Cooling fans constantly run @ full speed after replacing the upper CPU??

After replacing the upper CPU on a Power Mac G5 (June 2004), Dual 1.8Ghz PowerPC, model M9454LL/A, all the cooling fans constantly run at full speed. All other operations are normal.
I've read, "...after replacing or switching CPU locations the Logic Board doesn't properly recognize the CPU's in their new location and a "Thermal Calibration" is needed". Could a "Thermal Calibration" possibly correct the constant full fan speed issue?
What software would be required?

Hi-
Could a "Thermal Calibration" possibly correct the constant full fan speed issue?
Yes.
What software would be required?
The Apple Service Diagnostic disc (ASD) of the proper version for your machine.
Call an authorized Apple service provider and arrange a calibration, as the disc is not readily available to individuals.

Similar Messages

  • Fans running full speed after hard drive replacement

    I have a 24" aluminum iMac (iMac7,1) which had a hard drive failure. I replaced the hard drive myself and all went well. However, now my fans are running full speed. This appears to be because of a problem with detecting my temperature sensors now. During the install I only touched two temp. sensors, the hard drive sensor and the LCD sensor. I made special care to make sure I got the sensors back in place.
    Using iStat Pro the only temp. sensors I have readings for are the Hard Drive and Power Supply. I am missing ambient, optical drive, CPU, and display. Out of those the only one out of the missing ones I touched are the display one. I have since gone back into the machine to ensure the LCD temp. sensor was fully connected and to ensure the HD one was connected (although that one is working).
    What is really strange is the ambient sensor appears to be a diode on the main board so I really don't see a way I could have messed that one up. Also, I didn't touch the CPU sensor (didn't even see it), nor did I touch the optical sensor.
    Anyway I have tried:
    PRAM reset
    SMC reset
    went back into the box to make sure all temp sensors where in place.
    I am out of troubleshooting ideas. Can anyone provide additional insight?

    Mechanic man thanks for the response.
    Besides for the fan noise the machine is running like a champ. The new hard drive seems to be fine, actually my machine boots up faster now than it ever did (faster drive I suppose). I ran disk utility and did a verify on the new disk and it didn't detect any problems.
    The fans run at full speed immediately at power-on (maybe a one second pause). I first noticed it when I booted up from the startup disk to do a time machine restore. So yes, it occurs when booting from a system disk.
    I have been unable to run Apple Hardware Test, I saw this step in some google searching and Apple docs but I don't seem to have AHT on any disk. I have tried putting the Snow Leopard disk in and holding "d" at boot time to no affect. I did some further reading and found that AHT may only be included on disks that come with the machine. I am going to try to dig up my Tiger disks and see if I can get AHT to run from there (10.4 was the factory installed OS when I bought my iMac).
    I am also considering trying to re-install SMC firmware (http://support.apple.com/kb/HT2368). Even though it will be the same version at least I know the SMC reset has taken place.
    Since the fans run full speed right at start up that suggests to me that it is a physical hardware problem (i.e. something wrong with the sensors) or a firmware issue. I am leaning toward firmware.

  • CPU fan running full speed after 15 minutes

    My 3 month old iMac 24" has just started having fan problems.
    Before I went away on a training course, it was working fine. Left it switched off at the outlet for 3 days, now the CPU fan runs full speed after the iMac has been switched on for 15 to 20 minutes.
    CPU temp is 24C, CPU heatsink is 28C. Ambient is 17C. CPU fan is 3600rpm. Other fans are normal.
    CPU usage is less that 10%. Only Safari is running.
    I've tried resetting the SMC - left all plugs disconnected for 15 minutes, reconnected mains power for 15 minutes, reconnected USB, then switched on.
    Still the same - OK for 15 minutes, then CPU fan runs full speed.
    Anything else that I can try?

    I tried again, following your instructions exactly. It seemed to work, running normally for about an hour.
    I left all the USB devices unplugged, except for the keyboard and mouse.
    I then shut the iMac down, but left the mains power turned on at the wall. When I switched it on again 2 hours later, all was OK for 15 minutes, then the CPU fan ran at full speed.
    Shutting down for a few seconds fixes it for another 15 minutes.
    I'm wondering if it's a software problem, although I haven't loaded any apps recently, apart from a few monitoring programs since this problem appeared.
    Last night I left it running the extended hardware test for a couple of hours, and the fans were fine.
    One thing that I noticed yesterday was that the "GPU" temperature readings in iStat were all missing (just "-" displayed) for a couple of seconds when I clicked on Dashboard. Is there a way to keep iStat open while I'm using the iMac?
    I think I'll try booting XP and see what happens.

  • Mac Pro fans run full speed after installing Solid State Drives

    I recently visited the Genius Bar at my local Apple store because my Mac Pro's fans were running at full speed after installing 2 solid state drives. The genius told me that it was because the drives themselves are so small they don't touch the metal tab on the motherboard that reads the drive's temperature, so it defaults to running full speed. Does anyone know how to fix this problem? I've tried smcFan Control but it doesn't let me set the actual fan speed. I'm getting 5200 rpms on my Boost A and B fans, and this causes an insane amount of noise. Can anyone help?

    Which model Mac Pro?
    I have an SSD in a 2009  (MacPro4,1). I removed it from the 2.5 in stamped metal can, and just installed the bare circuit board onto the SATA connector. It does not make any contact with the metal tab below the SATA connector. The only trouble I have is that Tech Tool Pro says its temperature is not optimum when it does disk tests.

  • Fans intermittently run @ full speed - problem solved - wireless card was culprit

    I hope this helps someone in the future with this odd problem, that I see is rare but not unknown.
    I have a P7-1222 which from new, would on about 1 in 10 powerups (i.e., random) have both CPU and case fans running full speed (several thousand RPM) making the machine very loud.  They would reset to more normal speeds of ~ 1000 on a cold or hot reset.
    TMPIN1 at time this occurred at powerup would, via HWMONITOR or SIW, show 99C (which was impossible), making the fans race.
    Two motherboard replacements, PS substitution, CPU swap etc. did nothing.   The intermittent problem persisted.
    Now the culprit has been identified.  I replaced the wireless LAN/Bluetooth combo PCI mini card with an identical unit from eBay (in this machine, an HP COMPAQ 615939-001 652279-001 WIRELESS N BLUETOOTH COMBO WLAN MINICARD).  The problem of intermittent fan racing is now gone.
    The wireless card in the machine seems to have been the culprit, perhaps occasionally sending a noise spike on powerup as it initialized onto the bus, thus affecting the Fintek F71858 LPCIO  TMPIN1 reading  and making it 99C, causing fans to race via BIOS thinking the machine was burning up!
    Doing some investigating, I had found the following in the Data Sheet for the Fintek F71858 LPCIO chip ("Hardware KBC with ACPI, Temp. and Fan Control") used on numerous HP/Pegatron motherboards, including the Carmel/Carmel2 and other HP boards that use the same basic circuit layout:
    =======================
    8. PCB Layout Guide
    F71858 adopts Current Mode measure method to do temperature detected. The measure data will not be affected by different process of CPU due to use current mode technology. This technology measures mini-voltage from the remote sensor so a good PCB layout must be cared about noise minimizing. The noises often come from circuit trace which is a track from remote sensor (CPU side) to detect circuit input (F71858 side). The signal on this track will be inducted mini-noises when it passes through a high electromagnetic area. Those effects will result in the mini-noises and show in the detected side. It will be reported a wrong data which you want to measure. Please pay attention and follow up the check list below in order to get an actual and real temperature inside the chip.
    ... Place the F71858 as close as practical to the remote sensor diode. In noisy environments, such as a computer main-board, the distance can be 4 to 8 inches. (typ). This length can be increased if the worst noise sources are avoided.
    Noise sources generally include clock generators, CRTs, memory buses and PCI/ISA bus etc
    =======================
    And defective wireless cards can be a noise source too, it seems.

    The issue was what I expected.  I picked a new reader last night and everything works fine.   My old card reader just didn't work with the new card.

  • 865PE Neo2 north branch fan always running full speed

    Core Center does not seem to work.  I have the latest version and it is quiet for first 5 minutes, then it gets louder and louder.  I have replaced the NB fan once and that seemed to help for a while, but now it is always running at full speed.  The fan goes to full speed even when no one is using the computer for 1/2 hour.
    1)  How to troubleshoot?
    2)  Are there other fan speed control programs that actually let you control the speed of the fans?

    Try SpeedFan.  If your mobo's sensor chip is supported by Speedfan, you can adjust the fanspeed with it.
    Another option would be to replace the NB fansink with a Zalman fanless northbridge heatsink like the NB47J...  I got a 865PE Neo2-V board and it came with a passive heatsink, so a passive heatsink might work OK for yours as long as you got good case airflow.
    Good luck.

  • Fans Run Full Speed After Upgrades

    I have a late 2007 15" Macbook Pro. I just recently replaced the hard drive (because i needed more space) and the keyboard (because it was defective) and since i've put it back together the fans are always running at full speed. I do have an smc control app but the adjustments i make are not affecting the fan speed at all. Does anyone know what I might have done wrong to cause this? and is it something I can fix?

    I've checked all the connections and I don't appear to see anything loose, or any crimped or cut wires. Someone though it might be that the new hard drive I put in runs at a higher rpm (7200) than the original 5400rpm drive, but that was ruled out after placing the original drive back in. At this point it looks like I may be replacing this laptop if I can't get this issue resolved.

  • Satellite Pro P100 GPU Fan off or full speed after Bios-update to 4.20

    Hello,
    after installing the brandnew Bios-update 4.20 the GPU fan is when the notebook is cool off. While working with it the GPU temperature rises up to 100C (very very hot), then the fan begins to run on medium speed and the GPU cools down. After a restart, eg. next day, the fan always runs on medium or high speed (very noisy!!). With the the bios version before this problem didn't appear.
    Has someone the same problem with his notebook?
    Did anyone have the Bios-update before 4.20 and can send it to me???
    Greets
    Rommulaner

    Hi all,
    I've got a similar problem. After updating the BIOS of my SP P100 (PSPAHE) to 4.2 on of the fans runs constantly. I was very astonished about the WinPhlash Software anyway: I just wanted to see what it looks like, and it started updating BIOS virus-like automatically without any message or confirmation etc.
    With the first reboot I got a bluescreen immediately after Vista started booting. With the following reboot, the system started properly - everything seemed to be ok. Since then the system obviously can't control the fan anymore.
    The bluescreen-error is reproduceable - it occurs after each trial. I already tried to update BIOS with a freshly installed Vista (Recovery DVD) bfore installing a single problem - same result.
    I only see 2 possibilities to perhaps solve the problem: hopefully a re-downgrade to 4.0 can successfully be done. Second possibility would perhaps be to remove Vista and install XP instead hoping that the BIOS update doesn't hang up then.
    Unfortunately, the previous BIOS version is not on the support pages. . If anyone gets hold of it pls. post here.

  • Firefox 4 constantly runs slow,even after following the solutions

    I have tried the solution pages and help,but firefox 4 optimised for yahoo still continues to run slow. I have never had this problem with firefox 3.6 for yahoo. this is driving me crazy,please help!!

    try google chrome 10.x, these kinds of problem often happens to some specific websites. so, you need an alternative sometimes. and sometimes it is the problem of the websites, so calm down buddy. during internet rush hours i.e 18:00-22:00 monday to friday, it may make you unpleasant even with some BIG websites, so don't be that fuss to this.

  • Mac mini server and harddrive 1 of 2 failed now fan runs full speed

    I have a 2010 mac mini server. One of the drives failed.
    I took out the bad one and the fan started to run full speed.
    Replaced that drive with a new one. runs great but fan is running.
    I put the temp sensor in exact same place but had to use a small pc of tape
    to hold it on. I used the same tape that was holding the wires to the drive.
    I used the temp sensor connector on the logic board closest to the fan connector?
    Does that matter?

    Hello, possible work arounds...
    HDD Fan Control
    HDD Fan Control works to fix this issue by reading the drives internal temperature using the S.M.A.R.T protocol and set the fans actual speed to a value good to protect the drive. 
It runs at startup and continually to always control the fan correctly, prevent the loud fan noise and protect the drive from overheating.
    Free SSDFan Control...
    http://exirion.net/ssdfanctrl/

  • TS1433 Fans run at full speed after computer turns on

    Fans run at full speed after computer turns on, and a lot of times while i'm working they suddenly start blowing and won't stop. Tried the reset SMC, nothing happens. Also the unplug powercord-method does nothing.
    Anyone?

    Exactly what method did you use to reset the SMC, every Mac has different methods and I want to ensure you used the method for an Intel based Imac. The correct instructions are in the iMac SMC and PRAM reset link. Do the SMC reset at least 2X!

  • Fan running at full speed after shut down.

    My brand new, three day old 8 core Mac Pro has already frozen three times. I have been reading about the screen garbage and then the freeze. That is happening with me, too. But what is going on right now as I type on my old G4 is that the fan on the new Mac Pro is running full speed and the computer has been shut down! The fan has been blowing like this for at least 30 minutes. I am hesitant to unplug. But I can't just leave the office with it blowing like that. What is going on?

    Have a lot of USB stuff attached...
    Apple keyboard/mouse, Kensington track ball, (then through hub) Logitech web-cam, External HD (USB) for time-machine, epson scanner, iPod USB cable, shuffle, dock, and...ah ha..may be a culprit...a Microsoft joystick for playing x-plane (when I was thinking about what I do when this happens, I said I'd switched resolutions to use xplane..but, of course, I would have had the joystick plugged in as well..this could be the one difference (I only connect the joystick when I'm going to use x-plane)).
    I will experiment some tonight...shutting down with and without the joystick to see if that makes any difference.
    Now that I think of it, that seems to be the one 'difference factor'...and it would be Karma to have the Microsoft hardware messing up my Mac.
    I don't have any extra PCI...nothing in firewire.
    Thanks for giving me a possible lead...I'll report back.
    Message was edited by: midiotlv
    Message was edited by: midiotlv

  • After Restart fans operate at full speed with no picture

    Yesterday I used my mac all day, no problems. Last night I decided to do a restart in order to freshen the memory. I had quit all applications.
    THis morning I powered it up and the imac came on but the white light in the lower right corner of the mac lit up and stayed on. The fans sound like they are running full speed. No pic on the mac but it obviously has power and powers up.
    Any ideas on what happened and how to fix this outside of taking it in for service? Thank you.

    So I made my ProCare appointment online for this afternoon. I showed up on time and there was a Apple tech AT THE FRONT OF THE STORE that greeted me, took my iMac and asked me to follow him to the back of the store to get written up for service. After 10 minutes they took the mac to service and determined that the problem is:
    MLB Failure
    Issue: Boots to no video; fan spins up
    Proposed Solution: Replace MLB (a logic board)
    So they need to replace item number 661-3597 Logic Board and it is considered Hardware Repair Level 2.
    I just received a call at 8:55 p.m. tonight from an Apple store representative saying my imac is done, install went good and I can pick it up anytime tomorrow.
    Wow! What awesome service. ProCare is every bit worth it. Thank you to all the helpful people at the Apple Store at Woodfield Mall in Schaumburg, IL. This is the second time I have taken it in for service (unfortunately) and both times they have went above and beyond to service my machine (because I'm an ProCare member).
    Oh. Yeah...and they serviced it at no charge.

  • Cold MBP, exhaust fan running full speed

    Hello,
    My 3mo old MBP exhaust fan has started running full speed (6200rpm), no processes or heat are to blame.
    iStat pro say's the fan is currently at 6196rpm, highest temp sensor is at 30 degrees C.
    Process monitoring says kernel_task using 160% of my two cores (interrupts?), this is a cause or a effect.
    Reseting SMC had no improvement (unsure if I've managed to do correctly). Appart from that the machine works, very slowly, noisy, and very cold on my laps.
    I'm on a business trip, don't have the diagnostic CD with me...
    Any ideas so I can at least work during this trip ?
    Thanks for your help, and for these forums.

    Hello folks,
    I'm in the same situation, the only difference is my hardware from 2006:
    Model Name: MacBook Pro
    Model Identifier: MacBookPro1,2
    Processor Name: Intel Core Duo
    Processor Speed: 2,16 GHz
    After running the ASD, I got this:
    +Temp Sensor - Palm rest L test 1 - Sensor Reads Within Operating Range.+
    +-Check to ensure that sensor reads within operating range.+
    +ERROR - Unable to read sensor+
    +- T E S T F A I L E D -+
    The sensor code is the same one from the post above: Ts0P.
    So now, after looking for more than 4 hours on the internet, I couldn't find a clue.
    What exactly is the location of this sensor?
    Can someone please post a picture?
    How can i fix this?
    Thanks for everybody.
    Message was edited by: Pierobon
    Message was edited by: Pierobon

  • G5 Fans run full speed.

    My G5 Duel 2 ghz June 2004 died. If it started up it could freeze at any time and then the fans would run wild. After much research the outcome was a bad processor or logic board. Because of an error message I got only once in this whole ordeal that mentioned cpu 1 I decided to go the processor route. I thought cpu 1 might be the top one. I got one off of ebay paying close attention to get it from the same machine and the same part number, 630-6611. It works great. I'm now off my Cube and back to my G5. Only problem now is the fans run at almost full speed all the time, Very loud! I think I've heard about a command I can type into the terminal to fix this. Is this true? I know the fans run at full speed when they don't get info from the temp sensors. Can this be fixed?

    I noticed recently that a lot of powermac G5's are having the same startup issues. The grey screen with or without the Apple logo and just stops there. I have a dual 2.7 I bought in 2005 and never a freeze up, never an issue. I use matched Crucial ram and often do permission repair before and after any updates. I run DU often and never a problem until last week.I started it up as usual every morning and then the blank grey screen. I Changed internal battery for new, zapped the pram, PMU reset, disconnected every wire going into it except the keyboard and mouse, made sure I had at least 20% free HD space, dusted it inside and even checked the ram with another G5 to verify. I did single user mode and also tried applejack but both frooze up the keyboard. I was pulling my hair out.I did target disk mode and every thing in the drive checks out with Disk Warrior and DU. It eventually started up one morning without any issues and ran fine all day and the temp sensors were at a steady 62%C each at automatic processor performance in energy saver.The next morning it was back to the same frozen grey screen, it did not do the spinning gear thing. I must have worn my fingers out holding 4 keys for the pram boing 2 times thing. So it wasn't the mobo or the processor going bad or else how did it manage to run all day before? And I mean a solid 14 hour run. Now I did something just after the pram zap and let go just the P &R keys while still holding down the Command and option keys after the 2nd boing holded down the shift and delete key along with the Command and option for a short while. It started up. I repeated this a few times and it worked for me. Now I understand that holding down the Command -option-shift -delete keys forces a startup from a drive other than the main one.That was essentially what I did after the pram thing and it worked. at least for now. Go figure. At least I know it's not the processors or mobo the culprit.

Maybe you are looking for