Copying routing through workbench

SAP Gurus,
When I copy a routing through workbench, system is automatically recreating a BOM for that material. Now I have two BOMs for that material, which I don't want. I cant use CA03 because I am using parameter effectivity for BOMs and routings. Is there any way that system copies the routing with out recreating the BOM.
Thanks
Bobby

resolved

Similar Messages

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

Problem in dynamic routing through ESB

Hi All,
I am trying dynamic routing through ESB, So I created routing service in my esb with WSDL of BPEL Process1 and a soap service with same wsdl. Then created a xsl transformation. In this xsl transformation I added below code to route to BPEL process 2.
<xsl:variable name="LocationIn"
select="http://PC-HP249:8888/orabpel/default/SyncBPELProcess2/1.0/SyncBPELProcess2"/>
<xsl:variable name="LocationOut"
select="ehdr:setOutboundHeader('/shdr:ESBHeader/shdr:location',
$LocationIn, 'shdr=http://xmlns.oracle.com/esb;')"/>
But when I am invoking this ESB through another BPEL process, Got below error message:, Is there any solution for that , I am using 10.1..3.4.0, (JDEV, and BPEL).
receiveInput
[2010/02/25 17:50:39] Received "inputVariable" call from partner "client" More...
View xml document
Invoke_1 (faulted)
[2010/02/25 17:50:39] Faulted while invoking operation "initiate" on provider "PartnerLink_1".less
-<messages>
-<input>
-<Invoke_1_initiate_InputVariable>
-<part xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" name="payload">
<SyncBPELProcess1ProcessRequest xmlns="http://xmlns.oracle.com/SyncBPELProcess1"/>
</part>
</Invoke_1_initiate_InputVariable>
</input>
<fault>
ORABPEL-08034
JTA Rollback requested.
The current JTA transaction has been aborted due to rollback request received from partner invocation.
</fault>
</messages>
</sequence>
[2010/02/25 17:50:39] There is a system exception while performing the BPEL instance, the reason is "Namespace prefix 'http' used but not declared.". Please check the error log file for more infromation. Please try to use bpel fault handlers to catch the faults in your bpel process. If this is a system exception, please report this to your system administrator. Administrator could perform manual recovery of the instance from last non-idempotent activity or dehydration point. More...
oracle.xml.xpath.XPathException: Namespace prefix 'http' used but not declared.
     at oracle.xml.xslt.XSLBuilder.startElement(XSLBuilder.java:468)
     at oracle.xml.parser.v2.XMLElement.reportStartElement(XMLElement.java:3703)
     at oracle.xml.parser.v2.XMLElement.reportSAXEvents(XMLElement.java:3564)
     at oracle.xml.parser.v2.XMLElement.reportChildSAXEvents(XMLElement.java:3576)
     at oracle.xml.parser.v2.XMLElement.reportSAXEvents(XMLElement.java:3566)
     at oracle.xml.parser.v2.XMLElement.reportChildSAXEvents(XMLElement.java:3576)
     at oracle.xml.parser.v2.XMLElement.reportSAXEvents(XMLElement.java:3566)
     at oracle.xml.parser.v2.XMLElement.reportChildSAXEvents(XMLElement.java:3576)
     at oracle.xml.parser.v2.XMLDocument.reportSAXEvents(XMLDocument.java:1537)
     at oracle.xml.jaxp.JXSAXTransformerFactory.newTemplates(JXSAXTransformerFactory.java:379)
     at oracle.tip.esb.server.service.EsbTransformer.getXSLTTransformer(EsbTransformer.java:147)
     at oracle.tip.esb.server.common.cache.TransformCachePolicy.loadEntry(TransformCachePolicy.java:50)
     at oracle.tip.esb.server.common.cache.Cache.setEntry(Cache.java:306)
     at oracle.tip.esb.server.common.cache.Cache.setEntry(Cache.java:270)
     at oracle.tip.esb.server.common.cache.Cache.getEntry(Cache.java:208)
     at oracle.tip.esb.server.common.cache.Cache.getEntry(Cache.java:181)
     at oracle.tip.esb.server.common.cache.RuntimeCache.getXSLTransformer(RuntimeCache.java:324)
     at oracle.tip.esb.server.service.EsbTransformer.doTransform(EsbTransformer.java:101)
     at oracle.tip.esb.server.service.EsbTransformer.transform(EsbTransformer.java:90)
     at oracle.tip.esb.server.service.EsbTransformer.transform(EsbTransformer.java:83)
     at oracle.tip.esb.server.service.EsbRouterSubscription.transform(EsbRouterSubscription.java:388)
     at oracle.tip.esb.server.service.EsbRouterSubscription.onBusinessEvent(EsbRouterSubscription.java:208)
     at oracle.tip.esb.server.dispatch.EventDispatcher.executeSubscription(EventDispatcher.java:138)
     at oracle.tip.esb.server.dispatch.InitialEventDispatcher.processSubscription(InitialEventDispatcher.java:545)
     at oracle.tip.esb.server.dispatch.InitialEventDispatcher.processSubscriptions(InitialEventDispatcher.java:527)
     at oracle.tip.esb.server.dispatch.EventDispatcher.dispatchRoutingService(EventDispatcher.java:94)
     at oracle.tip.esb.server.dispatch.InitialEventDispatcher.dispatch(InitialEventDispatcher.java:160)
     at oracle.tip.esb.server.dispatch.BusinessEvent.raise(BusinessEvent.java:1988)
     at oracle.tip.esb.server.dispatch.BusinessEvent.raise(BusinessEvent.java:1467)
     at oracle.tip.esb.wsif.WSIFOperation_ESB.executeRequestResponseOperation(WSIFOperation_ESB.java:288)
     at oracle.tip.esb.wsif.WSIFOperation_ESB.executeInputOnlyOperation(WSIFOperation_ESB.java:357)
     at com.collaxa.cube.ws.WSIFInvocationHandler.invoke(WSIFInvocationHandler.java:472)
     at com.collaxa.cube.ws.WSInvocationManager.invoke2(WSInvocationManager.java:437)
     at com.collaxa.cube.ws.WSInvocationManager.invoke(WSInvocationManager.java:251)
     at com.collaxa.cube.engine.ext.wmp.BPELInvokeWMP.__invoke(BPELInvokeWMP.java:826)
     at com.collaxa.cube.engine.ext.wmp.BPELInvokeWMP.__executeStatements(BPELInvokeWMP.java:402)
     at com.collaxa.cube.engine.ext.wmp.BPELActivityWMP.perform(BPELActivityWMP.java:199)
     at com.collaxa.cube.engine.CubeEngine.performActivity(CubeEngine.java:3698)
     at com.collaxa.cube.engine.CubeEngine.handleWorkItem(CubeEngine.java:1655)
     at com.collaxa.cube.engine.dispatch.message.instance.PerformMessageHandler.handleLocal(PerformMessageHandler.java:75)
     at com.collaxa.cube.engine.dispatch.DispatchHelper.handleLocalMessage(DispatchHelper.java:217)
     at com.collaxa.cube.engine.dispatch.DispatchHelper.sendMemory(DispatchHelper.java:314)
     at com.collaxa.cube.engine.CubeEngine.endRequest(CubeEngine.java:5765)
     at com.collaxa.cube.engine.CubeEngine.createAndInvoke(CubeEngine.java:1087)
     at com.collaxa.cube.engine.delivery.DeliveryService.handleInvoke(DeliveryService.java:546)
     at com.collaxa.cube.engine.ejb.impl.CubeDeliveryBean.handleInvoke(CubeDeliveryBean.java:342)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at com.evermind.server.ejb.interceptor.joinpoint.EJBJoinPointImpl.invoke(EJBJoinPointImpl.java:35)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.interceptor.system.JAASInterceptor$1.run(JAASInterceptor.java:31)
     at com.evermind.server.ThreadState.runAs(ThreadState.java:693)
     at com.evermind.server.ejb.interceptor.system.JAASInterceptor.invoke(JAASInterceptor.java:34)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.interceptor.system.TxRequiredInterceptor.invoke(TxRequiredInterceptor.java:50)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.InvocationContextPool.invoke(InvocationContextPool.java:55)
     at com.evermind.server.ejb.StatelessSessionEJBObject.OC4J_invokeMethod(StatelessSessionEJBObject.java:87)
     at CubeDeliveryBean_LocalProxy_4bin6i8.handleInvoke(Unknown Source)
     at com.collaxa.cube.engine.dispatch.message.invoke.InvokeInstanceMessageHandler.handle(InvokeInstanceMessageHandler.java:37)
     at com.collaxa.cube.engine.dispatch.DispatchHelper.handleMessage(DispatchHelper.java:140)
     at com.collaxa.cube.engine.dispatch.BaseDispatchTask.run(BaseDispatchTask.java:58)
     at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:650)
     at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:675)
     at java.lang.Thread.run(Thread.java:595)
[2010/02/25 17:50:39] BPEL process instance "260032" cancelled
Regards

In below I changed http://PC-HP249:8888/orabpel/default/SyncBPELProcess2/1.0/SyncBPELProcess2 to http://PC-HP249:8888/orabpel/default/SyncBPELProcess2/1.0 . this is working.
<xsl:variable name="LocationIn"
select="http://PC-HP249:8888/orabpel/default/SyncBPELProcess2/1.0/SyncBPELProcess2"/>

Can't get internal vSwitch to route through external vSwitch to connect to Internet using one NIC on 2012 R2 Datacenter with Hyper-V

I'm running into a bit of a problem here.
I have the following two virtual switches setup on one 2012 R2 Datacenter Physical Host w/ one (1) physical NIC:
Physical Host is running 192.168.50.120, GW: 192.168.50.1, SM: 255.255.255.0 (Cisco Router has the IP of 192.168.50.1). The Internal vSwitch Network (will contain 8 VM Servers) is 192.168.1.1. I want the VM Servers on 192.168.1.1 to be able to get Windows
Updates by being able to route through the 192.168.50.1 vSwitch but yet, still want the Networks segregated.
Both of these virtual switches/networks will be running through one NIC.
I initially setup RRAS to use NAT but I'm not sure if this is the correct configuration. It seemed to work but when I went to Activate my Product Key (via MSDN Subscription) it wouldn't recognize the key and therefore I couldn't run windows updates.
However, when I set up two of the VMs on 192.168.1.1 to use DHCP through the 192.168.50.1 Network it would work fine (i.e. DHCP, DNS and GW were all set to 192.168.50.1).
Any ideas on what I might be doing wrong or how I could setup an effective route between the two networks?
Any and all ideas are most welcome and appreciated.
Sincerely,
Wallace
Wallace Davis

Hi nbk5533,
The external virtual switch and internal virtual are isolated, you must set RRAS to connect both network zone, you can refer the following article to connect the internal
switch and external virtual switch.
Configuring Hyper-V for multiple subnets with only one NIC (Server 2008 R2 Edition)
http://blogs.technet.com/b/letsdothis/archive/2012/01/08/configuring-hyper-v-for-multiple-subnets-with-only-one-nic.aspx
The similar thread:
RRAS in VM
http://social.technet.microsoft.com/forums/windowsserver/en-US/486bcbb4-bf01-4946-b103-cd896e9dafb9/rras-in-vm
More information:
http://msdn.microsoft.com/en-us/library/windows/hardware/gg605194(v=vs.85).aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Not able to access CAS service through Endeca workbench: getting an error "CAS Console must be accessed through Workbench"

Getting an error while accessing the Datasource tab through Endeca workbench "CAS Console must be accessed through Workbench". Verified both ws-extensions.xml and casconsole.properties files which exists under %ENDECA_TOOLS_CONF%/conf, both files shares the same sharedSecret. Do anybody knows how to resolve this issue.
I did tried to reinstall CAS component multiple time , all the time the same error throwing.
Endeca CAS service is also not able to start through microsoft console (services.msc) throwing an error " Windows could not start the Endeca CAS Service service on Local Computer"

This can occur if CAS is reinstalled. Check your ws-extensions.xml and casconsole.properties files, and ensure that they agree on the same shared-secret.
Best
Brett

Internet speed drops 85% when routed through WRT160NL

I have a WRT160NL, and it decreases my internet speed from 3700kbps down to 550kbps when I route through it.
My ADSL modem is connected via ethernet cable to the WRT160NL, then I have an ethernet cable from port#1 of the WRT160NL to my desktop computer. With this connection, I get a download of about 550kbps.
When I route directly from my ADSL modem to my desktop (bypassing the WRT160NL) my download speed is 3700kbps. I've checked all cables and connections. What is causing the speed to drop by 85%?
thanks,
groff5
Solved!
Go to Solution.

As you are facing the problem on your Hardwired computer, then you change the settings on your Router... Once you login to the Router setup page.. Below the Setup you will find MTU size which will be set to AUTO so you need to change it to Manual and change the Size from 1500 to 1365 and click on Save Settings..... Then click on the Security tab and Disable "SPI Firewall" and Uncheck "Filter Anonymous Internet Requests" and click on Save Settings...
Now you need to power cycle your Network... Unplug the Power from the Router and Modem, Wait for 30seconds and then plug the Power to the Modem, Once all the Lights are lid on the Modem then Plug the Power to the Linksys Router...
Now you can check the Speed, what the speed you are getting it on your Computer....
If you still face the same problem then i think you need to upgrade the firmware of your Router.. Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop....
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Copy Route Error

When I try to use the Copy Route function it does not work correctly. I select my source group and the previewed area is much larger than the desired source group. The copy route function appears to be selecting nearby vias that are not associated with that parts group. Has anyone seen this problem? It is very difficult to use the copy route function when you are always having to delete vias that become scattered over the board surface. Perhaps this is an issue NI needs to address in future versions.

Copy route is a complete PITA to use, I see it as a completely useless feature....
If you really want to replicate paths that are constant for what looks like some type of spectrum analyzer or equalizer filtering. I did the following:
Select the trace and via filters, disable all others......select trace area, copy > paste, the virtual outline will allow you to real time place the results and watch for any DRC errors in placement in real time, when happy release.....this pic took 12 seconds to do all 4.
Is this what you are trying to do?
Signature: Looking for a footprint, component, model? Might be here > http://ni.kittmaster.com
Attachments:
SS001.png ‏41 KB

"CAS Console must be accessed through Workbench" problem

Hi, the data sources tab is not able to connect to the cas server and giving off this message : CAS Console must be accessed through Workbench
I have encountered this before and bookmarked the the solution page that was from eden but now that it is down I can't get to it. Can anybody remember the solution? thanks!

This can occur if CAS is reinstalled. Check your ws-extensions.xml and casconsole.properties files, and ensure that they agree on the same shared-secret.
Best
Brett

Router won't connect comps to the net, can't acess router through comps either!!

Hey, umm... I was playin a game for a bit, and suddenly I got booted off the net. I thought it was the game just spiting me (WoW does that sometimes. It hates everyone), but it turned out to be the internet.
I called comcast, confirmed that my internet was ok, and decided to call linksys.
I went to the tech support via phone, dialed the number, and the number is telling me it can't connect the call.
So, I came here.
Now, normally I can always get into the router via my comp to see what the deal is with it. This time though, I can't even acess it!
It tells me it couldn't connect every time I try to get into it, from all the computers.
I figured it could just be a bum wire messin with me. So I went into the closet and pulled out a new one that I had just got. That one didn't work either.
Then I took one of the wires I knew worked (because it connected the computer to the modem and got online fine), and plugged it in. It didn't work either.
So frusterating...
Anyways, I upgraded the routers firmware the other day after hearing that it would give me more port fowarding slots (It DESPERATLY needs more), and all was well up until now.
It's been about 5 days since I did that, so I don't know what woulda caused this to happen all of a sudden.
Espically not being able to get to the router through a computer. That's just weird...
Well, if anyone knows anything, lemme know.
Also, let me know if the phone support comes back up some time soon.

On a side note, im not using the wireless function, and I have it turned off in the settings.

How to access to configuration page of the router through the windows phone 7 ?

Hi all
I'd like to know if there's a way to access to configuration page of the router through my windows phone 7.
I usually access the router by laptop as following: "192.168.1.1". but sometimes when I'm on my phone I need to reboot the router through my phone other then the laptop which is not near me...
I looked up for applications that should do the work, but unfortunately I got no positive result, so I'm reaching out to this very forum in order to find help and tricks so that I can figure it out
thank you in advance

Hi Happydz,
For help using Windows Phone please post in the Windows Phone forums on
http://answers.microsoft.com .
The MSDN Windows Phone Development forums are for developers to discuss writing their own Windows Phone apps.
That said, I'd expect you could connect to 192.168.1.1 from the phone's browser the same way you would from the laptop's browser.

Why is my traffic being routed through china

While connecting to a voice server located in Europe, I realised that I have a ping of 300 where I previously got around 20ms or less
So I did a traceroute, turns out my traffic is being routed through china, to cyprus and then to Europe, for what purpose?
traceroute to ts109.light-speed.com (216.127.64.68), 30 hops max, 60 byte packets
1 192.168.1.254 (192.168.1.254) 0.573 ms 0.760 ms 0.957 ms
2 213.120.155.226 (213.120.155.226) 8.748 ms 8.480 ms 9.688 ms
3 213.120.155.158 (213.120.155.158) 10.892 ms 11.330 ms 12.163 ms
4 host109-159-245-114.range109-159.btcentralplus.com (109.159.245.114) 14.495 ms 14.859 ms 15.933 ms
5 31.55.164.221 (31.55.164.221) 16.301 ms 17.112 ms 17.982 ms
6 31.55.164.109 (31.55.164.109) 18.316 ms 9.854 ms 10.631 ms
7 acc2-10GigE-0-2-0-6.bm.21cn-ipp.bt.net (109.159.248.236) 14.412 ms acc2-10GigE-0-3-0-7.bm.21cn-ipp.bt.net (109.159.248.246) 9.506 ms acc2-10GigE-0-2-0-6.bm.21cn-ipp.bt.net (109.159.248.236) 13.672 ms
8 109.159.248.48 (109.159.248.48) 20.637 ms 109.159.252.206 (109.159.252.206) 21.238 ms 109.159.248.132 (109.159.248.132) 20.103 ms
9 peer2-xe-4-3-0.telehouse.ukcore.bt.net (109.159.252.53) 21.590 ms peer2-xe10-1-0.telehouse.ukcore.bt.net (109.159.254.116) 18.727 ms peer2-xe0-0-0.telehouse.ukcore.bt.net (109.159.254.102) 22.750 ms
10 t2c3-xe-0-1-2-0.uk-lon1.eu.bt.net (166.49.211.166) 20.753 ms 21.500 ms t2c3-xe-0-2-2-0.uk-lon1.eu.bt.net (166.49.211.174) 25.339 ms
11 i-0-4-0-7-peer.ulco-core02.pr.telstraglobal.net (134.159.95.25) 23.243 ms 27.041 ms 18.730 ms
12 i-0-5-1-3.istt-core02.bx.telstraglobal.net (202.84.249.234) 202.289 ms 198.248 ms i-0-0-4-3.istt-core02.bx.telstraglobal.net (202.84.249.2) 230.943 ms
13 i-0-4-0-3.skdi-core01.bi.telstraglobal.net (202.84.219.185) 213.259 ms 225.674 ms 225.800 ms
14 i-0-2-0-8.hkth-core01.bx.telstraglobal.net (202.84.141.137) 261.573 ms i-0-2-0-5.hkth-core01.bx.telstraglobal.net (202.84.141.141) 249.423 ms i-0-2-0-8.hkth-core01.bx.telstraglobal.net (202.84.141.137) 261.567 ms
15 i-0-0-0-3.hkth12.bi.telstraglobal.net (202.84.153.182) 247.201 ms i-0-0-0-2.hkth12.bi.telstraglobal.net (202.84.153.178) 260.094 ms 247.396 ms
16 unknown.telstraglobal.net (134.159.100.98) 280.081 ms 278.679 ms 279.570 ms
17 ae6.dar01.hkg02.networklayer.com (50.97.19.33) 280.926 ms 268.843 ms 282.005 ms
18 119.81.138.139-static.reverse.softlayer.com (119.81.138.139) 277.294 ms 119.81.138.131-static.reverse.softlayer.com (119.81.138.131) 279.524 ms 119.81.138.139-static.reverse.softlayer.com (119.81.138.139) 267.113 ms
19 xe1.cr1.hkg01.light-speed.com (119.81.152.250) 290.360 ms 291.142 ms 277.008 ms
20 * * *
21 * * *
22 * * *
23 * * *
24 * * *
25 * * *
26 * * *
27 * * *
28 * * *
29 * * *
30 * * *
Here's a screenshot of a traceroute done only a few months ago
Same origin, same destination, only 270MS less latency.
I have been forced through this dumb route for a couple weeks now, why?
EDIT: Should point out, it's only when connecting to this server, all other routes are fine

light-speed/teamspeak clearly have a complex infrastructure, which probably does some form of dynamic server allocation.
Maybe they have moved their server addresses around and you still have a fixed reference to a server that was appropriate but is not any longer, and if you reset your application it would reassign you to a different one.
This demonstrates they have a complex infrastructure with nodes in various places: doesn't show exactly what it is or how to deal with it.
When I do tracert ts109.light-speed.com it comes back with Tracing route to ts109.teamspeak3.com [216.127.64.68]
ping light-speed.com gives 23 ms
ping teamspeak3.com gives 304 ms
ping ts115.light-speed.com
Pinging ts115.teamspeak3.com [94.101.84.61] with 32 bytes of data&colon;
Reply from 94.101.84.61: bytes=32 time=112ms TTL=41 <<< not as helpful as 23, but better than nearly 300

Unable to login to Switch & Router through secondary Acs ,when primary ACS is down.

Dear All,
i have configured primary ACS in DC data center and secondary ACS in DR data center, i have configured replication , and it is working well, but when we put down primary ACS , we are unable to login in switch and router through secondary ACS , i ahve dedicated link between core dc sw to core dr sw through which all traffic is getting replicated . All user , mgmt vlan are created in FWSM firewall.Kindly help.
Regards
Amit Kulshrestha

Hi Bro
I'm assuming you've configured your ACS correctly and the Cisco network devices correctly. Perhaps, this could be a bug. The reason I say this is because last week, I was implementing 2 units of Cisco ACS 1121 v5.3 (in HA mode) for a client, and i had similar issues myself. When I down the primary ACS, I'm unable to login to my network devices, eventhough my secondary ACS is UP and PINGable from all network devices.
Hence, I downloaded and applied the latest cummulative patch from the CCO website 5-3-0-40-4.tar.gpg (Release Date: 27/May/2012) and my problem solved.
Perhaps, your ACS version isn't 5.3, but the morale of the story here is, maybe patching is required for your case!!
Please do let me know the outcome. May the force be with you, bro!

Video iChat problem using AIM (Routing through 2nd NIC)

routing iChat for AIM
I have a Mac Pro with both ethernet cards connected. ethernet zero is connected to my office network and ethernet one is connected to a back channel DMZ. I do not have Access to the office router and it's been configure to prevent chat. I have added routes to the table for ethernet 1and am able to chat through AIM with my wife on the iMac at the house with no issues. However when I establish a video connection it errors out. I've made sure that I have both the initial and establish connection IP's routing through my back channel. But it doesn't seem to work. If I turned off the office LAN, I have no problem connecting using video chat.
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 172.24.187.251 UGSc 22 288 en0
64 192.168.0.1 UGSc 0 0 en1
74.124/16 192.168.0.1 UGSc 0 0 en1
74.124.211.219/32 192.168.0.1 UGSc 1 0 en1
127 localhost UCS 0 0 lo0
localhost localhost UH 1 608 lo0
169.254 link#4 UCS 0 0 en0
172.24.187/24 link#4 UCS 10 0 en0
gx280image 0:19:b9:12:64:93 UHLW 0 0 en0 1166
minint-fcnjr5if 0:18:8b:1b:26:7e UHLW 0 11 en0 1077
minint-a07t9r69 0:15:c5:7:d9:18 UHLW 0 0 en0 1194
172.24.187.21 localhost UHS 0 194 lo0
172
172.24.187.251 0:0:c:7:ac:82 UHLW 18 427 en0 119
192.168.0 link#5 UCS 8 0 en1
192.168.0.1 0:9:5b:f6:96:ac UHLW 4 9 en1 1151
192.168.0.2 0:6:5b:90:c2:4b UHLW 0 44 en1 1155
192.168.0.17 0:21:e9:93:3:1d UHLW 0 0 en1 1057
192.168.0.23 0:1b:77:12:f0:6a UHLW 0 8 en1 997
192.168.0.25 0:21:e9:65:c6:33 UHLW 0 0 en1 513
192.168.0.44 0:21:e9:8f:23:7c UHLW 0 0 en1 1056
192.168.0.48 localhost UHS 0 7 lo0
192.168.0.255 link#5 UHLWb 1 100 en1
192.168.73 link#8 UC 1 0 vmnet1
192.168.73.255 link#8 UHLWb 1 89 vmnet1
192.168.222 link#7 UC 1 0 vmnet8
192.168.222.255 link#7 UHLWb 1 89 vmnet8
205.188.0/16 192.168.0.1 UGSc 2 0 en1
209.85.201.125/32 192.168.0.1 UGSc 1 0
Show the following established connections when trying to use video chat.
Proto Recv-Q Send-Q Local Address Foreign Address (state)
tcp4 0 0 192.168.0.48.50922 64.12.30.68.5190 ESTABLISHED
tcp4 0 0 192.168.0.48.50918 205.188.8.179.5190 ESTABLISHED
tcp4 0 0 192.168.0.48.50917 209.85.201.125.5223 ESTABLISHED
tcp4 0 0 172.24.187.21.50915 172.24.195.103.80 ESTABLISHED
tcp4 0 0 172.24.187.21.50914 172.24.195.102.80 ESTABLISHED
tcp4 0 0 192.168.0.48.50227 74.124.211.219.993 ESTABLISHED
tcp4 0 0 192.168.0.48.50225 74.124.211.219.993 ESTABLISHED
tcp4 0 0 192.168.0.48.50223 74.124.211.219.993 ESTABLISHED
tcp4 0 0 192.168.0.48.50221 74.124.211.219.993 ESTABLISHED
udp46 0 0 *.16402 .
udp4 0 0 *.55928 .
udp4 0 0 *.5351 .
udp4 0 0 *.5350 .
udp4 0 0 127.0.0.1.49728 127.0.0.1.49728
udp4 0 0 172.24.187.21.123 .
udp6 0 0 fe80::225:ff:fee.123 .
udp4 0 0 172.24.187.21.138 .
udp4 0 0 172.24.187.21.137 .
udp4 0 0 192.168.0.48.138 .
udp4 0 0 192.168.0.48.137 .
udp4 0 0 192.168.73.1.138 .
udp4 0 0 192.168.73.1.137 .
udp4 0 0 192.168.222.1.138 .
udp4 0 0 192.168.222.1.137 .
udp4 0 0 *.138 .
udp4 0 0 *.137 .
udp4 0 0 *.52460 .
udp4 0 0 *.53118 .
udp4 0 0 *.62551 .
udp4 0 0 *.64698 .
udp4 0 0 *.57696 .
udp4 0 0 *.58110 .
udp4 0 0 *.62845 .
udp4 0 0 *.50647 .
udp4 0 0 *.59899 .
udp4 0 0 *.57346 .
udp4 0 0 *.56231 .
udp4 0 0 *.631 .
udp4 0 0 192.168.0.48.123 .
udp4 0 0 *.60623 .
udp4 0 0 *.60450 .
udp4 0 0 *.64265 .
udp4 0 0 *.49597 .
udp4 0 0 *.54901 .
udp4 0 0 172.24.187.21.49410 .
udp4 0 0 172.24.187.21.49373 .
udp4 0 0 *.2223 .
udp4 0 0 *.53391 .
udp4 0 0 *.64030 .
udp4 0 0 *.57804 .
udp4 0 0 *.56795 .
udp4 0 0 *.54587 .
udp4 0 0 *.62597 .
udp4 0 0 *.61433 .
udp4 0 0 *.49535 .
udp4 0 0 *.50679 .
udp4 0 0 *.49810 .
udp4 0 0 192.168.73.1.123 .
udp4 0 0 192.168.222.1.123 .
udp6 0 0 fe80::223:dfff:f.123 .
udp6 0 0 ::1.123 .
udp4 0 0 127.0.0.1.123 .
udp6 0 0 fe80::1%lo0.123 .
udp6 0 0 *.123 .
udp4 0 0 *.123 .
udp6 0 0 *.5353 .
udp4 0 0 *.5353 .
udp4 0 0 . .
icm4 0 0 . .
icm6 0 0 . .
icm6 0 0 . .
as I said I can still chat, I just cannot use video chat unless I disconnect the office network. I need to leave the office network as the default route. Suggestions would be appreciated, not sure if iChat problem or routing problem.

Umm,
Not so much as a Bug but a feature.
iChat has been designed with a level of security in-built.
When you send a Visible Invite it is just that, away to trigger the other end to pop up a window.
iChat then engages in the SIP part which includes a text based connection method called SIP (Session Initiation Protocol).
This involves a behind the scenes invite and a check to see that the IP the Visible invite went to is the same one the SIP bit ios going to. (remember you can log in as many times as you wanton different apps and computers to the AIM servers), but is essentially to make sure you are connecting to who you invited.
This SIP Process is very much like an old fashioned operator call in that you call the operator they call the operator at the other end who calls the Buddy, he answers his operator who confirms he is willing to chat... etc.
As with a telephone call you want to make sure you are talking to the right person.
Like a telephone iChat has to be in "one place" in relation to the internet.
Unlike a corner plot house it can not have one "number" in one street and another in the side road (even local authorities and postal service ignore this).
The process in other IM apps is mixed.
Skype spreads it's connection over as many hosts as will accept them meaning your call could be using 30 or 40 other end users to spread that load.
Of course this also increases the ports in use giving you less security overall.
Some do seem "better" at ignoring secondary connections the way Web Browsers do.
10:33 PM Tuesday; June 30, 2009

Routing through master channel

Hi Guys,
I want to use the master channel to add some final compression to my mix but it appears not to be working e.g. sliding the volume fader on master has no effect on the songs volume.. what's the best way to check that everything's being routed through master properly?
cheers.

You can't add compression on the master fader. It is for volume only, no plugs.
To compress your mix: Be sure everything is routed to the same pair of outputs (1/2) and add compression there.

When I hook up router through modem, no internet, modem only internet ok

Okay, so we decided to shut off our home phone since everyone only uses cells now. But wanted to keep our SBC dsl line and upgrade it to the faster connection. So, phone line gets shut off, no internet for a few hours, as expected, but after 5 hours I called in to tech support at which time they told me they had to walk me through setting the modem back up again so we could get back online. First question, is your computer hooked up to the internet via a router? They required that I disconnect the router before they could proceed because they do not support routers, unless it is one of theirs. No other options given. So I went through the process with them and was back online. But only I, on the main computer, could get back online since the router was not connected. We have two other computers here, both use wireless adapters, one is a desktop in another room the other is a laptop.
Now, when I go in and set up all the wires as instructed, all the lights come on properly indicating that I should be connected, but whenI try to pull up a page or do anything that requires me to be connected, I'm getting error messages that I can't connect to the internet. When I go into the control panel and look at the network connections, says I'm connected.
Everything is fine if I just want to get internet access for this one computer and only use the modem. But if I want to get everyone else online using my Linksys WRT300N Wireless-N Broadband Router then I have problems and absolutely no internet for anyone.
Any help appreciated. I've got a child who homeschools and does all of her work online so it is imperative that we resolve this as soon as possible.

With most SBC (AT&T) setups, the modem does the PPPoE login for you. The modem can do this because it is actually a modified modem-router. So in most cases, your WRT300N would need to be set to an "Internet Connection Type" of "DHCP - automatic" (not PPPoE).
To make this change in your router, power down your entire network.  Disconnect the WRT300N from the modem and all other devices. Next, using an ethernet cable, connect one computer to a LAN port on the WRT300N. Power up the WRT300N. Power up your computer. Login to the WRT300N at 192.168.1.1 , then set the "Internet Connection Type" to "DHCP - automatic". Click on the "Save Settings" button, then wait (3-60 seconds) for the screen to refresh. Power down the WRT300N and your computer.
Next, using an ethernet cable, connect the modem to the Internet port of the WRT300N. Leave one computer wired to a LAN port on the WRT300N. If your modem has a USB port, do not connect anything to it. Power up your modem and allow it to fully boot. Power up your WRT300N and allow it to fully boot. Power up your computer. Now try your Internet connection. It should work.
If you still have trouble, please do the following:
1) Please state the make and exact model number of your modem (not the WRT300N).
2) Please do the following test:
Power down your entire network. Using an ethernet cable, connect your modem directly to your computer.   (We will not be using the WRT300N during this test.)   Power up your modem and computer. If your computer has a wireless adapter, turn it off. Verify that you have a working Internet connection, then do the following:
Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig /all" (with no quotes), then hit the Enter key. Copy the results to your next post. To do the copy, highlight the results, then use the copy (Ctrl-c) keys and the paste (Ctrl-v) keys. If your "IP address" does not start with 192.168 , then for security reasons, erase the last half of your IP address from your post.

Copying routing through workbench

Similar Messages

Maybe you are looking for