Cost of replacing GPS/Bluetooth/Wifi antenna?

I have an iPhone 3GS which has recently stopped picking up GPS signals, and has a weak wifi and bluetooth connection. I find it difficult to tell from this forum whether it is a software/firmware issue, or hardware. However, I'm assuming it is a hardware fault. Does anyone know how much it could cost to get this fixed?
The phone is almost two years old.
Thanks.

Apple only replaces screens and battery's.  Everything else is a full device replacement.
While it may be possible to replace only the radio/antenna, this would not be done via Apple.  Look for a local cell phone repair shop in your area and see if they are capable doing this repair and what they charge.    

Similar Messages

  • Is it possible to replace the internal wifi antenna in a itouch 1st gen with a stronger internal wifi antenna from a slightly newer model, such as a 2nd or 3rd gen itouch?

    Is it possible to replace the internal wifi antenna in a itouch 1st gen with a much stronger internal wifi antenna from a slightly newer model, such as a 2nd or 3rd generation itouch?

    That is not very likely as the antennae are different physical designs and fit will be an issue.

  • After replacing wifi antenna wifi is still dimmed/greyed out.  Bluetooth works fine.  How do i fix this issue? Could there be another part that needs replacing?

    my wifi was greyed out so I replaced the wifi antenna.  I just put the new one in and restored the ipad but the wifi still is greyed out but the Bluetooth works fine.  What could the problem be and how can I fix it?

    This article offers some suggestions which may help: iOS: Wi-Fi or Bluetooth settings grayed out or dim
    This likely has nothing to do with your router.

  • My iPhone 4S was recently replaced as it had a faulty wifi antenna. The new phone no longer syncs iMessage with my ipad like the old one used to.

    My iMessages were always automatically synced with my  6 monthold iPhone 4S. However the phone recently had to be replaced by apple because of a faulty wifi antenna. The new phone was restored from backup. It works fine but iMessage no longer syncs with my ipad. I've looked into the settings and can't see anything wrong? I can iMessage from my phone and iMessage from my ipad but they don't synch. Very frustrating. Would appreciate some help. My nearest spple store is 30 miles away. Thank you so much.

    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
    http://tinyurl.com/a7odey8
    Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/TS4268
    Using FaceTime and iMessage behind a firewall
    http://support.apple.com/kb/HT4245
    iOS: About Messages
    http://support.apple.com/kb/HT3529
    Set up iMessage
    http://www.apple.com/ca/ios/messages/
    Troubleshooting Messages
    http://support.apple.com/kb/TS2755
    Setting Up Multiple iOS Devices for iMessage and Facetime
    http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
    FaceTime and iMessage not accepting Apple ID password
    http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
    Unable to use FaceTime and iMessage with my apple ID
    https://discussions.apple.com/thread/4649373?tstart=90
    For non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
    How to Send SMS from iPad
    http://www.iskysoft.com/apple-ipad/send-sms-from-ipad.html
     Cheers, Tom

  • Cost of Replacing Logic Board at Apple Store

    At the current moment, my 13" macbook pro no longer recognizes the wifi hardware. Running OSX 10.10, I thought this was the root of the problem. Support helped and solved the issue but it quit the minute I hung up the phone. It is possible that I will need to replace the logic board in order to get everything working again (although I may just buy a wifi adapter) and was wondering what the cost of replacing a macbook pro 8.1 logic board is, just so I don't have a heart attack in the store. Thanks.

    Logic boards typically run $500 and up...take the the MBP to an Apple store genius bar and have the techs run their diagnostics to determine the exact issue.  They can then quote an accurate price if physical repair is needed.

  • Homebrew WiFi Antenna (Proper Cable, LMR-195 GR-58?)

    Hey,
    I don't know if this is the best forum for my questions, and if not please direct me to one that better suits my needs. I was simply referred to this forum through another one. Anyhow, me and my friend are attempting to build our own wifi antenna and after searching google for a while we have come up dry on a couple things.
    1), From the wifi card we wish to attach a cable that will be say 25-50 ft in length which will then attach to the card's reg 3 inch antenna, pretty much extending the antenna from the card. What is the best cable to do this. Originally we were told to use GR-58 50 Ohm Coax cable however after reading further we found that would only be good for 3-4 ft before it pretty much "spills the connection all over the place". We were then recommended to use LMR-195 or better though what type of cable is this as it does not seem to be supplied by Radio Shack. The question is what cable would you guys recomend that could hold a wi-fi signal 25-50 ft from the end of the antenna on one end back into the wifi card on the other, and where can we purchase it?
    Thanks in advance and if this is not a good forum for these questions please direct me to another. As time goes on we will build our own antenna but right now we want to get the reg antenna to work over a decent length of cable.

    OK. Understood. You have a massive challenge ahead of you. Also be warned that an external antenna that is not properly protected and grounded can be a fire and safety hazard, and that it can accumulate enough of a static charge in dry, windy environmants to blow up your system (not so much like "boom" , but static electricity is deadly to most semiconductors).
    Next, you may want to study on how to make a BALUN / UNUN because the WiFI stuff is 50 Ohm impedence, and your average TV antenna is 300 Ohm (assuming it's a classic LPDA - Log Periodic Dipole Array).
    An LPDA for TV will have some elements for ~50 MHz, 260 Mhz, 512MHz, and if it's also a UHF antenna, it might be good up into the 900 MHz ranges. LPDA ware pretty wide spectrum, and you'll probably luck out and hit a harmonic somewhere.
    You'll need to craft a 6:1 balun, not that big of a deal actually. Shop some of the amateur radio sites (like aesham.com) for materials or to just buy a 6:1 BALUN.
    The Gain of a typical ~ 6 ft LPDA could likely provide enough gain to make the system work =-->IF<--= the cabling is very high quality, the cable termination is nearly perfect, your BALUN is efficient enough, and you don't lose too much signal through the protection system (that would be the protection system against lightning and static ... includes a thingy called a "lightning arrestor" that in no way, form, or fashion could do anything to stop lightning).
    By the way, you'll want to bring that TV antenna down and clean every connection on every element. Any noisy junction will kill your signal.
    All-in-all, the cable shouldn't cost you more than a couple hundred dollars, the materials for the BALUN another ~US$10-20, connectors another US$20-50, protection elements, maybe another US$25-100 depending on who and what you go with.
    Here's a link with some good info regarding wireless signal propagation, 802.11, and antenna stuff.
    http://www.cisco.com/en/US/products/hw/wireless/ps469/products_data_sheet09186a008008883b.html
    Good Luck, make it a great learning experience!
    Scott

  • Mini 210-3080NR dont accept bluetooth + wifi card from another HP Mini !?

    i am have purchased  one new HP Mini 210-3080NR and this have only wifi mini pci-e and need a bluetooth on this to use with my phones,i am have another mini HP models as > 210-1076NR and 110-3130NR and this 2 models have the same mini pci-e bluetooth + wifi card,i am removed the card from mini 110-3130br and put on my 210-3080nr and appears as refused hardware or imcompatible,but if put the card from mini 210-1076nr its Ok ! HP put different firmware on the same card for different models ? and have another doubt,the mini 210-3080nr not have socket for additional mini pci-e to put for example > broadcom crystal hd decoder !!!??? i dont understand this because this model have special sound as beats audio and design exclusive for this model but HP has cutted resources > no mini pci slot to additional card and not have bluetooth + wifi.
    b.r.
    wait for reply to have solution to conflict of cards.

    Does the PC still have Windows 7 installed?  Did you install the driver found HERE.  In the intial post, it is not stated if the netbook had a similar card installed or not.  Was this a replacement or an additon?
    {---------- Please click the "Thumbs Up" to say thanks for helping.
    Please click "Accept As Solution" if my help has solved your problem. ----------}
    This is a user supported forum. I am a volunteer and I do not work for HP.

  • How much iphone 4s wifi chip cost?Still my 4s wifi is not working even though I already updated it to ios7. Thank You!!!..

    How much iphone 4s wifi chip cost?Still my 4s wifi is not working even though I already updated it to ios7. Thank You!!!..

    You cannot replace just the chip. If all of the various solutions suggested in Apple's support documents and here in these forums do not help, you will need to 1) take or send your iPhone to Apple for replacement, 2) pay to have an unauthorized third-party shop attempt repairs, or 3) attempt repairs yourself. The latter two options will void any further support from Apple.
    Regards.

  • Problems with camera, wifi antenna and battery

    where can i get help for my problem?

    Hello omarcortes13,
    Thanks for contributing to the Apple Support Communities.
    It sounds like you are seeing issues with your iPhone 5 camera, wifi antenna and battery. I know it can be frustrating when hardware features are not behaving normally, and I have some resources that can help troubleshoot your iPhone.
    You can find some very useful troubleshooting tips for the areas you mentioned at this link:
    Get help with hardware features on your iPhone, iPad, and iPod touch - Apple Support
    Camera
    Camera isn't working or has undesired image quality
    Wi-Fi and Bluetooth issues
    Issues with Wi-Fi networks and connection
    Wi-Fi or Bluetooth settings grayed our or dim
    Battery or charging issues
    Get help charging your iPhone, iPad, or iPod touch
    These links should provide a helpful starting point for troubleshooting. If the links I've mentioned don't resolve the situation, the article above suggests contacting Apple Support for more help.
    If you still have an issue with your device, contact Apple Support.
    Sincerely,
    Jeremy

  • Can i use my playbook as a GPS without wifi niether bridge connection?

    can i use my playbook as a GPS without wifi niether bridge connection?
    please help me!!!
    Solved!
    Go to Solution.

    @vanawful, the GPS capability comes from the TI WiLink 7 chip (WL-1283) that provides all the wireless capabilities for the WiFi-only PlayBook.
    Although the jury's still out on whether different units may behave differently, so far it appears likely every unit *can* work, under the right conditions, but problems in the software (OS level) or possibly in the chip itself (nobody's saying yet) mean that it's quite unreliable.
    There is no need to have WiFi enabled for it, and I've used the GPS frequently now with WiFi off and no nearby hotspots, no tethering (I don't even have a smartphone), and just the GPS running.
    If you pick a clear day (i.e. no big rain clouds off to the south, etc), are out in the open without buildings or other things blocking the view of the sky, make certain you are not covering up the lower-right corner of the PlayBook where it appears the GPS antenna is, run the Compass app, and let it sit for 5-10 minutes (if this is your first time using it) so it can find and download ephemeris data from each satellite, you should see it start reporting lat/long positions after that.
    If you do this, and it doesn't work, try again. Then try again. Maybe try another time. Preferably do this on different days too, and possibly after a reboot. Yes, it appears to be that flaky sometimes...
    I've written my own GPS recording app (no fancy map... just records the readings) and done numerous tests at this point. The readings, when they arrive, are generally exceptionally good. The main problem is getting them to actually arrive and, so far, I've found nothing that can force the issue. Even with my own app, I sometimes have to start it up and leave it alone for some minutes, 4-5 times, before I get the first reading, and there are days I've just given up and moved on. The next day it will simply work. It's largely random.
    The three single biggest things you need to remember to get any readings: be outdoors away from big buildings, don't pick a heavily overcast day, and do NOT hold the unit with your right hand covering the bottom right corner (when held in the default landscape orientation with the cameras on top, that is).
    Peter Hansen -- (BB10 and dev-related blog posts at http://peterhansen.ca.)
    Author of White Noise and Battery Guru for BB10 and for PlayBook | Get more from your battery!

  • How much does it cost to replace the lid of a MBP 13"?

    Hi,
    I've got myself a Macbook Pro 13" (Mid-2009) that has got a fair few scratches in one corner and some noticeable dents on the lid. The top and bottom casing are all new after getting it repaired under AppleCare.
    I was wondering how much the lid would cost to replace (so my whole casing is in tip-top condition) and whether that includes the LCD as well. I know its going to be expensive and have already explored ifixit.com and other vendors for fixing it on the Internet and I'm not fond of just buying a case like a hardshell just to cover it up.
    So if anyone has had it done by Apple or knows roughly how much it would cost to replace then that would be great!
    Thanks

    I can tell you this, Apple will be the most expensive choice, but you'd have to make a genius bar appointment to get a price. Also, look here:
    http://www.powerbookmedic.com/

  • Cost of replacing a broken or stolen iPhone?

    I'm planning to buy the iPhone when it comes out on O2 in the UK, but I'm a little unclear about whether the cost of the iPhone itself is subsidised or just a standard purchase.
    In the UK it's common to get a phone free or cheap when taking out a contract. If the phone gets damaged or stolen, then the cost of buying a replacement (if it's not insured) is substantially more than the original price.
    Does anyone know what the situation is with the iPhone - anyone using AT&T had such an incident? Can you go out and buy another iPhone and carry on using it with your existing contract, or do you have to pay a higher price for a replacement.
    Along a similar line, if Apple were to bring out a better version of the iPhone in future, would existing customers have to wait for their contracts to end before getting the upgrade, or could they simply buy the new phone and continue with their existing iPhone tarriff?
    Message was edited by: bilbo_baggins

    I would presume that the cost of replacement is just the normal cost of the phone - but there is no information to confirm this - that is why I'm a little unclear.
    The reason for wanting to know is so I can decide on whether it's worth considering insurance, cases etc. If it's simply a case of buying another iPhone then fair enough - if it turns out that you cannot buy another iPhone without signing up to an additional contract (and so paying two lots of £35 per month) or paying vastly more than the initial purchase price for a replacement, then I would be far more concerned about protecting my iPhone.
    Really it's a balance between cost of insurance vs risking it, and the bulkiness and inconvenience of using a case vs increased risk of damage.
    Message was edited by: bilbo_baggins

  • Cost of replacing hard drive on my powerbook G4

    I bought my powerbook about 2 years ago and to be honest, have loved it a lot. Today after a coffee break, I sat to work on my PB and it was very slow...then began a host of problems which have ended with it not starting up. I have done disk utility tests which found a problem with my hard drive that it couldn't repair. I am also unable to reinstall OS. A hardware test revealed that there is an error with my hard drive. My important documents have been backed up so am not too upset about that but I don't want to spend heaps of cash getting it repaired. For those Aussies out there, would anybody know the approximate cost of replacing the hard drive? Would it be cheaper to buy the HDD myself and try to replace it myself. I could get the IT guys from where I work to replace it. And yes, my PB is out of warranty! Also, should I aim to replace this HDD with the same one thats now busted, or should I replace it with a better one. Apart from increased space, what other benefits would an upgraded HDD give me (I have a 60 GB hard drive, 1.33 GHz).

    miabbate
    My sentiments are very similar to Matt's, though my hard drive experiences have tended to be with either Seagate or Hitachi products. Generally I would also agree that another Toshiba drive is to be avoided.
    For cache, it is always better to go for more - minimum of 8MB. As a very broad indication of what to purchase, something along the lines of 8MB, 5400RPM, 80-120GB.
    Also be aware that not all drives are the same, even if their general specifications are the same. For example, Hitachi produce different versions of their 7200 RPM 100GB Travelstar - not only in Ultra ATA and Serial ATA versions, but also a version designed for extended power-on usage. Drives from different manufacturers may also have varying technologies built into them. Something else to consider is the length of warranty. Some manufacturers offer longer terms than others.
    15" 1.25GHz/12" 1GHz PBs, 2xPPC Mac minis, 12" iBook G4,   Mac OS X (10.4.6)   Cube, 2xTAMs, iPods 2G/4G, iPs, AEBS, AX

  • Cost of replacing iPad1 battery in Australia?

    My iPad1 battery has just failed after only 12 months and ~200 recharge cycles. What is the cost of replacing it in Australia (Sydney) since it is only US$99 in the States and our exchange rate is A$1.05=US$1.00?

    Service arranged through Apple costs $109 AUD. A $19.95 AUD shipping fee will be added if you arrange service online or by calling Apple Technical Support. All fees are in AUD and include GST.
    http://support.apple.com/kb/index?page=servicefaq&geo=Australia&product=iphone
    BTW, the US price foes not include sales taxes which can add up to 10% to the cost.

  • Cost Of Replacing Hard Drive On 4th Gen iPod

    I just want to know the cost of replacing the hard drive on my 20 GB iPod, 4th generation. Is it worth repairing or should I just buy a new one?

    apple's price is here... http://docs.info.apple.com/article.html?artnum=304869#faq14
    search with google/whatever for "ipod repair" and you'll find a number of companies offering repair services at various prices
    a new one might be a better investment

Maybe you are looking for

  • How do I make the picture look grainy?

    I want to go for an old film look. Specifically, a grainy effect if possible. How would I do that? Thanks for your help!

  • Migration an application from JDeveloper 10.1.3.2 to JDeveloper 11.1.1.2.0

    I have a project done using JDeveloper 10.1.3.2 and it contains a folder called lib. There are two .jar files named "adf-faces-impl" and "jsf-impl" After the migration I can see the lib folder in JDeveloper 11g but there isn't anything inside. Some f

  • Dynamic columns in datatable...

    Hi guys, i've a question about datatable. I have to use datatable for inserting data into db. My question is: I'm developed a datatable with 5 columns and various rows,i've create an actionlistener and when i click it each row is successfully inserte

  • How do I move focus from date chooser bean to JTable?

    Here's the scenario: I have a panel containing a date chooser bean which is in the north of my main frame. I have a JTable (inside a scroll pane) which is in the center of my main frame. The table (through it's table model) is a registered listener o

  • Parsing MIME message

    Hi, I have a saved email message in MIME format. Some of the emails have attachments encoded using base64. I want to parse the message and extract these attachments. I started doing this in my class by looking for pattern only to realize that these m