Core 2 Duo Firewire will not power up Fireface 400 audio device

I recently replaced my MacBook Pro Core Duo 15" by a MacBook Pro Core 2 Duo 15".
The Core 2 Duo does not power up nor recognize my FireFace 400 ( www.rme-audio.com/english/firewire/ff400.htm ) wether plugged in the firewire 400 or 800.
I went to a Mac Store to check if the problem was with my Mac. It turns out that the same problem occurs with all MacBook Pro Core 2 Duo 15" and 17" in the store.
According to the tech. at apple store, it has to do with the firewire chip set, and that they can't do anything about incompatibility with the fireface 400...
Are you aware of this problem and is there a workaround.
Thanks

I haven't tried with a voltage meter, however I have tried with another known working power brick from the same model Mini and it still doesn't work. We bought two of these for the household when they came out, which has helped with troubleshooting.

Similar Messages

MacBook 2,1 Core 2 Duo (2006) Will Not Charge Nor Recognize The Batter

I currently have a MacBook 2,1 Core 2 Duo from 2006. I have an issue with the battery not being recognized, not charging, and it being at "0%". I have tried doing an SMC Reset twice. It did not help with this battery issue. From what I understand, quite a bit of people are having this issue but I haven't seen one that was not solved by an SMC.
For additional details here is a better source of my computer- http://bit.ly/1B12az4
Here is what it says under "Power"
Charge Information:
Charge remaining (mAh): 0
Fully charged: No
Charging: No
Full charge capacity (mAh): 0
Health Information:
Cycle count: 0
Battery Installed: No
Amperage (mA): 0
Voltage (mV): 0
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Current Power Source: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
ID: 0x0100
Wattage (W): 60
Revision: 0x0000
Family: 0x00ba
Serial Number: 0x0027e5c7
Charging: No

Hi wadesie,
Thank you for using Apple Support Communites.
I found two articles that should be of use for you to sort out why your computer is not recognizing the battery. The first is general battery troubeshooting.
Mac notebooks: All about batteries - Apple Support
Regarding not recognizing the battery it says:
My battery is not recognized
If the battery in your MacBook, MacBook Air, or MacBook Pro is fully drained of power, the battery will put itself into a low power state to preserve its ability to charge in the future. Connect your Mac Notebook to AC power and allow it to charge for at least five minutes. If the connect to power screen persists after charging for five minutes, reset the SMC.
The next article provides instruction on resetting the SMC.
Intel-based Macs: Resetting the System Management Controller (SMC) - Apple Support
Regards,
Jeff D.

HT1212 what if ipod will not power down

what if ipod will not power down

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If you can't do the above then
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

My ipod touch will not power on or even be acknowledged by my computer when i plug it in, any suggestions to the problem

My Ipod will not power on, it is fully charged and if I plug in into the computer it doesn't even ackowledge it. Any suggestions?

Try a hard reset and go from there.
Basic troubleshooting steps.
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G + 120G OCZ Vertex 3 SSD Boot HD 

Hi, I have a macbook pro 17" 2.4ghz intel core 2 duo 2007, will upgrading to Yosemite slow me down or create problems with my Iphone or other app ?

Hi, I have a macbook pro 17" 2.4ghz intel core 2 duo 2007, will upgrading to Yosemite slow me down or create problems with my Iphone or other app ?

Yes, i do not suggest upgrading right now. There is some software malfunction or glitch that spontaneously shuts down this specific model. I upgraded and it was a pain to downgrade and make my mac usable again.

My MacBook Pro shut it self down and will not power up

It shut itself down and will not power up. Battery was charged

I have (had) a brand new late2013 13" MacBook Pro that my wife and I really splurged on. It had the 512 gb (over 500, I know that) SSD hard drive, improved processor, and chose to stick with 8 gb of ram. In other words, we dropped close to $2000 on that notebook.
Within a week, it started doing what you are explaining. In fact, during one of the forced shutdowns, I was prompted to send an error message to apple. My wife wanted nothing to do with it, but I chose to anyway. Thankfully I did. When I couldn't take the frustrating shutdowns anymore I took it to the apple store.
AWESOME PEOPLE!!!! Granted I have been a PC guy my whole life. That started to change with my first really thick iPod in 2002. Slowly, the iPad and Apple TV made appearances in my house. My wife (an artist) then came in the picture and I am now and have been an apple guy, w/o the window sticker of course. My interaction with the apple store workers only increased my stoke.
SEND ERROR MESSAGES TO APPLE IF PROMPTED TO DO SO.
As I said, I went against wife and sent one to apple. The apple tech was able to figure out what was wrong immediately considering a copy was kept on my MBP, and because it was day 30 (really was) since purchase, he switched out with BRAND NEW UNIT! No refurb, no hassle!
All was fine until it did it again. Basically, if my computer sat on but was idle, it would go to sleep as we had instructed it to do in the energy savings preference page. Normally, to reawaken MBP, all we needed to do was tap space bar.
Like the first one we traded in, no luck. We would actually have to try and power up with power button, and even the apple techs found it frustrating as we had. Thankfully it did it in front of them as well.
Now is the kicker. Our contact felt incredibly bad, along with store manager, that this was now the third visit we have had to make involving a brand new computer. The manager wanted to make it up to us. I feel like her solution went so far beyond my expectations, I will never own another brand again.
She took all of our merchandise we bought for the 13" MBP, (bag, 12 south vertical stand, etc) and let us pick what ever replacements we wanted for the 15" MBP she was giving us. YEP, A 15"!
due to the fact that we specifically purchased the larger SSD in the 13", the entry level 15" did not offer the larger SSD drive. That saint of a manager moved us into the quad core, I7 with 16gb of ram!!! The only stipulation is that we pay for the apple care. When I thought it was truly over, she had one last surprise and charged only the difference between the apple care prices.
Good things happen to everyone else, always. Happy to report I finally had my turn.
I am not saying you will make out as well as I did, but if it is shutting down, especially in the first 30 days of ownership, send every report to apple it asks you to (for ease of retrieval by Mac employee) and trust they will do right by you. New computers should not shutoff for no reason, and the great thing is, they agree!
Considering my initial purchase for my 13" MBP came to around (off my head $1850 with apple care).
I now own the very high end $2599.00 15" because the SSD hd was comparable to mine.
I can't stress this part enough. I NEVER ONCE RAISED MY VOICE! I was a little upset but never complained once. I was completely understanding and never asked for anything above getting the first computer I paid for to work properly.
THANK YOU APPLE!!!!!THANK YOU APPLE!!!!! THANK YOU APPLE!!!!!
Bring your faulty computer in, send all error messages to apple, and most importantly remember that the young 22yr old standing in front of you there didn't build it. It's not his fault. Work with him with respect and apples philosophy will shine brightly.
FWIW, all of the service techs I spoke with at the Genius Bar are very aware of this situation and all feel an update is headed down the pipeline soon.
Good luck all!

T60 suddenly switches off, will not power on again, DVD drive related?

I have searched and searched for this, and although finding many "T60 will not power up" I haven't
found any with this twist.
My T60 is ~2 years old, and the problem just started recently. Working on battery one day, the laptop
suddenly died - like instant loss of power. I could not turn it on again. One strange thing though:
When I removed the battery and re-inserted it, the batt-icon-light came on briefly (a blink). If I then pushed the power button it lit up for 1 sec and then went out, not booting. Repeating it, without removing the battery, it didn't light up.Ok, thinking maybe the power supply was dead, I took it completely apart, removing also the harddrive and the DVD drive. By chance I then saw that it had "fixed itself". I resembled it and it worked again, powering up like nothing had happend.
Then it happened again yesterday. I read in here about the "push power 10 times, hold power down 30 sec" etc, but had no luck with that. Again, when I inserted the adapter cable the light came on (power plug + batt light) but when pushing the power button they went off, and if I removed and reinserted the plug same thing again.
I then read about removing HDD and DVD drive, and that did it! So, it happened again today and this time I just removed the DVD - and it booted again.
So, after this loong description here I hope that some of you have tried/seen this before or have an idea what it can be. I left the DVD drive out, and it has not happened again...yet (it's been 5 hours only).
Ideas?
Thanks in advance!
Martin.
Moderator edit: Removed duplicate copy of message text.

Kaz wrote:
Hi Nordal,
I know this is an old thread, but since I too am now experiencing inability to startup by T60 and seems to be getting worse in the last months, I was wondering what additional things you may have learned in the last 2 years since facing this issue. My system will typically be in standby or hibernate and when I open lid to start it up again, Power and Bat light go out and cannot start it. No beep codes, nothing. Previously, recovery was to pull battery (which is now new Lenovo as of last month and working great), hit power button a few times and then hold it in, put battery back in and AC adapter, then it would start up. In last few days, this no longer works. I have to go through similar step, but now I have to startup only with battery, once in Desktop, I can plug in adapter and no issue until next time. I have three 90W AC adapter all putting out correct 19.5-20 VDC. Have rulled out an adapter issue, I believe. Concerned about something on motherboard being flaky, but cannot pinpoint issue. A few days ago when this happened, I had to pull CMOS battery, wait a few min., then put everything back together and was able to boot.
Have never pulled anything more than RAM, CMOS battery, main battery, and AC adapter. May have to try DVD drive next time.
Thanks,
Kaz
It's probably best to start a new thread instead of reopening one thats 2-3years old, but from what your describing it sounds like your slowly ruling out everything except the system board, nothing you don't know already.
I don't normally deal with T60's, my main focus is T61, but I do have a source for the boards if you were to need one, as well as having a source to get the older boards reflowed. Some of the older models had problems with solder connections cracking when the board would flex, which can be repaired on an infrared reballing machine. My friend Dominic (realblackstuff from thinkpadforums.com) operates a website where boards are collected and sent off to be reflowed in wholesale lots. It's quite reasonably priced, as are the T60 boards pulled form grade "A" corporate laptops, but lets hope you can find a lesser component that is causing the problems.
ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)

My Powerbook will not power up, but I can hear the fan running...

Please help!! My Powerbook will not power up, but I can hear the fan running when I press the power button to attempt to power it up. I just received a new power adapter because it wasn't working properly and it was doing this before and then it worked for a week and now it will not power up at all. It just starts the fan but nothing else turns on. When I plug the adapter, with the battery still connected, it will look as if it is charging but then the light on the plug turns from green to orange then off and doesn't power up at all. If I take the battery out and plug in the adapter, the light stays on but it does not power up except for the fan noise. Does anyone have any suggestions? I also followed the two articles listed online in regards to resetting the power setting and the command + alt + P + R as well. Nothing works. Thanks in advance.....

Same here. If I start up with the power adapter attached, it starts up fine. If I try to start up from battery only, the fan comes on, the sleep light comes on but nothing else happens. I tried letting it sit that way for about 15 minutes and nothing changed. I tried attaching the power cord while in this mode and nothing changed. I tried the PMU reset a couple of times but nothing helps.
This computer is just over 1 year old and I have not had any problems with the power cord (3rd party), the battery, or any problem like this before. It started after a proper shutdown last night and attempt to start without the power cord this afternoon.
Any answers to this yet? I think I'll call on this and report any success to this discussion.
15" PowerBook G4 Mac OS X (10.4.8) 1 GB DDR2 SDRAM, 100 GB HD

Need Help HP DM3 (DM3-1130us) Laptop will not power on. No power at all except for light on a/c jack

Hello, I need some help.
I have a HP DM3-1130us Laptop that will not power on at all.
the only thing that happens when I plug it in is the power jack lights up.
When the power button is used absolutely nothing happens.
No power, no fans, no leds, no on/off cycles, no beebs, absolutely nothing
just the light by the power jack that says the cord is plugged in.
The laptop has Windows 7, 320gb hdd, 4gb ram.
I have tried new power adapter and still nothing.
I have taken the battery out and tried and nothing.
I've tried the option where you take the battery out and hold the power and nothing.
I have tried with different hard drive and no hard drive and nothing.
I have tried reseating the ram and tried new ram modules still nothing.
So I am kind of stumped on what to do, the laptop will just not turn on.
Its not under warranty anymore so cant send it off.
It has not been exposed to any elements(extreme heat or water).
and its never been dropped or anthing.
Im kind of wondering maybe the power button board its self is bad?
If feels fine, its not loose or anything but could it
have just stopped working? for those who are not familiar with this model.
the power button is on the side and is a kind of drag and release button.
Its also on the same board with the Wifi button and 2 Usb ports.
But Im wondering before I buy a new one if this is what it could be.
Or could the motherboard its self be bad?
But even if the motherboard is bad would it still power up
just not post?
Also does anyone know of any other way to try to power this laptop up
without using the slide button. I mean kind of like off a Dv6000 you can power the laptop on by using the Quicklaunch buttons on top but this laptop does not have those.
If anyone can provide any information I would appreciate it.
Thank you.

Hey Tyler,
Unfortunately it is difficult to troubleshoot this type of issue. The majority of the time when the computer wont power on with the same symptoms you described, the power supply board is faulty. Most of the time if the motherboard is bad it should at least turn on or so some signs of life. Like I said, this is most of the time. Sometimes it could do exactly what your experiencing. I would suspect the power supply board has failed since you are not receiving any sort of lights, sounds, etc.
You could check the motherboard for swollen capacitors or loose solder joints but sometimes you wont be able to find anything.
I hope this helps answers your questions,
Sean
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

My iPhone 5s will not power on and I need my serial number for support.

I am attempting to get help through Apple Support- Chat, but I need my serial number. It is not showing up in iTunes under the device preferences. Any other ways to retrieve the serial number through iCloud?
If anyone has any idea of what is going on with my phone, I would love some assistance. I live 45 minutes from the nearest Apple Store. Here's the situation:
About 2 weeks ago, my phone started shutting itself off and restarting randomly.
About a week and a half ago, I would randomly get a blue screen and then the phone would restart multiple times.
About a week ago I turned off Touch ID in an effort to resolve the issue, after reading some fixes from this community. That seemed to help. I do have the animation turned off, so I had read that there may be an issue between the Touch ID and animation reduction. If that had not helped, I was going to turn the animation back on.
Last night my phone seemed fine. I did hear it restart in the middle of the night once, but this morning it will not power on at all.
I tried connecting it to my computer through iTunes, but iTunes does not see it and I cannot access the device information from it.
My phone is less than a month old, and for the first two weeks it worked great. I am taking it into the AT&T Store today where it was purchased, but I don't really have high hopes for a resolution.
Any help is much appreciated!

Sorry AT&T store won't be much help.
I suggest you make an appointment with the Genius bar and then go to the Apple store.

Macbook Pro will not power on without battery installed

Hi there,
I have a Macbook Pro A1226 that fails to power on without a battery installed.
i.e. will not run off AC power on its own. I have tried 2 other power adapters, no change. All 3 adapters are outputting the correct voltage without fluctuations.
But, if I am in OSX with a battery plugged in, shutdown the laptop, remove the battery while AC is still plugged in, it will power back on without any issues. But as soon as I remove the battery, it will not power back on using just AC.
Is this an I/O board issue, or a mainboard?
I have power drained the unit and reset the parameter ram.
Thanks

Any update on this? This is the same thing that's going on with my laptop right now. I was at the Genius Bar and they said they can send it in for repair. Takes 7-9 days and costs a minimum of $310. At the time I was there, my computer wouldn't start up at all, because the battery had drained to less than 20%. It didn't even start with just the power cord (no battery in). The "genius" finally got it to work by doing a PRAM and SMC reset. Got home and was able to recharge my battery to 100%. Used my computer for 2 days before I dared to take it off the power supply. Lo and behold, as soon as I take it off the power cord, then re-connect it, it shows "Not Charging". I tried to do SMC again, but no luck. Keeps saying "not charging". Even tried with a brand new battery. Do I have to get the I/O board thingy replaced?

Ipod touch generation 5 will not power on

My ipod touch generation 5 will not power on though it was showing to b e fully charged. I have been pressing and holding the on button on the top which usually cause a the screen to light up. Is there some way to get it to work?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

My IPOD Touch initially had a white screen. I tried correcting this by restoring default settings via ITunes. The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB

My IPOD Touch initially had a white screen. I tried correcting this by restoring default settings via ITunes. The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB. I get an error on my PC stating that device attached to USB port is not recognizable. Can anyone help?

Error 1602: Try the following steps to resolve this error:
Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
Follow the steps listed for Error 1604.
This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
Above from:
http://support.apple.com/kb/TS3694

HT4061 I cannot switch my IPAD on and it will not power up - i had this problem before and cannot remember how we fixed it?

Can anyone help us please?
I cannot switch my IPAD on and it will not power up - i had this problem before and cannot remember how we fixed it?

Press and hold both the home button and lock button until the apple logo shows up.

My HP Pavilion dv9700 will not power up. Lights blink on and off on a cycle, but screen is black

My HP Pavilion dv9700 will not power up. Lights blink on and off on a cycle, but screen is black.

Please post your Full Product Number
http://h10025.www1.hp.com/ewfrf/wc/findModel?lc=en&dlc=en&cc=us

Core 2 Duo Firewire will not power up Fireface 400 audio device

Similar Messages

Maybe you are looking for