Core center info

Can some one point me in the right direction for some user info for core center.
I did a test run last night and stopped it after it slowly turned my FSB up to 300mhz a 50% increase!!! So I turned it off quick!!
So if some one can point me in the right direction I would be very

I cicked on Auto and the FSB counter on the lieft sow moved up to 300 mhz the only other thing was the coloured 'bar' in the center moved from eft to right in each cycle then +1 added on to the FSB.
Do I have to enable core center in the bios for it to work????

Similar Messages

Cool-n-quit/core-center

in CnQ my cpu fan gives me an alarm above 3000 rpm's. Whatever I change in the setup, this won't stop. The fan speed alarm in set to 10.000
Temperature is just 36 degr for CPU and 37 for system
Any thoughts?

Hi everyone. As you can see I'm kind of a newb and I have some related questions. First off some background. I've done hardware installs, harddrive clean formats and swaps, etc. I was planning on building my own computer, but order one from cyberpowerinc.com. I haven't done a profile yet but will after this post so by the time you read this my system should be listed below. Anyway, in the BIOS I had cool and quiet disabled because in the manual it says to check serial numbers of chips before running it, and I didn't want to mess with pulling the heat sink , etc. to check my serial number. This morning while investigating a noise issue (high, varying frequency, buzz) I noticed in Core Center that it was related to CPU fan RPM (low RPM). I then found the program called speedfan, which allowed me to varify this, as Core Center wasn't real accurate. Using speed fan I was able to run the fan at 100% and got no buzzing. Below 70-80% I did though. I then found this thread and realized Core Center could do this (by clicking on Core Center) in another thread. So is the Cool and Quiet mode in Core Center the same as in the BIOS, because I thought if I disabled in the BIOS it would be disable, come to find out Core Center was running it (and causing the bad noise when the fan cycled to low RPM), it wasn't however slowing the CPU speed.
So basically, I hate the buzz at low fan speed, can I just run my fan at max through Core Center? Is there another program that will allow me to run a min fan speed, but cycle say from 100% to 80%? Is it even worth that cycling if only down to 80%? Should I just set it to max or 7/8 manually? Are the BIOS and Core Center Cool and Quiet settings related?
Any info you think will be useful to me, please let me have it. Thanks.

Core Center under XP with user-rights only

I am using WIN-XP SP2 prof.
I have installed core-center in latest version.
Everything is alright, when i am logged in as a Admin.
But when i login as a normal user I can not start Core-Center via
Startup-Folder.
I don't want give the Admin-password to other users.
What can I do ?
Peter

Some other possibilites:
1. You can have the complete information if the data is submitted in FDF, XML, or XFDF. I opened the submit box in AA7 and noted the settings. The fact I can open it in AA7 was a bit surprising. The reason I suggest the data files is that they do not require extended rights and can simply be impored to the form on your end to get the identical results as if the whole form had been sent.
2. I could only play the media file, but that is likely a capability of AA7 rather than an issue with flash and such.
3. E-mail may be an issue. Some systems require additional work to be able to use E-mail for form submission. Prior to AA9, mailto require MAPI on the client machine.
Don't know if any of these help or not, but at least they are some more tidbits of info.

P965Neo-F V2 MSI Dual Core Center Support

Hi.
I brought MSI P965Neo-F v2 MB and MSI 7600 GT graphic card, now i installed Dual Core Center and it shows only Graphic card info, is it some bug? i tryd core center and it showd me alot wrong info, like no cpu fan, sys fan 5k rpm and +12v was 24v. Anyone else having trouble whit DualCoreCenter utility?

all other utilitys lie, 12v shows 24v, 3v shows 0,12, cant be real, and no fans at all:D

NTune or Core Center or Digicell

Hi
since Core Center and I assume even Digicell have doubtful reputation I would like to ask if enyone has done some experiance with NVidias "nTune"?
On nVidias site there is a info that nTune is NOT compatible with K8N Neo4 Ultra.
On MSI site I could reed that it IS.(compatible)
I really do not know if this has to do with different versions, but they are comming from NVidia.
Thanks

Quote
Originally posted by SAB
I don't use any of that software. MBM5 is a good program if you feel the need to sporadically check your vital signs. I think support for it has been discontinued though. When I first complete a system build....I will "burn" it in for a few days. I will usually run some intensive benchmarks, and then check the CPU and GPU temps with a temp gun, or back into Hardware Monitor in BIOS for a quick look.
As far as overclocking goes....best to do it the old-fashioned BIOS way!!!
If your CPU isn't getting overheated in those situations, it usually is a good sign that you don't need to run all that "iffy" software to verify temps anyway. However, if you are overclocking either the CPU or GPU, then a good program to monitor temps is a good idea.
For everyday casual use of your system.....and if your applications of thermal paste are within DIY parameters, you should be able to do without on-board temp monitors!!
Yeah... what he said!
SpeedFan is still an ongoing/evolving work if you feel a need to know from the desktop.... it pretty much jibes with the BIOS H/W monitor.
And all you new Neo2 Plat guys out there - remember the cold start temp reporting bug - it will read high (4-6C) until you restart, then it'll display "correct" temp after - or as correct as the on board sensor will get
As long as your temps don't get into the high 50C's range at load, nothing is likely to fry....

Over clocking using core center

over clocking using core center
ok rather a noob at this and thought I would try a safer way of overclocking.
The program ticked away up til 300mhz on the left hand monitor at which point I turned it off as a 50% increase in the FSB seemed rather too much.
Has anyne used this prog or can point me to any documents about what it does!

thanks for the info.
the page below.... seems to show that you can over clock from core center on the desk top do I have to change bios setting to manua to alow it to work or is the review a bit
http://www.digital-daily.com/motherboard/msi-kt6-delta/index05.htm

P6n diamond/dual core center

Hello, I am having a hard time getting this installed correctly(dual core center). After I get it installed it only shows info for my 8800 card none for my motherboard displays a error message saying m/b driver did not install. Ntune installed the first time but only shows limited info, after uninstalling both utility's n tune won't reinstall and core does the same as before. Any help would be great!

Sorry for the lame no info post above! I have filled out my signature with my system info, let me know if there is anything else I should put in.
I could not find what version of DCC I am using but I hope it is the latest because MSI live update is telling me it is current.
Where can I find the Moan guide you mentioned in above post?

Dual Core Center listing varied FSB in vista

I've had it list the FSB as 467 and 1000, and I don't know if it should be doing that or why it's doing that. When I ran it in XP the FSB was always 200

Quote
or why it's doing that
The first explanation that comes to mind is the usual one: Dual Core Center is far from being the most perfect, flawless, accurate and compatible application. The second explanation that can be added to the last one is: Vista is not exactly the cream of the pie either.
If you have more questions, it would probably not be a bad idea to give us some info about your system (read the >>Posting Guide<< first) and tell us which version of DCC your are actually using. Another important thing you should not keep to yourself, is your Vista Version (32bit or 64bit).

Transfer Game Center info from Store ID to iCloud ID

Hi!
I would like to know if there is a way to transfer all my Game Center info from my Store ID (google account) to iCloud ID (me account). This must include all my achievements, save data and progress, nickname and friends.
On the other side, I have a doubt about the games that sync theirs progress through iCloud. Because my Game Center is not linked to iCloud, where these games store the info?
For example, Cut the rope syncs its progress apparently through iCloud but I can not find any file on my iCloud storage. I have checked on the iCloud storage info in my iPad Settings and also in the Mobile Documents on my Mac Library. Maybe I'm not suppose to see those files but I guess that if the data of the game is on iCloud it won't be difficult to migrate Game Center to iCloud because iCloud have already my data...
I don't know if I'm clear enough....
Thanks in advance.

I have tried doing just as you have asked with my partner, but failed.
My gamecenter ID is my appleID. This seems to be the biggest problem.
It turns out that when we transfered my gamecenter ID to her newly created ID (Can be done in gamecenter) that it makes her newly created ID the appleID in the whole process. A big BUHBOW! We tried many different ways to get it to work but in the end I had to have her transfer back to my apple ID. ALL BACK TO NORMAL with my cloud! , you have no idea
Try it yourself, but if you used the same Gamecenter ID as your Apple ID be prepared to use the new account as your Apple ID.
It isn't supposed to be that way either, the GC transfer is supposed to do achievements and saves (in GC cloud only and not if saves are local(although there are depressing workarounds on the net for those)). I had iTunes support verify this whole process while I hammered them 'this wont affect MY appleID?', they say no it shouldn't. But testing this out first hand proved otherwise.
As I said, it may be different if your GC ID is not the same as your Apple ID.
I now have my partner cursing half eaten worms about Apple.
I will be back on to support tomorrow about this.
EDIT: I just re-read what you wrote and actually, you can only transfer the GC ID to a NON existing email account (just to be clear I mean to apple, the email can exist just not in any apple accounts anywhere). That is, the whole process of the transfer creates a NEW account and can't be tied in to any account but then adds it to your account when done. If so you get 'Account is already in use'. That part I had itunes support delete my partners apple id to have try this all out (she wasn't using it anyways so nothing lost there). Doing the transfer adds the new email addy to your account but it sets it as primary for the account. (As I said if yours is the primary like mine is for GC and the AppleID)
I believe the whole transfer is worth staying well clear of for now. The issues we had were bad, but I managed to get everything back the way it was albeit many password changes later.
Message was edited by: gene77

Dual Core Center working in Vista but not XP on a dual boot system?

Hi All.
My system specs are:
Dual Boot Windows XP Pro SP2 and Windows Vista Ultimate
Temps for CPU in Vista averaging at 43 - 45 degrees in XP averaging at 38 to 42 degrees. It never seems to go much higher than 53 on Load.
Thermaltake Soprano tower
MSI K9N Diamond Motherboard
Hiper 580watt Modular PSU
4GB OCZ Gold 6400
AMD X2 6000+
2 X 300gb diamond maxtor 10 HDD
MSI Geforce 7800gt
DVD Rom
LG Dual Layer DVDRW+/-
I am running a dual boot system with Windows XP Pro SP2 on one partition and Windows Vista Ultimate on the other. Both operating systems seem to be operating properly except for an odd situation with Dual Core Center. In Windows XP Dual Core Center only indicates the Mainboard properties - No VGA, whereas on Windows Vista Ultimate Dual Core Center indicates both VGA & Motherboard properties. I have installed MSI Nvidia drivers for the Graphics card & also tried straight Nvidia drivers for the card but it has made no difference VGA will not show up in XP. Yet on installing Dual Core Center on the Vista partition VGA showed up immediately. Can anyone help.
If anyone can come up with an answer to this it would be a real help.
Many Thanks in advance.

have you try to update/install the dual core driver from amd?

MSI P35 NEO & dual core center problem

hi, i have a problem with my motherboard msi, Bios 1.2 and the dual core center 2.0.0.8 ,since days ago, the msi dual core center 2.0.0.8 so many times shows fan speeds alerts false alarms from the cpe temp, for that reason, i upgraded the appl to 2.0.1.6 ( the last),i set the oc level to 25% like with the older version, but time later the pc crash and put a black crash screen and it dont let me to overclock my cpu , i get back to 2.0.0.8 but the fan alarm dont stop, and i dont know if the newer version fix this problem
any help?
sys specs
msi p35 neo bios 1.2
core 2 quad q6600
2 gb value ram
psu duck

right, but i like to use msi dual core center, because i dont like to have the pc overclocked all the time, anyother suggestion for this?
thanks for the reply

NX7600GT Diamond Plus and fan speed with Dual Core Center

I just got a NX 7600GT Diamond Plus for my HTPC. I noted that Riva Tuner and other utilities are not able to control the fan speed of the video card. The only way one can control the fan speed is via Dual Core Center and 3D Core Cell. The problem is that the default setting for fan speed on Dual Core Center is too high and clearly audible. How can I get Dual Core Center to start with user defined presets during windows start-up/boot-up ?
What I want to do is to put the fan into 'SILENT' mode automatically during Dual Core Center start-up. Any ideas / suggestions ?

Quote from: BOSSKILLER on 17-January-07, 00:44:11
well no need to edit manually, MSI provided everythink in easy way from core center.
select advanced mode, create your custom profile pickup your desired settings,(setup maximum FAN RPM via buttons) and save it to custom profile.
suggest you to read help section from program.
So the custom profile is automatically loaded every time DualCoreCenter starts up ? Maybe there is something wrong with my install of DCC, I cannot get it to load custom profiles automatically upon startup. I can save the changes to say "User Profile 1" but the profile active on startup always is the "default" profile ...

Alarm going off in core center

I have an alarm going off in core center Theres a red arrow next to wherer it says 12 v. then in the white box it says 10.95 v any one know what it means and what I could do about it I don't know whats normal for the readings I get in core center. My pc has been locking up and certian games wont load unless it's really cool in the room.

Good questions! Some folks have acceptable readings with CoreCenter, by verifying them with the Hardware Monitor (in BIOS). I compared them with my SpeedFan program, and as far as temps go..I use a laser temp gun to check CPU, case, and video card temps. Voltages on the PSU can be verified with a voltmeter of course. The specifications on your NB fan should be in your manual. Or you can check out this thread at Anandtech:
http://forums.anandtech.com/messageview.aspx?catid=29&threadid=1513370&STARTPAGE=2&enterthread=y

Core Center Related

I am getting:
1st Line: Vcore 1.49V
2nd Line: 2.91V
3.3V under line 2
3rd Line 5.03
5V under line 3
4th Line 12.08v
12 under line 4
and the alarm goes off, I am very new and would be most thankful for any help.

First off if the computer is working and stable you don't want to change any of those. Second Core Center is the wrong place to change any of those values unl;ess it is for a specific test. I don't ever recommend making any changes with Core Center for any reason. In fact I don't recommend Core Center at all.
Best to restart with Stock values and if you are looking to play around ask first so that you knopw what changes to try and make and how to test it to see if any changes have the correct affects.
LOL Now I sound like I am talkking down to you. I know that but I can not know what level of knowledge you have. If what I said offends you please forgive me. I am just trying to help someone I don't know and over the internet to boot. That is never really that easy to do.

Core Center displays in fahrenheit?

Ok, this might be a dumb question but I can't find the answer. I have a K8N Neo Platinum and A64 3200+ newcastle.
For some reason, my Core Center started reporting temps in Fahrenheit instead of Celcius. Degrees F is good if I want to know the weather, but I'm much more familiar with C when it comes to computer temps. How would I go about changing it back to C? Plus, for whatever reason, it seemed more accurate then (after updating the BIOS) than it does now.

Yeah...acts like a toggle switch when you right click...then pick!

Core center info

Similar Messages

Maybe you are looking for