Converting Flat network to VLAN

Ok here is what I would recommend.You have your vlans setup, and the L3 mode set in the SG300 right?If so you will specify an IP address for the L3 router's interface on each vlan. For the sake of discussion lets say you have your business lan on VLAN 1, your guest network on vlan 100, and your servers on vlan 200 Your subnets are 172.16.1.0/24 for vlan 1, 172.16.100.0/24 for vlan 100 and 172.16.200.0/24 for vlan 200.The router's L3 interfaces will be 172.16.1.2 for vlan 1, 172.16.100.1 for vlan 100 and 172.16.200.1 for vlan 200.
[Sidebar] There are a couple of things I want to point out here. Your vlan ID can be any number between 1 and 4095. I will typically setup the vlan ID to match the 2nd or 3rd octet in the IP address. That makes the vlan to ip address human identifiable. The computers or switches don't care, but from a...

This is my first post after having read a lot and making little to no progress.I'm the SysAdmin at a small school and we are growing. My flat network is running out of IP addresses. So, given my limited budget, I switched my network backbone to a SG300-52 and am looking to VLAN setup my environment. I want to use Layer 3 switching and port by port VLAN.I've read several articles about how to do this with the SG300, but I just can't figure it out. I'm Sec+ certified, not CCNA so this is a little out of my league.
Right now my setup is one DHCP server (Win 2008 server) and a FiOS router serving as the gateway. I would like to convert to being able to split my ports to differing subnets and have routing in between them to alleviate my IP address issues. I will still only have one DHCP server (which multiple scopes) and that one gateway. I...
This topic first appeared in the Spiceworks Community

Similar Messages

Moving flat network to VLANs

I have a facility that is currently running a single class C network with a mix of hubs and switches. We are upgrading their infrastructure to be completely switched and implementing VLANS at the same time. I am planning to use a 3560 as the core switched attached to the router and have all the remote switches connected to it. The 3560 will support all my VLAN configuration stuff. I will have a VLAN for the user population, a management VLAN and a VLAN for some of the production machines. I am planning on keeping their existing class C for the user population to avoid have readdressing issues and split up a new address space for the rest.
My question concerns the link between the router and the switch. I am thinking a simple point to point network between the two and then use eigrp between them for routing. I am thinking that I can carve up the new space and have a portion for several point to points and then a portion for my management VLAN and finally a portion for the production machines.
I am used to everything havving its one Class C space just for simplicity but would hate to start that model since what I do here I want to apply to 30 other facilities. I figure this was each facility with be contained within two to four Class C and make the over all management and routing simplier.
Am I on the right track?? Recommendations??

Do you have a specific goal in mind by establishing separate VLANs? If not, it would not appear to harm anything by sticking with a single Class C space (/25 or /26 mask if you don't need it all) and not readdress at all. I would recommend moving to DHCP though. Painful at first but will simplify things (e.g., change management) a lot in the long term.
A single subnet wouldn't even need a dynamic routing protocol between the switch and router - just a static route. In fact - you don't even need to use the switch's routing image. Just let it act as a L2 switch only and set up your routing (again with only a static route - assuming you have only one WAN interface) on the router.
I'm a fan of simplicity - only add/turn on functions where you have a business need or can articulate added value. Especially if you have to do it over and over ("30 other facilities"). Make it so any tech can walk in and grasp what the setup is and how to troubleshoot it.
Hope this helps. Please rate helpful posts.

Flat network to Multiple VLANs

Hey,
We have about 30x 2950-T and 10x 3560 switches. I wish to break our flat network into about 10 VLANS using our 3550 as the VTP server and use Trunking between our switches. Do I put all of our switches into one VLAN seperately from our servers/workstations? Or is there a better way?
Also do the 2950T-24 support stacking as most of our switches are all daisy chained. Anyone have a good solution for me to better implement our switches?
I appreciate your help.
Cheers.

Its a good idea to have a management VLAN and have all the switches management IPs in that VLAN. Also, you will need a layer 3 switch such as a 3550/3560 to route between your 10 VLANs. The following page should help
http://www.cisco.com/warp/public/473/189.html
2950s do support gigastacking. You might want to refer to our best practices document(written for 6500/4500 but you can use it in for other switches too)
http://www.cisco.com/warp/public/473/185.html

Access Point configuration for flat network

We have recently aquired a remote location which has a pre-existing flat network (172.16.X.X/16). Before we are able to convert them over to our new IP scheme, they have a need to have wireless connectivity on site. We have 4 1142's which I need to configure for them. I have experience configuring WLC's and autonomous AP's for networks with multiple vlans but have never configured AP's for a flat, single subnet network. I need to configure them for either guest access (internet only) or corporate access to network resources with radius authentication. Do I configure a native vlan as I would for a typical multi vlan network? Do I configure the switch port as an access port as opposed to a trunk beacause of the lack of layer 3? I basically need a sample configuration for this situation.

since you are on flat network, you just need to configure the SSID, no need for subinterfaces. With the AP only servicing the one VLAN you can leave the port as an access port as well.
as they are on the only subnet, I wouldn't do a 'guest' SSID. I would go with just the corporate SSID with WPA2/AES/802.1x. So the config is exactly the same for the RADIUS server and the SSID, but greatly simplified since you don't have to sub-interface anything.
Steve

Converting flat file to XML using JMS

Hi,
I want to convert flat file to xml. My sender adapter is JMS,
Can anyone tell me that how to do that conversion ? Conversion is very simple.
Can we use File content conversion in JMS Sender ? any link or blog ? or any other idea to achieve this ?
Regards
Kulwinder

Hi,
The pdf has been removed from that link i suppose.
Anyways, go through the below help, everything that is there in "HowToConveModuleJMS.pdf" has been mentioned in this...
http://help.sap.com/saphelp_nw04/helpdata/en/24/4cad3baabd4737bab64d0201bc0c6c/content.htm
Hope it would surely help you.
You can go through the below link, for better understanding..
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/a05b2347-01e7-2910-ceac-c45577e574e0
Regards,
Swetha.
Edited by: Swetha Reddy on Feb 26, 2009 5:30 AM

How can i convert flat idoc to IDOC-xml

Hi all,
I want to convert flat idoc to Idoc-xml. Suggest some methods for that....
K.S Grewal

This is the sample idoc data which i have been provided. actually i dont have much knowledge abt structure of idocs. As i have to test my scenario hich is idoc to file, i need Idoc-xml format.
ISA00 00 01006922827PCE1 126155214895 0612211736U004000004633020P|GSRE006922827PCE16155214895200612211736463302X004010ST9440001W17F20061221018085336610001 398456 1*83209N1WHWarehouseG620920061221W0740EA*PO5500203183PL000010*1MT42PF5321D/37~N9KK0180853366000001N9PEUS1TWHSW1440~SE90001~ST9440002~W17F20061221018085336710001 398448 183209N1WHWarehouseG620920061221W0756EA*PO5500203182PL000010*1MT*42PF7421D/37N9KK0180853367000001~N9PEUS1TWHS~W1456SE90002ST9440003W17F20061221018085338810001 398446 1*83209N1WHWarehouseG620920061221W071EA*PO5500205659PL000010*1MT50PF9731D/37~N9KK0180853388000001N9PEUS1TWHSW141~SE90003~GE3463302~IEA1*000463302~

URGENT : Program to convert flat file to XML file.

Hello,
       Good Morning. I want an urgent program to convert a flat file seperated by '/' to an XML file format and store that in the the application server. If any one has done such a developement, could you please send me the code.
The flat file format is as below :
72/070414/114147/11973//100-//EA/00000000///04198//RRT0/RC23///////353825001511172/72/070414/123620/11973//1000//EA/00000000///04198//RRT0/RC23///////354762008125236/72/070414/125411/13814//1000//EA/00000000///04198//INV/ID06///////90000000002697/72/070414/140820/11973//1000//EA/00000000///04198//RRT0/RC23///////353057002479718/72/070414/145438/13814//1000//EA/00000000///04198//INV/ID06///////90000000002739/72/070414/145438/11973//1000-//EA/00000000///04198//INV/ID06///////353057002479718/72/070414/150008/13814//1000
It needs to be filtered by removing the '/' and also grouped based on two fields namely store number and transaction number. The sample XML output required is as below :
<?xml version="1.0" encoding="ISO-8859-1"?>
<MT_POLL07 xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="../MT_POLL07.xsd">
<MessageHeader>
    <File>
      <Name>C:/kai/perl/storemaster_home/stores/09100/inbound/POLL07.DOS</Name>
      <CreatedDate>Wed Feb 7 13:09:15 2007</CreatedDate>
      <TotalRecordNo>19</TotalRecordNo>
    </File>
</MessageHeader>
<Transaction>
    <TransactionHeader>
      <TRANSACTION>20070414001559</TRANSACTION>
      <STORE_NO>09100</STORE_NO>
      <BOFTTP>72</BOFTTP>
    </TransactionHeader>
    <Item>
      <BOFTDT>070414</BOFTDT>
      <BOFTTM>114147</BOFTTM>
      <BOFSKU>11973</BOFSKU>
      <BOFUPC></BOFUPC>
      <BOFQTY>100</BOFQTY>
      <BOFQTN>-</BOFQTN>
      <BOFCST>0</BOFCST>
      <BOFCSN>+</BOFCSN>
      <BOFUM>EA</BOFUM>
      <BOFHRF>00000000</BOFHRF>
      <BOFSRF></BOFSRF>
      <BOFVND></BOFVND>
      <BOFLOC>04198</BOFLOC>
      <BOFEQT></BOFEQT>
      <BOFEQN>+</BOFEQN>
      <BOFRTP>RRT0</BOFRTP>
      <BOFREA>RC23</BOFREA>
      <BOFCID></BOFCID>
      <BOFAUT></BOFAUT>
      <BOFCUR></BOFCUR>
      <BOFPTP></BOFPTP>
      <BOFUPT></BOFUPT>
      <BOFUMR></BOFUMR>
      <BOFSRN>353825001511172</BOFSRN>
      <GMNUMBER>1</GMNUMBER>
    </Item>
    <Item>
      <BOFTDT>070414</BOFTDT>
      <BOFTTM>123620</BOFTTM>
      <BOFSKU>11973</BOFSKU>
      <BOFUPC></BOFUPC>
      <BOFQTY>1000</BOFQTY>
      <BOFQTN>+</BOFQTN>
      <BOFCST>0</BOFCST>
      <BOFCSN>+</BOFCSN>
      <BOFUM>EA</BOFUM>
      <BOFHRF>00000000</BOFHRF>
      <BOFSRF></BOFSRF>
      <BOFVND></BOFVND>
      <BOFLOC>04198</BOFLOC>
      <BOFEQT></BOFEQT>
      <BOFEQN>+</BOFEQN>
      <BOFRTP>RRT0</BOFRTP>
      <BOFREA>RC23</BOFREA>
      <BOFCID></BOFCID>
      <BOFAUT></BOFAUT>
      <BOFCUR></BOFCUR>
      <BOFPTP></BOFPTP>
      <BOFUPT></BOFUPT>
      <BOFUMR></BOFUMR>
      <BOFSRN>354762008125236</BOFSRN>
      <GMNUMBER>2</GMNUMBER>
    </Item>
</Transaction>
</MT_POLL07>
Please send me the code : It is urgent. Thanks in advace. Points to be rewarded.

hi !
Check with this thread discuss the same
http://www.sap-img.com/abap/sample-xml-source-code-for-sap.htm
Flat file to XML
CONVERTION OF FLAT FILE TO XML : NO OUT PUT FOUND
Converting Idoc flat file representation to XML
how to convert flat file into IDOC-XML
Regds
Abhishek

Converting flat files to csv format

hi,
Iam converting flat files to csv format..the problem is that iam running a script for inserting values.while i run this script it works fine .but while i open this csv file the datas in the excel sheet is not coming in a single line that is for a particular record its moving to second line .there is a break for a single record.so there is a problem in conversion.can anything be done in it this to avoid the breaking of lines
thanks
Ratheesh

YOGenereally, you shouldn't convert from a lossy format AAC or MP3) to another lossy fomrat.
It's called loss because you lose information when you convert it.
If you only use these files on the computer and the iPod, I'd recommend AAC. Better quality at same bit rate as MP3.

How to convert Flat file(.txt) data to an Idoc format(ORDERS05)

Hi,
How to convert Flat file(.txt) data to an Idoc format(ORDERS05). If any FM does the same work please let me know.
thanks in advance,
Chand
Moderator message : Duplicate post locked. Read forum rules before posting.
Edited by: Vinod Kumar on Jul 26, 2011 11:11 AM

Hi,
For more information, please check this link.
http://sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/46759682-0401-0010-1791-bd1972bc0b8a
Have a look at the FM IDOC_XML_FROM_FILE. May be it helps...
Regards

Moving Toward Flat Networks

What exactly is meant by a flat network? Please read on before you give a quick answer.
I have some definite ideas, but I would love to hear other people's inputs, ideas and perceptions.
The   trend in the data center is to go in the direction of flat networks, which to me means that the multi-tiered architectural model can be collapsed into 2 layers. Juniper says they will collapse the data center into one tier: the Stratus project promises the equivalent of one gigantic logical switch.
So, the implication is that there will be a flattening of the network in 2 ways: first, in terms of physical layers of networking and secondly, in terms of creating one logical L2   domain that is horizontally expanded (across data centers, too), but   the redesigned L2 domain will not require STP, blocked uplinks, or   unknown unicast flooding.
I do require some clarification:
1.)   How exactly can the access and aggregation layers be flattened? If, for example, one can stack all the top of rack (accesss layer) switches to create a single virtual chassis and then do the same, or something similar, like VSS, to the aggregation layer, the result is that each layer will see the other layer as one switch. So, 10 access switches will look like 1 switch to the aggregation layer, and 2 aggregation layer switches will look like 1 switch to the access layer. This will allow one to create multi-chassis etherchannels that can expand the network horizontally, HOWEVER, there are still 2 layers of networking.
Does this make sense?
2.)   The value in spanning L2 domains across data centers in a services-oriented architecture is clear. It facilitates vMotion and vStorage and creates clusters of compute and storage resources, which can be leveraged for SAN replication, disaster recovery, cloud computing (IT/Software as a Service), and running active/active application services).
But does flattening the network mean that there will be one massive subnet that will be considered one broadcast domain? Albeit, unicast flooding and ARPs will have to be re-engineered to operate in this environment. This doesn't seem likely.
Any   thoughts?
Thanks

There are as many ways to skin the cat as you can dream up.
But clearly you cannot expect to change roles completely and have everything stay the same.. although the Mac should not need to start over.. TM should be able to have multiple setups where it recognises the different network layouts.. at least with ML it can do that. If you are using SL as per your profile.. no.. it has to be manually setup.
The first obvious solution is this.
Network B: Mac connects to LAN via a non-Apple wi-fi router; TC connects to Mac via ethernet cable
Do the same in network A.. Use the Mac by wireless for internet.. and backups to the TC connected directly by ethernet. Do not plug the TC into the network.
A variation on this.
You can even do it by ethernet.. simply have a switch and plug in both Mac and TC.. but use the TC on a different IP address. You can set statically double IP on the one ethernet port.
Even better plug in a USB drive and use that.. it will be faster, more stable, and more reliable for backups than the TC. Leave the TC in network A.

Implementing Vlan in a Flat network

Hi all,
Right now i have 6 2950 switches all in same subnet and connecting different deprtments.we have 2 routers and Pix 506e.Now I m told to create Vlans in a way where we can use some departments using one first ISP-Line and rest on 2nd ISP line.I want to kno that how can i use same Vlan name/group across the switches or do i have to re arrange cables from various departments and then creating vlans.?we have 2600 series router with 2 ILL.Can i use 1 switch in command mode and other switches connected to various departments as a member of 1st switch and VLan on first switch only? please provide me details on this.
Thanks in Advance..
Sid

When you create multiple vlans, you will need a router (or l3 device) to route between vlans. Since your switches are 2950s, they are layer 2 only. You can use the 2600 router for external inter vlan routing.
Vlans can span different switches if you use trunking between the switches. (802.1q or ISL - 2950 support only 802.1q) To facilitate ease of configuration of vlans in the database of each switch, you should utilise VTP. One switch will be the VTP server, while all others are clients. You create vlans in the VTP server and it will propagate the information automatically to all other VTP clients. Still you will need to log into each switch and associate the physical port to the appropriate vlan.
Check out some of these guides on,
VTP - http://www.cisco.com/en/US/products/hw/switches/ps628/products_configuration_guide_chapter09186a00800d84bf.html
Clustering - Helps in managing all switches in a cluster using one IP address
http://www.cisco.com/en/US/products/hw/switches/ps628/products_configuration_guide_chapter09186a00800d84b7.html
Trunking and Vlan configuration -
http://www.cisco.com/en/US/products/hw/switches/ps628/products_configuration_guide_chapter09186a00800d84be.html
External Inter vlan routing with a 2600 router
http://www.cisco.com/en/US/tech/tk389/tk390/technologies_configuration_example09186a00800949fd.shtml

1142 converted to LAP and VLANs

Hi,
I just converted AP 1142 to LAP using the image "c1140-rcvk9w8-tar.124-21a.JA2.tar".
The WLC is a 5500 with 2 NIC : one on 192.168.0/24, one on a specific vlan 10.20/16
The main management interface is on 192.168/24 but we defined as management the interface on the 10.20/16 network.
For the access points, we use ports on a native VLAN on 10.20/16 with other available VLANS which are used for the wlan networks
We have 1152 APs which work fine on this config but that needed to be registered on the 192.168/24 network, then we moved them in their VLAN 10/20/16 and they work fine.
We also have 1142 APs which have been upgraded to LAP. These AP do not work with our architecture.
They register correctly on the 192.168/24 network, but do not give access to the wlan VLANs. If they are moved in the 10.20/16 network, they don't register to the WLC (message : Timed out while waiting for ECHO repsonse from the AP). The AP do not get an IP.
is there a restriction with VALNs on these AP ? or is something false ?
Thanks,
Christophe

Stephen, leolaohoo thank you for your help and ideas
Here is the configuration (some details deleted or renamed), sorry I did not find the way to attach a file :
config location expiry tags 5 config local-auth method fast server-key encrypt 1 xxx xxx xx xxx config time ntp interval 3600 config time ntp server 1 192.168.0.200 config license boot auto config logging syslog level informational config logging syslog level 6 config logging syslog facility local1 config logging syslog host 192.168.0.200 config logging buffered alerts config logging buffered 1 config sysname wlc1 config interface address management 192.168.0.219 255.255.255.0 192.168.0.254 config interface port management 1 config interface address service-port 169.254.1.2 255.255.255.0 config interface address virtual 1.1.1.1 config interface address dynamic-interface guestwlan 192.168.1.253 255.255.255.0 192.168.1.254 config interface port guestwlan 1 config interface address dynamic-interface "vlan20 servers" 10.20.255.250 255.255.0.0 10.20.255.254 config interface port "vlan20 servers" 2 config interface ap-manager "vlan20 servers" enable config interface address dynamic-interface "vlan22 wlan test 1" 10.22.255.250 255.255.0.0 10.22.255.254 config interface port "vlan22 wlan test 1" 2 config interface address dynamic-interface "vlan23 wlan test 2" 10.23.255.250 255.255.0.0 10.23.255.254 config interface port "vlan23 wlan test 2" 2 config interface address dynamic-interface "vlan24 wlan test 3" 10.24.255.250 255.255.0.0 10.24.255.254 config interface port "vlan24 wlan test 3" 2 config interface address dynamic-interface "vlan25 wlan test 4" 10.25.255.250 255.255.0.0 10.25.255.254 config interface port "vlan25 wlan test 4" 2 config interface address dynamic-interface "vlan26 wlan test 6" 10.26.255.250 255.255.0.0 10.26.255.254 config interface port "vlan26 wlan test 6" 2 config interface address dynamic-interface "vlan27 wlan test 7" 10.27.255.250 255.255.0.0 10.27.255.254 config interface port "vlan27 wlan test 7" 2 config interface group interface add production guestwlan config interface group interface add production management config interface group create production config interface group interface add r&d "vlan22 wlan test 1" config interface group interface add r&d "vlan23 wlan test 2" config interface group interface add r&d "vlan24 wlan test 3" config interface group interface add r&d "vlan25 wlan test 4" config interface group interface add r&d "vlan26 wlan test 6" config interface group interface add r&d "vlan27 wlan test 7" config interface group create r&d config interface dhcp management primary 192.168.0.252 config interface dhcp service-port disable config interface vlan guestwlan 200 config interface create guestwlan 200 config interface dhcp dynamic-interface guestwlan primary 192.168.7.254 config interface vlan "vlan20 servers" 0 config interface create "vlan20 servers" 0 config interface dhcp dynamic-interface "vlan20 servers" primary 10.20.255.252 config interface vlan "vlan22 wlan test 1" 22 config interface create "vlan22 wlan test 1" 22 config interface dhcp dynamic-interface "vlan22 wlan test 1" primary 10.20.255.252 config interface vlan "vlan23 wlan test 2" 23 config interface create "vlan23 wlan test 2" 23 config interface dhcp dynamic-interface "vlan23 wlan test 2" primary 10.20.255.252 config interface vlan "vlan24 wlan test 3" 24 config interface create "vlan24 wlan test 3" 24 config interface dhcp dynamic-interface "vlan24 wlan test 3" primary 10.20.255.252 config interface vlan "vlan25 wlan test 4" 25 config interface create "vlan25 wlan test 4" 25 config interface dhcp dynamic-interface "vlan25 wlan test 4" primary 10.20.255.252 config interface vlan "vlan26 wlan test 6" 26 config interface create "vlan26 wlan test 6" 26 config interface dhcp dynamic-interface "vlan26 wlan test 6" primary 10.20.255.252 config interface vlan "vlan27 wlan test 7" 27 config interface create "vlan27 wlan test 7" 27 config interface dhcp dynamic-interface "vlan27 wlan test 7" primary 10.20.255.252 config country FR config mobility group domain FRzone config radius auth add encrypt 1 10.20.255.251 1812 password 1 xxxx config radius auth management 1 enable config radius auth retransmit-timeout 1 2 config radius auth network 1 enable config radius auth rfc3576 enable 1 config radius auth enable 1 config nmsp notification interval rssi rfid 2 config certificate generate webauth config database size 2048 config network master-base enable config network rf-network-name FRzone config rfid timeout 1200 config rfid status enable config rfid mobility pango disable config mgmtuser add encrypt admin 1 xxx 32 xxx read-write config mgmtuser add encrypt RWAdm 1 xxx 32 xxx read-write config advanced probe-limit 2 500 config advanced probe limit 2 500 config advanced 802.11a channel add 36 config advanced 802.11a channel add 40 config advanced 802.11a channel add 44 config advanced 802.11a channel add 48 config advanced 802.11a channel add 52 config advanced 802.11a channel add 56 config advanced 802.11a channel add 60 config advanced 802.11a channel add 64 config advanced 802.11a channel add 100 config advanced 802.11a channel add 104 config advanced 802.11a channel add 108 config advanced 802.11a channel add 112 config advanced 802.11a channel add 116 config advanced 802.11a channel add 120 config advanced 802.11a channel add 124 config advanced 802.11a channel add 128 config advanced 802.11a channel add 132 config advanced 802.11a channel add 136 config advanced 802.11a channel add 140 config advanced 802.11a channel cleanair-event enable config advanced 802.11a channel dca chan-width-11n 40 config advanced 802.11b channel add 1 config advanced 802.11b channel add 6 config advanced 802.11b channel add 11 config advanced 802.11b channel cleanair-event enable config advanced 802.11b tx-power-control-thresh -80 config wlan wmm allow 1 config wlan mfp client disable 1 config wlan wmm allow 2 config wlan mfp client disable 2 config wlan chd 3 disable config wlan wmm allow 3 config wlan mfp client enable 3 config wlan wmm allow 4 config wlan mfp client enable 4 config wlan wmm allow 5 config wlan mfp client enable 5 config wlan wmm allow 6 config wlan mfp client enable 6 config wlan wmm allow 7 config wlan mfp client enable 7 config wlan security wpa akm psk set-key hex encrypt 1 xxxconfig wlan security wpa akm psk enable 1 config wlan security wpa akm 802.1x disable 1 config wlan security wpa enable 1 config wlan security wpa akm psk set-key hex encrypt 1 xxxconfig wlan security wpa akm psk enable 2 config wlan security wpa akm 802.1x disable 2 config wlan security wpa enable 2 config wlan security wpa wpa2 disable 3 config wlan security wpa akm 802.1x disable 3 config wlan security wpa disable 3 config wlan security wpa wpa2 disable 4 config wlan security wpa akm psk set-key hex encrypt 1 xxxconfig wlan security wpa akm psk enable 4 config wlan security wpa akm 802.1x disable 4 config wlan security wpa wpa1 ciphers tkip enable 4 config wlan security wpa wpa1 enable 4 config wlan security wpa enable 4 config wlan security wpa wpa2 ciphers tkip enable 5 config wlan security wpa akm psk set-key hex encrypt 1 xxxconfig wlan security wpa akm psk enable 5 config wlan security wpa akm 802.1x disable 5 config wlan security wpa enable 5 config wlan security wpa akm psk set-key hex encrypt 1 xxxconfig wlan security wpa akm psk enable 6 config wlan security wpa akm 802.1x disable 6 config wlan security wpa enable 6 config wlan security wpa enable 7 config wlan exclusionlist 1 1 config wlan channel-scan defer-priority 6 enable 1 config wlan channel-scan defer-priority 5 enable 1 config wlan exclusionlist 2 2 config wlan exclusionlist 3 3 config wlan radius_server acct disable 3 config wlan radius_server auth disable 3 config wlan exclusionlist 4 4 config wlan radius_server acct disable 4 config wlan radius_server auth disable 4 config wlan exclusionlist 5 5 config wlan exclusionlist 6 6 config wlan exclusionlist 7 7 config wlan radius_server acct disable 7 config wlan radius_server auth add 7 1 config wlan broadcast-ssid enable 1 config wlan broadcast-ssid enable 2 config wlan broadcast-ssid enable 3 config wlan broadcast-ssid enable 4 config wlan broadcast-ssid enable 5 config wlan broadcast-ssid enable 6 config wlan broadcast-ssid enable 7 config wlan interface 1 management config wlan session-timeout 1 1800 config wlan interface 2 guestwlan config wlan session-timeout 2 1800 config wlan interface 3 "vlan27 wlan test 7" config wlan session-timeout 3 1800 config wlan interface 4 "vlan22 wlan test 1" config wlan session-timeout 4 1800 config wlan interface 5 "vlan23 wlan test 2" config wlan session-timeout 5 1800 config wlan interface 6 "vlan24 wlan test 3" config wlan session-timeout 6 1800 config wlan interface 7 "vlan25 wlan test 4" config wlan session-timeout 7 1800 config wlan create 1 linknet linknet config wlan create 2 guestwlan guestwlan config wlan create 3 open Open config wlan create 4 WPA-PSK-TKIP wptkip config wlan create 5 WPA2-PSK-TKIP wp2tkip config wlan create 6 WPA2-PSK-AES wp2aes config wlan create 7 WPA2-ENT-AES ent2 config wlan apgroup add R&D_Groupconfig wlan apgroup add ValidationNetwork "Validation Network" config wlan apgroup description ValidationNetwork "Validation Network" config wlan apgroup interface-mapping add ValidationNetwork 3 "vlan27 wlan test 7" config wlan apgroup interface-mapping add ValidationNetwork 7 "vlan25 wlan test 4" config wlan apgroup interface-mapping add ValidationNetwork 4 "vlan22 wlan test 1" config wlan apgroup interface-mapping add ValidationNetwork 5 "vlan23 wlan test 2" config wlan apgroup interface-mapping add ValidationNetwork 6 "vlan24 wlan test 3" config wlan apgroup add TestNetwork "Test Network" config wlan apgroup description TestNetwork "Test Network" config wlan apgroup interface-mapping add TestNetwork 4 "vlan22 wlan test 1" config wlan apgroup interface-mapping add TestNetwork 5 "vlan23 wlan test 2" config wlan apgroup interface-mapping add TestNetwork 6 "vlan24 wlan test 3" config wlan apgroup interface-mapping add TestNetwork 7 "vlan25 wifi test 4" config wlan qos 1 gold config wlan enable 2 config wlan qos 3 bronze config wlan radio 3 802.11bg config wlan enable 3 config wlan radio 4 802.11bg config wlan enable 4 config wlan radio 5 802.11bg config wlan enable 5 config wlan radio 6 802.11bg config wlan enable 6 config wlan enable 7 config dhcp proxy disable bootp-broadcast disable config 802.11a 11nsupport a-msdu tx priority config 802.11a rate disabled 6 config 802.11a rate disabled 9 config 802.11a rate supported 24 config 802.11a cleanair alarm device enable cont-tx config 802.11a cleanair alarm device enable jammer config 802.11a cleanair alarm device enable wimax-fixed config 802.11a cleanair alarm device enable dect-like config 802.11a cleanair alarm device enable tdd-tx config 802.11a cleanair alarm device enable video config 802.11a cleanair alarm device enable wimax-mobile config 802.11a cleanair alarm device enable 802.11-inv config 802.11a cleanair alarm device enable 802.11-nonstd config 802.11a cleanair alarm device enable superag config 802.11a cleanair alarm device enable canopy config 802.11a cleanair enable config 802.11a beamforming global enable config 802.11a cac voice sip bandwidth 64 sample-interval 20 config 802.11a cac voice sip codec g711 sample-interval 20 config 802.11b 11nsupport a-msdu tx priority config 802.11b rate supported 1 config 802.11b rate supported 2 config 802.11b rate disabled 6 config 802.11b rate disabled 9 config 802.11b cleanair alarm device enable jammer config 802.11b cleanair alarm device enable wimax-fixed config 802.11b cleanair alarm device enable dect-like config 802.11b cleanair alarm device enable video config 802.11b cleanair alarm device enable wimax-mobile config 802.11b cleanair alarm device enable superag config 802.11b cleanair alarm device enable 802.11-inv config 802.11b cleanair alarm device enable bt-link config 802.11b cleanair alarm device enable 802.15.4 config 802.11b cleanair alarm device enable 802.11-fh config 802.11b cleanair alarm device enable cont-tx config 802.11b cleanair alarm device enable tdd-tx config 802.11b cleanair alarm device enable msft-xbox config 802.11b cleanair alarm device enable bt-discovery config 802.11b cleanair alarm device enable 802.11-nonstd config 802.11b cleanair alarm device enable canopy config 802.11b cleanair alarm device enable mw-oven config 802.11b cleanair enable config 802.11b beamforming global enable config 802.11b cac voice sip bandwidth 64 sample-interval 20 config 802.11b cac voice sip codec g711 sample-interval 20 config 802.11b 11gsupport enable

How to convert flat file to XMl without key field value

Hi experts,
I have a input CSV Flat file which has got one HEADER line and Multiple Detail records.
I do not have any key field value to convert this FLAT file to XML using normal file content conversion.
Is there any module or Bean which can be used to convert this Flat File to XML.
Or any other remedy to overcome this problrm.
Thanks in advance.
Regards
Pradeep

Hi Saurabh,
Thanks for the reply.
Ur understanding is perfectly alright.Lets say my file is like below.
Account Number,Account Name,Currency,Unclear Balance,Account Balance010205000033,VAISHNAVI SALES CORPN,0.00,0.00,350000.00
010205000034,CHAKKA ENTERPRISES,0.00,-641350.47,8649.53
010205000035,SEHGAL TRADING COMPANY,338665.00,-220.00,461115.00
010205000036,SHUBH LAXMI AGENCIES,0.00,0.00,0.00
010205000037,EMPIRE AGENCIES,0.00,-245.11,0.00
010205000038,PIONEER AGENCIES,0.00,-696386.00,303614.00
I am not using the first line in the mappiing.
Are you saying that I need to ignore the first line while doing the conversion using Recordset OFFSET ?
Or do I need to make a single structure taking all the fields from header as well as details and while defining the structure I need to ignore the fields from header?
Please suggest.

Problem converting flat file to XML using JMS Adapter

I need to take an MQSeries message in a flat file format and convert it to XML before processing. I have configured the modules as described by the screenshot located here:
http://www.radesix.com/JMSConfig.jpg
The message is received however it isn't converting to XML. When I view the payload I get the message indicated by the screenshot located here:
http://www.radesix.com/JMSError.jpg
I am new to XI. Any ideas?

For simple plain conversion here is a config, which works in our system:
(left parameter key, right parameter value, module key always the same)
Transform.Class com.sap.aii.messaging.adapter.Conversion
TransformContentType text/xml;charset=utf-8
xml.conversionType SimplePlain2XML
xml.addHeaderLine 0
xml.processFieldNames fromConfiguration
xml.documentName SA02_Identnummer
xml.documentNamespace urn:mycompany-com:logistics:DFT:HWL
xml.structureTitle SA02_Identnummer_Satz
xml.fieldNames Satzart,Identnummer,Status
xml.fieldFixedLengths 2,10,3
Be aware, that you must delete all spaces in the config, especially when you copy and paste values.
For struct. conversion the entries are a little bit more complex.
Regards
Stefan

Converting flat file to XML

Hi
i just want to read flat file and convert it into xml but there are some problem ,it throws a ArrayIndexOutOfBoundException.Here is code.
import java.io.*;
import java.util.*;
class FlatXMLBudget {
public static void convert(List data, OutputStream out)
   throws IOException {
    Writer wout = new OutputStreamWriter(out, "UTF8");
    wout.write("<?xml version=\"1.0\"?>\r\n");
    wout.write("<Budget>\r\n");
    Iterator records = data.iterator();
    while (records.hasNext()) {
      wout.write(" <LineItem>\r\n");
      Map record = (Map) records.next();
      Set fields = record.entrySet();
      Iterator entries = fields.iterator();
      while (entries.hasNext()) {
        Map.Entry entry = (Map.Entry) entries.next();
        String name = (String) entry.getKey();
        String value = (String) entry.getValue();
        // some of the values contain ampersands and less than
        // signs that must be escaped
        //value = escapeText(value);
        wout.write("    <" + name + ">");
        wout.write(value);
        wout.write("</" + name + ">\r\n");
      wout.write(" </LineItem>\r\n");
    wout.write("</Budget>\r\n");
    wout.flush();
public static String escapeText(String s) {
    if (s.indexOf('&') != -1 || s.indexOf('<') != -1
     || s.indexOf('>') != -1) {
      StringBuffer result = new StringBuffer(s.length() + 4);
      for (int i = 0; i < s.length(); i++) {
        char c = s.charAt(i);
        if (c == '&') result.append("&");
        else if (c == '<') result.append("<");
        else if (c == '>') result.append(">");
        else result.append(c);
      return result.toString();
    else {
      return s;
public static void main(String[] args) {
    try {
        /*if(args.length<1)
        System.out.println("Usage: FlatXMLBudget infile outfile");
        return;
      InputStream in = new FileInputStream("d:\\file.txt");
      OutputStream out;
      int a=in.available();
      System.out.println("dd:"+a);
     /*if (args.length < 2) {
        out = System.out;
      else {*/
      List results = BudgetData.parse(in);
      int aa=results.size();
      System.out.println("dd:"+aa);
      out = new FileOutputStream("d:\\flattoxml.xml");
      convert(results, out);
    catch (IOException e) {
      System.err.println(e);
import java.io.*;
import java.util.*;
class BudgetData
public static List parse(InputStream src) throws IOException
         // The document as published by the OMB is encoded in Latin-1
         InputStreamReader isr = new InputStreamReader(src, "8859_1");
          BufferedReader in = new BufferedReader(isr);
          List records = new ArrayList();
          String lineItem;
          while ((lineItem = in.readLine()) != null)
             records.add(splitLine(lineItem));
        return records;
// the field names in order
public final static String[] keys = {
    "AgencyCode",
    "AgencyName",
    "BureauCode",
    "BureauName",
    "AccountCode",
    "AccountName",
    "TreasuryAgencyCode",
    "SubfunctionCode",
    "SubfunctionTitle",
    "BEACategory",
    "On-Off-BudgetIndicator",
    "FY1976", "TransitionQuarter", "FY1977", "FY1978", "FY1979",
    "FY1980", "FY1981", "FY1982", "FY1983", "FY1984", "FY1985",
    "FY1986", "FY1987", "FY1988", "FY1989", "FY1990", "FY1991",
    "FY1992", "FY1993", "FY1994", "FY1995", "FY1996", "FY1997",
    "FY1998", "FY1999", "FY2000", "FY2001", "FY2002", "FY2003",
    "FY2004", "FY2005", "FY2006"
private static Map splitLine(String record)
              record = record.trim();
                      int index = 1;
         Map result = new HashMap();
          for (int i = 1; i < keys.length; i++)
                  //find the next comma
                StringBuffer sb = new StringBuffer();
         char c;
           boolean inString = false;
           while (true)
             c = record.charAt(index);
             if (!inString && c == '"') inString = true;
             else if (inString && c == '"') inString = false;
             else if (!inString && c == ',') break;
             else sb.append(c);
             index++;
             if (index == record.length()) break;
      String s = sb.toString().trim();
      result.put(keys, s);
index++;
return result;
[output/error]
java.lang.StringIndexOutOfBoundsException: String index out of range: 71
at java.lang.String.charAt(String.java:444)
at BudgetData.splitLine(BudgetData.java:55)
at BudgetData.parse(BudgetData.java:16)
at FlatXMLBudget.main(FlatXMLBudget.java:79)
Exception in thread "main"
[output/error]
Can any one help me about this problem.

Off-by-one error.
In a String of length 70, for example, the characters are numbered from 0 to 69 in Java. Your program is written as if they were numbered from 1 to 70. So when you try to get #70, the exception occurs.
But if you want to use commas as a delimiter to break a string into substrings, it's much easier just to use the split() method of String than to write all that code you have there.

Converting Flat network to VLAN

Similar Messages

Maybe you are looking for