Copying cameras and lights

Is there a way to copy cameras and lights (along with properties, keyframes, etc.) from one project to another?
Thanks!

Couple ways:
1) drag your cameras and lights to your favorites folder or to the file browser, then drag them into the new project
2) with both projects open and positioned so you can see both layers tabs, drag the cameras and lights directly to the layers tab of the new project

Similar Messages

My camera and light/flash will not work!

The camera- when I try to use the camera it just shows black. There is nothing covering either camera face. I have already tried resetting the iPod to see if that would make it work but it didn't.
The light/flash- it just doesn't work won't even turn on.
If there is an easy way to fix this please let me know.
Thank you!

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Is there a way to switch off by default the video on FaceTime? I only ever use this app for audio/calls and hate the video being on. I especially hate that if I leave the app open to receive calls it means the camera and green light are on.

My issue is that I can't find a way to have the camera switched off when the app is open and so this means if I want the app open all day to receive calls then the camera is going to be on the whole time. Even if it didn't potentially drain the battery, or add to the CPU usage or whatever else may cause any problems whatsoever (wheel of death!), I just don't want the camera on as I don't see myself ever wanting to use the video call feature but I would use the audio/call multiple times throughout the day to make and receive calls. The camera being on when the app is open is enough to prevent me from using the app. Also ever since seeing that episode of criminal minds where if you saw the green light on above the screen then it meant the killer was watching you!
Basically I just can't believe there isn't a way to disable the camera whilst having the app running. I know when initiating an audio call the camera goes away, but I would like the camera away the whole time. To me it just would make sense that if you click the video option then the camera is on, and if you click the audio option then the camera goes off. It just seems waaaaay to basic a thought for apple to have missed... Let's face it, we're not all as pretty as the people in the apple adverts and don't want to see our ugly mugs staring back as us when we work all day at our macs!

I have exactly the same concern. It seems it would be a simple fix for Apple to allow users to turn off the camera (and even the mic) while keeping FaceTime open -- especially now that it turns out FaceTime must remain open in order to send and receive iPhone calls on a Mac.
I like to think this new functionality of FaceTime will be baked into a future release of Yosemite, as the current setup has that not-quite-finished feel of a work in progress. In the meantime, there's nothing like a little piece of Post-It stuck over the camera to keep the NSA from watching your face as you type a post to the Apple Support Communities.

Camera and led light not working after IOS 7 update on iphone 5 help please!!

After I installed the update my led light won't work for the flashlight and my camera doesn't work either. Only the front facing camera works. Any suggestions?

thanks for the suggestions, i tried the ideas you suggested but i dont even get a camera showing for the rear camera, i also noticed the torchlight no longer works. i did all the steps but no luck.
So I took my camera to the genius bar this weekend as well as walking through various steps with the apple guys in ohio support over the net.
With the guys at the genius bar, after i insisted that it must be software as the rear camera stopped working only after the softwre update, they continued to assure me it was hardware and talked me into letting them replace the camera, they then took it to the back and tried fixing a camera and 30 minutes later came out and said the rear camera is no longer being detected and wanted me to replace the motherboard for yet more money. im glad they didnt charge me for the new camera though as it still didnt work.
anyway the motherboard idea i rejected as it was just 2 months out of warranty and had only stopped working the day after the release of 7.0.2, so im going to wait until the next few releases to see what happens, as i dont believe for a second its hardware. i expected a stock answer from apple and its exactly what i got even after my explanation of how it was working the day before the release. not overly impressed with the whole process.
i wanted to back down to 7.0.1 to confirm the camera still works but they said no chance so i cant even see if it still works ouside 7.0.2. anyway will update if i get any further progress.

After instaling the ios 8.2 my camera and flash light stoped to work. I have a iphone 5c.

iPhone 5c
ios 8.2
camera and flash light stoped to work

Close all open apps by double-tapping the home button, then swiping up and off the screen with the app window (not the smaller icon).
Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. (No data loss)

Hey plz help me out!! i am using macbook pro 10.5.8..... and was using photobooth...and then after some time i opened it and there was no green light on cam, and it displayed nothing! plz tell me how to fix it! i want to see my face again!!! plz help me

hey plz help me out!! i am using macbook pro 10.5.8..... and was using photobooth...and then after some time i opened it and there was no green light on cam, and it displayed nothing! plz tell me how to fix it! i want to see my face again!!! plz help me

iSight troubleshooting
http://support.apple.com/kb/HT2090

My 4s camera flash light wont turn off and camera is not working

my 4s camera flash light wont turn off and camera is not working

Hello there, Shantae2231.
You may just want to try resetting your phone per the instructions in this Knowledge Base article (There is no data loss by performing this step):
iOS: Turning off and on (restarting) and resetting
http://support.apple.com/kb/ht1430
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

I need to caputre image by camera and projector that emit light when i snap.

My PC have two VG Cards(one attached to monitor and one attached to projector) with two display,one IMAQ card(PCI 1407) and CCT Panasonic Camera with video output signal. I can caputre image using IMAQ Card with camera but I need to caputre image by camera and projector that emit light when i snap.
Question (1): from labview application, how to control projector that emit light when i snap picture.
Anyone can help my problem? Thanks you.

Sorry I can not answer your questions.
I would like to suggest that you re-post this question to the LabVIEW >>> General discusion page. You will get have a larger audiance on that list.
This list is intended to discuss LabVIEW Real-Time which is a version of LV that runs under Pharlap and is intended for applications that require deterministic control over program execution.
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Cameras and Camcorders FAQ

There are many questions that people have when it comes to digital cameras and camcorders, but thankfully there is also an abundant amount of useful information to be had. These are the most frequently asked questions, and hopefully this information will help you out in your purchase and use of your digital camera or camcorder!
Which digital camera should I purchase?
I feel like the quality of the construction is the most important consideration when purchasing a digital camera and unless you are on a tight budget or you need the camera to be compact, I would suggest looking into purchasing a DSLR. There is much more information on what to consider when purchasing a new digital camera here.
My camera LCD is not displaying my images! What do I do? Most often this is due to the camera having its image review setting turned off, but it can, of course, be due to a defect in the camera or damage to the screen. I would first read your manual to see how to set your image review setting, and if that doesn’t work I would try resetting the camera back to its default settings. If you are still having problems, I would suggest having the camera looked at by an authorized service technician.
How come my lens won’t come out of the camera body when I turn the camera on? This is most often caused by damage to the internal mechanism inside the lens or something stuck inside the lens. You could try blowing compressed air into the side of the lens in hopes of dislodging whatever might be stuck in the lens. If that doesn’t work, you could try putting the camera on a flat surface with the lens pointed upwards, hold the shutter button in, and then press the power button. If neither of these two things work, I would have the camera looked at by an authorized service technician.
Why do my photographs always come out blurry? Blurry images are most often caused by the camera being moved while the image is being taken and a not using a flash during the exposure. I would suggest setting the shutter speed to a faster setting (if your camera has this capability), turning the flash on, or putting the camera on a tripod. Blurry images could also indicate that the camera was not focused properly. When taking an image with a digital camera, you should always depress the shutter button half-way so the camera can achieve focus, and once the focus indicator on the screen (or in the viewfinder) shows that focus has been achieved, press the shutter button down the rest of the way. There, of course, could be something physically wrong with the camera, but this is most often not the case. If your blurry images persist, I would have the camera looked at by an authorized service technician.
Which camcorder will meet my needs? Things to consider when deciding which camcorder will meet your needs are what format they record to, what type of sensor they use, how large of an optical zoom the camcorder has, how they record sound, if the camcorder has image stabilization, if it performs well in low-light situations, and the type of viewing system it uses. There are, of course, other considerations and you can read a detailed description of these features here.
How do I get my videos onto my computer? Most often this involves connecting the camcorder to your computer with a cord (eg. a firewire cord), putting your DVD into your DVD drive, or directly connecting your memory card to your computer with a card reader. Most camcorders come with software that allows the user to view and edit their videos, but keep in mind that there is more advanced software available for purchase which may produce better results. You should also make sure that your computer has the necessary codec’s installed to allow your software to play your videos.
How do I burn my edited videos to a DVD so I can play them on my TV? If the software you are using to view and edit your videos doesn’t allow for this, you are going to need to invest in software that does. You are also going to need a DVD drive in your computer that has the ability to write to a DVD, and I would suggest starting with blank DVD-R discs.
Do I need a High Definition (HD) Camcorder for my videos to play on my HDTV? No, you don’t need a HD camcorder for your videos to play on your HDTV, but if you want to take full advantage of the resolution your TV is capable of, you would need to record your videos in HD.
I accidentally deleted images from my memory card! Can I get my images back? The answer to this is a resounding maybe. When you delete an image on a memory card (or format the memory card), you are not actually getting rid of the image file. What actually happens is the path assigned to that file is deleted, allowing the digital camera to write over it, and unless you take more images and write over the deleted image, it is possible to recover the image. You would need to get an image recovery program, but keep in mind that just because one photo recovery program fails to recover you images, it doesn’t mean that a different program will also fail.
Can my camcorder be used to take still images? Most camcorders purchased today have the ability to record still images, but keep in mind that a camcorder is not designed for still imagery and usually captures very low resolution images. Most camcorders also have the ability to copy a frame from a video and render it as a still image, but once again the quality doesn’t compare to the results you would get with a digital still camera.
For much more information on digital imaging and all sorts of helpful videos on the subject, go to BestBuy.com and look under the Cameras & Camcorders tab. I hope this helps out!
Allan
Community Connector
Best Buy® Corporate
Message Edited by Allan-BBY on 01-21-2009 04:55 PM
Allan|Senior Social Media Specialist | Best Buy® Corporate
Private Message

Thanks for pointing that out -- yeah, I see my error. I just did a little bit of web searching and it's not AVCHD. This seems to pretty well summarize it:
http://www.camcorderinfo.com/content/Samsung-SC-HMX10-Camcorder-Review-34476/Format.htm
"The Samsung ... outputs video in the H.264/MPEG-4 format (the file extension is .MP4). This highly-compressed video codec should not be confused with the competing AVCHD format. AVCHD is a type of H.264/MPEG-4 codec, but the version Samsung employs is different, with both benefits and drawbacks.
"...the MPEG-4 video ... is adequate. ... this type of MPEG-4 is space efficient and less processor-intensive to edit than AVCHD."
...and...
http://www.camcorderinfo.com/content/Samsung-HMX-H105-First-Impressions-Camcorder-Review-3 6130/Compression-amp-Media.htm
"The Samsung HMX-H105 records video in the MPEG-4 AVC/H.264 format, the same as models from the previous years. MPEG-4 has clearly been adopted as the format of choice for HD camcorders, split into two camps. Sony, Canon, Panasonic, and most recently JVC, all use AVCHD, which is a subset of AVC/H.264. AVCHD experienced some serious stumbling blocks in its first few years, as existing hardware and software choked on the heavy data loads. It has, however, gotten much better in the past year. AVC/H.264 is also data-heavy, at least compared to old standard definition camcorders, but the format is easier to read. QuickTime can work perfectly with the files, and has the benefit of being free and dual-platform."
I know this aspect has all been covered to death on these forums in the past, with respect to PE7 (which chokes on any Samsung .MP4 file I throw at it). While I've bookmarked the workaround posted by you in this thread (thanks!), I was hoping to avoid the extra steps à la native compatability with PE8.

Copying folders and Subfolders with files using Promises WinJS

Hi,
I have app written in WinJS.
I want to copy a particular folder along with its subfolders and their files. I am so far successful with copying folders. Below is the code for the same.
app.CopyFolder = function (folder, destFolder) {
var replace = Windows.Storage.CreationCollisionOption.replaceExisting;
//console.log("create folder: " + folder.name);
return destFolder.createFolderAsync(folder.name, replace).then(function (newdest) {
return app.CopySubFolders(folder, newdest);
app.CopySubFolders=function(folder, destFolder) {
return folder.getFoldersAsync().then(function (folderlist) {
return WinJS.Promise.join(folderlist.map(function (folder) {
return app.CopyFolder(folder, destFolder);
Now after I have copied all the folders I need to copy their respective files. The problem is I am stuck,I get the files copied but I want to proceed ahead after all the files are written to their respective folders. Below is the code for the same.
app.copyAllFiles = function (fileList, destStorFolder) {
console.log('copyFiles Start...');
var promises = [];
var fileCopied = 0;
var collideOpt = Windows.Storage.CreationCollisionOption.replaceExisting;
return WinJS.Promise.join(fileList.map(function (file) {
return app.copySingleFile(file, destStorFolder);
app.copySingleFile = function (fileObject, destFolder) {
var promises = [];
var fileCopied = 0;
var path = destFolder.path + "\\" + fileObject.folderName;
var collideOpt = Windows.Storage.CreationCollisionOption.replaceExisting;
return Windows.Storage.StorageFolder.getFolderFromPathAsync(path).done(function (folderObjectOfLocalFolder) {
return fileObject.fileObject.copyAsync(folderObjectOfLocalFolder, fileObject.fileName, collideOpt).then(function (fileObject) {
console.log("copied single file:" + fileObject.name);
The problem is when i run the folder copy code and apply breakpoint for the success call back of
CopySubFolders(source,destination).done(/*my breakpoint*/)
The folders are created.
But when I try to breakpoint for my copyAllFiles,the files are created only when i pass the success call back.
Can anyone tell me what am i doing wrong? How can I proceed ahead only when all the files are written successfully.
Regards,
Ninad

Hi,
I tried the above solution but what i want is that the action of copying folders and subfolders along with the files should be done with promises and that promise should return only when all folders,sunfolders and their files have been copied. I want to
do it in this way because I want to perform certain second action only when all things are copied.
If I do it the as per the link the function runs in the background and my second action proceed aheads and may cause error if it finds some folder or file missing.
So I came up with following above code,first copy folders then copy. The copy folder works as expected but the files are getting copied only when the file copying code enters the success call back.
Can you please shed light on my code where I am going wrong.
Or is it ok to proceed ahead with the solution you mentioned at the link cause I dont want any runtime crashes.
Regards,
Ninad

Camera and ipod shuffle do not show up on desk top when connected

Kodak camera and ipod shuffle do not show up on desk top when connected. Trying to download pictures and adding my music to ipod shuffle, Anyone have any suggestions.

Have you plugged in another USB device to ensure that the USB ports are working?
Suggest you buy (about $10 - $20) a USB memory card reader. Just plug your camera's memory card into it & copy the pic files to your Mac. Quicker & easier than interfacing the camera for pic transfer.
 Cheers, Tom

I edited photos in photo shop that I took off of my camera and then whenI was done I saved them in a folder in my documents as a JPEG. Now when I try to open them there is an encrytion error me assage.

I edited photos in photo shop thay I took off my camera and when I was done I saved them in a folder in my documents as a jpeg. now when I try to open them there is an encryption error message

The folks here would need far more information from you before they provide help.
You know the drill: Exact OS...PS version...etc. The more you provide, the better.
What is the exact message that is displayed?
What have you tried so far?
Do the files display on your browser? In Bridge?
What are you doing when it happens?
Are the files still on your cameras card? If so and,you copy one to your desktop and save it without changes, does it reload properly?
Don't worry about providing too much information. Every little bit helps.

Material exchane ,copy pricing and conditions from main item to sub item.

Hi All,
We are using parts exchange/interchangeability in the transaction ME22N,
While using ME22N we are exchanging main item with interchangeable part and while doing so we want to copy pricing and conditions from main item to sub item.
But its not happening.
As per sap help its possible, details describe below.
http://help.sap.com/erp2005_ehp_04/helpdata/en/c2/0a5288b77d11d3bcce00105ab03aee/content.htm
Price Determination by Copying from Main Item
In the case of price determination by copying from the main item, the net price of the originally ordered part is still used for the superseding part in a part exchange.
The system copies all conditions from the main item to all sub-items and takes into account the order quantity for the main item when calculating scale prices. It does not take into account the conditions and scale prices that exist for the interchangeable part.
You cannot change the conditions, which have been copied from the main item, at sub-item level. It is possible, however, to define additional conditions for each sub-item.
Prerequisites
A calculation schema, which can be altered on an individual basis in Customizing, has been supplied for the price determination.
In the vendor master record, you have set the schema group 09 (interchangeable material).
But in customizing I didnu2019t find value 09 for schema group .
Can any buddy through some light on missing pieces which need to be set?
Thanks
Regards
Ritesh

Hi,
Can you check few more things and tell me?
- In this exit, does XVBPA and XVBAP contains all the line items. ( main and sub items ).
- In Sales order creation time, do these table have VBELN populated when this exit triggers.
- If you modify XVBPA or XVBAP in this exit, do they get overwritten after that.
Try this code. See if it works. Let me know if you still have a problem.
DATA: wa_hvbpa LIKE vbpa,
      wa_xvbpa like vbpa.
CLEAR: wa_hvbpa, wa_xvbpa.
* check if HVBAP and VBAP line items are not same
IF vbap-posnr <> hvbap-posnr.
* read the ****-to partner from main-item
READ TABLE xvbpa INTO wa_hvbpa WITH KEY posnr = hvbap-posnr
                                          parvw = 'WE'.
IF sy-subrc = 0.
*   read the line item data for sub-item based on main item
    READ TABLE xvbap WITH KEY posnr = vbap-posnr
                              uepos = hvbap-posnr.
* See if current line is the child of that BoM parent
    IF sy-subrc = 0.
      MOVE wa_xvbpa-kunnr TO xvbpa-kunnr.
      MOVE xvbap-vbeln TO wa_xvbpa-vbeln.
      MOVE xvbap-posnr TO wa_xvbpa-posnr.
      MOVE 'WE' TO wa_xvbpa-parvw.
      MODIFY vbpa FROM wa_xvbpa.
    ENDIF.
ENDIF.
ENDIF.
Regards,
RS

I would like to copy music and audio books that I downloaded from cds from my ITunes to my Smartphone. Does anyone know how to do this?

I would like to copy music and audio books that I downloaded from cds from my ITunes to my Smartphone. Does anyone know how to do this?

you would have to read the directions that came with your smartphone to learn how to put content on it.
Itunes syncs with Apple devices.

I want to get another 4s and use it not as a phone, but only as a video camera and editor and hook it up only with wifi. i would sync it to itunes so i can pay for apps and upload. would this work, or must it be connected to a phone carrier?

I want to get another 4s and use it not as a phone, but only as a video camera and editor and hook it up only to wifi. i would sync it to itunes so i can pay for apps and upload. would this work, or must it be connected to a phone carrier?

Trust me when I say this coming from 20 years of experience.
Get a powered external drive, format it 1 Partition Option: GUID and OS X Extended Journed as the format in Disk Utility.
Download and install Carbon Copy Cloner, clone internal drive to external drive.
Set a schedule to remind you to do it at least once a week, keep it near your charger.
When you plug your charger in, do plug the clone and power the machine up, set the display to sleep only,
CCC will do the rest.
If you want to boot from it, hold the option/alt and select it Startup Manager.
I've seen many TimeMachine and TimeCapsule nightmares and so far haven't seen a problem from anyone using a bootable clone.
It's simple, it's easy, it's more reliable and more powerful than what Apple does and it only takes plugging in a extra cable.
Make as many clones as you want, keep them time seperated, off site etc. etc.
Cables don't have network issues, clones can be verified in seconds merely by booting from them.
Clones protect your productivity, your up in seconds on a clone despite even the hard drive dying.
Software problem? No sweat, boot of the clone and reverse clone your problems away.
If you want to fuss and muss with half implemented TimeMachine and TimeCapsule network headaches then prepare to suffer.
I don't like to suffer, I bought a Mac not to suffer, but it appears you do with TimeMachine and TimeCapsule.
Most commonly used backup methods

Copying cameras and lights

Similar Messages

Maybe you are looking for