Corsair Value Select on MSI K8N NEO Platinum Edition

Does anyone have this combo? (A64 CG) and can tell me some clock result and bios etc how high fsb and so on
THX
/Stiga

value ram usually will not clock high, higher end ram like corsairs xms is better suited for ocing

Similar Messages

MSI K8N NEO Platinum Edition memory question

Hi there,
I've currently got a MSI K8N NEO Platinum Edition (Nforce 3) motherboard and 2X 512 MB Corsair Value Select memory modules (both double sided) running at DDR 400 - this runs completely stable and has done for a number of months. I would like to increase my memory to 1.5 Gig but there seems to be a lot of issues?
I originally planned to buy an additional 512 Meg Corsair value select chip and place it in Bank 3 - is this acceptable?
I assue that i would have to drop the speed down to DDR 333 from 400, could anyone tell me how much of a difference this actually makes (when playing FPS games Doom3 etc..) ?
Any help would be greatly appreciated as i've been looking through both this forum and the Corsair one and i cant seem to find the answer.
thanks in advance !

Just note that there are combinations of two sticks that will also make the board run in DDR333 mode (see page 2-8 of the manual). For example, using two double-sided sticks in DIMM2 and DIMM3. I've actually managed to get it to work at DDR400 in those two slots, but it's not perfectly stable and overclocking diminishes drastically. Bottom line is the system will work fine when forced to DDR333...as long as you don't expect to overclock the RAM to any significant degree.

MSI K8N NEO Platinum Edition PROBLEM

Hi (my english is not good sorry for that)
I just got my new computer:
MSI K8N NEO Platinum Edition
AMD Athlon64 3200+
Western Digital Caviar 160Gb
PNY Verto GeForce 6800Ultra 256Mb
1GB Value Select pc3200
Levicom 500W
The Problem is that when i start the computer, it boot and die directly no bootscreen what so ever, it boot and die. i dont know what to do plz help me

Make sure you have Both the ATX Wires on.. theres the Big one! (21Pins i think).. and the Small 4Pin Connector both need to be connected.. if you havent done so yet.. Another thing you could do is Take everything out and place it on a cardboard or something appropriate for the mobo.... I think your motherboard is shorting?.. if it's touching your case.. I had somewhat the same issue long time ago.. give it a try..if you want hope it helps..

MSI K8N NEO Platinum Edition Low Benchmark scores

Hi, can someone please help?
I have these details of my friends new PC :
MSI K8N NEO Platinum Edition
AMD Athlon 64 3200+ 2.2 GHz Socket 754, 512 KB cache
Corsair Value S. PC3200 DDR-DIMM 512MB
I have run a sandra memory bandwidth test on it and I think he gets really low scores for his spec.
int buff'd 2657
float buff'd 2656
This is the scores he gets un tweaked and not overclocked. Do these sound like reasonable out of the box scores??
Any information would be appreciated

Quote
Originally posted by tritium4ever
Who cares, Sandra is a completely synthetic benchmark with absolutely no relevance to real world performance. Don't believe me? Put a 3.0C up against a 3000+ S754 with the memory bandwidth benchmark. The 3.0C will own, but the 3000+ will perform better in most real world apps. Bottom line: don't sweat the Sandra results.
not 100% true either beacuse if you then run encoding apps etc which are mem bandwidth dependant the 3C would own. it is not true to say they are not real world results, just games and most apps dont bottleneck on the mem bandwidth.....now that is will be different on 64-bit coding but of course the A64 would still own the 3C on them.
just for the record i would never buy an intel.

MSI K8N Neo Platinum Edition review

MSI K8N Neo Platinum Edition
http://www.tbreak.com/reviews/article.php?id=290

Is it worth the money I wonder? There aren't that many programs written wich can run in 64 bit mode! This is truly the main reason for getting this board unless all you guys have a load of money and want to be at the cutting edge.
I think I'll wait till its get worth the money... or am I completely wrong here?
E-Dog

MSI K8N NEO Platinum Edition Memory plz help!

Hi
http://www.datorbutiken.com/se/defa...2X512DDRCA400PR
Is this memory ok with MSI K8N NEO Platinum Edition ?
If it is, do you know how well its oc:s?

He would be talking about this:
http://www.newegg.com/app/viewProductDesc.asp?description=20-145-466&depa=0
But I wouldn't reccomend that memory mainly because I have heard mixed reviews about it. You can get the same (if not better) memory at either of these links, the only difference between the two links is the color of the heatspreader (as far as i can tell). This is the memory I have and it works very well, plus its much cheaper:
http://www.newegg.com/app/ViewProductDesc.asp?description=20-145-449&depa=0
http://www.newegg.com/app/ViewProductDesc.asp?description=20-145-450&depa=0

Any MSI K8N NEO Platinum Edition S754 nForce3 users?? Need advice..

Hi, thinking of building a budget system around a S739 Clawhammer 3700 with an
MSI K8N NEO Platinum Edition S754 nForce3 board. But have a few concerns..
- Will this board run on this chip or will it need updated BIOS to do so?
- Will it work with crucial 3200DDR memory.CL=3 • UNBUFFERED • NON-ECC • DDR400 • 2.6V • 64Meg x 64 ?
- Can it take an extra (3rd) 512 stick of this ram?
Thanks.

I have ran the Neo s754 model with 2 * crucial CT6464Z40B 512MB cas 3 modules and never had one single problem with the combination
of A64 GC version , mobo and RAM .
Three modules is tough on the single channel memory controller though , as it would have to deal with 6 banks
and you probably see the ram max speed as DDR333 and 2T commandrate is what it can cope with.

MSI K8N Neo Platinum Edition vs. ASUS K8N-E Deluxe

I'm beginning to get nervous. Since almost everyone has had problems with the MSI board, I'm beginning to doubt it's a good choice...
I've been looking some at the ASUS K8N-E Deluxe. Is this board a better choice?

Quote
Originally posted by beheader
Quote
Originally posted by Richdog
Quote
Originally posted by beheader
Quote
Originally posted by Richdog
It could be an amazing board if it didn't behave like the DFI Ultra B did... with it's cold-boot problems when OC'd, need of using a BETA BIOS for good overclocking results, losing the PS/2 mouse on boot-up. A couple of my friends can't break 230Mhz HTT no matter what BIOS they use, and their components are all good for it. I can safely say that this is my first and last MSI product. When I also compare the MSI support forums to those of ABIT etc I also find them sorely lacking. It's not the most constructive or knowldgeable place in the world. I'll be getting the DFI NF3 when it's released I think, even if it does have the cold-boot problems it can't be worse than the MSI, and will likely at least come with an active chipset cooler. As for reliability, two of my friends build computers for a living and swear by ASUS and ABIT, they would never build MSI into their systems. MSI is very much a mid-rank manufacturer, not top-flight.
*dons flame-suit*.
I don't think anyone is going to flame you... but I will point this out:
You are over clocking. ? You'll get varied results from any brand.
Like there's some inherent warranty behind overclockability. Give me a break.
I had an ASUS board where a diode EXPLODED and took out a Thunderbird. I handled it with support... like I should have.
God I hate whiners.
Listen bud, I ain't a whiner, but I say things how I see them and I don't needlessly mince my words, in my job it desn't pay to. I don't pussy-foot around anyone. Also, i've been overclocking a long while now, likely far longer then your wee self, and i've used a wide range of motherboards on both the AMD and Intel platforms.
Also, God knows what you're talking about with the "inherent warranty behind overclockability" part as that's not even in context, I made no reference to the warranty, merely on the board's performance and my opinions on MSI. They weren't offensive, merely informed opinions.
If you're going to attempt a put-down, please try and make it vaguely relevant and remotely intelligent. Otherwise...
Just for the record, my first overclocked machine was an 80286
lol same here tiresmoke, touche sir.
And SAB I hear you mate, i'm sure you love MSI motherboards, but review after review has shown they are not the best, in terms of stability or overclocking, especially overclocking in fact. Ask 9/10 reviewers and they would rate ABIT, DFI or ASUS over MSI every time. But the very fact that I bought an MSI motherboard shows I am willing to give them a chance, and I will wait until the next BIOS update for the NEO Platinum before I make my final judgement on my first ever MSI product. If the BIOS turns out to be a dud and doesn't solve the many issues with this board, i'll say bye bye forever, as many others no doubt will who have bought the MSI Neo Platinum as their first MSI motherboard, mainly because it was the first Norce3 250GB to be released.

MSI K8N-NEO-PLATINUM nForce3 250 + Corsair vs.

Hi, I'm thinking of buying a new computer with a MSI motherboard and now thinking if these will correct and have no direct problems, MSI K8N-NEO-PLATINUM nForce3 250GB + Corsair VS512MB400 Value Select 512Mb DDR PC3200 400MHz 184pin Unbuffered CL2.5. I'm not the guy who is intresserd in overclocking and such things.
Will that motherboard and memory correct good with each other ?
Sorry for my bad english. :D
//Johan
EDIT: I think I made this topic in the wrong forum. Mods move it to AMD64 nVidia Based board ?

MakubeX,
I have the Antec True Power 480. Unfortunately it only has 22 or 23 amps (the specs and the label on the psu have different ratings ) on the +12V rail. Most of the folks here recommend a power supply with at least 24 amps.
The good news is that the system in my sig is working flawlessly so the extra 1 or 2 amps don't seem to make a big difference, at least in my case. I will say, however, that according to Core Center my +12V rail runs around 11.5 volts, which is low and nearly out of ATX sepc. The low voltage will result in higher amperage draw...but again, the system is stable.
I wish you good luck

MSI K8N Neo Platinum Nforce3 250GB - PSU?

My sister in law have this board, MSI K8N Neo Platinum nforce3 250gb chipset, recently the power supply sounds noisy and a high frequency sound from the Antec Truepower 380W SP. Had maked an RMA to Antec and they had agreed to replace the 380W psu with SmartPower2.0 450W. But they asked me one question, that im not sure about:
"Make sure that your motherboard does not need the -5V. If you want more information on the power supply you can look at this link: http://www.antec.com/us/productDetails.php?ProdID=26450 "
So, do Antecs SmartPower 2.0 450W suits this board and what really is -5V for? As I read the manual, it said ATX 20 pin power connector: JWR1 and at pin 18: -5V
So does it mean this board need a psu that gives -5V on ATX 20 pin power connector and thos board can't use with Antecs SP 2.0 450W?

Quote from: syar2003 on 22-February-06, 05:10:37
Hi!
The K8N Neo Platinum (MS-7030) doesn't use -5v to anything.
So the -5v from the old atx spesification is not needed in your case.
WoW, thanks for fast reply!
So, it won't be any problem to use Antecs SmartPower 2.0 450W with this board then? Want to make sure about it, before accept Antecs offer for replacement and had spent over 4 days to find the problem with his computer. Really don't want to do it again.
This is his riggs:
Antec Sonata
AMD 64 3000+ S754
Corsair Value S. PC3200 DDR 512MB
Maxtor Diamondmax 9 250GB SATA
Maxtor Diamondmax 9 IDE 160GB
Sapphire Radeon 9550 Atlantis 128MB DDR
and
Accton ethernet card on PCI slot
MSI D-Bracket2
so
With the "new" Antec SmartPower 2.0 450W
Any problem with this rigg and PSU?
edit:
Dound this post that it said the board do need -5V and now Im confused?
http://www.archivaty.net/forums/about12964-30.html

SATA port multiplier on MSI K8N Neo Platinum - NForce3 250Gb?

Hi,
I have a MSI K8N Neo Platinum, which uses a NForce3 250Gb chipset. I have read that port multipliers can use either SATA or SATA II hosts and drives, but I don't know if the technology is 100%, transparently compatible.
Is the aforementioned chipset/motherboard compatible with port multiplier technology?
Does it support FIS, which gives the greatest perfomance?
Does it need a BIOS or driver update?
Thanks for the attention
Brazilian Joe

Quote from: syar2003 on 22-February-06, 05:10:37
Hi!
The K8N Neo Platinum (MS-7030) doesn't use -5v to anything.
So the -5v from the old atx spesification is not needed in your case.
WoW, thanks for fast reply!
So, it won't be any problem to use Antecs SmartPower 2.0 450W with this board then? Want to make sure about it, before accept Antecs offer for replacement and had spent over 4 days to find the problem with his computer. Really don't want to do it again.
This is his riggs:
Antec Sonata
AMD 64 3000+ S754
Corsair Value S. PC3200 DDR 512MB
Maxtor Diamondmax 9 250GB SATA
Maxtor Diamondmax 9 IDE 160GB
Sapphire Radeon 9550 Atlantis 128MB DDR
and
Accton ethernet card on PCI slot
MSI D-Bracket2
so
With the "new" Antec SmartPower 2.0 450W
Any problem with this rigg and PSU?
edit:
Dound this post that it said the board do need -5V and now Im confused?
http://www.archivaty.net/forums/about12964-30.html

MSI K8N NEO platinum and MOBILE chips

I just found out a problem with MSI K8N NEO Platinum.
I recently upgraded my cpu from Clawhammer DTR 3200+ 1.5V to Clawhammer Mobile 3400+ 1.4V (hoping for better overclocking). To my surprise the mainboard can no longer raise the VCore voltage over 1.45V (it doesn’t matter if I select in the bios 1.5 or 1.55V). The only working option is raising de VCore by 3.3% 5% 8.3% 10%, resulting in a maximum VCore of 1.45 + 1.45 x 10% = 1.6V
I did some googeling and found there is a VCore issue with the K8N NEO and mobile chips, although DTR chips are fully supported (working VCore and multiplier adjustments).
I am using the latest beta bios 1.56B (moded by Pinochio)
Did any of you found a way to resolve this problem? IT IS DRIVING ME INSANE!!!

Bad post...

Help: MSI K8N Neo Platinum

I've had nothing but problems trying to get this system running properly at any overclocking selections. Can you please review my components and give me suggestions on how to improve my situation.
Currently my know problems are 1. The Mother Board will only read my (2) 200/Gig Hard drives as 127/Gigs. 2. Slighest overclocking & system won't boot up.
Components:
Processor: A64 3200+ NewCastle
MoBo: MSI K8N Neo Platinum
MSI K8N Neo Platinum
Ram: Kingston HyperX 2048 PC3200 400Mhz (2 x 1024MB)
Kinston Ram - Tiger Direct
Video: MSI N5900 Ultra-VTD 256
MSI 5900 Ultra
Hard Drives: (2) 200 Gig Seagates
Power: 500W Aspire
3DMark2001 SE Score: 6300
Ok, everything I bought I got because it said it had Overclocking capabilities. So far any attempts to O.C. the system won't boot up properly.
WHAT DO I DO?
Thoughts on my other components???

The first thing you need to do is tighten them memory timings you killing your a64's performance
try 2.5,3,2,8 t1 2.7v
Get the latest bios for the neo it is a truly fast board when set up right.
Your 3d mark 01 should be in the 15k to 20k range
If you are running 200gb hdds you need to run sp1 on windows xp as xp does not recognise drives over 137gb
run your pci at 67 or 68
drop your htt to 3x
before you try to over clock you system get it running well at stock speeds or you will end up in a mess, there is not much point o/cin if its not.
Msi neo need a bit of tweaking but it runs like a dream when you do.
All your parts look ok

MSI K8N Neo Platinum with Vapochill Case problems - Help anyone. :)

Hi all,
Had a bit of a tricky problem and as Im new to this board I have no idea what could be causing this.
First all all system specs:
Athlon 64 3700+ Clawhammer
MSI K8N Neo Platinum -
1 gig Corsair XMS ProL Low Latency Ram (2 x 512mb)
Nvidia Gefore 6600GT
1 x WD Raptor 10000rpm HD
NEC 2500a DVD writer.
Eye-T 550w PSU.
Vapochill SE Case with installed Vapochill Phase change cooling.
Here are photos of it in its present state, you will notice that it isnt installed in the case at the moment.
The reason for that is because the two wont work together and I want them to so so bad...
So, hopefully someone here can save the day for me - here goes.
I have tested the Motherboard and all other componants outside of the case and everything runs smoothly and there are no problems what so ever, great.
I have also retested the Vapochill case with another motherboard and that also works without a hitch.
The problem comes when I insall the MSI board into the system, all hooked with a really basic setup, PSU, Case cooling, CPU and Ram. Flick the on switch on the power suply and the system turns on for around 1/2 a second then turns off again. I found this strange because it soundnt come on at all until I press the power button.
If I press the power button the same thing will happen over and over.
I have tried a different powersupply and this does nothing at all.
I have checked for shorts and there is no possible way it is shorting on anything.
I have a fan plugged in where the CPU fan would go and this doesnt help.
I have taken it back out and tested it again and it still works ok.
Does this sound familiar to anyone? Are there any secret Bio's menu's that would have an option that would solve this?
Any help would be greatly appreciated.
Glenn

When you are running the MoBo standalone, what are you connecting to the Power, Reset, HDD, etc. pins ? Are you using the wires from the Vapochill case, or something else ? It looks like a single cable with an intermittent switch (red/white cable). I once had a similar sort of problem and it was because I hadn't connected up (the incredibly fiddly) cables correctly. Other than that, I would have gone for a short of some sort - but you have checked that already, so . . . .
As to the system starting to power-up when you switch on the PSU, I wouldn't worry too much about this. It seems to happen from time to time with some of my systems - amongst other things, the BIOS can be set to resume to previous state after a power-fail.

MOVED: MSI K8N Neo Platinum (MS-7030) won't post and just beeps

This topic has been moved to AMD64 nVidia Based board.
MSI K8N Neo Platinum (MS-7030) won't post and just beeps

1)Main Menu - No Post/No Boot problems and fixes - Bios-Central Award Bios Beep Codes + others
2) Memtest86+ As Stated
3) Power Suppy Requirements & Selection
4) Post Specs re Powe supply 3.3v 5v & 12v Amps., Gfx cards Drives etc.,

Corsair Value Select on MSI K8N NEO Platinum Edition

Similar Messages

Maybe you are looking for