Convert PXIe-8135 controller to dual-boot Windows 7 and LabVIEW RT

Hello. I have a PXIe-8135 controller that originally was just running Windows 7. We are trying to convert it to a dual boot system to also run LabView Real Time. (There is host computer that will run LabVIEW 2014 with the RT module, and the controller will become a target).
I have created a FAT32 partition on the hard drive of the controller. Now, I’m trying to install the real-time OS with a USB flash drive made using the MAX utility, but I cannot boot using the USB drive for some reason. I keep getting the message “waiting for USB device to initialize”.
In BIOS, legacy USB support is [ENABLED] and boot configuration is set to [Windows/other OS]. I’ve tried removing the drive, waiting, and reinserting. I’ve tried two different USB drives (both 8 GB, different brands).
I’m not sure what to do next. Apart from the USB boot issue, is converting the PXIe-8135 even possible? I read about SATA/PATA hard drive issues with older controllers, but I don't know about this one.
Thanks, in advance, for your help!
-Jeff
Solved!
Go to Solution.

Per Siana's licensing comment, more information on purchasing a deployment license if you do not have one for this target can be found here.
The RT Utility USB key is used to set up non-NI hardware with LabVIEW Real-Time, but you should not need it in this situation to convert to dual-boot (*). Try this:
1. Since you already have a FAT32 partion created, go into BIOS setup and change to booting 'LabVIEW RT'.
2. The system will attempt to boot LabVIEW RT, see that the partition is empty, and switch over into LabVIEW RT Safe Mode. (this safemode is built into the firmware, which is why you don't really need the USB key).
3. The system should come up correctly and be detectable from MAX, and you can proceed with installing software.
4. To switch back to Windows, go back to BIOS setup and choose 'Windows/Other OS'
(*) One area where the USB key is helpful on a dual boot system is with formatting the disk. If you want to convert from FAT32 to Reliance on the partition designated for LabVIEW RT, the USB key lets you attempt to format a single parition and leave the rest of the disk untouched. If you format from MAX, the standard behavior is to format only one RT partition if found, but if not found, it will format the entire disk. Formatting from MAX on a dual boot system is consequently riskier and you could lose your Windows partition.

Similar Messages

Y500 dual boot windows 8 and fedora 19 problem

I bought a y500 two days ago and i wanted to dual boot windows 8 and fedora 19, so here's what i did
1. downloaded fedora 19 (x64) iso from the fedora website.
2.made a live USB using live usb creator.
4.opened disk management utility and shrunk the c drive (windows 8 was installed here) by 100 gb and kept the 100gb unallocated.
3. started the laptop with novo button, changed the bios config to boot from usb.
4.installed fedora from usb, selecting the 100gb unallocated memory for installation
5.restarted the laptop.
now the problem is fedora works perfectly but when i try to boot windows 8, the following error is shown.
windows failed to start
file:\BOOT\BCD
status: 0xc0000225
info:the boot configuration data for your PC is missing or contains errors.
i am guessing the fedora installation overwrote the boot files of windows and
i have not taken a backup. please help

hi,
I have a Y500 and I wanted to dualboot fedora 19 with windows 8, this proved to be unsuccessful. I had made a repair disk before the process (but not a set of recovery disks unfortunately >.< ). now I inserted the repair disk and selected the automatic repair option, it showed a message that auto recovery has failed. now when I pressed the NOVO button and selected the system recovery option, it does not go into the OKR menu but continues with the normal booting process. Can somebody guide me or give links where I can find step by step instructions to making OKR work and reset my laptop to factory settings? PLEASE help As Soon As Possible
NOTE: I did resize the windows 8 os partition but the recovery and the lenovo partition are still untouched

Dual Boot Windows 8 and Linux?

I have (UEFI System) an ASUS K55A UEFI motherboard laptop that came factory with Windows 8. I would like to install backtrack linux and Windows 8, but before I go screwing up my laptop, I want to see if this would be at all possible. I would use a virtual
machine, but I need Backtrack Linux on a physical machine for testing purposes as I am taking a course in computer forensics, and I want to test cracking my home wi-fi. My processor is an Intel Core i5 2.5 ghz with a 500 GB HDD and 8GB DDR3 RAM. Any insight
on this would be appreciated. Thank You.

Hi,
You can refer to this article to get detail information.
http://apcmag.com/how-to-dual-boot-windows-8-and-linux.htm
Niki Han
TechNet Community Support

[SOLVED] Dual boot windows 7 and arch Linux with seperate hard drives

Ok so I'm stuck trying to get my computer to dual boot windows 7 and arch. They are installed on different hard drives and I have grub 2 as the boot loader. I can't find any tutorials on how to do it with seperate hard drives I know how to do it if they are on the same hard drive. Also I want windows on the "first" hard drive how do I check to see which one it considers the first?
Last edited by bdawg (2012-09-21 23:15:37)

DSpider wrote:
drobole wrote:If you want to change it so that sda becomes sdb and sdb becomes sda, you should be able to do that in BIOS.
Not from the BIOS. He would need to physically open up the computer and switch the cables between them (or add another drive).
There's no actual performance increase in changing this order. Performance increase is when you have the partitions as close to the beginning of a HDD as possible, where the platters spin faster (basic mechanics, not to be confused with CD/DVD, which are being written from the inside-out to prevent errors after extended usage), and it especially doesn't apply to SSDs whatsoever.
You may be right about that. I remember I had to do this a while back but I probably switched the cables. It also messed up the drive mapping in Windows 98 if I remember correctly.

Dual booting Windows 8 and Arch Linux with UEFI

Hi all!
I'm trying to install Arch Linux on my computer where I already have Windows 8, and I'm getting a little stuck when it comes to the partitioning.
Following the beginner's guide and the method here: https://wiki.archlinux.org/index.php/Un … n_in_Linux for setting up the partitions properly, regarding UEFI. My problem is that when using cgdisk to set up a new EFI system partition (ef00), I get an error message when trying to write the partition table (just saying that something went wrong). I figure the problem is that I already have a partition like this (correct me if I'm wrong), but it really looks like it succeded (see info below). So my question is: How do I preceed to keep my Windows 8 installation happy, but installing Arch? Do I remove the old EFI system partition and create a new one, or is there some method that allows me to edit the already existing one, to allow me to dual boot Windows 8 and Arch?
My partition table now looks like this:
Part. # Size Partition Type Partition Name
1007KB free space
1 500MB Windows RE Basic data partition
2 300MB EFI System EFI system partition (this one was already present on my system)
3 128MB Microsoft reserved Microsoft reserved partition
4 63.5GB Microsoft basic data Basic data partition
8 512MB EFI System EFI System partition (this is the one I tried to create when I got the error message)
5 29.5GB Linux filesystem Arch (this is where I was going to put my Arch installation)
6 22GB Windows RE Basic data partition
7 1024MB Windows RE Basic data partition
615KB free space
Just for the record; I only created partition #8 and #5.
Any help is appreciated! And sorry for beeing a total noob, but I really suck at this.

sudo make sandwich wrote:If it is possible to share ESP between OSes, how do I do this (would it be sufficent to follow this section: https://wiki.archlinux.org/index.php/Beginners'_Guide#For_UEFI_motherboards)?
There's really very little to do to share an ESP between OSes. Most OS installers will auto-detect the ESP and use it. Problem solved. For Arch it may be a bit more effort just because Arch uses a more hands-on installation process, but I've only done a couple of Arch installations, and the last one was several months ago, so I don't recall the details clearly enough to comment.
And how big will the partition need to be? The beginner's guide says 512MB or higher.
I don't know what was in the mind of the author, but my guess is that's because that's roughly the cutoff point where mkdosfs starts creating FAT32 by default rather than FAT16. The ESP is officially supposed to be FAT32, not FAT16, although FAT16 usually works OK. It's also possible to create FAT32 on smaller partitions by using an explicit option to mkdosfs ("-F 32").
The optimal size of the ESP depends on the files stored on it. If you don't store your Linux kernels, something as small as 100MiB is usually adequate; but a few Linux kernels and their initrd files can consume twice that amount. My own recommendation is for the ESP to be 200-500MiB.
The only error message I got from cgdisk is "Problem saving data! Your partition table may be damaged!", however booting Windows again works fine. Parted did not complain about antything.
Use the "verify" function in cgdisk. That will reveal any problems with the data structures. If a verify turns up OK, then that means that cgdisk ran into some sort of disk problem. Running gdisk rather than cgdisk and using the gdisk "w" option (without making any changes) may produce a more helpful error message.

Dual boot Windows 7 and Arch from 2 seperate drives (UEFI)

Hello everyone, I've been working on installing Arch to a secondary hard drive for the past few hours, but I am trying to make sure I won't mess up my Windows 7 install. I have found several topics talking about dual booting Windows 7 and Arch, but not a whole lot on booting them from separate drives. My drives are currently setup as follows.
sda (120GB SSD for Windows 7)
sda1 (100MB System Reserved NTFS partition)
sda2 (Windows 7 install)
sdb (1TB HDD for Windows programs, files, etc)
sdb1 (1TB NTFS partition)
sdc (1TB HDD)
sdc1 (boot 512MB FAT32)
sdc2 (root 500MB ext4)
sdc3 (home 300GB ext4)
sdc4 (swap 10GB)
rest unallocated "free space"
I used Gparted to create the partitions. I ended up getting hung up on the "Create Filesystems" sections, specifically this line"
# mkfs.fat -F32 /dev/sdXY
Now that I am looking at it, I'm thinking the "Create Filesystems" section maybe isn't necessary because I've used Gparted?
If it isn't necessary, when I get to the "mount the EFI System Partition to /boot" section, would I simply use
# mount /dev/sdc1 /mnt/boot
instead of
# mount /dev/sdXY /mnt/boot ?
The way I had this setup with Ubuntu was 3 partitions on sdc (/, home, swap) and I set my PC to boot to the sdc drive on startup. The boot loader would then give me the option to boot into Ubuntu or Windows 7, and I never had to alter the sda or sdb drives at all. Is this possible through Arch? My thinking is that even if it isn't, I should still be able to enter the BIOS boot menu and select which drive to boot manually correct? That wouldn't be too big of a deal for me because I spend 90% of my time in Linux, and only use Windows for Photoshop and gaming occasionally.
Thanks for taking the time to read this. I would have just tested this out, but I am afraid of messing up my Windows install.

After several sleepless hours I had to give up and go to bed about 5 hours ago. The installation process went smoothly (or so I thought). I followed the tutorial closely and upon rebooting I was met with a blinking cursor. After some googling I found others who said I should press TAB, but nothing seemed to work.
I rebooted to the iso disk and found the "boot installed OS" option and noticed it said "Press TAB to edit". I then found the boot parameters and tried everything from hd0 0 to hd4 4. I believe I have Grub setup correctly because every option besides hd0 0 either says "Booting..." and then gets stuck, or says "That disk and partition combination does not exist". So yea, I think hd0 0 is the correct boot path, it just gets stuck with the blinking cursor.
silverhammermba wrote:
You have the right idea. You want to install a bootloader on sdc1 which will be able to boot both Arch and Windows.
Your best bet would be to use something like rEFInd. It has a "scanfor" option that should automatically detect your BIOS-configured Windows installation and add a boot option for it. Note that depending on your motherboard, you may have to switch to UEFI-only mode and Windows will be unbootable without the assistance of a UEFI program which is backwards compatible with BIOS (like rEFInd).
Thank you for the link. Considering I can't get into my install and the actual install only took about 30 minutes, I think I am going to just start from the beginning again with REFIndr. It seems much simpler. I only used Grub because I've used it before with Ubuntu, but my very limited knowledge is telling me Grub is probably the problem.
MoonSwan wrote:Just an idea: My bios has a "Boot-up Prompt" which I can invoke when it's POSTing by hitting F11. This brings me to a menu that allows me to choose which drive I want to boot up that day. I use it when Syslinux isn't working properly (Which is right now as a matter of fact ...) in order to boot Windows so I can do some SCII, for example. I, too, dual-boot but I have both OSes on different SSDs. So my 120GB Crucial SSD has Arch on it and the 240GB Kingston has Windows, SCII, Portable Apps, etc and nary the two shall meet. It makes dual-booting easier in the case of a corrupt OS or MBR or what-have-you. You may want to give your Bios a better look to see if you can do the F11 trick. It probably can and will usually tell you so at POST by printing that information on-screen along with your drives-detected and other messages (I hit Pause sometimes to read all the POST messages).
This is exactly what I was talking about doing when I mentioned:
My thinking is that even if it isn't, I should still be able to enter the BIOS boot menu and select which drive to boot manually correct?
That's good to know, because even if this next install doesn't work I think if I pull the other drives I should be able to get it working fairly easily.
Thanks again everyone.

Dual Boot Windows 7 and Arch with Shared NTFS partition.

Hi everyone,
I want to dual boot windows 7 and Arch Linux.
Here's the problem... my hard drive isn't the biggest. I want to store all my music, movies, pictures, and documents on partition that both linux and windows can access seamlessly.
I want the partition to be NTFS. -- (the programs that map an ext4 drive to Windows are trash).
Here's what I think I need.
30GB NTFS to Windows.
30GB ext4 to Arch Linux
The remainder (190ish GB) to Shared Data.
I don't want the swap partition because I have a SSD and 4GB of RAM.
What is the best way to setup my partitions? And is this even possible?
Thanks!

Not a problem. I would create:
First of four primary partitions for windows.
Second of four primary partitions for /boot
Third of four partitions is an extended partition encompassing all the space not used by the first two partitions.
Put everything else inside the extended partition.
Mine is a bit more complicated, but this should give you an idea:
ewaller@odin:~ 1005 %sudo fdisk -l /dev/sda
Password:
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x87b33479
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 121778159 60888056 7 HPFS/NTFS/exFAT
/dev/sda2 597366784 625135615 13884416 83 Linux
/dev/sda3 121778160 597366783 237794312 5 Extended
/dev/sda5 * 121778223 123770219 995998+ 83 Linux
/dev/sda6 123770283 131770589 4000153+ 82 Linux swap / Solaris
/dev/sda7 193213818 597360959 202073571 83 Linux
/dev/sda8 131781258 193213754 30716248+ 83 Linux
/dev/sda9 131770591 131781194 5302 1 FAT12
Partition table entries are not in disk order
ewaller@odin:~ 1006 %
Partitions 1 and 2 are Primary partitions. Partition 3 is an extended partition. All the others live in partition 3

Dual boot windows 7 and solaris 11

Hi Friends,
Could some one please explain the steps to install dual boot windows 7 and solaris 11?
Thanks
Raja

Install Windows leaving a partition for Solaris. Install Solaris into the empty partition. Reboot. Use a partition manager if you need to shrink your current Windows Partition. GParted works great and is free.
alan

Dual Boot Windows 7 and solaris 10

Can some body guide me how to dual boot windows 7 and solaris 10?
Thanks

First partition your harddisk with at least 2 primary partitions, one for windows and the other for solaris if you only have one harddisk. It would be a good idea to create an additional small boot partition as the first partition as well if you intend on using an independent boot loader but it really depends on what your machine is capable of. For example, if you have multiple harddisk and your BIOS supports it, then you could just install each OS onto its own harddisk and use the BIOS function to disable/boot off specific harddisk. Otherwise, if you only have one harddisk and created multiple partitions, install windows7 first followed by solaris10, obviously installing into different partitions. If you have created a boot partition, then you can install the boot loader into that dedicated partition.

Re: Tecra S11 - Dual boot Windows 7 and XP

I have installed Windows 7 (from the hidden recovery section of the hardrive) on my new Tecra S11. I would like to know whether I can use the Windows XP
recovery media provided by Toshiba to create a dual boot Windows 7/Windows XP rather than reverting to XP?

You can create dual boot but not using two recovery images. Recovery image can be used for first OS installation. You cannot define on which partition the recovery image will be installed. It will always be installed on first partition.
I recommend you to do follow:
-at first install WXP using original Toshiba recovery disc
-Windows 7 install using Microsoft installation disc
I have done the same on my Satellite A300.

Running Dual boot windows 8 and win 7 pro with xp mode installed!! I love it!!

It took over 2 days to figure out how to adjust the bios to get my win 7 pro DVD to boot and install dual boot on this GREAT MACHINE!!
Step 1: using diskmgmt.msc you have to shring the C partition. I shrunk it so I had 80GB remaining as unallocated space.
Step 2: You have to enter the machine Bios adn set the BIOS to Both and UEFI as first
Step 3: Connect your usb dvd
Step 4: Put your win 7 pro dvd in the usb dvd drive
Step 5: Reboot your machine and when it starts press F12 to get the boot menu and select the usb dvd drive then press enter
The machine restarts
Message on screen says press a key to boot from cd/dvd
Press space and it boots up the win 7 pro DVD
After files copy and load the setup screen asks to accept the agreement and where to install win 7
BE SURE TO SELECT THE 80GB location
Then follow thru the win 7 prompts to load it.
When the machine restarts you will see a dual boot screen with Windows 7 on top as first selection and Windows 8 below it as 2nd selection.
Make sure to hit enter with windows 7 selected
The win 7 installation completes.
You will see many items with drivers not installed dont fret.
You can load most of the drivers by highlighting the device in control panel/device manager and pick update driver then select BROWSE for DRIVER and be sure to put in drive D:\ which is now the windows 8 drive and hit search.
Many of the windows 8 drivers installed with no issue.
The Realtek driver was an exception .. goto to the lenovo site and pick the x100e tablet and download the LAN driver from there about (4MB). Copy it to flash drive and install it in win 7 from the .exe file. The driver for LAN will install sucessfully. The version of the driver is 7.46 something the 7.11 versions do not workl.
I have only 3 drivers that I could not find - 2 list as unknown and are related to ACPI or power management and 1 lists as USB controller but all the USB stuff works without it.
Be sure to either shutdown the system or sign out of win 8 when your done so you get the dual boot menu. If you shutdown while logged into win 8 the next time you start up it will go right to win 8 until you signout and restart.
Just to let you know an easy way to shutdown is go to the desktop and press ALT + FN + F4 and a shutdown menu comes up on the desktop.
Once win 7 pro is installed you can download the XP mode free from Microsoft and install it.
This is of course AFTER you have ACTIVATED WINDOWS 7 ONLINE with YOUR ACTIVATION KEY(you supply).
ENJOY! This is the BEST machine I ever had!

It's been many, many years since I don't do dual boot anymore. Don't find the reason to do it, either. Different kinds of virtualization should be enough. Anyway...
dfw1417 wrote:
It took over 2 days to figure out how to adjust the bios to get my win 7 pro DVD to boot and install dual boot on this GREAT MACHINE!!
ENJOY! This is the BEST machine I ever had!
WHICH machine?
Cheers.
If I helped you, please give me some kudos! ^^

Dual Booting Windows 7 and Linux on a IdealPad Y580

Okay, I am a gradaute student and need to have linux dual booted with windows 7 on my y580. It currently has windows 7 on it. However, it already has four primary partitions.
C:/ Windows OS
A hidden OEM
D:/Lenovo
And a boot system drive.
Is there anyway to convert one of thse drives into an extended partition ? HowCan I delete one of the partitions ? did you guys get your dual boots to work in this case. Please list step by step if possible.

Hello and welcome,
You can probably finagle the partitions to allow for dual boot: copy the contents of D: to C: and delete D:, for instance. Speculating, since I don't have an IdeaPad to test on. You usually/probably/maybe lose the OneKey Recovery feature if you touch the partitions.
Others here on the Linux board may have been able to preserve OKR, but I'll leave that to them to describe since I haven't done it.
Long way of leading up to the question: is it sufficient to run Linux in a virtual machine, or as a WUBI install within windows? That keeps things simple and makes backups much easier as well.
Whatever you do, burn your recovery media first. Now.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Could use help dual booting windows 8 and ubuntu 13.04

I have a Lenovo G580 with windows 8 + Ubuntu 13.04 installed. I've been trying to get Dual-boot to work for the past few hours with no success. I've been following this guide. After setting up the partitions similar to the ones in the guide i downloaded easyBCD on windows 8. I then added Ubuntu 13.04 to the grub menu. When i restart my laptop i get the menu with lenovo recovery, windows 8, and Ubuntu(not Ubuntu 13.04 like i labeled) when clicking Ubuntu it says windows failed to load, insert media for recovery. I can't do anything to access Ubuntu at this point. I don't know what it is i'm doing wrong but could use some help. Below are some pictures of the process. I'll post any needed info that i may have forgotten. When choosing OS it's in uefi mode.
partitions
OS's

I have a Lenovo G580 with windows 8 + Ubuntu 13.04 installed. I've been trying to get Dual-boot to work for the past few hours with no success. I've been following this guide. After setting up the partitions similar to the ones in the guide i downloaded easyBCD on windows 8. I then added Ubuntu 13.04 to the grub menu. When i restart my laptop i get the menu with lenovo recovery, windows 8, and Ubuntu(not Ubuntu 13.04 like i labeled) when clicking Ubuntu it says windows failed to load, insert media for recovery. I can't do anything to access Ubuntu at this point. I don't know what it is i'm doing wrong but could use some help. Below are some pictures of the process. I'll post any needed info that i may have forgotten. When choosing OS it's in uefi mode.
partitions
OS's

Problem dual booting Windows 8 and windows 7 G480

I bought new laptop g480 and it comes with windows 8 single language and I want to dual boot it with windows 7 Ultimate. So I create one partition 50 Gig using Minitool Partition Wizard, after that I boot into USB device ( I've bootable Windows 7 USB and already disable secure boot in BIOS). The process went fine until it ask me where to install the windows, so I choose the partition 50 Gig I created before but I get this message "Windows cannot be installed to this disk of the GPT partition style". Help me guys how to solve this problem, I've searched solution for this but non of them seems working for me. Step by step will be good for me. I hope to get quick reply for this because I've this problem since 2 days ago and never get solution .
Thank you.
Solved!
Go to Solution.

Hi @CharlyAR
I tried your solution before I posted the message here but it didn't work but then I give it try again and I manage to install the Windows 7 ultimate. Now my pc dual boot with windows 7 and windows 8 (windows 8 is the main OS).
p.s. This is important guys, if u want to make windows 7 bootable USB by following the tutorial on youtube it wont work if you pc/laptops is pure GPT (UEFI) because most of them using MBR to make the tutorial thats why it look easy and works for them, it's almost same but there's "add-on" with GPT mode. You have to make the windows 7 bootable USB in GPT (UEFI) mode or it wont let you install. I couldn't find tutorial for this GPT mode on youtube.
All I do is search my old DVD-RW and erase it and I follow the tutorial here, same what @CharlyAR told me
http://www.youtube.com/watch?v=z7rRsQGew28

[Solved]dual boot windows 7 and arch linux

I have successfully installed arch linux dual boot with the original win7 on my PC. If I only use linux, then the system works well. The problem is that once I boot into Win7 then after reboot, the linux boot manager will stop working and the system always boots into windows automatically. My guess is Win7 automatically repair the boot loader.
My current solution is whenever I have finished using Windows, I'll boot with my linux USB installation, and run "gummiboot --path=/boot install". Afterwards, linux will work fine. But I believe there must be a better solution. Any help will be appreciated.
I have UEFI board by the way.
Last edited by jl2014 (2015-04-19 17:35:57)

Thanks for all your help first! I have tried Head_on_a_Stick's suggestions as the first step. Here is what I did. I have created :
$ cat /boot/loader/entries/windows.conf
title Windows
efi /EFI/hidden/Boot/bootmgfw.efi
The window boot path was :
/boot/EFI/Microsoft/Boot/bootmgfw.efi
and I changed
/boot/EFI/Microsoft
to
/boot/EFI/hidden
After reboot, I clicked 'Windows' option on the linux boot manager. Below are the error messages:
Windows failed to start.
File: \EFI\Microsoft/Boot/BCD
Info: An error occurred while attempting to read the boot configuration data.
Any idea what goes wrong?
I'll try other suggestions soon. Thanks all of you again.
Last edited by jl2014 (2015-04-19 00:03:33)

Convert PXIe-8135 controller to dual-boot Windows 7 and LabVIEW RT

Similar Messages

Maybe you are looking for