Converting old 1240AG setup to VMware WLC and setup question

I am working on trying to convert a 10+ year old deployment of Cisco 1240AG's into newer 2702e with Central controller via VMWare WLC 8.0. I have 4 sites which used to get DHCP via local request. I need to verify I have read correctly that my controller will need to have an IP address interface from each of the 4 sites in the DHCP vlan to be able to hand out IP address.
If the controller does require the IP address and interfaces, will the deployment of a backup WLC also need IP address in same range/Vlans or does it duplicate the settings of the Primary WLC?
Thanks ahead of time..

I need to verify I have read correctly that my controller will need to have an IP address interface from each of the 4 sites in the DHCP vlan to be able to hand out IP address.
If you are doing FlexConnect Central Switching on your WLAN for these sites, yes you should have dynamic interface assign to given subnet for each site. If you are doing FlexConnect local switching, then you do not want to have dynamic interface on given subnet (since traffic terminate locally at branch, so you can have a dummy interface on your WLC)
If the controller does require the IP address and interfaces, will the deployment of a backup WLC also need IP address in same range/Vlans or does it duplicate the settings of the Primary WLC?
If both primary & backup WLC will be online, then you cannot have same IP address, but can assign another IP on the given subnet to the secondary WLC dynamic interfaces (in case of FlexConnect Central switching)
HTH
Rasika
**** Pls rate all useful responses ****

Similar Messages

VMWare WLC setup question with dual VLAN at sites

Multisite in same town design.
VMWare WLC deployed at main site runs all remotes. (7 sites). Sites are around town and not on same campus. Flexconnect local deployed on Cisco 2702e APs. Setup for two SSID's, one for data connections, other for Cisco 7921g wireless phones. Each site has its own DHCP scope.
I tried to setup 2 seperate WLAN ID for each site however it does not like the reused SSID name. I do not want to have to setup 7 profiles on everyones laptop to go between buildings. Seen a post mentioning to use AP groups however the video link was removed so it went into a deadend.

Thanks Scott,
so what I had setup before was under each WLAN, was each the interfce pull down to the interface vlan. I have now changed that to management and setup AP groups, each with the site's data and voice vlan defined under the AP group WLAN tab. So instead of the multiple SSID listed, now only two are listed.
I will have to take my test AP out to one of the other sites and move it to one of the new AP groups but this appears to be working on my current group I am testing from.

Converting old analog video with maximum resoultion for archieving and eventual use in iMovie

There seems to be a lot of information on converting old (amatuer) analog video media to a digital format, and which one is best to preserve the maximum amount of data. I have already imported old VHS, analog 8, hi8, and dv into iMovie interations from iMovie 6 and forward. The later versions seem to convert the older files to their own format, I suspect, with a loss of data. I want to reimport the old media to create masters in the best digital format for eventual editing by iMovie 11, or whatever iMovie comes after that.
I have the following formats: VHS, super VHS, 8MM, Hi8, DV, and a memory card (from a camera which is not directly compatible with iMovie 11)
I have the following equimpent:
SONY dual deck VHS DVD. This allows me to convert VHS directly to DVD. I can later decode using Handbreak, and import etc. but it seems I would be losing quality.
SONY Digital 8 handicam. This will play analog tape and output a digital file. I do not know the quality of the output.
Canon VIXIA HFS100, HD camcorder. This uses memory cards. It is NOT compatible with iMovie 11, which I should have checked before I bought it. I have played around with the memory card and have been able to import video but, I do not know the quality, and I've forgotten how I did it.
MacBook Pro, about 4 years old, with a 2Ghz Intel core duo processor and 2GHz Ram. This is obviously not state of the art. I am willing to upgrade within the Mac family but I don't what to upgrade to for my purposes
Canopus ADVC 110. This as DV out via a firewire port, and a DV in/out. It also has svideo in, and composit in.
I have the following software:
iMovie 6, iMovie 9, and iMovie 11. I am fairly comfortable with each version.
Final Cut Express, circa 2006. I would have to learn this.
Handbreak. I use this to rip the DVDs I made with SONY deck. It outputs all kinds of video codecs but is obviously working with compressed imput files. I don't know if I could get it to accept input directly from one of the cameras or the Canopus.
Audacity. I'm using this to combine audio tracks from various sources to add commentary to silent videos, which i would like to add as a voice over track to my iMovies
Toast. I think this can convert files of one video format to another in the process of copying.
Thanks for any advice on any part of this question.
Steve B

Yes
I found a program but am experiencing lots of trouble with it. I was hoping that others could give me a better suggestion.
I've actually downloaded and installed ffmpeg but the problem I'm experiencing now is that the videos do not convert. The program starts to work and then three seconds later I get the dialog box that says everything has been converted but the file created is 0KB and of course will not open.
Any ideas about what could be going wrong? I've attempted to convert the files to different formats and try converting different files as well. I still have the problem.

Just upgraded to MacBook Pro running 10.8.4. Want to convert old movie files to put in Itunes. Can't upgrade QT player preinstalled, so downloaded QT Player 7 and purchased QTPlayer 7 Pro registration code. Can not get it to upgrade. Called Apple 2x.

Just upgraded to MacBook Pro running 10.8.4. Want to convert old movie files to put in Itunes. Can't upgrade QT player preinstalled, so downloaded QT Player 7 and purchased QTPlayer 7 Pro registration code. Can not get it to upgrade. Called Apple 2x. If you have a fix, you can email me direct at [email protected]

Want to convert old movie files to put in Itunes.
What does "old movies" mean to you? File type, audio and/or video compression format(s)?
Can't upgrade QT player preinstalled, so downloaded QT Player 7 and purchased QTPlayer 7 Pro registration code. Can not get it to upgrade.
Did you follow the instructions found here?
If you have a fix, you can email me direct at [email protected]
To which fix do you refer? Activatng QT 7 Pro or converting the files? Even with QT 7 Pro activated you may need to modify your QT codec component configuration depending on the file type and compression formats used to encode your "old movies." There may be many different problems here with each having one or more "fixes." Please try to be more specific regarding your questions. Converting a muxed VOB MPEG2/AC3 file would be very different different from converting an AVI DivX5/MP3 file depending on which application you are attempting to use.

10.4.11, VMware Fusion and Windows XP (Home Edition) works just fine

OK, so I'm through the installation of VMware Fusion and Windows XP (Home Edition) and I have to say that it was pretty much point and click as advertised. All network services seem to be working and I'm running both OS side-by-side with out a hitch.
Haven't put the system through any rigorous test yet, like VPN, network printing or rending large graphic files, but the installation, setup and normal operation went smoothly taking about an hour in total.
Machine: MacBook Pro, 1.8Ghz with 1G of RAM memory and dual monitors.
Host OS: MacOS 10.4.11

I now have installed XP Pro into a Boot Camp Partition. Basically point and shoot. Then while booted in XP I used PC Mover to migrate my old PC to the Boot Camp partition. With the exception of one program and my virus and firewall programs all went well, almost point and shoot. Then I installed VMWares Fusion and used my Boot Camp partition as the source. If you follow instructions from VMWare things work relatively problem free.
After posting questions on VMwares site about processing video and compiling DVDs in Windows using Fusion I decided that such processor intensive requirements are best handled in the Boot Camp (native) mode.
The biggest problem I have encountered is that Microsoft Office constantly asks to be reactivated when switching between Boot Camp startup and Fusion. No solution I know of, except not to use Office in Boot Camp Mode. Secondly XP Pro required a re-authorization from Microsoft so I could run it in both Boot Camp and Fusion modes. Obtaining the authorization (activation code) from Microsoft was not a problem.

10.2 crashes when I try to convert old libraries for use in the new software. Is there a workaround for this? Or will i have to continue using the previous version to complete older projects?

Final Cut Pro X 10.2 crashes when I try to convert old libraries for use in the new software. Is there a workaround for this? Or will I have to continue using the previous version to complete older projects? the only foreseeable solution is to begin any new projects on 10.2 or importing footage on 10.2 and starting form scratch--which is something i definitely don't want to do or have time to do. ANY advice, thoughts, or opinions would be greatly appreciated! Thank you!
Running 10.10.3 // MacBook Pro (Retina, 15-inch, Early 2013) // 2.4 GHz Intel Core i7 // 8 GB 1600 MHz DDR3

Exactly the same problem with me.
Some other threads advice to remove fonts, clean the caches, remove add ins but nothing works consistenty, for some it looks like it works, for me it failed.
What I did not try yet, was to move the Render files out of the malicious library to trash.

How to convert old Java Servlets to OSGi "Servlet" Bundles

Hello I'm looking for some help/insight on the best way to convert some of our old Java Servlet code into new OSGi Bundles that can be accessed as servlets. I'd like to be able to install the new bundles then access them on one of our CQ instance using something like "/servlet/servlet_name".
So far I've been able to create a new bundle, and install it into CQ but I haven't been able to access the bundle at the servlet mapping URL that I would expect. So far what I've found online has lead me to believe that I need to use the Felix Annotations to describe my servlet.
@Component(immediate = true, metatype = true, label = "Servlet Name")
@Service
@Properties({
    @Property(name = Constants.SERVICE_DESCRIPTION, value = "Servlet Name"),
    @Property(name = "sling.servlet.methods", value={"GET"}),
    @Property(name = "sling.servlet.paths", value = "/servlet/my_servlet_mapping"),
    @Property(name = Constants.SERVICE_VENDOR, value = "VendorName")
public class TellAFriend extends HttpServlet {...
public void doGet(HttpServletRequest req, HttpServletResponse res) throws IOException, ServletException
Once I have this installed, and running without an error in the logs for CQ I tried to go on my local instance to http://localhost:4502/servlet/my_servlet_mapping but I only get 404 Resource Not Found errors. I've even gone to the Sling Resource Resolver and it doesn't resolve to anything either.
Is there more than the Servlet Information need into the Annotations to convert "old" code into a new OSGi Servlet Mapped Bundle?

I must be missing something else configuration wise since I created a new Servlet basically using the code you provided above. I deployed it as part of the bundle that I'm trying to create.
The bundle installs and stars fine but I still can't access the servlet. Are there CRXDE based configurations that are requried too to configure Servlets.
Here's my test servlet file. I tried going to http://localhost:4502/servlet/TestCQServlet and just get the same 404 error I'm getting for the other 2 Servlets Java classes in my Bundle.
import java.io.IOException;
import javax.servlet.ServletException;
import org.apache.felix.scr.annotations.sling.SlingServlet;
import org.apache.sling.api.SlingHttpServletRequest;
import org.apache.sling.api.SlingHttpServletResponse;
import org.apache.sling.api.servlets.SlingSafeMethodsServlet;
@SlingServlet(paths = "/servlet/TestCQServlet", methods = "GET")
public class TestCQServlet extends SlingSafeMethodsServlet {
    // @Reference
    // private Repository repository;
    private static final long serialVersionUID = 6239754936223276983L;
    @Override
    protected void doGet(SlingHttpServletRequest request, SlingHttpServletResponse response) throws ServletException, IOException {
        response.setHeader("Content-Type", "application/json");
        response.getWriter().print("whatever");

I've bought my 1st Mac, since than I've replaced my old disk to a new one - and at the lab they created my new admin's name as admin.. I've changed it after 'root'ing - and now I can't find my photos either at iPhoto/photo booth,what can I do to restore ?

I've bought my 1st Mac, since than I've replaced my old disk to a new one - and at the lab they created my new admin's name as admin.. I've changed it after 'root'ing - and now I can't find my photos either at iPhoto/photo booth, what can I do to restore restore them, they are very importent to me !!!
Please I'll be thankfull.

I stated that I did try to do all of this when I first set up the new computer...I did do the Setup Assistant numerous times but my old computer kept freezing half way through. Even if I did it when I first got the new computer back in Septemeber, I would have had the same issue b/c my old computer has been 'broken' for a while. My old computer can't handle doing too much at once and I think the setup and then migration functions I tried were too much. That's why I was hoping I could use the migration function piecemeal. I wish I could just check off the exact files and folders I want vs. having to choose it at the 'user' level...that's too much for my old computer to have to transfer.

Problem share folder WLC and pc macbookpro

I am doing a migration from my wireless network in the old network in the PC MacBookPro I can see shared files on the network. But when I connect to the SSID configured on the WLC and I can not see shared files on the network. I have no ACL configured on the SSID.

Bonjour is a non-routabe multicast based service. A trick I use sometimes is to configure the WLAN to be in hreap mode if the ap is located locally to the target bonjour device.if your running in local mode, make sure they are on the same vlan and global multicast is enabled.
Sent from Cisco Technical Support iPad App

How do I convert old work done with iMovie HD 6 to view/work with iMovie 11 on my new iMac?

How do I convert old work done with iMovie HD 6 to view and work with in iMovie 11 on my new iMac?

If you still have your iMovie 6 project, you can import it using FILE/IMPORT/iMovieHD Project.
If all you have is the finished movie, you can FILE/IMPORT MOVIE.
If your movie is in DV Stream format, it is advisable to convert it to QuickTime MOV container containing DV codec. Otherwise, the import will be chronological by the date and time the clip was shot, rather than in edited order.

Converting old VHS tapes through camcorder to IMovie???

HELP! Have set up VHS and video with output cable to camcorder (Samsung Mini DV). Then firewire from camcorder to IMac and STILL NO LUCK with converting video! Thought I could convert old VHS tapes into IMovie this way, without having to use a Pinnacle Box, etc.....?
Any suggestions would be GREATLY appreciated. This has been an ongoing family "project" I have taken upon myself and refuse to take tape to a professional when I know my Mac and IMovie can do a BETTER job!

Sue, that was not my point per se. I am not rich enough to own two video cameras. For others in my position a tried and tested analogue to digital converter seems a simpler answer, and a lot less work.

Peculiar error from WLC and LWAP locking out iPhone 6+

WiFi LAN:
WLC Cisco 2504 Software Version 8.0.100.6
LWAP's Cisco 1702i's Software Version IOS 15.3 Mini IOS 8.0.72.236
Single WLAN using WPA2 (AuthPSK)
Apple iPhone 6+ Software Version 8.1.2
The error being reported in the 2504 WLC Message Log is:
"*sntpReceiveTask: Jan 21 10:59:27.457: #LWAPP -3-DUP_IP:spam_Irad.c:39857 The system has added client a8:8e:24:60:a0:52 to exclusion list due to IP Address conflict of AP 192.168.10.10, this is a duplicate of IP on another machine (MAC a8:8e:24:60:a0:52)"
In the error above:
a8:8e:24:60:a0:52 - Is the Smart Phone being locked out of the LAN.
192.168.10.10 - Is the IP address of the LWAP where the problem started yesterday.
To troubleshoot, I took the smartphone to another LWAP 100 meters away and the above error still gets reported to the 2504 WLC.
My questions to the support community:
1) I have looked everywhere for this "Exclusion List" on the 2504 WLC GUI and cannot fine it. Does it exist on the 2504 GUI? CLI?
2) If not, is it on the LWAP?
My thinking is to clear this list to see if this smartphone can then join the LAN. THX

Thanks for that Scott. I will do the updates when a window opens up. I performed the opened SSID as you suggested and the smartphone would not join on the first attempt. On the second attempt I manually entered network settings and it finally joined and has held for over an hour now. I have 2 iPhone 6 smartphones with this problem now and 45 mixed iPhone 6's/Droids running flawlessly with WPA2/AES Security. I will attach a couple screenshots of the security setup to this post.
On another note, I had originally though that this was an Apple IOS 8 issue as I found a recent thread on the Apple Support Communities mentioning the same issue of continuous re-logging in.
https://discussions.apple.com/thread/6536955

Old router broke - got new one and having trouble getting wireless to work

Hi -I've had a 1st gen ATV for about a year. I've had difficulties when my router gets disconnected or something for a while. I had it replaced today. Now I'm having a problem getting the aTV to hook up wifi.
Everything runs perfectly streaming from my computer (PC) when hooked up with ethernet. But when I disconnect - the screen does not show the router address or the dns address and the connection is lost. I know its an easy fix but I can't for the life of me figure out what to do. I'm ok with a computer but not totally tech savvy.
I've tried shutting down my router firewall and my computer firewall. I tried as suggested on the site to add the MAC info. When i run the wireless set up - it sees my new router (2wire) and goes thru that, then it says it connected or something but that I am not connected to the internet. It gives me the option to do that and it appears to work but then no router or DNS info and therefore it won't work.
Can you help?

is there any manual setting of the IP address setup on the Apple TV? If it is stuck with an old Manual setup on it, it could be not getting the new assignment from your Router.... is the router setup with DHCP enabled? Have you verified that you can connect to the internet from any other device such as an iPad, iPhone, Macbook, Notebook or wifi anything other than the apple tv?

Convert old Logic 5.x PST Files on PC to FXP/FXB

I'd like to know if and how I can convert old PST files in Logic 5.x on a PC to FXP/FXB (VST format) or simply make them usable in Logic Pro/Logic Studio where I've the same plugins in AudioUnit format. I'd even be willing to code my own utility if I had access to the PST file format from an older version of Logic. I really appreciate everyone's time!

If I remember correctly, Logic OSX would load PST settings files correctly (and then be able to resave as .aupresets) but only for Logic's own plugs, not for third-party ones.
You'll either have to work out your own solutions, or go back to the older versions and resave those settings in the plugins own native handling, if it has it's own patch formats....

Converting old dvd for imovie

Six years ago I converted old home movies with a VHS/DVD converter. I would now like to get them into imovie for editing but it couldn't import/read them. So, I downloaded Handbrake and converted the DVDs to .m4v and Imovie wouldn't import that either. I saw on some previous discussion that suggested changing the file extension to MOV, I did that and imovie will still not recognize them.
When I try to just open it normal with quicktime/itunes I get the message that it is not in a format recognized.
Are there some setting in Handbrake that I am missing when I originally convert?
Thank you!

You didn't say what format you converted them to, but if you don't feel like spending $55:
You need to convert the files to DV which iMovie is designed to handle. For that you need mpegStreamclip:
http://www.squared5.com/svideo/mpeg-streamclip-mac.html
which is free, but you must also have the Apple mpeg2 plugin :
http://www.apple.com/quicktime/mpeg2/
(unless you are running Lion in which case see below))
which is a mere $20.
Another possibility is to use DVDxDV:
http://www.dvdxdv.com/NewFolderLookSite/Products/DVDxDV.overview.htm
which costs $25.
For the benefit of others who may read this thread:
Obviously the foregoing only applies to DVDs you have made yourself, or other home-made DVDs that have been given to you. It will NOT work on copy-protected commercial DVDs, which in any case would be illegal.
If you are running Lion:
From the MPEG Streamclip homepage
The installer of the MPEG-2 Playback Component may refuse to install the component in Lion. Apple states the component is unnecessary in Lion, however MPEG Streamclip still needs it.
To install the component in Lion, please download MPEG Streamclip 1.9.3b7 beta above; inside the disk image you will find the Utility MPEG2 Component Lion: use it to install the MPEG-2 Playback Component in Lion. The original installer's disk image (QuickTimeMPEG2.dmg) is required.
The current versions of MPEG Streamclip cannot take advantage of the built-in MPEG-2 functionality of Lion. For MPEG-2 files you still need to install the QuickTime MPEG-2 Playback Component, which is not preinstalled in Lion. You don't have to install QuickTime 7.

Converting old 1240AG setup to VMware WLC and setup question

Similar Messages

Maybe you are looking for