of a pair of Harman Kardon soundsticks and a woofer from probably 10 years ago (bought and used originally with a Mac). I have tried driving it my new Mac Mini. It works fine for about a minute; then the music stops. Here's what I've tried to diagnose the problem:
    1. The problem does not occur when these speakers are driven from my Macbook Air (about 3 years old).
    2. The OS and iTunes software is up to date on both machines (10.9.5 and 12.0.1.26).
    3. It does not depend on which USB port I use on the Mac Mini.
    4. Using a port on a USB extender on the Mac Mini does not solve the problem.
    5. The iTunes Preference settings are the same on both machines.

    Sorry, no actual experience with USB Audio devices.
    I found this in the Pro forum, but the outlook doesn't seem good:
    http://discussions.apple.com/thread.jspa?messageID=1739084&#1739084

Maybe you are looking for