Copa data source (urgent urgent)

HI friends
M newly jioned in BI. in reports some fields are showing blanks. i cheked in BI side every thing ok. i cheked the in the source system in RSA3 data for that data source(copa data source) ter also same fields are missing.this is COPA extraction. i think main problem is DATA SOURCE is it corrcte ?. i need to check some wer else.plz m in confuse plz advise me.
Regards
siva

Hi
Usually, if the data is missing in COPA, then the next source will be veryfying SD data.
Say some of the condition types were created in SD module but those were not updated/mapped/configured in COPA, so obviously those values/fields will be missing in COPA and BI.
Hope this helps.
regards
S

Similar Messages

PLIKZ field for COPA data source not there in Extract structure.

Hello all,
When I create a data source for COPA the PLIKZ field from the segment level is not maintained in the Extract structure and it is not replicated to BW also. But the other field GJHAR is maintained in the Extract structure which is also there in the segment level!!
Clarify me why it is not available in extract structure? Also we are in 4.7 version and 3, 5 in BW.
Points will be assigned!!!
Thanks
Ram

Hello Friends,
Could some one help me why the field PLIKZ is not available in the Extract structure when i create a COPA Data source?
Need ur suggestions urgently!!!
Helps please
Thanks in advance once again

COPA data source does not allow delta - once more

Hello,
When I try to generate COPA data source (tran KEB0) the system already have "Generic delta" in delta method field.
I want to use timestamp instead of that. How I can switch to timestamp?
A

All COPA datasources are timestamp based (which is a generic delta method).
I do not think you have an option to change it (not that there is any need since it already is what you want ie timestamp based), the system automatically creates a timestamp based delta method (each delta extracting records upto 30 min back from the current extraction time). Do not worry about the 'generic delta method' appearing in your KEB0.

COPA data source does not allow delta

Hello,
I wanna generate new COPA data source. I did it but it doies not allow to establish delta.
Where I go to Simulate initialization of delta method and try to determinate time stamp the system tells me that "Function is not possible because data source is defined for generic delta"
How can I establish delta???

Aleksandrs, normally you only have to run a init load from BW. Then only delta packages.
regards
Siggi

COPA data source RSA3, RD155

Hi,
when we run the RSA3 for COPA data source 1_CO_PA2901000_ACC we get error RD155 " No Source could be found to answer the search query".
Any ideas
Umang

Hi,
check out this link
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes/sdn_oss_bw_bct/~form/handler
hope this helps
assign poins if helpful
Janardhan Kumar

COPA data source delivers incorrect values

Hello
We have one PL report in R3. I generated COPA data source and use it to extract data in BW. However, there is a difference between report in R3 and report in BW. Is it possible that COPA-generated data source does not bring correct values? How to check it and correct?
I am 100% sure that report on R3 and BW uses the same logic.

Hi Aleksanders,
Check some of the values using RSA3 tcode and check the difference between these values and the R/3 Report values...If there is a difference then datasource is not created properly...if it is matching then on bw side..load the data as of time and compare it to R/3 data.....definitly it helps you....
regs,
mahantesh

COPA data source - add a field

Hi Experts,
I got answer to the question that I asked for adding ship-to party to COPA data source and in operating concern.
Now, when I go to KEB0 and display datasource, it doesnt show my added field ship-to party as checked.
so, help me understanding
1) how can I apply the change in operating concern to datasource? or make field visible in extract structure
2) if i delete the datasource and re-create it, will my CE1XXXX, CE2XXXX, CE3XXXX, CE4XXXX are cleared or not?
3) I have active delta running on COPA datasource, what are the steps to ensure contnuity of this delta?
4) if i need to fill newly added field in the CE1XXXX, CE2XXXX, CE3XXXX, CE4XXXX tables (historical value for ship-to), how can I achieve this?
5) what steps I need to take care while transporting these changes to prod?
Thanks,
Purvang

HI,
Following steps will help you...
1) use "KEQ3" to activate "KUNWE" characteristics for Ship-to Party
2) Add the field in your data structure in tcode "KEA0".
3) Activate and generate the "Operating concern"
Please revert back if you still need help.
Regards

COPA data source data type changed for BUKRS

Hi Exp,
I've created one copa data source with cost based successfully in R/3 system. I've replicated that into BI system bu the problem is for characteristic BUKRS [Company code] the data type showing REF in BI which is non existance and hence i'm unable to activate this data source.
Coudl anyone plese help...........
Thanks & Regards,
Amarnath

Hi Ramesh,
Thanks for your reply. It is in internal format only. I changed it to external and selected ALPHA conversion also but it's of no use. I don't know why. Is it the error on BI side or R/3 side?
Thanks & Regards,
Amarnath

COPA Data Source: possible to enhance using exit?

Hi BI experts,
I got a question about if it is possible to enhance COPA data source by using user exit (just like the way to enahance other data sources in the business content).
The background:
I have to include several new fields in COPA data source. Since COPA data source is generated (not a data source from business content like LIS data sources).
My questions:
1) Is it the recommended way to enhance the existing COPA data source using exit?
2) or it would be better to delete the existing one and create a new one with the two additional fields?
3) any potential issue to be expected?
Your feedback and help is highly appreciated.
Regards,
Sally

Hi
1) Is it the recommended way to enhance the existing COPA data source using exit?
Yes, we can enhance COPA DS via User Exit, Provided the fields should be from other different tables which are not from Segment Tables.
2) or it would be better to delete the existing one and create a new one with the two additional fields?
If the fields are from Segment Tables, it is always better to delete the existing one and Recreate the same
3) any potential issue to be expected?
Appending/Enhancing fields are always bit difficult and my lead into errors in future, based on the critical functionality we use.. But I recommend DELETE THE DS AND RECREATE WITH COPA always.Hope it helps

How to enhance copa data source.

Hi,
I have to enhance copa data source 1_co_pa300beka_o01. Actually I have to add one field vstel from VBAP table to this data source.
Can you tell me full procedure about enhancing data source ?
It can not be done directly. I think i have to delete and re-create data source in R3 system.
For this i have to do all thing in KEB0 .
Am i right?
So please tell me full procedure to enhancing copa data source also tell me if i enhance copa data source , which type of problem can be come at BW side.
Thanks
Devesh Babu

I'm not sure if we can enhance CO-PA datasources. Even if you can enhance, whenever there are changes to the Operating concern in R/3 you would have to delete and re-create the datasource. While doing this you would have to re-do the appends again. DS 2lis_11_VAITM extracts data from VBAP. Check if the datasource already brings this field. Otherwise enhance it. In the CO-PA dataflow lookup the DSO which has VBAP data from the datasource and get the necessary field.
Other option is to ask functional folks to add the field to the CO-PA operating concern.

About creating data source(urgent)

Hi,
I am abap developer. i don't know much about crm.
our requirement is :
i need to create one infoset in sap r/3.
we want to use that infoset in crm server to create data source.
we use transaction code : CRMD_MKTDS
We specify these values.
Origin Type
RFC Destination
InfoSet
Description
businee pastner
But we are not getting any infoset from r/3 server.
we are getting only crm infoset.
I check RFC Destination. Its working fine.
It gives me error : InfoSet ztest either does not exist or has not yet been generated
Thanks,
Jack

Hi,
You can get the data using a db link and the proc is as follows..
CREATE DATABASE LINK OTHERDATABASE ...;
CREATE TABLE XXXX
AS
SELECT * FROM TBL@OTHERDATABASE ;
Good Luck,
Siva

0FIGL_O02 DATA SOURCE URGENT PLZ

Hi Gurus,
Can you please let me know the related <b>data sources for the given 0FIGL_O02 ODS object.</b>
Thanks & Regards
vadlamudi

Hi,
You can find this info in SAP help...please try to search:
http://help.sap.com/saphelp_nw70/helpdata/en/6e/ff703b3de59e4fe10000000a114084/content.htm
http://help.sap.com/saphelp_nw70/helpdata/en/f2/f7e93a4295ac61e10000000a114084/content.htm
Hope this helps...

Transport Enhanced Data source - Urgent - Please help

Hi,
I have enhanced a standard data source by adding few columns and implementing BADI, how can i transport this enhanced data source/ extractor to another server. currently when i see in SE10 i could see only the append structure name, when i released the transport the enhanced extract structure is not there instead the standard structure only i there, could you please tell how can i transport.
Thanks
Akila.R

Hi,
First try to see the enhanced fields are available or not in original system by double clicking on the above datasource, if fields are available try to uncheck Filed option.
Once enhacement is done for the particular business content extractor, the enhanced fileds should show at the end of the extract structure using Append option.
if it is not showing means, fileds are not enhanced for that extract structure..
for that go to SE11-> give your exctract structure->in top most click on Append structure-> then give you enhanced structure name->activate..
Regards
SK

*** Transporting Generated Export Data Source *** urgent issue

Hi All,
I have generated export data source from info object Company Code,
And trying to transport the Export data source, i.e. 8Company_code to QA system.
Its showing the log that, imported sucessfully, but, i can't see the object in QA.
Iam currently working on BW 3.5 system.
Please help.
Thanks,
Nisha

Hi Luis,
Thanks for this.
Yes, i went into Transport connector >> choosen the object >> Data flow before >>
Ticked the Data sources >> changed the Package from $TMP to ZXXX >> Generated Transport request >> Released it >> Transported it.
But, still can't see....
Cheers,
Nisha

Copa data source

Hi experts,
I created one data source for copa
in rsa2 No errors
when I go to rsa3 it,s showing error msgs
It,s termanating when i check the log(in rsa3)
Msg is probelm calss is very important 1
incorrect field name for selection
How can i sol this error ?

Hi Shilpa,
Where exactly did you generate the DataSource?
You can do it in a couple of ways.
1. Through SBIW in R/3, through the meny tree.
2. Run Report RKEBW100 in SE38.
3. 1_CO_PA_<any name>
4. Select Create Radio Button.
5. Give the Operating Concern name
6. Select the Fields in the next screen.
7. Click on Info Catalogue and you are done.
In RSA3 check if there are any mandatory fields to which you have to pass values and then execute.
Regards,
Tom.

Copa data source (urgent urgent)

Similar Messages

Maybe you are looking for