Correct CPU temp? Give your room temps Please

Loads of questions abound on correct CPU temps, yet very few give their room temps, which can greatly affect CPU temp. CPU temps will usually vary in some direct proportion to your room temps. You'll get a faster, more accurate answer if you include them. (Of course, you'll also want to specify if your temps are generated by just idling or under the load of higher powered apps such as games.)
It's also helpful to know your location; eg Alaska or Carribean island (edit your profile to include) as different locations present different cooling challenges. As well, it's easier to recomend gear suppliers if we know generally where you are.
Cooler days!

The short answer is that cnq will not affect your load temps, since when loaded, it is effectively running exactly as it would without CNQ.
Yes, the temp will "shoot up" more when you go from non-loaded to loaded with CNQ, simply because it is starting from a lower temp to begin with.
You will learn not to trust corecenter readings eventually - they are by no means guaranteed accurate.
If you put your finger on your cpu heatsink when under load - if it's fairly warm, that's ok - if you can't hold it there for 10 seconds without burning, it's too hot.
Edit: I see you were using speedfan - same comment about accuracy applies.

Similar Messages

Correct CPU temp for a P4 3.06 with & w/out water cooling

What is the correct CPU temp for a P4 3.06?
and also what should the temp show for a P4 3.06 running
an Innovatek Water Cooling System
Many thanks,
Acinom

Thanks for all the great info!!
I am running idle (cpu) at btw 44c and 46c. When I installed a game (quake) and then played it my temp rose to 52c. So I guess I am ok right now. I would like it to run a little cooler however.
I am running Innovatek -
CPU block
Northbridge Block
Video Card water block
2 HD blocks
Innovatek Konvekt -O-Matic passive water cooling heat dissipation: over 4 pounds and 13 1/2 inches long by 9 inches high
Also I am using the NEW Nanotherm PCM+ on all blocks (cpu, gpu, northbridge)
All the blocks are smooth, no leaks. I am using an Eheim 2011 pump which also holds over 1000ml reservoir AND I have a tank-o-matic 280ml reservoir. I am using distilled water with the Innovatek conditioner (2 bottles equaling about 30% ratio). I have two fans in the system.
The only temp I can gauge is my CPU. I do not know how to check my GPU or Northbridge temps although I would like to know how, please. My ambient room temperature is around 72 to 74 degrees.
http://home.houston.rr.com/acinom/

How to reduce from 5º to 8ºC CPU Temp on your MSI K7N2 Delta!

I've installed this tweak last week and it is working very stable since then. It decreased my Idle CPU Temp from 42º to 36º and Overload from 54º to 48º:
Just go: http://forums.pcper.com/showindex.php?t=280137
AMD ATHLON XP 2600+ 12.5x333mhz 1.65V ~OC 11.5x400mhz 1.55V
Thermaltake Volcano 9
MSI K7N2 Delta L
MSI GF4 4200-8X graphics Card
160GB Maxtor HDD 7200rpm
768MB Samsung DDR3200
LG 48x24x48x/16x CDROM/DVD Reader
Dual Fan 450W Troni Power Suppy

It seems that the link to the tweak is broken, I've found another one:
http://ftp://ftp.vector.co.jp/pack/win95/hardware/other/wpcre14.exe
This is what the article say:
Just tried it for the first time..It works GREAT
My idle temps are now 26c, down from 34c. That's 8C. I can have Winamp, IE and messenger running and CPU temps don't get by 29c. Once i fire up, SETI though...I get back my regular Load temps at 39c.
Some of you probably know about it, already....here's for thousand others that don't.
This tweak can drop your idle CPU temps down as much as 8c, maybe more...depending on your system.
First thing you need to do is download WPCRSET & WPCREDIT.
They're both in this zip.
- Extract to a directory.
- Run "INSTDD.EXE". Click Install. When done, you will be prompted for restart. Hit Yes! -
- Then go back to the folder with extracted files, and open "WPCREDIT.EXE"
- A ms-dos like window will pop-up. Move the blinking block (with arrow keys or your mouse pointer) until it says Offset 6F at the buttom. Now, click on the two digit number where it says "HEX", and change it to 1F (The Hex for Offset 6F would have previously been 9F, 8F or something else). Hit Set.
Your idle temps should now start falling.
You would have to do this hack/tweak everytime you rebooted your computer if it wasn't for WPCRSET.
- Go to directory and run "WPCRSET.EXE"
- Look at the top of the window: Enable select "Start" and make sure Device is on "enable"
- Then click Add. Enter 6F for the register, and 1F for the data
- Click Ok and you'll be prompted to restart.
Once, you rebooted, open WCREDIT again and see if the 6F register is still on 1F. If it is, then that's it..You're all done.
Here's a Screenie of how it should be:
This only brings your idle temps down, and not your full load temps
It should work for all nforce2s, and use at your own risk
Check your nf7-s for CPU Disconnect. Most other nforce2 motherboards do not have this feature in the bios...so this tweak might prove useful.
READ THE WHOLE THREAD BEFORE TRYING THIS!
If you run a Distributed Computing project...then obviously this would be of no use to you
Quote:
Originally posted by Abducted on 12-16-2003 at 03:43 PM
It activates the C1 (and maybe the C2) function Athlon XP CPU's support. Most mainboard brands have this feature as an option in the bios you can enable and disable. I just found out that EPoX doesn't have that feature. So what you're doing is just using a direct reg tweak to activate it. It's not like you're forcing anything, the Athlon XP chips are made to support this feature so it shouldn't do any damage.
When the CPU is idle the mainboard will send a command to the CPU that will cause a part of the CPU to be deactivated (and therefore not produce any heat). That's why this tweak only works on the idle temp and doesn't change anything on the load temp. Ofcourse as soon as the CPU power is needed the deactivated part will become active again, so it should have any influence on the performance of the CPU.
Strangely, my full load temp has decreased 6º C degrees too.

What are some of your system temps?

Hey all.
Out of curiosity, I was wondering if you all could post your System temps and your CPU temps. I am running Folding @Home now 24/7 and I just want to compare some of yours with mine to make sure I am doing ok.
I just got a new case and installed an 80mm exhaust fan in the top center, another 80mm exhaust towards the top on the back of the case, a 120mm intake in the front panel, and have another 80mm intake in the center of the side panel.
Before I was Folding the idle temp for CPU was 109F. 42C.
Idle SYSTEM temp was 98F. 36C.
Now that I am Folding the CPU is always at full load so now my temps are always around 112F. 44C. for my SYSTEM and 125F. 51C. for the CPU.
BTW, this is with the FSB set to 143, 1.85V for CPU, and 2.7 V for Memory. The ambiant temp in the room varies between 68F. 20C. and 72F. 22C.
My main concern is when summer hits and the ambient temps go up to about 80F 26C.
Thanks.

Quote
Originally posted by jonnyturner
im idlin @ 32 (CPU) and 36 under load
god bless my thermaltake volcano 9....shame im now deaf!
I get the exact same TEMP with my volcano 9 but im not deaf.... lower the RPM to about 3500 with the pot. You dont need to run it at full blast, its way too loud. Just have a good air flow in the case and have it set to 3500 RPM.

How to trigger email notification when users fail to give correct answers to reset your password in fim 2010 r2

Hi,
How to trigger email notification when users fail to give correct answers to reset your password in fim 2010 r2
Senario:I want put wrong answering to the Questions that i was during registration if i give wrong answers to the questions then a Email Notification should be trigger to Users.
Regards
Anil Kumar

Hi Sylvain,
I did all thing as you told me.First i created Criteria based Set after this we created a Workflow type Action and Actvities Type Notifcation Email template and finally i called this Workflow in MPR as Set Transition and call Set that i was created below.and
check Advance View of Set this gives
<Filter xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema" Dialect="http://schemas.microsoft.com/2006/11/XPathFilterDialect"
xmlns="/Request[(Creator">http://schemas.xmlsoap.org/ws/2004/09/enumeration">/Request[(Creator = 'b0b36673-d43b-4cfa-a7a2-aff14fd90522') and (RequestStatus = 'Denied or PostProcessingError')]</Filter>
But this is not working for me so please tell me where i am wrong.
Regards
Anil Kumar

Help me Please.. I can log on to the Apple website to manage my account and all the information is correct, but I get "Your Apple ID has been disabled" when I try to get something from App Store on my iPad

Help me Please.. I can log on to the Apple website to manage my account and all the information is correct, but I get “Your Apple ID has been disabled” when I try to get something from App Store on my iPad3
I'm from poland.
Thx
Balbi

Contact iTunes Customer Service and request assistance...
Use this Link > Apple Support iTunes Store Contact

When I try to start my macbook it gives an error of Please restart your computer, but when i do this i get the same error.

When I try to start my macbook it gives an error of Please restart your computer, but when i do this i get the same error. This occured after my macbook pro shut down (because of low battery) while it was installing some updates. Please Help?

Try reinstalling OS X. What version did you have installed? If it's Snow Leopard do this:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.

What is the error code mean? And how to solve it ?Please give your answer. Thanks

What is the error code mean? And how to solve it ？Please give your answer. Thanks
Attachments:
QQ截图20140403134626.png ‏59 KB

duplicate post
LabVIEW Champion . Do more with less code and in less time .

Quickly!Quickly!Quickly!What is the error code mean? And how to solve it ?Please give your answer. Thanks

What is the error code mean? Why is there an error?And how to solve it ？Please give your answer. Thanks！
——1110340026
Attachments:
QQ图片20140403140655.jpg ‏108 KB

Sannieboyyyy wrote:
Could be me, but your VI is not working properly on the english version of LV. Can I suggest you to try programming in English in the future?
Yes, it's you. The VI is working just fine, except for some cosmetic issues with the labeling. I don't think is is a valid suggestion to force somebody to program in a specific language, especially since LabVIEW supports all these languages.
Here are the problems with the VI:
If you don't want an amplitude of zero, you need to set the amplitude control to a nonzero value before running. Simple as that!. (You could also set the input range for the amplitude control to exclude zero or use a case structure to skip certain code if the amplitude is zero).
You could also wire the error output to an indicator so it simply displays the errors, but keeps running.
Your while loop is currently useless. You can delete it and the program function will not change. Use a stop button at the loop condition.
Your while loop needs some timing so it runs at a reasonable rate. Either add a small wait or configure the signal generation to "simulate acquisition timing" instead of "run as fast as possible".
LabVIEW Champion . Do more with less code and in less time .

Increase the DB size in Azure gives the Error " Msg 40197, Level 16, State 1, Line 1 The service has encountered an error processing your request. Please try again. Error code 40671."

Increase the DB size in Azure gives the following error
Msg 40197, Level 16, State 1, Line 1 The service has encountered an error processing your request. Please try again. Error code 40671.
i have used following ALTER query,
ALTER DATABASE database_name MODIFY (EDITION='Business', MAXSIZE=10GB);
Regards
Vel

Hi Taiye,
According to your description, in theory, we can modify the size of database, and the T-SQL statement in your post is right. So we need to verify if there is no problem with network when you execute the modification statement, in addition, you must be connected
to the master database when executing the ALTER DATABASE statement. As the error message, I recommend you login again and connect to the master database then run the statement again.
For more information, see: ALTER DATABASE (Windows Azure SQL Database)
If the error is still exist, the Microsoft support engineer will help to solve the problem from backend. Sometime delay might be expected. Your patience is greatly appreciated.
Thanks,
Sofiya Li
If you have any feedback on our support, please click here.
Sofiya Li
TechNet Community Support

It gives message that "Java Script Disabled on your browser. Please Enable it." but it is allready enabled what should i do

While browsing "http://edudel.nic.in" this site when we enter id and password it gives message"Java Script Disabled on your browser. Please Enable it." but it is allready enabled in Tools-> Options-> Content window

The problem is there's a glitch in the javascript of http://edudel.nic.in/mis/MisAdmin/frmMisLogin.aspx
There's a form element with an ID of "txtpassword", but in their validation function, they call it with getElementById("txtPassword"). Obviously a case issue, but it apparently works in IE.
I created a workaround for a user I met in #firefox, a simple greasemonkey script that replaces the function with a fixed version.
Here's the link:
http://userscripts.org/scripts/show/102156

"Currently unable to add funds to your account. Please try again later."

ultimatedeterus wrote:
I tried to add funds to my PSN account with my debit card. but seems like it did not work.it showed "Currently unable to add funds to your account. Please try again later."and also i found there's $1 pending transaction on my bank account. WTH is going on?how can i fix this problem?and I'm pretty sure the billing info on my PSN account is EXACTLY as same as the one on me bank statment.The transaction pending is the way that PSN validates your account. It attempts to withdraw, then deposit £1 or $1 then refund it. If you are unable to do it yourself on the PS3, try waiting 24 hours as you may have inadvertantly triggered the lockout. (several attempts that fail will lock it for 24 hours). If after waiting it still doesn't work, give customer support a call and see if they can help. The EU numbers are available here.

r3KoR_Infinity wrote:
Hello,
I have the same problem. It just recently occured though. I used my old debit card with no problem at all and purchased a bunch of games in the Playstation Store, however I lost my DC a week ago and got a new one. Obviously I changed my billing information and that's when the problem started.
1) I see a small pending transaction to Playstation Network which proves that my data that I put in was correct.
2) Called the bank which confirmed that I have enough funds for the purchase and also confirmed that my card is active.
3) Tried to buy a game in Google's Playstore for my phone, which also refers to that same DC number and had no problems.
4) Contacted PSN/SEN customer support and got no response.
I would buy PSN cards if I could but since I am currently living in Thailand i need to say that it is really hard to find one. I am not even sure if there are PSN cards for the Thai region, since if I do see some they are for the US region. Thus I am really dependent on my DC purchases.
Any way of solving this?
The billing address for your card must match the residential address on your PSN account for the transaction to complete.
Are they both registered to the same address?

Error processing your request Error We're sorry, we encountered an error processing your request. Please try your request again. You may wish to try one of the following links:

Cannot download trial version of Livecycle Designer:
I select English windows then click download. It then takes me to this page.
Error We're sorry, we encountered an error processing your request. Please try your request again. You may wish to try one of the following links:
What gives?????

I get this same error message when I try to download it, but I have purchased the full version and have a license key. I get this error screen when I try to download it from both Safari and Chrome on a Mac running OSX. A screenshot is attached.

Adding Picasa account: Android error - There was an error creating your account. Please try again.

I successfully synced with gmail (contacts, mail, etc.), youtube, as well as some other services. I am unable to create the account that accesses Picasa. Each time I try, I enter the email and userid for my account, and I get the same error message "There was an error creating your account. Please try again". I verified that the username and password are correct by signing into Picasa Web directly. A number of other people are experiencing this problem, as can be seen here: http://www.google.com/support/forum/p/Picasa/thread?fid=446b5bd3493325ff0004ad7d643c968c&hl=en
Does anyone know what to do to make this linkage work? I want to be able to use the integrated gallery to access my Picasa pictures.

Oracle forums: current quality level...

ERROR: The Windows Installer Service could not be accessed. This can occur if the Windows Installer is not correctly installed. Contact your support personnel for assistance.

Hello Everyone,
I keep getting this when trying to install 0r repair SQL Server 2008 R2 on a SBS 2011 Standard.
TITLE: Microsoft SQL Server 2008 R2 Setup
The following error has occurred:
The Windows Installer Service could not be accessed. This can occur if the Windows Installer is not correctly installed. Contact your support personnel for assistance.
For help, click: http://go.microsoft.com/fwlink?LinkID=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.50.1600.1&EvtType=0xDF039760%25401201%25401
BUTTONS:
OK
the provided link says "There is no additional information about this issue" i am helpless
please tell assist.
Thanks.
Abdallah.M.M

Hi Abdallah,
According to your description, could you please post the summary and detail logs for further analysis? By default, the logs can be found in: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log.
Usually, the error occurs when the Windows Installer Service is not running or the Windows Installer registry settings are corrupted. I recommend you reset the Windows Installer Service settings in the registry and restart the Windows Installer Service,
then reinstall SQL Server 2008 R2. For more details, please review this similar
article.
Thanks,
Lydia Zhang

Correct CPU temp? Give your room temps Please

Similar Messages

Maybe you are looking for