Corecentre not reading NB temp

I have the latest version of corecentre installed on my neo2 k8n and the northbridge fan is plugged inot the correct 3 pin power socket but when i start corecentre it shows N/A for the temp and N/A for the fan speed?
any ideas why this is, i really want to be able to turn the fan down because its very loud and whiney.

All these readings are related to the same Winbond chip?
I know speedfan is able to read graphic card temperatures too.
You would disconnect the fans connectors one by one and check the readings to identify the info but it is a few risky because you will need doing this with the system up and running.
I woudl bet System in Core Center is related to the chipset. NOrmally the hotest temperature corresponds to the CPU, the middle to the chipset and the third the case.
Common idle temperatures are
43~45 --> CPU
30~35 --> Chipset
Test the temperatures at full load, the temperatrures with faster increment will correspond to CPU / Chipset.

Similar Messages

  • Z97 Gaming 7 Not Reading CPU Temps

    I have had the Z97 Gaming 7 installed since July/2014 and had no issues. Today when I booted up I noticed that the debug LED was not displaying the CPU temp just "00". In the bios it also does not display the CPU temp but the system temp is displayed. In AIDA64 the CPU temp is stuck at 40c but it shows all the single core temps correctly.
    I have removed the boards battery, cleared the CMOS and updated the BIOS to 1.80. Still showing "00" when booted up and no CPU temps in the BIOS. Can't understand whats going on here, could it be a dead sensor on the board? Some help would be appreciated.
    System Specs:
    Windows 8.1 64
    Samsung 840 Evo 1TB
    i7 4790K
    MSI Z97 Gaming 7
    Corsair Vengeance 1866 16MB
    PowerColor PCS+ R9 290
    Creative SB X-Fi Titanium HD
    NZXT Kraken X61
    Running all current drivers
     

    Thanks Nichrome. Unfortunately here where I live, that is not an easy thing to do as there are not to many IT places i would trust to have this done. I guess I'll have to look around to see if I can borrow a Z97 board or a Haswell Processor to rule out with component needs to be RMA'd.
    If any one else can add any more insight I would be grateful.

  • Adobe Media Encoder for CS4 error Could not read from the source

    Hello,
    I get an error when I try to export from Premiere CS4. It doesn't matter how I export. Seems like an easy fix, but I can't figure it out. Any help is appreciated:
    - Source File: C:\DOCUME~1\ARTWHI~1\LOCALS~1\Temp\extra and b roll.prproj
    - Output File: E:\Living Accused Movie Transfers\video\Cindy at table.avi
    - Preset Used: NTSC DV
    - Video:
    - Audio:
    - Bitrate:
    - Encoding Time: 16:10:34
    1/21/2009 9:50:25 PM : Encoding Failed
    Could not read from the source. Please check if it has moved or been
    deleted.
    Thank you
    Art

    When you attempt to encode media with Adobe Media Encoder CS4 on Windows, the following error message appears in the text file (AMEEncodingErrorLog.txt) that opens when you click the error icon: "Encoding Failed. Could not read from the source. Please check if it has moved or been deleted."
    If it's that correct, you removed an earlier version of Adobe Premiere Pro or Adobe Creative Suite on the same computer.
    Do one or both of the following solutions:
    Solution 1: Create a shortcut to the Premiere Pro executable file, rename the shortcut to Premiere, and move the shortcut to C:\Program Files\Common Files\Adobe\dynamiclink.
    Close all Adobe applications.
    In Windows Explorer, navigate to C:\Program Files\Adobe\Adobe Premiere Pro CS4. (If you installed Premiere Pro CS4 in a location other than the default of C:\Program Files\Adobe, then navigate to your custom installation location.)
    Right-click on Adobe Premiere Pro.exe (which might appear without the .exe extension) and choose Create Shortcut.
    Rename the newly created shortcut to just Premiere.
    Important: The name of the shortcut must be exactly Premiere with no other characters.
    Open a second Windows Explorer window, and navigate to C:\Program Files\Common Files\Adobe\dynamiclink.
    Move the Premiere shortcut that you created into the dynamiclink folder.
    Solution 2: Remove and reinstall all Premiere Pro CS4 components or all Adobe Creative Suite 4 components.
    Do one of the following:
    Windows XP: Choose Start > Control Panel > Add or Remove Programs.
    Windows Vista: Choose Start > Control Panel > Programs and Features.
    In the list of installed programs, select Adobe Premiere Pro CS4, Adobe Creative Suite 4 Production Premium, or Adobe Creative Suite 4 Master Collection.
    Click Change/Remove (Windows XP) or Uninstall (Windows Vista).
    Follow the on-screen instructions to remove all components of Premiere Pro CS4 (including Adobe Encore CS4 and Adobe OnLocation CS4) or to remove all components of your edition of Adobe Creative Suite 4.
    Re-install your Adobe software.

  • File Import error: Could not read from source (OS X 10.8.2)

    I am having this time-wasting problem on a new Creative Cloud CS6 installation. I queue my Premiere exports normally on AME (CS6 updated versions), and they work fine if I start them right away. If the Mac is restarted however, they will fail giving this error. The log shows "Could not read from the source. Please check if it has moved or been deleted". It looks for the source file at /Users/Username/Library/Caches/Temporary/projectname.prproj. Isn't AME supposed to hold the queue even after a shutdown/restart? Premiere has been uninstalled and reinstalled once, so maybe that's the cause of it? Thanks.

    Unfortunately, it looks like you've found a bug, an unplanned interaction between Premiere Pro's choice of temp directory and automatic OS behaviors.
    Jeff is correct, AME will hold the Queue between reboots. The problem is with the temporary project that Premiere creates.
    When you queue a sequence to AME from within Premiere (File > Export > Media, click the Queue button), Premiere creates a copy of the project in that temp directory. That is the file reference it sends to AME.
    The problem is that Mac OS appears to flush that directory on reboot. Thus, when you reopen AME, it can't find the file anymore.
    The bug is therefore that Premiere Pro is putting the file in a place where it can be deleted before being used. Sorry about that. I'll file the bug.
    You can work around the problem using a different method to add your sequence to the AME queue. Inside AME, use the File > Add command. You can also drag and drop the sequence icon from the Project panel in Premiere to the Queue panel in AME. Or you can just not reboot until you've rendered what's in the queue.
    I suppose it's possible that you could make Mac OS not flush the temp directory on reboot. There's a lot of fun things you can do in Terminal if you know the right commands. That's beyond my personal skillset.

  • Encore CS4 error "could not read from the source file"

    - Source File: C:\Users\Anil\AppData\Local\Temp\2013 11 08 c Big Budha_9.prproj
    - Output File: F:\Adobe Encoded Blu-ray\For Disk #013\Disk#013-B\2013 11 08 c Big Budha.m2v
    - Preset Used: Full HD 1080i [MPEG] 30 MBPS
    - Video:
    - Audio:
    - Bitrate:
    - Encoding Time: 01:49:53
    25-Jan-14 2:50:32 PM : Encoding Failed
    Could not read from the source. Please check if it has moved or been deleted.
    i have tried creaeted a NEW Premiere Pro project and still get the same error again ... can someone help me to figure out what is wrong ...

    Hi Neil
    I have been using file names with spaces and it has been working fine. As stated in reply to Jones, uninstall and reinstall of Premiere Pro CS4 has helped to get rid of this error.
    also i did not use Dynamic link, but was trying to create MPEG file using Media Encoder and then import it in Encore.
    your suggestion for H264 seems good and will try it.
    x264 Pro is for CS5 and above versions, so it seems i can not use it and have to manage with Adobe Media Encoder's default. Hope i will not have any major technical issues.
    please suggest me for below:-
    1) i have 4 hours of Full HD footage and made 1080i MPEG2 files of 30mbps to fit in 2 seperate Bluray Disks.
    2) now i plan to put all in one Single Bluray Disk by reducing MPEG2 file average data rate to 15mbps. will that work or is there any limitation of time in Bluray Disk.
    3) Will it be ok to create H264 files at 30mbps [as you mentioned H264 reduces file size to half of MPEG] and still be able to fit 4 hours footage in one BR Disk ?
    4) even though i specify Min 10 Target 25 Max 30 data rate for MPEG files creation, it creats file at data rate of 30 mbps, can you explain why it is happening as i thought my target rate should be 25 mbps and not the maximum rate specified.
    Thanks ...
    PS...
    my source file is .mov 1920 x 1080i 29.97 fps from Canon 6D. first i tried to create progressive file in Encoder but while imported in Encore realised at 29.97 fps, it allows only interlaced file and had to transcode back to interlaced. so i stick to interlaced file.
    Canon 6D also allows me to shoot in 24fps [motion movie] which Encore can handle as progressive file for authoring. What are the pro and cons of shooting in 24fps, if you can suggest.
    Message was edited by: AnilHVarma

  • What is the matter with business catalyst? It is supposed to be so easy I can not upload a temp site or get any answer  why

    Is something wrong with BC I can not preview my temp 30 day site I get a Coming Soon sign and no preview of my site. I have contacted support they say it is resolved but it is not. This is supposed to be easy. This is my final project for class to publish my portfolio it would be nice to hand it in on time. I got real excited about MUSE but publishing on it is a real downer for me.

    Thanks - I had same problem with newly-imported Bookmarks from IE which didn't show in the sidebar. I have opened the Bookmarks Menu and all is OK.

  • When I was talking on phone, suddenly the phone was switched off. i tried to switch it on but it gave the message....connect to itunes for set up.  when I connected it to itunes...it gave the message, itunes can not read data from this iphone, restore it

    when I was talking on phone, suddenly the phone was switched off.
    i tried to switch it on but it gave the message....connect to itunes for set up.
    when I connected it to itunes...it gave the message, itunes can not read data from this iphone, restore it to factory settings. It also said while restoring ypu will lose all media data but you can restore the contacts.
    I restored the factory settings....the phone was on recovery mode...it was verified by itunes and all that..but in the end it again said that iphone has some problem and can not function right now.
    after that when ever i connect it with itunes, it gives the message, it can not activate the iphone further, try again later or contact customer service.
    What to do now?????? Customer service people say..it is hardware problem

    If it's a hardware problem, then the phone will need to be replaced.
    There is no magic that can fix a hardware problem.

  • VSTS loadtest error while running Loadtest with Runsettings as No of test iterations , ERROR is : could not read result repository: unknown transaction id in results:

    Subject: VSTS loadtest error while running Loadtest with Runsettings as  No of test iterations ,  ERROR is :  could not read result repository: unknown transaction
    id in results:
    Hello All,
    I am facing the following error while running a loadtest (when i choose the scenario to be executed for No of test iterations). But the same loadtest with the Run duration for X minutes is running fine without any issues. 
    Any suggestions on the issue i am facing
    error is :
    could not read result repository: unknown transaction id in results:
    or
    could not read result repository: unknown request id in results: 
    Thanks
    Satish

    Hi Kotapati,
    >>Subject: VSTS loadtest error while running Loadtest with Runsettings as  No of test iterations ,  ERROR is :  could not read result repository: unknown transaction
    id in results:
    According to your description, you mean that when you run your load test using the Test Iterations way and then get the error message, am I right?
    If yes, please you try to close the VS, and then open this VS again. Then clean your load test project/solution and then re-build it, run your load test again check this issue again.
    In addition, I suggest you could try to create a new load test and then run it using Test Iterations way check if you get the issue for the specified load test or all load tests.
    If possible, I suggest you could share me simple load test for us so that we will further help you.
    You could upload your load test to OneDrive and then copy link here.
    Best Regards,
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • I am trying to import cr2files from the camera into lightroom 5 and keep getting an error message saying Lightroom can not read the files and therefore will not import them.  Has anyone had a similar problem-.thanks

    I am trying to import cr2files from the camera into lightroom 5 and keep getting an error message saying Lightroom can not read the files and therefore will not import them.  Has anyone had a similar problem….thanks

    If you are having the same problem, i.e. a disk permission problem, open your favorite search engine and search on, "change disk permissions", and I think you'll find plenty of information on how to fix the problem. This is a Lightroom forum. Your problem is with your operating system. There is no sense in rewriting instructions that are already available if you do a simple search.

  • I have a brandnew 7th gen classic ipad, it does not read in my itunes anymore. i bought it cause apple was suppose to be good, now i am lost as i just want my music, any help. tried the rec. steps to fix it and nothing

    let em elaborate more, the unit is less than 5months old, i bought it just for music, i use to have a lot of cds, well it does not read anynore in my computer nor the itunes programe, i reset it, i put it to disk mode, i down loaded the newest itunes program, i want to know how to fix this as i paid apple good money for a product that died after 5months, for real.
    this is bad business and i need some help

    Does the iPod work okay otherwise apart from not being able to connect with and communicate with iTunes?
    Have you tried connecting the iPod to another PC or Mac running iTunes to see if it is properly recognized there?
    Is iTunes up to date on your PC?  Does it appear in Device Manager when you plug it in? To access Device Manager, click start, right->click on Computer (or My Computer in Windows XP) and choose Manage.  When the window opens, select Device Manager in the left hand pane if necessary.
    Any unknown devices listed or does the iPod appear anywhere under USB Host Controllers?
    B-rock

  • My PC is not reading my itunes music files, all I get is '!'

    Hi, my computer recently crashed and I had to recovery the HDD and lose all my materials, but I still had all my itunes media on a separate drive. Anyway, I redownloaded itunes and now I added a folder of over 4800 songs, all either individual mp3 files or albums in folders. Now that all the albums are up (I lost a lot of the album covers too) I am having trouble playing music on itunes.
    Whenever I click on most songs, I get a '!' saying that I have to now search for the file because it cannot be found. I have to search for EVERY song before it can find it. I have over 4800 songs, so I can't realistically search for EVERY ONE. Under 'Preferences' I went into "Advanced" and chose the folder where my songs would be read from. Yet still I have this problem. Funny thing is that it doesn't do it for EVERY song, but I would say about 90% of them. Why is my itunes not reading my files? I have the latest version of itunes on my PC and there is no problem with any of my mp3 files as they are all well and play fine on my ipod. The strange thing here is that all of my movies play just fine, I have 34 digital copy movies on my itunes. I have Windows 7.
    Please help, this is a really annoying thing to deal with!

    Since you mention PC, I'm guessing that you are referring to a Windows machine. If so, then see this support document.  http://support.apple.com/kb/TS1538

  • Problem:  this mac is not reading an excell file after upgrading to yosemite.   My Mac is from 2009, it use to work perfectly but it wasn´t able to open some apps, thats why i upgrade it.   Now it once i donwload the zip it appears with an ".ods" ext

    Problem:  this mac is not reading an excell file after upgrading to yosemite.   My Mac is from 2009, it use to work perfectly but it wasn´t able to open some apps, thats why i upgrade it.   Now it once i donwload the zip it appears with an ".ods" extension
    i even already download a link
    http://www.microsoft.com/en-us/download/confirmation.aspx?id=44026
    which i read on another support page... but it doesnt allowed me to install it cause it says that i already have the disk of this program....
    Im afraid to erase it and not being able to get it back...
    What can i do!??
    Thanks in advance for this kind answer!!!

    fsolution wrote:
    Problem:  this mac is not reading an excell file after upgrading to yosemite...   Now it once i donwload the zip it appears with an ".ods" extension...
    If the "it" refers to a compressed (zipped) spreadsheet that you downloaded, the ".ods" extension is used by LibreOffice and probably OpenOffice (which are free versions of MS Office) for spreadsheets, which would suggest that wherever you're getting that "Excel" file from has switched to one of those programs. I've tried opening an .ods file from LibreOffice using MS Office 2013 for Windows and it does open though with a warning that some things have been changed. I don't know if Office for Mac can normally open .ods files. But if your need is to just open .ods files, take a look at LibreOffice.

  • MacBook Pro (Retina, 15-inch, Mid 2014) will not read an SD card in the SDXC card reader. Does anyone know whats going on?

    MacBook Pro (Retina, 15-inch, Mid 2014) will not read an SD card in the SDXC card reader. Does anyone know whats going on?

    Hi David.  I don't have as modern a Macbook Pro as you, mine is a 2012 model, but perhaps I can help.  I often find that my SD card will not load when I first insert it.  I have to remove it and then put it into the slot again firmly.
    You also haven't posted any information about the SD card.  What size is it, do you know how it is formatted, has it worked in that same mac previously, where did it come from, does it currently work in another device (such as your camera)?  This sort of information will help to narrow down the problem.
    If you post some more information I'm sure people will try to help you.  In the meantime, if you look at your post again you should see "More Like This" at the bottom of the page and you may find an answer in some of those related posts.
    Hope that helps.
    Ivan

  • TS3694 My computerwill not read the lastest version of i tunes. i lost theold version how do i get it back to hold my music again???????help

    My computer will not read the lastest version of i tunes ,i don;t know how to get the old version b. pleae help. i can't get my music back on my computer

    what do you mean it will not "read" the latest version? you downloaded, installed, and nothing? it doesnt open?
    does your computer meet the minimum requirements for itunes 11?

  • LR 5.6 on Mac desktop all of a sudden will not read any card from any reader but will work on my laptop. I can work on previous images but not import new ones. Even if I create a catalog on laptop and import to my desktop on a thumb drive, the images are

    LR 5.6 on Mac desktop all of a sudden will not read any card from any reader but will work on my laptop. I can work on previous images but not import new ones. Even if I create a catalog on laptop and import to my desktop on a thumb drive, the images are only accessible as long as the thumb drive is inserted.

    Sounds like you may need to repair the Disk Permissions on your drive where your images are stored.

Maybe you are looking for